diff options
Diffstat (limited to 'arch/arm/mach-at91/board-sam9rlek.c')
| -rw-r--r-- | arch/arm/mach-at91/board-sam9rlek.c | 204 |
1 files changed, 204 insertions, 0 deletions
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c new file mode 100644 index 00000000000..30c79aca84d --- /dev/null +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -0,0 +1,204 @@ +/* + * Copyright (C) 2005 SAN People + * Copyright (C) 2007 Atmel Corporation + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive for + * more details. + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> +#include <linux/fb.h> +#include <linux/clk.h> + +#include <video/atmel_lcdc.h> + +#include <asm/hardware.h> +#include <asm/setup.h> +#include <asm/mach-types.h> +#include <asm/irq.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> +#include <asm/mach/irq.h> + +#include <asm/arch/board.h> +#include <asm/arch/gpio.h> +#include <asm/arch/at91sam926x_mc.h> + +#include "generic.h" + + +/* + * Serial port configuration. + * 0 .. 3 = USART0 .. USART3 + * 4 = DBGU + */ +static struct at91_uart_config __initdata ek_uart_config = { + .console_tty = 0, /* ttyS0 */ + .nr_tty = 2, + .tty_map = { 4, 0, -1, -1, -1 } /* ttyS0, ..., ttyS4 */ +}; + +static void __init ek_map_io(void) +{ + /* Initialize processor: 12.000 MHz crystal */ + at91sam9rl_initialize(12000000); + + /* Setup the serial ports and console */ + at91_init_serial(&ek_uart_config); +} + +static void __init ek_init_irq(void) +{ + at91sam9rl_init_interrupts(NULL); +} + + +/* + * MCI (SD/MMC) + */ +static struct at91_mmc_data __initdata ek_mmc_data = { + .wire4 = 1, + .det_pin = AT91_PIN_PA15, +// .wp_pin = ... not connected +// .vcc_pin = ... not connected +}; + + +/* + * NAND flash + */ +static struct mtd_partition __initdata ek_nand_partition[] = { + { + .name = "Partition 1", + .offset = 0, + .size = 256 * 1024, + }, + { + .name = "Partition 2", + .offset = 256 * 1024 , + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_partitions(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(ek_nand_partition); + return ek_nand_partition; +} + +static struct at91_nand_data __initdata ek_nand_data = { + .ale = 21, + .cle = 22, +// .det_pin = ... not connected + .rdy_pin = AT91_PIN_PD17, + .enable_pin = AT91_PIN_PB6, + .partition_info = nand_partitions, + .bus_width_16 = 0, +}; + + +/* + * SPI devices + */ +static struct spi_board_info ek_spi_devices[] = { + { /* DataFlash chip */ + .modalias = "mtd_dataflash", + .chip_select = 0, + .max_speed_hz = 15 * 1000 * 1000, + .bus_num = 0, + }, +}; + + +/* + * LCD Controller + */ +#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE) +static struct fb_videomode at91_tft_vga_modes[] = { + { + .name = "TX09D50VM1CCA @ 60", + .refresh = 60, + .xres = 240, .yres = 320, + .pixclock = KHZ2PICOS(4965), + + .left_margin = 1, .right_margin = 33, + .upper_margin = 1, .lower_margin = 0, + .hsync_len = 5, .vsync_len = 1, + + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, + .vmode = FB_VMODE_NONINTERLACED, + }, +}; + +static struct fb_monspecs at91fb_default_monspecs = { + .manufacturer = "HIT", + .monitor = "TX09D50VM1CCA", + + .modedb = at91_tft_vga_modes, + .modedb_len = ARRAY_SIZE(at91_tft_vga_modes), + .hfmin = 15000, + .hfmax = 64000, + .vfmin = 50, + .vfmax = 150, +}; + +#define AT91SAM9RL_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \ + | ATMEL_LCDC_DISTYPE_TFT \ + | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE) + +static void at91_lcdc_power_control(int on) +{ + if (on) + at91_set_gpio_value(AT91_PIN_PA30, 0); /* power up */ + else + at91_set_gpio_value(AT91_PIN_PA30, 1); /* power down */ +} + +/* Driver datas */ +static struct atmel_lcdfb_info __initdata ek_lcdc_data = { + .default_bpp = 16, + .default_dmacon = ATMEL_LCDC_DMAEN, + .default_lcdcon2 = AT91SAM9RL_DEFAULT_LCDCON2, + .default_monspecs = &at91fb_default_monspecs, + .atmel_lcdfb_power_control = at91_lcdc_power_control, + .guard_time = 1, +}; + +#else +static struct atmel_lcdfb_info __initdata ek_lcdc_data; +#endif + + +static void __init ek_board_init(void) +{ + /* Serial */ + at91_add_device_serial(); + /* I2C */ + at91_add_device_i2c(); + /* NAND */ + at91_add_device_nand(&ek_nand_data); + /* SPI */ + at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); + /* MMC */ + at91_add_device_mmc(0, &ek_mmc_data); + /* LCD Controller */ + at91_add_device_lcdc(&ek_lcdc_data); +} + +MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK") + /* Maintainer: Atmel */ + .phys_io = AT91_BASE_SYS, + .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, + .boot_params = AT91_SDRAM_BASE + 0x100, + .timer = &at91sam926x_timer, + .map_io = ek_map_io, + .init_irq = ek_init_irq, + .init_machine = ek_board_init, +MACHINE_END |