1 files changed, 0 insertions, 294 deletions
diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c
deleted file mode 100644
index e825641a1de..00000000000
--- a/arch/arm/mach-at91/board-stamp9g20.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
- *  Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
- *                     taskit GmbH
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/mm.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/w1-gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-void __init stamp9g20_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * NAND flash
- */
-static struct atmel_nand_data __initdata nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.bus_width_16	= 0,
-	.det_pin	= -EINVAL,
-	.ecc_mode	= NAND_ECC_SOFT,
-};
-
-static struct sam9_smc_config __initdata nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 3,
-};
-
-static void __init add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &nand_smc_config);
-
-	at91_add_device_nand(&nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata mmc_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -1,
-		.wp_pin		= -1,
-	},
-};
-
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata portuxg20_udc_data = {
-	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
-	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA28,
-	.is_rmii	= 1,
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led portuxg20_leds[] = {
-	{
-		.name			= "LED2",
-		.gpio			= AT91_PIN_PC5,
-		.default_trigger	= "none",
-	}, {
-		.name			= "LED3",
-		.gpio			= AT91_PIN_PC4,
-		.default_trigger	= "none",
-	}, {
-		.name			= "LED4",
-		.gpio			= AT91_PIN_PC10,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-static struct gpio_led stamp9g20evb_leds[] = {
-	{
-		.name			= "D8",
-		.gpio			= AT91_PIN_PB18,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}, {
-		.name			= "D9",
-		.gpio			= AT91_PIN_PB19,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	}, {
-		.name			= "D10",
-		.gpio			= AT91_PIN_PB20,
-		.active_low		= 1,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-
-/*
- * SPI devices
- */
-static struct spi_board_info portuxg20_spi_devices[] = {
-	{
-		.modalias	= "spidev",
-		.chip_select	= 0,
-		.max_speed_hz	= 1 * 1000 * 1000,
-		.bus_num	= 0,
-	}, {
-		.modalias	= "spidev",
-		.chip_select	= 0,
-		.max_speed_hz	= 1 * 1000 * 1000,
-		.bus_num	= 1,
-	},
-};
-
-
-/*
- * Dallas 1-Wire
- */
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	.pin		= AT91_PIN_PA29,
-	.is_open_drain	= 1,
-	.ext_pullup_enable_pin	= -EINVAL,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-void add_w1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-
-void __init stamp9g20_board_init(void)
-{
-	/* Serial */
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-	at91_add_device_serial();
-	/* NAND */
-	add_device_nand();
-	/* MMC */
-	at91_add_device_mci(0, &mmc_data);
-	/* W1 */
-	add_w1();
-}
-
-static void __init portuxg20_board_init(void)
-{
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx, Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-	stamp9g20_board_init();
-	/* USB Host */
-	at91_add_device_usbh(&usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&portuxg20_udc_data);
-	/* Ethernet */
-	at91_add_device_eth(&macb_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* SPI */
-	at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
-	/* LEDs */
-	at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds));
-}
-
-static void __init stamp9g20evb_board_init(void)
-{
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-						| ATMEL_UART_DTR | ATMEL_UART_DSR
-						| ATMEL_UART_DCD | ATMEL_UART_RI);
-	stamp9g20_board_init();
-	/* USB Host */
-	at91_add_device_usbh(&usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&stamp9g20evb_udc_data);
-	/* Ethernet */
-	at91_add_device_eth(&macb_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* LEDs */
-	at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
-}
-
-MACHINE_START(PORTUXG20, "taskit PortuxG20")
-	/* Maintainer: taskit GmbH */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= stamp9g20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= portuxg20_board_init,
-MACHINE_END
-
-MACHINE_START(STAMP9G20, "taskit Stamp9G20")
-	/* Maintainer: taskit GmbH */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= stamp9g20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= stamp9g20evb_board_init,
-MACHINE_END