diff options
Diffstat (limited to 'arch/arm/mach-clps711x/include/mach/hardware.h')
| -rw-r--r-- | arch/arm/mach-clps711x/include/mach/hardware.h | 237 |
1 files changed, 237 insertions, 0 deletions
diff --git a/arch/arm/mach-clps711x/include/mach/hardware.h b/arch/arm/mach-clps711x/include/mach/hardware.h new file mode 100644 index 00000000000..4c3e101b96c --- /dev/null +++ b/arch/arm/mach-clps711x/include/mach/hardware.h @@ -0,0 +1,237 @@ +/* + * arch/arm/mach-clps711x/include/mach/hardware.h + * + * This file contains the hardware definitions of the Prospector P720T. + * + * Copyright (C) 2000 Deep Blue Solutions Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + + +#define CLPS7111_VIRT_BASE 0xff000000 +#define CLPS7111_BASE CLPS7111_VIRT_BASE + +/* + * The physical addresses that the external chip select signals map to is + * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212 + * processors. CONFIG_EP72XX_BOOT_ROM is only available if these + * processors are in use. + */ +#ifndef CONFIG_EP72XX_ROM_BOOT +#define CS0_PHYS_BASE (0x00000000) +#define CS1_PHYS_BASE (0x10000000) +#define CS2_PHYS_BASE (0x20000000) +#define CS3_PHYS_BASE (0x30000000) +#define CS4_PHYS_BASE (0x40000000) +#define CS5_PHYS_BASE (0x50000000) +#define CS6_PHYS_BASE (0x60000000) +#define CS7_PHYS_BASE (0x70000000) +#else +#define CS0_PHYS_BASE (0x70000000) +#define CS1_PHYS_BASE (0x60000000) +#define CS2_PHYS_BASE (0x50000000) +#define CS3_PHYS_BASE (0x40000000) +#define CS4_PHYS_BASE (0x30000000) +#define CS5_PHYS_BASE (0x20000000) +#define CS6_PHYS_BASE (0x10000000) +#define CS7_PHYS_BASE (0x00000000) +#endif + +#if defined (CONFIG_ARCH_EP7211) + +#define EP7211_VIRT_BASE CLPS7111_VIRT_BASE +#define EP7211_BASE CLPS7111_VIRT_BASE +#include <asm/hardware/ep7211.h> + +#elif defined (CONFIG_ARCH_EP7212) + +#define EP7212_VIRT_BASE CLPS7111_VIRT_BASE +#define EP7212_BASE CLPS7111_VIRT_BASE +#include <asm/hardware/ep7212.h> + +#endif + +#define SYSPLD_VIRT_BASE 0xfe000000 +#define SYSPLD_BASE SYSPLD_VIRT_BASE + +#ifndef __ASSEMBLER__ + +#define PCIO_BASE IO_BASE + +#endif + + +#if defined (CONFIG_ARCH_AUTCPU12) + +#define CS89712_VIRT_BASE CLPS7111_VIRT_BASE +#define CS89712_BASE CLPS7111_VIRT_BASE + +#include <asm/hardware/clps7111.h> +#include <asm/hardware/ep7212.h> +#include <asm/hardware/cs89712.h> + +#endif + + +#if defined (CONFIG_ARCH_CDB89712) + +#include <asm/hardware/clps7111.h> +#include <asm/hardware/ep7212.h> +#include <asm/hardware/cs89712.h> + +/* dynamic ioremap() areas */ +#define FLASH_START 0x00000000 +#define FLASH_SIZE 0x800000 +#define FLASH_WIDTH 4 + +#define SRAM_START 0x60000000 +#define SRAM_SIZE 0xc000 +#define SRAM_WIDTH 4 + +#define BOOTROM_START 0x70000000 +#define BOOTROM_SIZE 0x80 +#define BOOTROM_WIDTH 4 + + +/* static cdb89712_map_io() areas */ +#define REGISTER_START 0x80000000 +#define REGISTER_SIZE 0x4000 +#define REGISTER_BASE 0xff000000 + +#define ETHER_START 0x20000000 +#define ETHER_SIZE 0x1000 +#define ETHER_BASE 0xfe000000 + +#endif + + +#if defined (CONFIG_ARCH_EDB7211) + +/* + * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3) + * and repeat across it. This is the mapping for it. + * + * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This + * was cause for much consternation and headscratching. This should probably + * be made a compile/run time kernel option. + */ +#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE /* physical */ + +#define EP7211_VIRT_EXTKBD (0xfd000000) /* virtual */ + + +/* + * The CS8900A ethernet chip has its I/O registers wired to chip select 2 + * (nCS2). This is the mapping for it. + * + * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This + * was cause for much consternation and headscratching. This should probably + * be made a compile/run time kernel option. + */ +#define EP7211_PHYS_CS8900A CS2_PHYS_BASE /* physical */ + +#define EP7211_VIRT_CS8900A (0xfc000000) /* virtual */ + + +/* + * The two flash banks are wired to chip selects 0 and 1. This is the mapping + * for them. + * + * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running + * in jumpered boot mode. + */ +#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE /* physical */ +#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE /* physical */ + +#define EP7211_VIRT_FLASH1 (0xfa000000) /* virtual */ +#define EP7211_VIRT_FLASH2 (0xfb000000) /* virtual */ + +#endif /* CONFIG_ARCH_EDB7211 */ + + +/* + * Relevant bits in port D, which controls power to the various parts of + * the LCD on the EDB7211. + */ +#define EDB_PD1_LCD_DC_DC_EN (1<<1) +#define EDB_PD2_LCDEN (1<<2) +#define EDB_PD3_LCDBL (1<<3) + + +#if defined (CONFIG_ARCH_CEIVA) + +#define CEIVA_VIRT_BASE CLPS7111_VIRT_BASE +#define CEIVA_BASE CLPS7111_VIRT_BASE + +#include <asm/hardware/clps7111.h> +#include <asm/hardware/ep7212.h> + + +/* + * The two flash banks are wired to chip selects 0 and 1. This is the mapping + * for them. + * + * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running + * in jumpered boot mode. + */ +#define CEIVA_PHYS_FLASH1 CS0_PHYS_BASE /* physical */ +#define CEIVA_PHYS_FLASH2 CS1_PHYS_BASE /* physical */ + +#define CEIVA_VIRT_FLASH1 (0xfa000000) /* virtual */ +#define CEIVA_VIRT_FLASH2 (0xfb000000) /* virtual */ + +#define CEIVA_FLASH_SIZE 0x100000 +#define CEIVA_FLASH_WIDTH 2 + +#define SRAM_START 0x60000000 +#define SRAM_SIZE 0xc000 +#define SRAM_WIDTH 4 + +#define BOOTROM_START 0x70000000 +#define BOOTROM_SIZE 0x80 +#define BOOTROM_WIDTH 4 + +/* + * SED1355 LCD controller + */ +#define CEIVA_PHYS_SED1355 CS2_PHYS_BASE +#define CEIVA_VIRT_SED1355 (0xfc000000) + +/* + * Relevant bits in port D, which controls power to the various parts of + * the LCD on the Ceiva Photo Max, and reset to the LCD controller. + */ + +// Reset line to SED1355 (must be high to operate) +#define CEIVA_PD1_LCDRST (1<<1) +// LCD panel enable (set to one, to enable LCD) +#define CEIVA_PD4_LCDEN (1<<4) +// Backlight (set to one, to turn on backlight +#define CEIVA_PD5_LCDBL (1<<5) + +/* + * Relevant bits in port B, which report the status of the buttons. + */ + +// White button +#define CEIVA_PB4_WHT_BTN (1<<4) +// Black button +#define CEIVA_PB0_BLK_BTN (1<<0) +#endif // #if defined (CONFIG_ARCH_CEIVA) + +#endif |