diff options
Diffstat (limited to 'arch/arm/mach-davinci')
45 files changed, 2846 insertions, 404 deletions
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 40866c643f1..033bfede6b6 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -32,11 +32,13 @@ config ARCH_DAVINCI_DA830 bool "DA830/OMAP-L137 based system" select CP_INTC select ARCH_DAVINCI_DA8XX + select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1 config ARCH_DAVINCI_DA850 bool "DA850/OMAP-L138 based system" select CP_INTC select ARCH_DAVINCI_DA8XX + select ARCH_HAS_CPUFREQ config ARCH_DAVINCI_DA8XX bool @@ -63,6 +65,13 @@ config MACH_SFFSDR Say Y here to select the Lyrtech Small Form Factor Software Defined Radio (SFFSDR) board. +config MACH_NEUROS_OSD2 + bool "Neuros OSD2 Open Television Set Top Box" + depends on ARCH_DAVINCI_DM644x + help + Configure this option to specify the whether the board used + for development is a Neuros OSD2 Open Set Top Box. + config MACH_DAVINCI_DM355_EVM bool "TI DM355 EVM" default ARCH_DAVINCI_DM355 @@ -98,16 +107,66 @@ config MACH_DAVINCI_DA830_EVM bool "TI DA830/OMAP-L137 Reference Platform" default ARCH_DAVINCI_DA830 depends on ARCH_DAVINCI_DA830 + select GPIO_PCF857X help Say Y here to select the TI DA830/OMAP-L137 Evaluation Module. +choice + prompt "Select DA830/OMAP-L137 UI board peripheral" + depends on MACH_DAVINCI_DA830_EVM + help + The presence of UI card on the DA830/OMAP-L137 EVM is detected + automatically based on successful probe of the I2C based GPIO + expander on that board. This option selected in this menu has + an effect only in case of a successful UI card detection. + +config DA830_UI_LCD + bool "LCD" + help + Say Y here to use the LCD as a framebuffer or simple character + display. + +config DA830_UI_NAND + bool "NAND flash" + help + Say Y here to use the NAND flash. Do not forget to setup + the switch correctly. +endchoice + config MACH_DAVINCI_DA850_EVM bool "TI DA850/OMAP-L138 Reference Platform" default ARCH_DAVINCI_DA850 depends on ARCH_DAVINCI_DA850 + select GPIO_PCA953X help Say Y here to select the TI DA850/OMAP-L138 Evaluation Module. +choice + prompt "Select peripherals connected to expander on UI board" + depends on MACH_DAVINCI_DA850_EVM + help + The presence of User Interface (UI) card on the DA850/OMAP-L138 + EVM is detected automatically based on successful probe of the I2C + based GPIO expander on that card. This option selected in this + menu has an effect only in case of a successful UI card detection. + +config DA850_UI_NONE + bool "No peripheral is enabled" + help + Say Y if you do not want to enable any of the peripherals connected + to TCA6416 expander on DA850/OMAP-L138 EVM UI card + +config DA850_UI_RMII + bool "RMII Ethernet PHY" + help + Say Y if you want to use the RMII PHY on the DA850/OMAP-L138 EVM. + This PHY is found on the UI daughter card that is supplied with + the EVM. + NOTE: Please take care while choosing this option, MII PHY will + not be functional if RMII mode is selected. + +endchoice + config DAVINCI_MUX bool "DAVINCI multiplexing support" depends on ARCH_DAVINCI diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index 2e11e847313..eeb9230d884 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -23,9 +23,14 @@ obj-$(CONFIG_CP_INTC) += cp_intc.o # Board specific obj-$(CONFIG_MACH_DAVINCI_EVM) += board-dm644x-evm.o obj-$(CONFIG_MACH_SFFSDR) += board-sffsdr.o +obj-$(CONFIG_MACH_NEUROS_OSD2) += board-neuros-osd2.o obj-$(CONFIG_MACH_DAVINCI_DM355_EVM) += board-dm355-evm.o obj-$(CONFIG_MACH_DM355_LEOPARD) += board-dm355-leopard.o obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM) += board-dm646x-evm.o obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o + +# Power Management +obj-$(CONFIG_CPU_FREQ) += cpufreq.o +obj-$(CONFIG_CPU_IDLE) += cpuidle.o diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index bfbb63936f3..31dc9901e55 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -10,51 +10,194 @@ * or implied. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> #include <linux/console.h> +#include <linux/interrupt.h> +#include <linux/gpio.h> +#include <linux/platform_device.h> #include <linux/i2c.h> +#include <linux/i2c/pcf857x.h> #include <linux/i2c/at24.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <mach/common.h> -#include <mach/irqs.h> #include <mach/cp_intc.h> +#include <mach/mux.h> +#include <mach/nand.h> #include <mach/da8xx.h> -#include <mach/asp.h> +#include <mach/usb.h> #define DA830_EVM_PHY_MASK 0x0 #define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ -static struct at24_platform_data da830_evm_i2c_eeprom_info = { - .byte_len = SZ_256K / 8, - .page_size = 64, - .flags = AT24_FLAG_ADDR16, - .setup = davinci_get_mac_addr, - .context = (void *)0x7f00, -}; +#define DA830_EMIF25_ASYNC_DATA_CE3_BASE 0x62000000 +#define DA830_EMIF25_CONTROL_BASE 0x68000000 -static struct i2c_board_info __initdata da830_evm_i2c_devices[] = { - { - I2C_BOARD_INFO("24c256", 0x50), - .platform_data = &da830_evm_i2c_eeprom_info, - }, - { - I2C_BOARD_INFO("tlv320aic3x", 0x18), - } +/* + * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4]. + */ +#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15) +#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4) + +static const short da830_evm_usb11_pins[] = { + DA830_GPIO1_15, DA830_GPIO2_4, + -1 }; -static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = { - .bus_freq = 100, /* kHz */ - .bus_delay = 0, /* usec */ +static da8xx_ocic_handler_t da830_evm_usb_ocic_handler; + +static int da830_evm_usb_set_power(unsigned port, int on) +{ + gpio_set_value(ON_BD_USB_DRV, on); + return 0; +} + +static int da830_evm_usb_get_power(unsigned port) +{ + return gpio_get_value(ON_BD_USB_DRV); +} + +static int da830_evm_usb_get_oci(unsigned port) +{ + return !gpio_get_value(ON_BD_USB_OVC); +} + +static irqreturn_t da830_evm_usb_ocic_irq(int, void *); + +static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler) +{ + int irq = gpio_to_irq(ON_BD_USB_OVC); + int error = 0; + + if (handler != NULL) { + da830_evm_usb_ocic_handler = handler; + + error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED | + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "OHCI over-current indicator", NULL); + if (error) + printk(KERN_ERR "%s: could not request IRQ to watch " + "over-current indicator changes\n", __func__); + } else + free_irq(irq, NULL); + + return error; +} + +static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = { + .set_power = da830_evm_usb_set_power, + .get_power = da830_evm_usb_get_power, + .get_oci = da830_evm_usb_get_oci, + .ocic_notify = da830_evm_usb_ocic_notify, + + /* TPS2065 switch @ 5V */ + .potpgt = (3 + 1) / 2, /* 3 ms max */ }; +static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id) +{ + da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1); + return IRQ_HANDLED; +} + +static __init void da830_evm_usb_init(void) +{ + u32 cfgchip2; + int ret; + + /* + * Set up USB clock/mode in the CFGCHIP2 register. + * FYI: CFGCHIP2 is 0x0000ef00 initially. + */ + cfgchip2 = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + + /* USB2.0 PHY reference clock is 24 MHz */ + cfgchip2 &= ~CFGCHIP2_REFFREQ; + cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ; + + /* + * Select internal reference clock for USB 2.0 PHY + * and use it as a clock source for USB 1.1 PHY + * (this is the default setting anyway). + */ + cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX; + cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX; + + /* + * We have to override VBUS/ID signals when MUSB is configured into the + * host-only mode -- ID pin will float if no cable is connected, so the + * controller won't be able to drive VBUS thinking that it's a B-device. + * Otherwise, we want to use the OTG mode and enable VBUS comparators. + */ + cfgchip2 &= ~CFGCHIP2_OTGMODE; +#ifdef CONFIG_USB_MUSB_HOST + cfgchip2 |= CFGCHIP2_FORCE_HOST; +#else + cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN; +#endif + + __raw_writel(cfgchip2, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + + /* USB_REFCLKIN is not used. */ + ret = davinci_cfg_reg(DA830_USB0_DRVVBUS); + if (ret) + pr_warning("%s: USB 2.0 PinMux setup failed: %d\n", + __func__, ret); + else { + /* + * TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A), + * with the power on to power good time of 3 ms. + */ + ret = da8xx_register_usb20(1000, 3); + if (ret) + pr_warning("%s: USB 2.0 registration failed: %d\n", + __func__, ret); + } + + ret = da8xx_pinmux_setup(da830_evm_usb11_pins); + if (ret) { + pr_warning("%s: USB 1.1 PinMux setup failed: %d\n", + __func__, ret); + return; + } + + ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV"); + if (ret) { + printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "power control: %d\n", __func__, ret); + return; + } + gpio_direction_output(ON_BD_USB_DRV, 0); + + ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC"); + if (ret) { + printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "over-current indicator: %d\n", __func__, ret); + return; + } + gpio_direction_input(ON_BD_USB_OVC); + + ret = da8xx_register_usb11(&da830_evm_usb11_pdata); + if (ret) + pr_warning("%s: USB 1.1 registration failed: %d\n", + __func__, ret); +} + static struct davinci_uart_config da830_evm_uart_config __initdata = { .enabled_uarts = 0x7, }; +static const short da830_evm_mcasp1_pins[] = { + DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1, + DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5, + DA830_ACLKR1, DA830_AXR1_6, DA830_AXR1_7, DA830_AXR1_8, DA830_AXR1_10, + DA830_AXR1_11, + -1 +}; + static u8 da830_iis_serializer_direction[] = { RX_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, TX_MODE, INACTIVE_MODE, INACTIVE_MODE, @@ -74,6 +217,271 @@ static struct snd_platform_data da830_evm_snd_data = { .rxnumevt = 1, }; +/* + * GPIO2[1] is used as MMC_SD_WP and GPIO2[2] as MMC_SD_INS. + */ +static const short da830_evm_mmc_sd_pins[] = { + DA830_MMCSD_DAT_0, DA830_MMCSD_DAT_1, DA830_MMCSD_DAT_2, + DA830_MMCSD_DAT_3, DA830_MMCSD_DAT_4, DA830_MMCSD_DAT_5, + DA830_MMCSD_DAT_6, DA830_MMCSD_DAT_7, DA830_MMCSD_CLK, + DA830_MMCSD_CMD, DA830_GPIO2_1, DA830_GPIO2_2, + -1 +}; + +#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1) + +static int da830_evm_mmc_get_ro(int index) +{ + return gpio_get_value(DA830_MMCSD_WP_PIN); +} + +static struct davinci_mmc_config da830_evm_mmc_config = { + .get_ro = da830_evm_mmc_get_ro, + .wires = 4, + .max_freq = 50000000, + .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED, + .version = MMC_CTLR_VERSION_2, +}; + +static inline void da830_evm_init_mmc(void) +{ + int ret; + + ret = da8xx_pinmux_setup(da830_evm_mmc_sd_pins); + if (ret) { + pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n", + ret); + return; + } + + ret = gpio_request(DA830_MMCSD_WP_PIN, "MMC WP"); + if (ret) { + pr_warning("da830_evm_init: can not open GPIO %d\n", + DA830_MMCSD_WP_PIN); + return; + } + gpio_direction_input(DA830_MMCSD_WP_PIN); + + ret = da8xx_register_mmcsd0(&da830_evm_mmc_config); + if (ret) { + pr_warning("da830_evm_init: mmc/sd registration failed: %d\n", + ret); + gpio_free(DA830_MMCSD_WP_PIN); + } +} + +/* + * UI board NAND/NOR flashes only use 8-bit data bus. + */ +static const short da830_evm_emif25_pins[] = { + DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3, + DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7, + DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3, + DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7, + DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11, + DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE, + DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0, + -1 +}; + +#if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE) +#define HAS_MMC 1 +#else +#define HAS_MMC 0 +#endif + +#ifdef CONFIG_DA830_UI_NAND +static struct mtd_partition da830_evm_nand_partitions[] = { + /* bootloader (U-Boot, etc) in first sector */ + [0] = { + .name = "bootloader", + .offset = 0, + .size = SZ_128K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* bootloader params in the next sector */ + [1] = { + .name = "params", + .offset = MTDPART_OFS_APPEND, + .size = SZ_128K, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + /* kernel */ + [2] = { + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_2M, + .mask_flags = 0, + }, + /* file system */ + [3] = { + .name = "filesystem", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + } +}; + +/* flash bbt decriptors */ +static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' }; +static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' }; + +static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | + NAND_BBT_WRITE | NAND_BBT_2BIT | + NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 2, + .len = 4, + .veroffs = 16, + .maxblocks = 4, + .pattern = da830_evm_nand_bbt_pattern +}; + +static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = { + .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | + NAND_BBT_WRITE | NAND_BBT_2BIT | + NAND_BBT_VERSION | NAND_BBT_PERCHIP, + .offs = 2, + .len = 4, + .veroffs = 16, + .maxblocks = 4, + .pattern = da830_evm_nand_mirror_pattern +}; + +static struct davinci_nand_pdata da830_evm_nand_pdata = { + .parts = da830_evm_nand_partitions, + .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions), + .ecc_mode = NAND_ECC_HW, + .ecc_bits = 4, + .options = NAND_USE_FLASH_BBT, + .bbt_td = &da830_evm_nand_bbt_main_descr, + .bbt_md = &da830_evm_nand_bbt_mirror_descr, +}; + +static struct resource da830_evm_nand_resources[] = { + [0] = { /* First memory resource is NAND I/O window */ + .start = DA830_EMIF25_ASYNC_DATA_CE3_BASE, + .end = DA830_EMIF25_ASYNC_DATA_CE3_BASE + PAGE_SIZE - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* Second memory resource is AEMIF control registers */ + .start = DA830_EMIF25_CONTROL_BASE, + .end = DA830_EMIF25_CONTROL_BASE + SZ_32K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device da830_evm_nand_device = { + .name = "davinci_nand", + .id = 1, + .dev = { + .platform_data = &da830_evm_nand_pdata, + }, + .num_resources = ARRAY_SIZE(da830_evm_nand_resources), + .resource = da830_evm_nand_resources, +}; + +static inline void da830_evm_init_nand(int mux_mode) +{ + int ret; + + if (HAS_MMC) { + pr_warning("WARNING: both MMC/SD and NAND are " + "enabled, but they share AEMIF pins.\n" + "\tDisable MMC/SD for NAND support.\n"); + return; + } + + ret = da8xx_pinmux_setup(da830_evm_emif25_pins); + if (ret) + pr_warning("da830_evm_init: emif25 mux setup failed: %d\n", + ret); + + ret = platform_device_register(&da830_evm_nand_device); + if (ret) + pr_warning("da830_evm_init: NAND device not registered.\n"); + + gpio_direction_output(mux_mode, 1); +} +#else +static inline void da830_evm_init_nand(int mux_mode) { } +#endif + +#ifdef CONFIG_DA830_UI_LCD +static inline void da830_evm_init_lcdc(int mux_mode) +{ + int ret; + + ret = da8xx_pinmux_setup(da830_lcdcntl_pins); + if (ret) + pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n", + ret); + + ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata); + if (ret) + pr_warning("da830_evm_init: lcd setup failed: %d\n", ret); + + gpio_direction_output(mux_mode, 0); +} +#else +static inline void da830_evm_init_lcdc(int mux_mode) { } +#endif + +static struct at24_platform_data da830_evm_i2c_eeprom_info = { + .byte_len = SZ_256K / 8, + .page_size = 64, + .flags = AT24_FLAG_ADDR16, + .setup = davinci_get_mac_addr, + .context = (void *)0x7f00, +}; + +static int __init da830_evm_ui_expander_setup(struct i2c_client *client, + int gpio, unsigned ngpio, void *context) +{ + gpio_request(gpio + 6, "UI MUX_MODE"); + + /* Drive mux mode low to match the default without UI card */ + gpio_direction_output(gpio + 6, 0); + + da830_evm_init_lcdc(gpio + 6); + + da830_evm_init_nand(gpio + 6); + + return 0; +} + +static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio, + unsigned ngpio, void *context) +{ + gpio_free(gpio + 6); + return 0; +} + +static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = { + .gpio_base = DAVINCI_N_GPIO, + .setup = da830_evm_ui_expander_setup, + .teardown = da830_evm_ui_expander_teardown, +}; + +static struct i2c_board_info __initdata da830_evm_i2c_devices[] = { + { + I2C_BOARD_INFO("24c256", 0x50), + .platform_data = &da830_evm_i2c_eeprom_info, + }, + { + I2C_BOARD_INFO("tlv320aic3x", 0x18), + }, + { + I2C_BOARD_INFO("pcf8574", 0x3f), + .platform_data = &da830_evm_ui_expander_info, + }, +}; + +static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = { + .bus_freq = 100, /* kHz */ + .bus_delay = 0, /* usec */ +}; + static __init void da830_evm_init(void) { struct davinci_soc_info *soc_info = &davinci_soc_info; @@ -94,6 +502,8 @@ static __init void da830_evm_init(void) pr_warning("da830_evm_init: i2c0 registration failed: %d\n", ret); + da830_evm_usb_init(); + soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK; soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY; soc_info->emac_pdata->rmii_en = 1; @@ -117,12 +527,18 @@ static __init void da830_evm_init(void) i2c_register_board_info(1, da830_evm_i2c_devices, ARRAY_SIZE(da830_evm_i2c_devices)); - ret = da8xx_pinmux_setup(da830_mcasp1_pins); + ret = da8xx_pinmux_setup(da830_evm_mcasp1_pins); if (ret) pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n", ret); - da8xx_init_mcasp(1, &da830_evm_snd_data); + da8xx_register_mcasp(1, &da830_evm_snd_data); + + da830_evm_init_mmc(); + + ret = da8xx_register_rtc(); + if (ret) + pr_warning("da830_evm_init: rtc setup failed: %d\n", ret); } #ifdef CONFIG_SERIAL_8250_CONSOLE @@ -146,7 +562,7 @@ static void __init da830_evm_map_io(void) da830_init(); } -MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP L137 EVM") +MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM") .phys_io = IO_PHYS, .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DA8XX_DDR_BASE + 0x100), diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index c759d72494e..07de8db1458 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -12,36 +12,38 @@ * or implied. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> #include <linux/console.h> #include <linux/i2c.h> #include <linux/i2c/at24.h> +#include <linux/i2c/pca953x.h> #include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> +#include <linux/regulator/machine.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <mach/common.h> -#include <mach/irqs.h> #include <mach/cp_intc.h> #include <mach/da8xx.h> #include <mach/nand.h> +#include <mach/mux.h> #define DA850_EVM_PHY_MASK 0x1 #define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ +#define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8) #define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15) -#define DA850_LCD_PWR_PIN GPIO_TO_PIN(8, 10) #define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0) #define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1) +#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6) + static struct mtd_partition da850_evm_norflash_partition[] = { { .name = "NOR filesystem", @@ -143,10 +145,149 @@ static struct platform_device da850_evm_nandflash_device = { .resource = da850_evm_nandflash_resource, }; +static struct platform_device *da850_evm_devices[] __initdata = { + &da850_evm_nandflash_device, + &da850_evm_norflash_device, +}; + +#define DA8XX_AEMIF_CE2CFG_OFFSET 0x10 +#define DA8XX_AEMIF_ASIZE_16BIT 0x1 + +static void __init da850_evm_init_nor(void) +{ + void __iomem *aemif_addr; + + aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K); + + /* Configure data bus width of CS2 to 16 bit */ + writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) | + DA8XX_AEMIF_ASIZE_16BIT, + aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET); + + iounmap(aemif_addr); +} + +static u32 ui_card_detected; + +#if defined(CONFIG_MMC_DAVINCI) || \ + defined(CONFIG_MMC_DAVINCI_MODULE) +#define HAS_MMC 1 +#else +#define HAS_MMC 0 +#endif + +static __init void da850_evm_setup_nor_nand(void) +{ + int ret = 0; + + if (ui_card_detected & !HAS_MMC) { + ret = da8xx_pinmux_setup(da850_nand_pins); + if (ret) + pr_warning("da850_evm_init: nand mux setup failed: " + "%d\n", ret); + + ret = da8xx_pinmux_setup(da850_nor_pins); + if (ret) + pr_warning("da850_evm_init: nor mux setup failed: %d\n", + ret); + + da850_evm_init_nor(); + + platform_add_devices(da850_evm_devices, + ARRAY_SIZE(da850_evm_devices)); + } +} + +#ifdef CONFIG_DA850_UI_RMII +static inline void da850_evm_setup_emac_rmii(int rmii_sel) +{ + struct davinci_soc_info *soc_info = &davinci_soc_info; + + soc_info->emac_pdata->rmii_en = 1; + gpio_set_value(rmii_sel, 0); +} +#else +static inline void da850_evm_setup_emac_rmii(int rmii_sel) { } +#endif + +static int da850_evm_ui_expander_setup(struct i2c_client *client, unsigned gpio, + unsigned ngpio, void *c) +{ + int sel_a, sel_b, sel_c, ret; + + sel_a = gpio + 7; + sel_b = gpio + 6; + sel_c = gpio + 5; + + ret = gpio_request(sel_a, "sel_a"); + if (ret) { + pr_warning("Cannot open UI expander pin %d\n", sel_a); + goto exp_setup_sela_fail; + } + + ret = gpio_request(sel_b, "sel_b"); + if (ret) { + pr_warning("Cannot open UI expander pin %d\n", sel_b); + goto exp_setup_selb_fail; + } + + ret = gpio_request(sel_c, "sel_c"); + if (ret) { + pr_warning("Cannot open UI expander pin %d\n", sel_c); + goto exp_setup_selc_fail; + } + + /* deselect all functionalities */ + gpio_direction_output(sel_a, 1); + gpio_direction_output(sel_b, 1); + gpio_direction_output(sel_c, 1); + + ui_card_detected = 1; + pr_info("DA850/OMAP-L138 EVM UI card detected\n"); + + da850_evm_setup_nor_nand(); + + da850_evm_setup_emac_rmii(sel_a); + + return 0; + +exp_setup_selc_fail: + gpio_free(sel_b); +exp_setup_selb_fail: + gpio_free(sel_a); +exp_setup_sela_fail: + return ret; +} + +static int da850_evm_ui_expander_teardown(struct i2c_client *client, + unsigned gpio, unsigned ngpio, void *c) +{ + /* deselect all functionalities */ + gpio_set_value(gpio + 5, 1); + gpio_set_value(gpio + 6, 1); + gpio_set_value(gpio + 7, 1); + + gpio_free(gpio + 5); + gpio_free(gpio + 6); + gpio_free(gpio + 7); + + return 0; +} + +static struct pca953x_platform_data da850_evm_ui_expander_info = { + .gpio_base = DAVINCI_N_GPIO, + .setup = da850_evm_ui_expander_setup, + .teardown = da850_evm_ui_expander_teardown, +}; + static struct i2c_board_info __initdata da850_evm_i2c_devices[] = { { I2C_BOARD_INFO("tlv320aic3x", 0x18), - } + }, + { + I2C_BOARD_INFO("tca6416", 0x20), + .platform_data = &da850_evm_ui_expander_info, + }, }; static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = { @@ -158,11 +299,6 @@ static struct davinci_uart_config da850_evm_uart_config __initdata = { .enabled_uarts = 0x7, }; -static struct platform_device *da850_evm_devices[] __initdata = { - &da850_evm_nandflash_device, - &da850_evm_norflash_device, -}; - /* davinci da850 evm audio machine driver */ static u8 da850_iis_serializer_direction[] = { INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, @@ -198,9 +334,20 @@ static struct davinci_mmc_config da850_mmc_config = { .get_ro = da850_evm_mmc_get_ro, .get_cd = da850_evm_mmc_get_cd, .wires = 4, + .max_freq = 50000000, + .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED, .version = MMC_CTLR_VERSION_2, }; +static void da850_panel_power_ctrl(int val) +{ + /* lcd backlight */ + gpio_set_value(DA850_LCD_BL_PIN, val); + + /* lcd power */ + gpio_set_value(DA850_LCD_PWR_PIN, val); +} + static int da850_lcd_hw_init(void) { int status; @@ -218,71 +365,236 @@ static int da850_lcd_hw_init(void) gpio_direction_output(DA850_LCD_BL_PIN, 0); gpio_direction_output(DA850_LCD_PWR_PIN, 0); - /* disable lcd backlight */ - gpio_set_value(DA850_LCD_BL_PIN, 0); - - /* disable lcd power */ - gpio_set_value(DA850_LCD_PWR_PIN, 0); + /* Switch off panel power and backlight */ + da850_panel_power_ctrl(0); - /* enable lcd power */ - gpio_set_value(DA850_LCD_PWR_PIN, 1); - - /* enable lcd backlight */ - gpio_set_value(DA850_LCD_BL_PIN, 1); + /* Switch on panel power and backlight */ + da850_panel_power_ctrl(1); return 0; } -#define DA8XX_AEMIF_CE2CFG_OFFSET 0x10 -#define DA8XX_AEMIF_ASIZE_16BIT 0x1 +/* TPS65070 voltage regulator support */ -static void __init da850_evm_init_nor(void) -{ - void __iomem *aemif_addr; +/* 3.3V */ +struct regulator_consumer_supply tps65070_dcdc1_consumers[] = { + { + .supply = "usb0_vdda33", + }, + { + .supply = "usb1_vdda33", + }, +}; - aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K); +/* 3.3V or 1.8V */ +struct regulator_consumer_supply tps65070_dcdc2_consumers[] = { + { + .supply = "dvdd3318_a", + }, + { + .supply = "dvdd3318_b", + }, + { + .supply = "dvdd3318_c", + }, +}; - /* Configure data bus width of CS2 to 16 bit */ - writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) | - DA8XX_AEMIF_ASIZE_16BIT, - aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET); +/* 1.2V */ +struct regulator_consumer_supply tps65070_dcdc3_consumers[] = { + { + .supply = "cvdd", + }, +}; - iounmap(aemif_addr); -} +/* 1.8V LDO */ +struct regulator_consumer_supply tps65070_ldo1_consumers[] = { + { + .supply = "sata_vddr", + }, + { + .supply = "usb0_vdda18", + }, + { + .supply = "usb1_vdda18", + }, + { + .supply = "ddr_dvdd18", + }, +}; -#if defined(CONFIG_MTD_PHYSMAP) || \ - defined(CONFIG_MTD_PHYSMAP_MODULE) -#define HAS_NOR 1 -#else -#define HAS_NOR 0 -#endif +/* 1.2V LDO */ +struct regulator_consumer_supply tps65070_ldo2_consumers[] = { + { + .supply = "sata_vdd", + }, + { + .supply = "pll0_vdda", + }, + { + .supply = "pll1_vdda", + }, + { + .supply = "usbs_cvdd", + }, + { + .supply = "vddarnwa1", + }, +}; -#if defined(CONFIG_MMC_DAVINCI) || \ - defined(CONFIG_MMC_DAVINCI_MODULE) -#define HAS_MMC 1 -#else -#define HAS_MMC 0 -#endif +struct regulator_init_data tps65070_regulator_data[] = { + /* dcdc1 */ + { + .constraints = { + .min_uV = 3150000, + .max_uV = 3450000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS), + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc1_consumers), + .consumer_supplies = tps65070_dcdc1_consumers, + }, -static __init void da850_evm_init(void) + /* dcdc2 */ + { + .constraints = { + .min_uV = 1710000, + .max_uV = 3450000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS), + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc2_consumers), + .consumer_supplies = tps65070_dcdc2_consumers, + }, + + /* dcdc3 */ + { + .constraints = { + .min_uV = 950000, + .max_uV = 1320000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS), + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc3_consumers), + .consumer_supplies = tps65070_dcdc3_consumers, + }, + + /* ldo1 */ + { + .constraints = { + .min_uV = 1710000, + .max_uV = 1890000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS), + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65070_ldo1_consumers), + .consumer_supplies = tps65070_ldo1_consumers, + }, + + /* ldo2 */ + { + .constraints = { + .min_uV = 1140000, + .max_uV = 1320000, + .valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS), + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65070_ldo2_consumers), + .consumer_supplies = tps65070_ldo2_consumers, + }, +}; + +static struct i2c_board_info __initdata da850evm_tps65070_info[] = { + { + I2C_BOARD_INFO("tps6507x", 0x48), + .platform_data = &tps65070_regulator_data[0], + }, +}; + +static int __init pmic_tps65070_init(void) { - struct davinci_soc_info *soc_info = &davinci_soc_info; + return i2c_register_board_info(1, da850evm_tps65070_info, + ARRAY_SIZE(da850evm_tps65070_info)); +} + +static const short da850_evm_lcdc_pins[] = { + DA850_GPIO2_8, DA850_GPIO2_15, + -1 +}; + +static int __init da850_evm_config_emac(void) +{ + void __iomem *cfg_chip3_base; int ret; + u32 val; + struct davinci_soc_info *soc_info = &davinci_soc_info; + u8 rmii_en = soc_info->emac_pdata->rmii_en; + + if (!machine_is_davinci_da850_evm()) + return 0; + + cfg_chip3_base = DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG); + + val = __raw_readl(cfg_chip3_base); + + if (rmii_en) { + val |= BIT(8); + ret = da8xx_pinmux_setup(da850_rmii_pins); + pr_info("EMAC: RMII PHY configured, MII PHY will not be" + " functional\n"); + } else { + val &= ~BIT(8); + ret = da8xx_pinmux_setup(da850_cpgmac_pins); + pr_info("EMAC: MII PHY configured, RMII PHY will not be" + " functional\n"); + } - ret = da8xx_pinmux_setup(da850_nand_pins); if (ret) - pr_warning("da850_evm_init: nand mux setup failed: %d\n", + pr_warning("da850_evm_init: cpgmac/rmii mux setup failed: %d\n", ret); - ret = da8xx_pinmux_setup(da850_nor_pins); + /* configure the CFGCHIP3 register for RMII or MII */ + __raw_writel(val, cfg_chip3_base); + + ret = davinci_cfg_reg(DA850_GPIO2_6); if (ret) - pr_warning("da850_evm_init: nor mux setup failed: %d\n", + pr_warning("da850_evm_init:GPIO(2,6) mux setup " + "failed\n"); + + ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en"); + if (ret) { + pr_warning("Cannot open GPIO %d\n", + DA850_MII_MDIO_CLKEN_PIN); + return ret; + } + + /* Enable/Disable MII MDIO clock */ + gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en); + + soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK; + soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY; + + ret = da8xx_register_emac(); + if (ret) + pr_warning("da850_evm_init: emac registration failed: %d\n", ret); - da850_evm_init_nor(); + return 0; +} +device_initcall(da850_evm_config_emac); - platform_add_devices(da850_evm_devices, - ARRAY_SIZE(da850_evm_devices)); +static __init void da850_evm_init(void) +{ + int ret; + + ret = pmic_tps65070_init(); + if (ret) + pr_warning("da850_evm_init: TPS65070 PMIC init failed: %d\n", + ret); ret = da8xx_register_edma(); if (ret) @@ -299,19 +611,6 @@ static __init void da850_evm_init(void) pr_warning("da850_evm_init: i2c0 registration failed: %d\n", ret); - soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY; - soc_info->emac_pdata->rmii_en = 0; - - ret = da8xx_pinmux_setup(da850_cpgmac_pins); - if (ret) - pr_warning("da850_evm_init: cpgmac mux setup failed: %d\n", - ret); - - ret = da8xx_register_emac(); - if (ret) - pr_warning("da850_evm_init: emac registration failed: %d\n", - ret); ret = da8xx_register_watchdog(); if (ret) @@ -319,11 +618,6 @@ static __init void da850_evm_init(void) ret); if (HAS_MMC) { - if (HAS_NOR) - pr_warning("WARNING: both NOR Flash and MMC/SD are " - "enabled, but they share AEMIF pins.\n" - "\tDisable one of them.\n"); - ret = da8xx_pinmux_setup(da850_mmcsd0_pins); if (ret) pr_warning("da850_evm_init: mmcsd0 mux setup failed:" @@ -365,22 +659,43 @@ static __init void da850_evm_init(void) pr_warning("da850_evm_init: mcasp mux setup failed: %d\n", ret); - da8xx_init_mcasp(0, &da850_evm_snd_data); + da8xx_register_mcasp(0, &da850_evm_snd_data); ret = da8xx_pinmux_setup(da850_lcdcntl_pins); if (ret) pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", ret); + /* Handle board specific muxing for LCD here */ + ret = da8xx_pinmux_setup(da850_evm_lcdc_pins); + if (ret) + pr_warning("da850_evm_init: evm specific lcd mux setup " + "failed: %d\n", ret); + ret = da850_lcd_hw_init(); if (ret) pr_warning("da850_evm_init: lcd initialization failed: %d\n", ret); - ret = da8xx_register_lcdc(); + sharp_lk043t1dg01_pdata.panel_power_ctrl = da850_panel_power_ctrl, + ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata); if (ret) pr_warning("da850_evm_init: lcdc registration failed: %d\n", ret); + + ret = da8xx_register_rtc(); + if (ret) + pr_warning("da850_evm_init: rtc setup failed: %d\n", ret); + + ret = da850_register_cpufreq(); + if (ret) + pr_warning("da850_evm_init: cpufreq registration failed: %d\n", + ret); + + ret = da8xx_register_cpuidle(); + if (ret) + pr_warning("da850_evm_init: cpuidle registration failed: %d\n", + ret); } #ifdef CONFIG_SERIAL_8250_CONSOLE diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index 77e80679882..a9b650dcc17 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -9,15 +9,13 @@ * or implied. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> -#include <linux/dma-mapping.h> +#include <linux/err.h> #include <linux/platform_device.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> #include <linux/i2c.h> -#include <linux/io.h> #include <linux/gpio.h> #include <linux/clk.h> #include <linux/videodev2.h> @@ -25,20 +23,15 @@ #include <linux/spi/spi.h> #include <linux/spi/eeprom.h> -#include <asm/setup.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/flash.h> -#include <mach/hardware.h> #include <mach/dm355.h> -#include <mach/psc.h> -#include <mach/common.h> #include <mach/i2c.h> #include <mach/serial.h> #include <mach/nand.h> #include <mach/mmc.h> +#include <mach/usb.h> #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 @@ -86,8 +79,9 @@ static struct davinci_nand_pdata davinci_nand_data = { .mask_chipsel = BIT(14), .parts = davinci_nand_partitions, .nr_parts = ARRAY_SIZE(davinci_nand_partitions), - .ecc_mode = NAND_ECC_HW_SYNDROME, + .ecc_mode = NAND_ECC_HW, .options = NAND_USE_FLASH_BBT, + .ecc_bits = 4, }; static struct resource davinci_nand_resources[] = { @@ -344,7 +338,7 @@ static __init void dm355_evm_init(void) gpio_request(2, "usb_id_toggle"); gpio_direction_output(2, USB_ID_VALUE); /* irlml6401 switches over 1A in under 8 msec */ - setup_usb(500, 8); + davinci_setup_usb(1000, 8); davinci_setup_mmc(0, &dm355evm_mmc_config); davinci_setup_mmc(1, &dm355evm_mmc_config); diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index 84ad5d161a8..21f32eb41e8 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -8,34 +8,27 @@ * warranty of any kind, whether express or implied. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> -#include <linux/dma-mapping.h> +#include <linux/err.h> #include <linux/platform_device.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> #include <linux/i2c.h> -#include <linux/io.h> #include <linux/gpio.h> #include <linux/clk.h> #include <linux/spi/spi.h> #include <linux/spi/eeprom.h> -#include <asm/setup.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/flash.h> -#include <mach/hardware.h> #include <mach/dm355.h> -#include <mach/psc.h> -#include <mach/common.h> #include <mach/i2c.h> #include <mach/serial.h> #include <mach/nand.h> #include <mach/mmc.h> +#include <mach/usb.h> #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 @@ -270,7 +263,7 @@ static __init void dm355_leopard_init(void) gpio_request(2, "usb_id_toggle"); gpio_direction_output(2, USB_ID_VALUE); /* irlml6401 switches over 1A in under 8 msec */ - setup_usb(500, 8); + davinci_setup_usb(1000, 8); davinci_setup_mmc(0, &dm355leopard_mmc_config); davinci_setup_mmc(1, &dm355leopard_mmc_config); diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index a1d5e7dac74..289fe1b7d25 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -13,9 +13,8 @@ * GNU General Public License for more details. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> -#include <linux/dma-mapping.h> +#include <linux/err.h> #include <linux/i2c.h> #include <linux/io.h> #include <linux/clk.h> @@ -24,21 +23,19 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/mtd/nand.h> -#include <asm/setup.h> +#include <linux/input.h> + #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/mach/map.h> + #include <mach/mux.h> -#include <mach/hardware.h> #include <mach/dm365.h> -#include <mach/psc.h> #include <mach/common.h> #include <mach/i2c.h> #include <mach/serial.h> -#include <mach/common.h> #include <mach/mmc.h> #include <mach/nand.h> - +#include <mach/keyscan.h> static inline int have_imager(void) { @@ -145,6 +142,7 @@ static struct davinci_nand_pdata davinci_nand_data = { .nr_parts = ARRAY_SIZE(davinci_nand_partitions), .ecc_mode = NAND_ECC_HW, .options = NAND_USE_FLASH_BBT, + .ecc_bits = 4, }; static struct resource davinci_nand_resources[] = { @@ -177,11 +175,16 @@ static struct at24_platform_data eeprom_info = { .context = (void *)0x7f00, }; +static struct snd_platform_data dm365_evm_snd_data; + static struct i2c_board_info i2c_info[] = { { I2C_BOARD_INFO("24c256", 0x50), .platform_data = &eeprom_info, }, + { + I2C_BOARD_INFO("tlv320aic3x", 0x18), + }, }; static struct davinci_i2c_platform_data i2c_pdata = { @@ -189,6 +192,38 @@ static struct davinci_i2c_platform_data i2c_pdata = { .bus_delay = 0 /* usec */, }; +#ifdef CONFIG_KEYBOARD_DAVINCI +static unsigned short dm365evm_keymap[] = { + KEY_KP2, + KEY_LEFT, + KEY_EXIT, + KEY_DOWN, + KEY_ENTER, + KEY_UP, + KEY_KP1, + KEY_RIGHT, + KEY_MENU, + KEY_RECORD, + KEY_REWIND, + KEY_KPMINUS, + KEY_STOP, + KEY_FASTFORWARD, + KEY_KPPLUS, + KEY_PLAYPAUSE, + 0 +}; + +static struct davinci_ks_platform_data dm365evm_ks_data = { + .keymap = dm365evm_keymap, + .keymapsize = ARRAY_SIZE(dm365evm_keymap), + .rep = 1, + /* Scan period = strobe + interval */ + .strobe = 0x5, + .interval = 0x2, + .matrix_type = DAVINCI_KEYSCAN_MATRIX_4X4, +}; +#endif + static int cpld_mmc_get_cd(int module) { if (!cpld) @@ -473,6 +508,13 @@ static __init void dm365_evm_init(void) /* maybe setup mmc1/etc ... _after_ mmc0 */ evm_init_cpld(); + + dm365_init_asp(&dm365_evm_snd_data); + dm365_init_rtc(); + +#ifdef CONFIG_KEYBOARD_DAVINCI + dm365_init_ks(&dm365evm_ks_data); +#endif } static __init void dm365_evm_irq_init(void) diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 1213a0087ad..fd0398bc6db 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -9,45 +9,34 @@ * or implied. */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> #include <linux/dma-mapping.h> #include <linux/platform_device.h> #include <linux/gpio.h> -#include <linux/leds.h> -#include <linux/memory.h> - #include <linux/i2c.h> #include <linux/i2c/pcf857x.h> #include <linux/i2c/at24.h> -#include <linux/etherdevice.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> #include <linux/mtd/physmap.h> -#include <linux/io.h> #include <linux/phy.h> #include <linux/clk.h> #include <linux/videodev2.h> #include <media/tvp514x.h> -#include <asm/setup.h> #include <asm/mach-types.h> - #include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/flash.h> #include <mach/dm644x.h> #include <mach/common.h> #include <mach/i2c.h> #include <mach/serial.h> #include <mach/mux.h> -#include <mach/psc.h> #include <mach/nand.h> #include <mach/mmc.h> -#include <mach/emac.h> +#include <mach/usb.h> #define DM644X_EVM_PHY_MASK (0x2) #define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ @@ -477,7 +466,7 @@ evm_u35_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c) /* irlml6401 switches over 1A, in under 8 msec; * now it can be managed by nDRV_VBUS ... */ - setup_usb(500, 8); + davinci_setup_usb(1000, 8); return 0; } diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index 24e0e13b149..8d0b0e01c59 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -17,38 +17,28 @@ **************************************************************************/ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> -#include <linux/fs.h> -#include <linux/major.h> -#include <linux/root_dev.h> -#include <linux/dma-mapping.h> -#include <linux/serial.h> -#include <linux/serial_8250.h> #include <linux/leds.h> #include <linux/gpio.h> -#include <linux/io.h> #include <linux/platform_device.h> #include <linux/i2c.h> #include <linux/i2c/at24.h> #include <linux/i2c/pcf857x.h> -#include <linux/etherdevice.h> #include <media/tvp514x.h> -#include <asm/setup.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/mtd/partitions.h> + #include <asm/mach-types.h> #include <asm/mach/arch.h> -#include <asm/mach/map.h> -#include <asm/mach/flash.h> #include <mach/dm646x.h> #include <mach/common.h> -#include <mach/psc.h> #include <mach/serial.h> #include <mach/i2c.h> -#include <mach/mmc.h> -#include <mach/emac.h> +#include <mach/nand.h> #if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \ defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE) @@ -57,6 +47,11 @@ #define HAS_ATA 0 #endif +#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x20008000 +#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x42000000 + +#define NAND_BLOCK_SIZE SZ_128K + /* CPLD Register 0 bits to control ATA */ #define DM646X_EVM_ATA_RST BIT(0) #define DM646X_EVM_ATA_PWD BIT(1) @@ -92,6 +87,63 @@ static struct davinci_uart_config uart_config __initdata = { .enabled_uarts = (1 << 0), }; +/* Note: We are setting first partition as 'bootloader' constituting UBL, U-Boot + * and U-Boot environment this avoids dependency on any particular combination + * of UBL, U-Boot or flashing tools etc. + */ +static struct mtd_partition davinci_nand_partitions[] = { + { + /* UBL, U-Boot with environment */ + .name = "bootloader", + .offset = MTDPART_OFS_APPEND, + .size = 16 * NAND_BLOCK_SIZE, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_4M, + .mask_flags = 0, + }, { + .name = "filesystem", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + } +}; + +static struct davinci_nand_pdata davinci_nand_data = { + .mask_cle = 0x80000, + .mask_ale = 0x40000, + .parts = davinci_nand_partitions, + .nr_parts = ARRAY_SIZE(davinci_nand_partitions), + .ecc_mode = NAND_ECC_HW, + .options = 0, +}; + +static struct resource davinci_nand_resources[] = { + { + .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE, + .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1, + .flags = IORESOURCE_MEM, + }, { + .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE, + .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device davinci_nand_device = { + .name = "davinci_nand", + .id = 0, + + .num_resources = ARRAY_SIZE(davinci_nand_resources), + .resource = davinci_nand_resources, + + .dev = { + .platform_data = &davinci_nand_data, + }, +}; + /* CPLD Register 0 Client: used for I/O Control */ static int cpld_reg0_probe(struct i2c_client *client, const struct i2c_device_id *id) @@ -142,7 +194,7 @@ static struct gpio_led evm_leds[] = { { .name = "DS4", .active_low = 1, }, }; -static __initconst struct gpio_led_platform_data evm_led_data = { +static const struct gpio_led_platform_data evm_led_data = { .num_leds = ARRAY_SIZE(evm_leds), .leds = evm_leds, }; @@ -647,6 +699,8 @@ static __init void evm_init(void) dm646x_init_mcasp0(&dm646x_evm_snd_data[0]); dm646x_init_mcasp1(&dm646x_evm_snd_data[1]); + platform_device_register(&davinci_nand_device); + if (HAS_ATA) dm646x_init_ide(); diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c new file mode 100644 index 00000000000..bd9ca079b69 --- /dev/null +++ b/arch/arm/mach-davinci/board-neuros-osd2.c @@ -0,0 +1,323 @@ +/* + * Neuros Technologies OSD2 board support + * + * Modified from original 644X-EVM board support. + * 2008 (c) Neuros Technology, LLC. + * 2009 (c) Jorge Luis Zapata Muga <jorgeluis.zapata@gmail.com> + * 2009 (c) Andrey A. Porodko <Andrey.Porodko@gmail.com> + * + * The Neuros OSD 2.0 is the hardware component of the Neuros Open + * Internet Television Platform. Hardware is very close to TI + * DM644X-EVM board. It has: + * DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC, + * USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video. + * Additionaly realtime clock, IR remote control receiver, + * IR Blaster based on MSP430 (firmware although is different + * from used in DM644X-EVM), internal ATA-6 3.5” HDD drive + * with PATA interface, two muxed red-green leds. + * + * For more information please refer to + * http://wiki.neurostechnology.com/index.php/OSD_2.0_HD + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/mtd/partitions.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/dm644x.h> +#include <mach/i2c.h> +#include <mach/serial.h> +#include <mach/mux.h> +#include <mach/nand.h> +#include <mach/mmc.h> +#include <mach/usb.h> + +#define NEUROS_OSD2_PHY_MASK 0x2 +#define NEUROS_OSD2_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ + +#define DAVINCI_CFC_ATA_BASE 0x01C66000 + +#define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e00000 +#define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000 + +#define LXT971_PHY_ID 0x001378e2 +#define LXT971_PHY_MASK 0xfffffff0 + +#define NTOSD2_AUDIOSOC_I2C_ADDR 0x18 +#define NTOSD2_MSP430_I2C_ADDR 0x59 +#define NTOSD2_MSP430_IRQ 2 + +/* Neuros OSD2 has a Samsung 256 MByte NAND flash (Dev ID of 0xAA, + * 2048 blocks in the device, 64 pages per block, 2048 bytes per + * page. + */ + +#define NAND_BLOCK_SIZE SZ_128K + +struct mtd_partition davinci_ntosd2_nandflash_partition[] = { + { + /* UBL (a few copies) plus U-Boot */ + .name = "bootloader", + .offset = 0, + .size = 15 * NAND_BLOCK_SIZE, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { + /* U-Boot environment */ + .name = "params", + .offset = MTDPART_OFS_APPEND, + .size = 1 * NAND_BLOCK_SIZE, + .mask_flags = 0, + }, { + /* Kernel */ + .name = "kernel", + .offset = MTDPART_OFS_APPEND, + .size = SZ_4M, + .mask_flags = 0, + }, { + /* File System */ + .name = "filesystem", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + } + /* A few blocks at end hold a flash Bad Block Table. */ +}; + +static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = { + .parts = davinci_ntosd2_nandflash_partition, + .nr_parts = ARRAY_SIZE(davinci_ntosd2_nandflash_partition), + .ecc_mode = NAND_ECC_HW, + .options = NAND_USE_FLASH_BBT, +}; + +static struct resource davinci_ntosd2_nandflash_resource[] = { + { + .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE, + .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1, + .flags = IORESOURCE_MEM, + }, { + .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE, + .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device davinci_ntosd2_nandflash_device = { + .name = "davinci_nand", + .id = 0, + .dev = { + .platform_data = &davinci_ntosd2_nandflash_data, + }, + .num_resources = ARRAY_SIZE(davinci_ntosd2_nandflash_resource), + .resource = davinci_ntosd2_nandflash_resource, +}; + +static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32); + +static struct platform_device davinci_fb_device = { + .name = "davincifb", + .id = -1, + .dev = { + .dma_mask = &davinci_fb_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = 0, +}; + +static struct resource ide_resources[] = { + { + .start = DAVINCI_CFC_ATA_BASE, + .end = DAVINCI_CFC_ATA_BASE + 0x7ff, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_IDE, + .end = IRQ_IDE, + .flags = IORESOURCE_IRQ, + }, +}; + +static u64 ide_dma_mask = DMA_BIT_MASK(32); + +static struct platform_device ide_dev = { + .name = "palm_bk3710", + .id = -1, + .resource = ide_resources, + .num_resources = ARRAY_SIZE(ide_resources), + .dev = { + .dma_mask = &ide_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, +}; + +static struct snd_platform_data dm644x_ntosd2_snd_data; + +static struct gpio_led ntosd2_leds[] = { + { .name = "led1_green", .gpio = GPIO(10), }, + { .name = "led1_red", .gpio = GPIO(11), }, + { .name = "led2_green", .gpio = GPIO(12), }, + { .name = "led2_red", .gpio = GPIO(13), }, +}; + +static struct gpio_led_platform_data ntosd2_leds_data = { + .num_leds = ARRAY_SIZE(ntosd2_leds), + .leds = ntosd2_leds, +}; + +static struct platform_device ntosd2_leds_dev = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &ntosd2_leds_data, + }, +}; + + +static struct platform_device *davinci_ntosd2_devices[] __initdata = { + &davinci_fb_device, + &ntosd2_leds_dev, +}; + +static struct davinci_uart_config uart_config __initdata = { + .enabled_uarts = (1 << 0), +}; + +static void __init davinci_ntosd2_map_io(void) +{ + dm644x_init(); +} + +/* + I2C initialization +*/ +static struct davinci_i2c_platform_data ntosd2_i2c_pdata = { + .bus_freq = 20 /* kHz */, + .bus_delay = 100 /* usec */, +}; + +static struct i2c_board_info __initdata ntosd2_i2c_info[] = { +}; + +static int ntosd2_init_i2c(void) +{ + int status; + + davinci_init_i2c(&ntosd2_i2c_pdata); + status = gpio_request(NTOSD2_MSP430_IRQ, ntosd2_i2c_info[0].type); + if (status == 0) { + status = gpio_direction_input(NTOSD2_MSP430_IRQ); + if (status == 0) { + status = gpio_to_irq(NTOSD2_MSP430_IRQ); + if (status > 0) { + ntosd2_i2c_info[0].irq = status; + i2c_register_board_info(1, + ntosd2_i2c_info, + ARRAY_SIZE(ntosd2_i2c_info)); + } + } + } + return status; +} + +static struct davinci_mmc_config davinci_ntosd2_mmc_config = { + .wires = 4, + .version = MMC_CTLR_VERSION_1 +}; + + +#if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \ + defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE) +#define HAS_ATA 1 +#else +#define HAS_ATA 0 +#endif + +#if defined(CONFIG_MTD_NAND_DAVINCI) || \ + defined(CONFIG_MTD_NAND_DAVINCI_MODULE) +#define HAS_NAND 1 +#else +#define HAS_NAND 0 +#endif + +static __init void davinci_ntosd2_init(void) +{ + struct clk *aemif_clk; + struct davinci_soc_info *soc_info = &davinci_soc_info; + int status; + + aemif_clk = clk_get(NULL, "aemif"); + clk_enable(aemif_clk); + + if (HAS_ATA) { + if (HAS_NAND) + pr_warning("WARNING: both IDE and Flash are " + "enabled, but they share AEMIF pins.\n" + "\tDisable IDE for NAND/NOR support.\n"); + davinci_cfg_reg(DM644X_HPIEN_DISABLE); + davinci_cfg_reg(DM644X_ATAEN); + davinci_cfg_reg(DM644X_HDIREN); + platform_device_register(&ide_dev); + } else if (HAS_NAND) { + davinci_cfg_reg(DM644X_HPIEN_DISABLE); + davinci_cfg_reg(DM644X_ATAEN_DISABLE); + + /* only one device will be jumpered and detected */ + if (HAS_NAND) + platform_device_register( + &davinci_ntosd2_nandflash_device); + } + + platform_add_devices(davinci_ntosd2_devices, + ARRAY_SIZE(davinci_ntosd2_devices)); + + /* Initialize I2C interface specific for this board */ + status = ntosd2_init_i2c(); + if (status < 0) + pr_warning("davinci_ntosd2_init: msp430 irq setup failed:" + " %d\n", status); + + davinci_serial_init(&uart_config); + dm644x_init_asp(&dm644x_ntosd2_snd_data); + + soc_info->emac_pdata->phy_mask = NEUROS_OSD2_PHY_MASK; + soc_info->emac_pdata->mdio_max_freq = NEUROS_OSD2_MDIO_FREQUENCY; + + davinci_setup_usb(1000, 8); + /* + * Mux the pins to be GPIOs, VLYNQEN is already done at startup. + * The AEAWx are five new AEAW pins that can be muxed by separately. + * They are a bitmask for GPIO management. According TI + * documentation (http://www.ti.com/lit/gpn/tms320dm6446) to employ + * gpio(10,11,12,13) for leds any combination of bits works except + * four last. So we are to reset all five. + */ + davinci_cfg_reg(DM644X_AEAW0); + davinci_cfg_reg(DM644X_AEAW1); + davinci_cfg_reg(DM644X_AEAW2); + davinci_cfg_reg(DM644X_AEAW3); + davinci_cfg_reg(DM644X_AEAW4); + + davinci_setup_mmc(0, &davinci_ntosd2_mmc_config); +} + +static __init void davinci_ntosd2_irq_init(void) +{ + davinci_irq_init(); +} + +MACHINE_START(NEUROS_OSD2, "Neuros OSD2") + /* Maintainer: Neuros Technologies <neuros@groups.google.com> */ + .phys_io = IO_PHYS, + .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, + .boot_params = (DAVINCI_DDR_BASE + 0x100), + .map_io = davinci_ntosd2_map_io, + .init_irq = davinci_ntosd2_irq_init, + .timer = &davinci_timer, + .init_machine = davinci_ntosd2_init, +MACHINE_END diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 7acdfd8ac07..08d373bfcc8 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -23,35 +23,24 @@ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -#include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> -#include <linux/dma-mapping.h> #include <linux/platform_device.h> -#include <linux/gpio.h> - #include <linux/i2c.h> #include <linux/i2c/at24.h> -#include <linux/etherdevice.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> -#include <linux/mtd/physmap.h> -#include <linux/io.h> -#include <asm/setup.h> #include <asm/mach-types.h> - #include <asm/mach/arch.h> -#include <asm/mach/map.h> #include <asm/mach/flash.h> #include <mach/dm644x.h> #include <mach/common.h> #include <mach/i2c.h> #include <mach/serial.h> -#include <mach/psc.h> #include <mach/mux.h> +#include <mach/usb.h> #define SFFSDR_PHY_MASK (0x2) #define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ @@ -107,11 +96,6 @@ static struct platform_device davinci_sffsdr_nandflash_device = { .resource = davinci_sffsdr_nandflash_resource, }; -static struct emac_platform_data sffsdr_emac_pdata = { - .phy_mask = SFFSDR_PHY_MASK, - .mdio_max_freq = SFFSDR_MDIO_FREQUENCY, -}; - static struct at24_platform_data eeprom_info = { .byte_len = (64*1024) / 8, .page_size = 32, @@ -164,7 +148,7 @@ static __init void davinci_sffsdr_init(void) davinci_serial_init(&uart_config); soc_info->emac_pdata->phy_mask = SFFSDR_PHY_MASK; soc_info->emac_pdata->mdio_max_freq = SFFSDR_MDIO_FREQUENCY; - setup_usb(0, 0); /* We support only peripheral mode. */ + davinci_setup_usb(0, 0); /* We support only peripheral mode. */ /* mux VLYNQ pins */ davinci_cfg_reg(DM644X_VLYNQEN); diff --git a/arch/arm/mach-davinci/clock.c b/arch/arm/mach-davinci/clock.c index 83d54d50b5e..baece65cb9c 100644 --- a/arch/arm/mach-davinci/clock.c +++ b/arch/arm/mach-davinci/clock.c @@ -17,8 +17,8 @@ #include <linux/clk.h> #include <linux/err.h> #include <linux/mutex.h> -#include <linux/platform_device.h> #include <linux/io.h> +#include <linux/delay.h> #include <mach/hardware.h> @@ -42,8 +42,7 @@ static void __clk_enable(struct clk *clk) if (clk->parent) __clk_enable(clk->parent); if (clk->usecount++ == 0 && (clk->flags & CLK_PSC)) - davinci_psc_config(psc_domain(clk), clk->psc_ctlr, - clk->lpsc, 1); + davinci_psc_config(psc_domain(clk), clk->gpsc, clk->lpsc, 1); } static void __clk_disable(struct clk *clk) @@ -51,8 +50,7 @@ static void __clk_disable(struct clk *clk) if (WARN_ON(clk->usecount == 0)) return; if (--clk->usecount == 0 && !(clk->flags & CLK_PLL)) - davinci_psc_config(psc_domain(clk), clk->psc_ctlr, - clk->lpsc, 0); + davinci_psc_config(psc_domain(clk), clk->gpsc, clk->lpsc, 0); if (clk->parent) __clk_disable(clk->parent); } @@ -99,20 +97,74 @@ long clk_round_rate(struct clk *clk, unsigned long rate) if (clk == NULL || IS_ERR(clk)) return -EINVAL; + if (clk->round_rate) + return clk->round_rate(clk, rate); + return clk->rate; } EXPORT_SYMBOL(clk_round_rate); +/* Propagate rate to children */ +static void propagate_rate(struct clk *root) +{ + struct clk *clk; + + list_for_each_entry(clk, &root->children, childnode) { + if (clk->recalc) + clk->rate = clk->recalc(clk); + propagate_rate(clk); + } +} + int clk_set_rate(struct clk *clk, unsigned long rate) { + unsigned long flags; + int ret = -EINVAL; + if (clk == NULL || IS_ERR(clk)) - return -EINVAL; + return ret; - /* changing the clk rate is not supported */ - return -EINVAL; + spin_lock_irqsave(&clockfw_lock, flags); + if (clk->set_rate) + ret = clk->set_rate(clk, rate); + if (ret == 0) { + if (clk->recalc) + clk->rate = clk->recalc(clk); + propagate_rate(clk); + } + spin_unlock_irqrestore(&clockfw_lock, flags); + + return ret; } EXPORT_SYMBOL(clk_set_rate); +int clk_set_parent(struct clk *clk, struct clk *parent) +{ + unsigned long flags; + + if (clk == NULL || IS_ERR(clk)) + return -EINVAL; + + /* Cannot change parent on enabled clock */ + if (WARN_ON(clk->usecount)) + return -EINVAL; + + mutex_lock(&clocks_mutex); + clk->parent = parent; + list_del_init(&clk->childnode); + list_add(&clk->childnode, &clk->parent->children); + mutex_unlock(&clocks_mutex); + + spin_lock_irqsave(&clockfw_lock, flags); + if (clk->recalc) + clk->rate = clk->recalc(clk); + propagate_rate(clk); + spin_unlock_irqrestore(&clockfw_lock, flags); + + return 0; +} +EXPORT_SYMBOL(clk_set_parent); + int clk_register(struct clk *clk) { if (clk == NULL || IS_ERR(clk)) @@ -123,16 +175,24 @@ int clk_register(struct clk *clk) clk->name, clk->parent->name)) return -EINVAL; + INIT_LIST_HEAD(&clk->children); + mutex_lock(&clocks_mutex); list_add_tail(&clk->node, &clocks); + if (clk->parent) + list_add_tail(&clk->childnode, &clk->parent->children); mutex_unlock(&clocks_mutex); /* If rate is already set, use it */ if (clk->rate) return 0; + /* Else, see if there is a way to calculate it */ + if (clk->recalc) + clk->rate = clk->recalc(clk); + /* Otherwise, default to parent rate */ - if (clk->parent) + else if (clk->parent) clk->rate = clk->parent->rate; return 0; @@ -146,6 +206,7 @@ void clk_unregister(struct clk *clk) mutex_lock(&clocks_mutex); list_del(&clk->node); + list_del(&clk->childnode); mutex_unlock(&clocks_mutex); } EXPORT_SYMBOL(clk_unregister); @@ -166,11 +227,11 @@ static int __init clk_disable_unused(void) continue; /* ignore if in Disabled or SwRstDisable states */ - if (!davinci_psc_is_clk_active(ck->psc_ctlr, ck->lpsc)) + if (!davinci_psc_is_clk_active(ck->gpsc, ck->lpsc)) continue; pr_info("Clocks: disable unused %s\n", ck->name); - davinci_psc_config(psc_domain(ck), ck->psc_ctlr, ck->lpsc, 0); + davinci_psc_config(psc_domain(ck), ck->gpsc, ck->lpsc, 0); } spin_unlock_irq(&clockfw_lock); @@ -179,50 +240,62 @@ static int __init clk_disable_unused(void) late_initcall(clk_disable_unused); #endif -static void clk_sysclk_recalc(struct clk *clk) +static unsigned long clk_sysclk_recalc(struct clk *clk) { u32 v, plldiv; struct pll_data *pll; + unsigned long rate = clk->rate; /* If this is the PLL base clock, no more calculations needed */ if (clk->pll_data) - return; + return rate; if (WARN_ON(!clk->parent)) - return; + return rate; - clk->rate = clk->parent->rate; + rate = clk->parent->rate; /* Otherwise, the parent must be a PLL */ if (WARN_ON(!clk->parent->pll_data)) - return; + return rate; pll = clk->parent->pll_data; /* If pre-PLL, source clock is before the multiplier and divider(s) */ if (clk->flags & PRE_PLL) - clk->rate = pll->input_rate; + rate = pll->input_rate; if (!clk->div_reg) - return; + return rate; v = __raw_readl(pll->base + clk->div_reg); if (v & PLLDIV_EN) { plldiv = (v & PLLDIV_RATIO_MASK) + 1; if (plldiv) - clk->rate /= plldiv; + rate /= plldiv; } + + return rate; +} + +static unsigned long clk_leafclk_recalc(struct clk *clk) +{ + if (WARN_ON(!clk->parent)) + return clk->rate; + + return clk->parent->rate; } -static void __init clk_pll_init(struct clk *clk) +static unsigned long clk_pllclk_recalc(struct clk *clk) { u32 ctrl, mult = 1, prediv = 1, postdiv = 1; u8 bypass; struct pll_data *pll = clk->pll_data; + unsigned long rate = clk->rate; pll->base = IO_ADDRESS(pll->phys_base); ctrl = __raw_readl(pll->base + PLLCTL); - clk->rate = pll->input_rate = clk->parent->rate; + rate = pll->input_rate = clk->parent->rate; if (ctrl & PLLCTL_PLLEN) { bypass = 0; @@ -255,9 +328,9 @@ static void __init clk_pll_init(struct clk *clk) } if (!bypass) { - clk->rate /= prediv; - clk->rate *= mult; - clk->rate /= postdiv; + rate /= prediv; + rate *= mult; + rate /= postdiv; } pr_debug("PLL%d: input = %lu MHz [ ", @@ -270,8 +343,90 @@ static void __init clk_pll_init(struct clk *clk) pr_debug("* %d ", mult); if (postdiv > 1) pr_debug("/ %d ", postdiv); - pr_debug("] --> %lu MHz output.\n", clk->rate / 1000000); + pr_debug("] --> %lu MHz output.\n", rate / 1000000); + + return rate; +} + +/** + * davinci_set_pllrate - set the output rate of a given PLL. + * + * Note: Currently tested to work with OMAP-L138 only. + * + * @pll: pll whose rate needs to be changed. + * @prediv: The pre divider value. Passing 0 disables the pre-divider. + * @pllm: The multiplier value. Passing 0 leads to multiply-by-one. + * @postdiv: The post divider value. Passing 0 disables the post-divider. + */ +int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv, + unsigned int mult, unsigned int postdiv) +{ + u32 ctrl; + unsigned int locktime; + + if (pll->base == NULL) + return -EINVAL; + + /* + * PLL lock time required per OMAP-L138 datasheet is + * (2000 * prediv)/sqrt(pllm) OSCIN cycles. We approximate sqrt(pllm) + * as 4 and OSCIN cycle as 25 MHz. + */ + if (prediv) { + locktime = ((2000 * prediv) / 100); + prediv = (prediv - 1) | PLLDIV_EN; + } else { + locktime = 20; + } + if (postdiv) + postdiv = (postdiv - 1) | PLLDIV_EN; + if (mult) + mult = mult - 1; + + ctrl = __raw_readl(pll->base + PLLCTL); + + /* Switch the PLL to bypass mode */ + ctrl &= ~(PLLCTL_PLLENSRC | PLLCTL_PLLEN); + __raw_writel(ctrl, pll->base + PLLCTL); + + /* + * Wait for 4 OSCIN/CLKIN cycles to ensure that the PLLC has switched + * to bypass mode. Delay of 1us ensures we are good for all > 4MHz + * OSCIN/CLKIN inputs. Typically the input is ~25MHz. + */ + udelay(1); + + /* Reset and enable PLL */ + ctrl &= ~(PLLCTL_PLLRST | PLLCTL_PLLDIS); + __raw_writel(ctrl, pll->base + PLLCTL); + + if (pll->flags & PLL_HAS_PREDIV) + __raw_writel(prediv, pll->base + PREDIV); + + __raw_writel(mult, pll->base + PLLM); + + if (pll->flags & PLL_HAS_POSTDIV) + __raw_writel(postdiv, pll->base + POSTDIV); + + /* + * Wait for PLL to reset properly, OMAP-L138 datasheet says + * 'min' time = 125ns + */ + udelay(1); + + /* Bring PLL out of reset */ + ctrl |= PLLCTL_PLLRST; + __raw_writel(ctrl, pll->base + PLLCTL); + + udelay(locktime); + + /* Remove PLL from bypass mode */ + ctrl |= PLLCTL_PLLEN; + __raw_writel(ctrl, pll->base + PLLCTL); + + return 0; } +EXPORT_SYMBOL(davinci_set_pllrate); int __init davinci_clk_init(struct davinci_clk *clocks) { @@ -281,12 +436,23 @@ int __init davinci_clk_init(struct davinci_clk *clocks) for (c = clocks; c->lk.clk; c++) { clk = c->lk.clk; - if (clk->pll_data) - clk_pll_init(clk); + if (!clk->recalc) { + + /* Check if clock is a PLL */ + if (clk->pll_data) + clk->recalc = clk_pllclk_recalc; + + /* Else, if it is a PLL-derived clock */ + else if (clk->flags & CLK_PLL) + clk->recalc = clk_sysclk_recalc; + + /* Otherwise, it is a leaf clock (PSC clock) */ + else if (clk->parent) + clk->recalc = clk_leafclk_recalc; + } - /* Calculate rates for PLL-derived clocks */ - else if (clk->flags & CLK_PLL) - clk_sysclk_recalc(clk); + if (clk->recalc) + clk->rate = clk->recalc(clk); if (clk->lpsc) clk->flags |= CLK_PSC; @@ -352,9 +518,8 @@ dump_clock(struct seq_file *s, unsigned nest, struct clk *parent) /* REVISIT show device associations too */ /* cost is now small, but not linear... */ - list_for_each_entry(clk, &clocks, node) { - if (clk->parent == parent) - dump_clock(s, nest + NEST_DELTA, clk); + list_for_each_entry(clk, &parent->children, childnode) { + dump_clock(s, nest + NEST_DELTA, clk); } } diff --git a/arch/arm/mach-davinci/clock.h b/arch/arm/mach-davinci/clock.h index 27233cb4a2f..c92d77a3008 100644 --- a/arch/arm/mach-davinci/clock.h +++ b/arch/arm/mach-davinci/clock.h @@ -22,6 +22,10 @@ /* PLL/Reset register offsets */ #define PLLCTL 0x100 #define PLLCTL_PLLEN BIT(0) +#define PLLCTL_PLLPWRDN BIT(1) +#define PLLCTL_PLLRST BIT(3) +#define PLLCTL_PLLDIS BIT(4) +#define PLLCTL_PLLENSRC BIT(5) #define PLLCTL_CLKMODE BIT(8) #define PLLM 0x110 @@ -65,15 +69,20 @@ struct clk { const char *name; unsigned long rate; u8 usecount; - u8 flags; u8 lpsc; - u8 psc_ctlr; + u8 gpsc; + u32 flags; struct clk *parent; + struct list_head children; /* list of children */ + struct list_head childnode; /* parent's child list node */ struct pll_data *pll_data; u32 div_reg; + unsigned long (*recalc) (struct clk *); + int (*set_rate) (struct clk *clk, unsigned long rate); + int (*round_rate) (struct clk *clk, unsigned long rate); }; -/* Clock flags */ +/* Clock flags: SoC-specific flags start at BIT(16) */ #define ALWAYS_ENABLED BIT(1) #define CLK_PSC BIT(2) #define PSC_DSP BIT(3) /* PSC uses DSP domain, not ARM */ @@ -94,6 +103,8 @@ struct davinci_clk { } int davinci_clk_init(struct davinci_clk *clocks); +int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv, + unsigned int mult, unsigned int postdiv); extern struct platform_device davinci_wdt_device; diff --git a/arch/arm/mach-davinci/common.c b/arch/arm/mach-davinci/common.c index 61ede19c6b5..c2de94cde56 100644 --- a/arch/arm/mach-davinci/common.c +++ b/arch/arm/mach-davinci/common.c @@ -86,6 +86,8 @@ void __init davinci_common_init(struct davinci_soc_info *soc_info) dip = davinci_get_id(davinci_soc_info.jtag_id); if (!dip) { ret = -EINVAL; + pr_err("Unknown DaVinci JTAG ID 0x%x\n", + davinci_soc_info.jtag_id); goto err; } @@ -104,5 +106,5 @@ void __init davinci_common_init(struct davinci_soc_info *soc_info) return; err: - pr_err("davinci_common_init: SoC Initialization failed\n"); + panic("davinci_common_init: SoC Initialization failed\n"); } diff --git a/arch/arm/mach-davinci/cp_intc.c b/arch/arm/mach-davinci/cp_intc.c index 96c8e97a7de..52b287cf3a4 100644 --- a/arch/arm/mach-davinci/cp_intc.c +++ b/arch/arm/mach-davinci/cp_intc.c @@ -10,9 +10,6 @@ */ #include <linux/init.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/kernel.h> #include <linux/irq.h> #include <linux/io.h> diff --git a/arch/arm/mach-davinci/cpufreq.c b/arch/arm/mach-davinci/cpufreq.c new file mode 100644 index 00000000000..d3fa6de1e20 --- /dev/null +++ b/arch/arm/mach-davinci/cpufreq.c @@ -0,0 +1,226 @@ +/* + * CPU frequency scaling for DaVinci + * + * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on linux/arch/arm/plat-omap/cpu-omap.c. Original Copyright follows: + * + * Copyright (C) 2005 Nokia Corporation + * Written by Tony Lindgren <tony@atomide.com> + * + * Based on cpu-sa1110.c, Copyright (C) 2001 Russell King + * + * Copyright (C) 2007-2008 Texas Instruments, Inc. + * Updated to support OMAP3 + * Rajendra Nayak <rnayak@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/types.h> +#include <linux/cpufreq.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/platform_device.h> + +#include <mach/hardware.h> +#include <mach/cpufreq.h> +#include <mach/common.h> + +#include "clock.h" + +struct davinci_cpufreq { + struct device *dev; + struct clk *armclk; +}; +static struct davinci_cpufreq cpufreq; + +static int davinci_verify_speed(struct cpufreq_policy *policy) +{ + struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; + struct cpufreq_frequency_table *freq_table = pdata->freq_table; + struct clk *armclk = cpufreq.armclk; + + if (freq_table) + return cpufreq_frequency_table_verify(policy, freq_table); + + if (policy->cpu) + return -EINVAL; + + cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq, + policy->cpuinfo.max_freq); + + policy->min = clk_round_rate(armclk, policy->min * 1000) / 1000; + policy->max = clk_round_rate(armclk, policy->max * 1000) / 1000; + cpufreq_verify_within_limits(policy, policy->cpuinfo.min_freq, + policy->cpuinfo.max_freq); + return 0; +} + +static unsigned int davinci_getspeed(unsigned int cpu) +{ + if (cpu) + return 0; + + return clk_get_rate(cpufreq.armclk) / 1000; +} + +static int davinci_target(struct cpufreq_policy *policy, + unsigned int target_freq, unsigned int relation) +{ + int ret = 0; + unsigned int idx; + struct cpufreq_freqs freqs; + struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; + struct clk *armclk = cpufreq.armclk; + + /* + * Ensure desired rate is within allowed range. Some govenors + * (ondemand) will just pass target_freq=0 to get the minimum. + */ + if (target_freq < policy->cpuinfo.min_freq) + target_freq = policy->cpuinfo.min_freq; + if (target_freq > policy->cpuinfo.max_freq) + target_freq = policy->cpuinfo.max_freq; + + freqs.old = davinci_getspeed(0); + freqs.new = clk_round_rate(armclk, target_freq * 1000) / 1000; + freqs.cpu = 0; + + if (freqs.old == freqs.new) + return ret; + + cpufreq_debug_printk(CPUFREQ_DEBUG_DRIVER, + dev_driver_string(cpufreq.dev), + "transition: %u --> %u\n", freqs.old, freqs.new); + + ret = cpufreq_frequency_table_target(policy, pdata->freq_table, + freqs.new, relation, &idx); + if (ret) + return -EINVAL; + + cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + + /* if moving to higher frequency, up the voltage beforehand */ + if (pdata->set_voltage && freqs.new > freqs.old) + pdata->set_voltage(idx); + + ret = clk_set_rate(armclk, idx); + + /* if moving to lower freq, lower the voltage after lowering freq */ + if (pdata->set_voltage && freqs.new < freqs.old) + pdata->set_voltage(idx); + + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + return ret; +} + +static int __init davinci_cpu_init(struct cpufreq_policy *policy) +{ + int result = 0; + struct davinci_cpufreq_config *pdata = cpufreq.dev->platform_data; + struct cpufreq_frequency_table *freq_table = pdata->freq_table; + + if (policy->cpu != 0) + return -EINVAL; + + /* Finish platform specific initialization */ + if (pdata->init) { + result = pdata->init(); + if (result) + return result; + } + + policy->cur = policy->min = policy->max = davinci_getspeed(0); + + if (freq_table) { + result = cpufreq_frequency_table_cpuinfo(policy, freq_table); + if (!result) + cpufreq_frequency_table_get_attr(freq_table, + policy->cpu); + } else { + policy->cpuinfo.min_freq = policy->min; + policy->cpuinfo.max_freq = policy->max; + } + + policy->min = policy->cpuinfo.min_freq; + policy->max = policy->cpuinfo.max_freq; + policy->cur = davinci_getspeed(0); + + /* + * Time measurement across the target() function yields ~1500-1800us + * time taken with no drivers on notification list. + * Setting the latency to 2000 us to accomodate addition of drivers + * to pre/post change notification list. + */ + policy->cpuinfo.transition_latency = 2000 * 1000; + return 0; +} + +static int davinci_cpu_exit(struct cpufreq_policy *policy) +{ + cpufreq_frequency_table_put_attr(policy->cpu); + return 0; +} + +static struct freq_attr *davinci_cpufreq_attr[] = { + &cpufreq_freq_attr_scaling_available_freqs, + NULL, +}; + +static struct cpufreq_driver davinci_driver = { + .flags = CPUFREQ_STICKY, + .verify = davinci_verify_speed, + .target = davinci_target, + .get = davinci_getspeed, + .init = davinci_cpu_init, + .exit = davinci_cpu_exit, + .name = "davinci", + .attr = davinci_cpufreq_attr, +}; + +static int __init davinci_cpufreq_probe(struct platform_device *pdev) +{ + struct davinci_cpufreq_config *pdata = pdev->dev.platform_data; + + if (!pdata) + return -EINVAL; + if (!pdata->freq_table) + return -EINVAL; + + cpufreq.dev = &pdev->dev; + + cpufreq.armclk = clk_get(NULL, "arm"); + if (IS_ERR(cpufreq.armclk)) { + dev_err(cpufreq.dev, "Unable to get ARM clock\n"); + return PTR_ERR(cpufreq.armclk); + } + + return cpufreq_register_driver(&davinci_driver); +} + +static int __exit davinci_cpufreq_remove(struct platform_device *pdev) +{ + clk_put(cpufreq.armclk); + + return cpufreq_unregister_driver(&davinci_driver); +} + +static struct platform_driver davinci_cpufreq_driver = { + .driver = { + .name = "cpufreq-davinci", + .owner = THIS_MODULE, + }, + .remove = __exit_p(davinci_cpufreq_remove), +}; + +static int __init davinci_cpufreq_init(void) +{ + return platform_driver_probe(&davinci_cpufreq_driver, + davinci_cpufreq_probe); +} +late_initcall(davinci_cpufreq_init); + diff --git a/arch/arm/mach-davinci/cpuidle.c b/arch/arm/mach-davinci/cpuidle.c new file mode 100644 index 00000000000..97a90f36fc9 --- /dev/null +++ b/arch/arm/mach-davinci/cpuidle.c @@ -0,0 +1,197 @@ +/* + * CPU idle for DaVinci SoCs + * + * Copyright (C) 2009 Texas Instruments Incorporated. http://www.ti.com/ + * + * Derived from Marvell Kirkwood CPU idle code + * (arch/arm/mach-kirkwood/cpuidle.c) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/cpuidle.h> +#include <linux/io.h> +#include <asm/proc-fns.h> + +#include <mach/cpuidle.h> + +#define DAVINCI_CPUIDLE_MAX_STATES 2 + +struct davinci_ops { + void (*enter) (u32 flags); + void (*exit) (u32 flags); + u32 flags; +}; + +/* fields in davinci_ops.flags */ +#define DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN BIT(0) + +static struct cpuidle_driver davinci_idle_driver = { + .name = "cpuidle-davinci", + .owner = THIS_MODULE, +}; + +static DEFINE_PER_CPU(struct cpuidle_device, davinci_cpuidle_device); +static void __iomem *ddr2_reg_base; + +#define DDR2_SDRCR_OFFSET 0xc +#define DDR2_SRPD_BIT BIT(23) +#define DDR2_LPMODEN_BIT BIT(31) + +static void davinci_save_ddr_power(int enter, bool pdown) +{ + u32 val; + + val = __raw_readl(ddr2_reg_base + DDR2_SDRCR_OFFSET); + + if (enter) { + if (pdown) + val |= DDR2_SRPD_BIT; + else + val &= ~DDR2_SRPD_BIT; + val |= DDR2_LPMODEN_BIT; + } else { + val &= ~(DDR2_SRPD_BIT | DDR2_LPMODEN_BIT); + } + + __raw_writel(val, ddr2_reg_base + DDR2_SDRCR_OFFSET); +} + +static void davinci_c2state_enter(u32 flags) +{ + davinci_save_ddr_power(1, !!(flags & DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN)); +} + +static void davinci_c2state_exit(u32 flags) +{ + davinci_save_ddr_power(0, !!(flags & DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN)); +} + +static struct davinci_ops davinci_states[DAVINCI_CPUIDLE_MAX_STATES] = { + [1] = { + .enter = davinci_c2state_enter, + .exit = davinci_c2state_exit, + }, +}; + +/* Actual code that puts the SoC in different idle states */ +static int davinci_enter_idle(struct cpuidle_device *dev, + struct cpuidle_state *state) +{ + struct davinci_ops *ops = cpuidle_get_statedata(state); + struct timeval before, after; + int idle_time; + + local_irq_disable(); + do_gettimeofday(&before); + + if (ops && ops->enter) + ops->enter(ops->flags); + /* Wait for interrupt state */ + cpu_do_idle(); + if (ops && ops->exit) + ops->exit(ops->flags); + + do_gettimeofday(&after); + local_irq_enable(); + idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC + + (after.tv_usec - before.tv_usec); + return idle_time; +} + +static int __init davinci_cpuidle_probe(struct platform_device *pdev) +{ + int ret; + struct cpuidle_device *device; + struct davinci_cpuidle_config *pdata = pdev->dev.platform_data; + struct resource *ddr2_regs; + resource_size_t len; + + device = &per_cpu(davinci_cpuidle_device, smp_processor_id()); + + if (!pdata) { + dev_err(&pdev->dev, "cannot get platform data\n"); + return -ENOENT; + } + + ddr2_regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!ddr2_regs) { + dev_err(&pdev->dev, "cannot get DDR2 controller register base"); + return -ENODEV; + } + + len = resource_size(ddr2_regs); + + ddr2_regs = request_mem_region(ddr2_regs->start, len, ddr2_regs->name); + if (!ddr2_regs) + return -EBUSY; + + ddr2_reg_base = ioremap(ddr2_regs->start, len); + if (!ddr2_reg_base) { + ret = -ENOMEM; + goto ioremap_fail; + } + + ret = cpuidle_register_driver(&davinci_idle_driver); + if (ret) { + dev_err(&pdev->dev, "failed to register driver\n"); + goto driver_register_fail; + } + + /* Wait for interrupt state */ + device->states[0].enter = davinci_enter_idle; + device->states[0].exit_latency = 1; + device->states[0].target_residency = 10000; + device->states[0].flags = CPUIDLE_FLAG_TIME_VALID; + strcpy(device->states[0].name, "WFI"); + strcpy(device->states[0].desc, "Wait for interrupt"); + + /* Wait for interrupt and DDR self refresh state */ + device->states[1].enter = davinci_enter_idle; + device->states[1].exit_latency = 10; + device->states[1].target_residency = 10000; + device->states[1].flags = CPUIDLE_FLAG_TIME_VALID; + strcpy(device->states[1].name, "DDR SR"); + strcpy(device->states[1].desc, "WFI and DDR Self Refresh"); + if (pdata->ddr2_pdown) + davinci_states[1].flags |= DAVINCI_CPUIDLE_FLAGS_DDR2_PWDN; + cpuidle_set_statedata(&device->states[1], &davinci_states[1]); + + device->state_count = DAVINCI_CPUIDLE_MAX_STATES; + + ret = cpuidle_register_device(device); + if (ret) { + dev_err(&pdev->dev, "failed to register device\n"); + goto device_register_fail; + } + + return 0; + +device_register_fail: + cpuidle_unregister_driver(&davinci_idle_driver); +driver_register_fail: + iounmap(ddr2_reg_base); +ioremap_fail: + release_mem_region(ddr2_regs->start, len); + return ret; +} + +static struct platform_driver davinci_cpuidle_driver = { + .driver = { + .name = "cpuidle-davinci", + .owner = THIS_MODULE, + }, +}; + +static int __init davinci_cpuidle_init(void) +{ + return platform_driver_probe(&davinci_cpuidle_driver, + davinci_cpuidle_probe); +} +device_initcall(davinci_cpuidle_init); + diff --git a/arch/arm/mach-davinci/da830.c b/arch/arm/mach-davinci/da830.c index 19b2748357f..b22b5cf0425 100644 --- a/arch/arm/mach-davinci/da830.c +++ b/arch/arm/mach-davinci/da830.c @@ -8,22 +8,17 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> -#include <linux/platform_device.h> #include <asm/mach/map.h> -#include <mach/clock.h> #include <mach/psc.h> -#include <mach/mux.h> #include <mach/irqs.h> #include <mach/cputype.h> #include <mach/common.h> #include <mach/time.h> #include <mach/da8xx.h> -#include <mach/asp.h> #include "clock.h" #include "mux.h" @@ -193,14 +188,14 @@ static struct clk uart1_clk = { .name = "uart1", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_UART1, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk uart2_clk = { .name = "uart2", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_UART2, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk spi0_clk = { @@ -213,98 +208,98 @@ static struct clk spi1_clk = { .name = "spi1", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_SPI1, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk ecap0_clk = { .name = "ecap0", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_ECAP, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk ecap1_clk = { .name = "ecap1", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_ECAP, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk ecap2_clk = { .name = "ecap2", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_ECAP, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk pwm0_clk = { .name = "pwm0", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_PWM, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk pwm1_clk = { .name = "pwm1", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_PWM, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk pwm2_clk = { .name = "pwm2", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_PWM, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk eqep0_clk = { .name = "eqep0", .parent = &pll0_sysclk2, .lpsc = DA830_LPSC1_EQEP, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk eqep1_clk = { .name = "eqep1", .parent = &pll0_sysclk2, .lpsc = DA830_LPSC1_EQEP, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk lcdc_clk = { .name = "lcdc", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_LCDC, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk mcasp0_clk = { .name = "mcasp0", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_McASP0, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk mcasp1_clk = { .name = "mcasp1", .parent = &pll0_sysclk2, .lpsc = DA830_LPSC1_McASP1, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk mcasp2_clk = { .name = "mcasp2", .parent = &pll0_sysclk2, .lpsc = DA830_LPSC1_McASP2, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk usb20_clk = { .name = "usb20", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_USB20, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk aemif_clk = { @@ -332,36 +327,36 @@ static struct clk emac_clk = { .name = "emac", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_CPGMAC, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk gpio_clk = { .name = "gpio", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_GPIO, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk i2c1_clk = { .name = "i2c1", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_I2C, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk usb11_clk = { .name = "usb11", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_USB11, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk emif3_clk = { .name = "emif3", .parent = &pll0_sysclk5, .lpsc = DA8XX_LPSC1_EMIF3C, + .gpsc = 1, .flags = ALWAYS_ENABLED, - .psc_ctlr = 1, }; static struct clk arm_clk = { @@ -411,7 +406,7 @@ static struct davinci_clk da830_clks[] = { CLK(NULL, "pwm2", &pwm2_clk), CLK("eqep.0", NULL, &eqep0_clk), CLK("eqep.1", NULL, &eqep1_clk), - CLK("da830_lcdc", NULL, &lcdc_clk), + CLK("da8xx_lcdc.0", NULL, &lcdc_clk), CLK("davinci-mcasp.0", NULL, &mcasp0_clk), CLK("davinci-mcasp.1", NULL, &mcasp1_clk), CLK("davinci-mcasp.2", NULL, &mcasp2_clk), @@ -1143,7 +1138,21 @@ static struct davinci_id da830_ids[] = { .part_no = 0xb7df, .manufacturer = 0x017, /* 0x02f >> 1 */ .cpu_id = DAVINCI_CPU_ID_DA830, - .name = "da830/omap l137", + .name = "da830/omap-l137 rev1.0", + }, + { + .variant = 0x8, + .part_no = 0xb7df, + .manufacturer = 0x017, + .cpu_id = DAVINCI_CPU_ID_DA830, + .name = "da830/omap-l137 rev1.1", + }, + { + .variant = 0x9, + .part_no = 0xb7df, + .manufacturer = 0x017, + .cpu_id = DAVINCI_CPU_ID_DA830, + .name = "da830/omap-l137 rev2.0", }, }; @@ -1178,13 +1187,11 @@ static struct davinci_timer_info da830_timer_info = { static struct davinci_soc_info davinci_soc_info_da830 = { .io_desc = da830_io_desc, .io_desc_num = ARRAY_SIZE(da830_io_desc), - .jtag_id_base = IO_ADDRESS(DA8XX_JTAG_ID_REG), .ids = da830_ids, .ids_num = ARRAY_SIZE(da830_ids), .cpu_clks = da830_clks, .psc_bases = da830_psc_bases, .psc_bases_num = ARRAY_SIZE(da830_psc_bases), - .pinmux_base = IO_ADDRESS(DA8XX_BOOT_CFG_BASE + 0x120), .pinmux_pins = da830_pins, .pinmux_pins_num = ARRAY_SIZE(da830_pins), .intc_base = (void __iomem *)DA8XX_CP_INTC_VIRT, @@ -1201,5 +1208,13 @@ static struct davinci_soc_info davinci_soc_info_da830 = { void __init da830_init(void) { + da8xx_syscfg_base = ioremap(DA8XX_SYSCFG_BASE, SZ_4K); + if (WARN(!da8xx_syscfg_base, "Unable to map syscfg module")) + return; + + davinci_soc_info_da830.jtag_id_base = + DA8XX_SYSCFG_VIRT(DA8XX_JTAG_ID_REG); + davinci_soc_info_da830.pinmux_base = DA8XX_SYSCFG_VIRT(0x120); + davinci_common_init(&davinci_soc_info_da830); } diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 192d719a47d..717806c6cef 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -11,31 +11,41 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/platform_device.h> +#include <linux/cpufreq.h> +#include <linux/regulator/consumer.h> #include <asm/mach/map.h> -#include <mach/clock.h> #include <mach/psc.h> -#include <mach/mux.h> #include <mach/irqs.h> #include <mach/cputype.h> #include <mach/common.h> #include <mach/time.h> #include <mach/da8xx.h> +#include <mach/cpufreq.h> #include "clock.h" #include "mux.h" +/* SoC specific clock flags */ +#define DA850_CLK_ASYNC3 BIT(16) + #define DA850_PLL1_BASE 0x01e1a000 #define DA850_TIMER64P2_BASE 0x01f0c000 #define DA850_TIMER64P3_BASE 0x01f0d000 #define DA850_REF_FREQ 24000000 +#define CFGCHIP3_ASYNC3_CLKSRC BIT(4) +#define CFGCHIP0_PLL_MASTER_LOCK BIT(4) + +static int da850_set_armrate(struct clk *clk, unsigned long rate); +static int da850_round_armrate(struct clk *clk, unsigned long rate); +static int da850_set_pll0rate(struct clk *clk, unsigned long armrate); + static struct pll_data pll0_data = { .num = 1, .phys_base = DA8XX_PLL0_BASE, @@ -52,6 +62,7 @@ static struct clk pll0_clk = { .parent = &ref_clk, .pll_data = &pll0_data, .flags = CLK_PLL, + .set_rate = da850_set_pll0rate, }; static struct clk pll0_aux_clk = { @@ -210,16 +221,16 @@ static struct clk tpcc1_clk = { .name = "tpcc1", .parent = &pll0_sysclk2, .lpsc = DA850_LPSC1_TPCC1, + .gpsc = 1, .flags = CLK_PSC | ALWAYS_ENABLED, - .psc_ctlr = 1, }; static struct clk tptc2_clk = { .name = "tptc2", .parent = &pll0_sysclk2, .lpsc = DA850_LPSC1_TPTC2, + .gpsc = 1, .flags = ALWAYS_ENABLED, - .psc_ctlr = 1, }; static struct clk uart0_clk = { @@ -232,14 +243,16 @@ static struct clk uart1_clk = { .name = "uart1", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_UART1, - .psc_ctlr = 1, + .gpsc = 1, + .flags = DA850_CLK_ASYNC3, }; static struct clk uart2_clk = { .name = "uart2", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_UART2, - .psc_ctlr = 1, + .gpsc = 1, + .flags = DA850_CLK_ASYNC3, }; static struct clk aintc_clk = { @@ -253,22 +266,22 @@ static struct clk gpio_clk = { .name = "gpio", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_GPIO, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk i2c1_clk = { .name = "i2c1", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_I2C, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk emif3_clk = { .name = "emif3", .parent = &pll0_sysclk5, .lpsc = DA8XX_LPSC1_EMIF3C, + .gpsc = 1, .flags = ALWAYS_ENABLED, - .psc_ctlr = 1, }; static struct clk arm_clk = { @@ -276,6 +289,8 @@ static struct clk arm_clk = { .parent = &pll0_sysclk6, .lpsc = DA8XX_LPSC0_ARM, .flags = ALWAYS_ENABLED, + .set_rate = da850_set_armrate, + .round_rate = da850_round_armrate, }; static struct clk rmii_clk = { @@ -287,21 +302,22 @@ static struct clk emac_clk = { .name = "emac", .parent = &pll0_sysclk4, .lpsc = DA8XX_LPSC1_CPGMAC, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk mcasp_clk = { .name = "mcasp", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_McASP0, - .psc_ctlr = 1, + .gpsc = 1, + .flags = DA850_CLK_ASYNC3, }; static struct clk lcdc_clk = { .name = "lcdc", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC1_LCDC, - .psc_ctlr = 1, + .gpsc = 1, }; static struct clk mmcsd_clk = { @@ -404,6 +420,14 @@ static const struct mux_config da850_pins[] = { MUX_CFG(DA850, MII_RXD_0, 3, 28, 15, 8, false) MUX_CFG(DA850, MDIO_CLK, 4, 0, 15, 8, false) MUX_CFG(DA850, MDIO_D, 4, 4, 15, 8, false) + MUX_CFG(DA850, RMII_TXD_0, 14, 12, 15, 8, false) + MUX_CFG(DA850, RMII_TXD_1, 14, 8, 15, 8, false) + MUX_CFG(DA850, RMII_TXEN, 14, 16, 15, 8, false) + MUX_CFG(DA850, RMII_CRS_DV, 15, 4, 15, 8, false) + MUX_CFG(DA850, RMII_RXD_0, 14, 24, 15, 8, false) + MUX_CFG(DA850, RMII_RXD_1, 14, 20, 15, 8, false) + MUX_CFG(DA850, RMII_RXER, 14, 28, 15, 8, false) + MUX_CFG(DA850, RMII_MHZ_50_CLK, 15, 0, 15, 0, false) /* McASP function */ MUX_CFG(DA850, ACLKR, 0, 0, 15, 1, false) MUX_CFG(DA850, ACLKX, 0, 4, 15, 1, false) @@ -506,8 +530,9 @@ static const struct mux_config da850_pins[] = { MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false) MUX_CFG(DA850, NEMA_CS_2, 7, 0, 15, 1, false) /* GPIO function */ + MUX_CFG(DA850, GPIO2_6, 6, 4, 15, 8, false) + MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false) MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false) - MUX_CFG(DA850, GPIO8_10, 18, 28, 15, 8, false) MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false) MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false) #endif @@ -547,6 +572,14 @@ const short da850_cpgmac_pins[] __initdata = { -1 }; +const short da850_rmii_pins[] __initdata = { + DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, + DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, + DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + const short da850_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, @@ -555,12 +588,11 @@ const short da850_mcasp_pins[] __initdata = { }; const short da850_lcdcntl_pins[] __initdata = { - DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, DA850_LCD_D_4, - DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, DA850_LCD_D_8, - DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, DA850_LCD_D_12, - DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, DA850_LCD_PCLK, - DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, DA850_GPIO2_15, - DA850_GPIO8_10, + DA850_LCD_D_0, DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, + DA850_LCD_D_4, DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, + DA850_LCD_D_8, DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, + DA850_LCD_D_12, DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, + DA850_LCD_PCLK, DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, -1 }; @@ -790,16 +822,221 @@ static struct davinci_timer_info da850_timer_info = { .clocksource_id = T0_TOP, }; +static void da850_set_async3_src(int pllnum) +{ + struct clk *clk, *newparent = pllnum ? &pll1_sysclk2 : &pll0_sysclk2; + struct davinci_clk *c; + unsigned int v; + int ret; + + for (c = da850_clks; c->lk.clk; c++) { + clk = c->lk.clk; + if (clk->flags & DA850_CLK_ASYNC3) { + ret = clk_set_parent(clk, newparent); + WARN(ret, "DA850: unable to re-parent clock %s", + clk->name); + } + } + + v = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG)); + if (pllnum) + v |= CFGCHIP3_ASYNC3_CLKSRC; + else + v &= ~CFGCHIP3_ASYNC3_CLKSRC; + __raw_writel(v, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP3_REG)); +} + +#ifdef CONFIG_CPU_FREQ +/* + * Notes: + * According to the TRM, minimum PLLM results in maximum power savings. + * The OPP definitions below should keep the PLLM as low as possible. + * + * The output of the PLLM must be between 400 to 600 MHz. + * This rules out prediv of anything but divide-by-one for 24Mhz OSC input. + */ +struct da850_opp { + unsigned int freq; /* in KHz */ + unsigned int prediv; + unsigned int mult; + unsigned int postdiv; + unsigned int cvdd_min; /* in uV */ + unsigned int cvdd_max; /* in uV */ +}; + +static const struct da850_opp da850_opp_300 = { + .freq = 300000, + .prediv = 1, + .mult = 25, + .postdiv = 2, + .cvdd_min = 1140000, + .cvdd_max = 1320000, +}; + +static const struct da850_opp da850_opp_200 = { + .freq = 200000, + .prediv = 1, + .mult = 25, + .postdiv = 3, + .cvdd_min = 1050000, + .cvdd_max = 1160000, +}; + +static const struct da850_opp da850_opp_96 = { + .freq = 96000, + .prediv = 1, + .mult = 20, + .postdiv = 5, + .cvdd_min = 950000, + .cvdd_max = 1050000, +}; + +#define OPP(freq) \ + { \ + .index = (unsigned int) &da850_opp_##freq, \ + .frequency = freq * 1000, \ + } + +static struct cpufreq_frequency_table da850_freq_table[] = { + OPP(300), + OPP(200), + OPP(96), + { + .index = 0, + .frequency = CPUFREQ_TABLE_END, + }, +}; + +#ifdef CONFIG_REGULATOR +static struct regulator *cvdd; + +static int da850_set_voltage(unsigned int index) +{ + struct da850_opp *opp; + + if (!cvdd) + return -ENODEV; + + opp = (struct da850_opp *) da850_freq_table[index].index; + + return regulator_set_voltage(cvdd, opp->cvdd_min, opp->cvdd_max); +} + +static int da850_regulator_init(void) +{ + cvdd = regulator_get(NULL, "cvdd"); + if (WARN(IS_ERR(cvdd), "Unable to obtain voltage regulator for CVDD;" + " voltage scaling unsupported\n")) { + return PTR_ERR(cvdd); + } + + return 0; +} +#endif + +static struct davinci_cpufreq_config cpufreq_info = { + .freq_table = &da850_freq_table[0], +#ifdef CONFIG_REGULATOR + .init = da850_regulator_init, + .set_voltage = da850_set_voltage, +#endif +}; + +static struct platform_device da850_cpufreq_device = { + .name = "cpufreq-davinci", + .dev = { + .platform_data = &cpufreq_info, + }, +}; + +int __init da850_register_cpufreq(void) +{ + return platform_device_register(&da850_cpufreq_device); +} + +static int da850_round_armrate(struct clk *clk, unsigned long rate) +{ + int i, ret = 0, diff; + unsigned int best = (unsigned int) -1; + + rate /= 1000; /* convert to kHz */ + + for (i = 0; da850_freq_table[i].frequency != CPUFREQ_TABLE_END; i++) { + diff = da850_freq_table[i].frequency - rate; + if (diff < 0) + diff = -diff; + + if (diff < best) { + best = diff; + ret = da850_freq_table[i].frequency; + } + } + + return ret * 1000; +} + +static int da850_set_armrate(struct clk *clk, unsigned long index) +{ + struct clk *pllclk = &pll0_clk; + + return clk_set_rate(pllclk, index); +} + +static int da850_set_pll0rate(struct clk *clk, unsigned long index) +{ + unsigned int prediv, mult, postdiv; + struct da850_opp *opp; + struct pll_data *pll = clk->pll_data; + unsigned int v; + int ret; + + opp = (struct da850_opp *) da850_freq_table[index].index; + prediv = opp->prediv; + mult = opp->mult; + postdiv = opp->postdiv; + + /* Unlock writing to PLL registers */ + v = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP0_REG)); + v &= ~CFGCHIP0_PLL_MASTER_LOCK; + __raw_writel(v, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP0_REG)); + + ret = davinci_set_pllrate(pll, prediv, mult, postdiv); + if (WARN_ON(ret)) + return ret; + + return 0; +} +#else +int __init da850_register_cpufreq(void) +{ + return 0; +} + +static int da850_set_armrate(struct clk *clk, unsigned long rate) +{ + return -EINVAL; +} + +static int da850_set_pll0rate(struct clk *clk, unsigned long armrate) +{ + return -EINVAL; +} + +static int da850_round_armrate(struct clk *clk, unsigned long rate) +{ + return clk->rate; +} +#endif + + static struct davinci_soc_info davinci_soc_info_da850 = { .io_desc = da850_io_desc, .io_desc_num = ARRAY_SIZE(da850_io_desc), - .jtag_id_base = IO_ADDRESS(DA8XX_JTAG_ID_REG), .ids = da850_ids, .ids_num = ARRAY_SIZE(da850_ids), .cpu_clks = da850_clks, .psc_bases = da850_psc_bases, .psc_bases_num = ARRAY_SIZE(da850_psc_bases), - .pinmux_base = IO_ADDRESS(DA8XX_BOOT_CFG_BASE + 0x120), .pinmux_pins = da850_pins, .pinmux_pins_num = ARRAY_SIZE(da850_pins), .intc_base = (void __iomem *)DA8XX_CP_INTC_VIRT, @@ -816,5 +1053,22 @@ static struct davinci_soc_info davinci_soc_info_da850 = { void __init da850_init(void) { + da8xx_syscfg_base = ioremap(DA8XX_SYSCFG_BASE, SZ_4K); + if (WARN(!da8xx_syscfg_base, "Unable to map syscfg module")) + return; + + davinci_soc_info_da850.jtag_id_base = + DA8XX_SYSCFG_VIRT(DA8XX_JTAG_ID_REG); + davinci_soc_info_da850.pinmux_base = DA8XX_SYSCFG_VIRT(0x120); + davinci_common_init(&davinci_soc_info_da850); + + /* + * Move the clock source of Async3 domain to PLL1 SYSCLK2. + * This helps keeping the peripherals on this domain insulated + * from CPU frequency changes caused by DVFS. The firmware sets + * both PLL0 and PLL1 to the same frequency so, there should not + * be any noticible change even in non-DVFS use cases. + */ + da850_set_async3_src(1); } diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index 58ad5b66fd6..dd2d32c4ce8 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -10,8 +10,6 @@ * the Free Software Foundation; either version 2 of the License, or * (at your option) any later version. */ -#include <linux/module.h> -#include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> @@ -21,7 +19,7 @@ #include <mach/common.h> #include <mach/time.h> #include <mach/da8xx.h> -#include <video/da8xx-fb.h> +#include <mach/cpuidle.h> #include "clock.h" @@ -30,6 +28,7 @@ #define DA8XX_TPTC1_BASE 0x01c08400 #define DA8XX_WDOG_BASE 0x01c21000 /* DA8XX_TIMER64P1_BASE */ #define DA8XX_I2C0_BASE 0x01c22000 +#define DA8XX_RTC_BASE 0x01C23000 #define DA8XX_EMAC_CPPI_PORT_BASE 0x01e20000 #define DA8XX_EMAC_CPGMACSS_BASE 0x01e22000 #define DA8XX_EMAC_CPGMAC_BASE 0x01e23000 @@ -43,6 +42,8 @@ #define DA8XX_MDIO_REG_OFFSET 0x4000 #define DA8XX_EMAC_CTRL_RAM_SIZE SZ_8K +void __iomem *da8xx_syscfg_base; + static struct plat_serial8250_port da8xx_serial_pdata[] = { { .mapbase = DA8XX_UART0_BASE, @@ -282,6 +283,11 @@ static struct platform_device da8xx_emac_device = { .resource = da8xx_emac_resources, }; +int __init da8xx_register_emac(void) +{ + return platform_device_register(&da8xx_emac_device); +} + static struct resource da830_mcasp1_resources[] = { { .name = "mcasp1", @@ -338,12 +344,7 @@ static struct platform_device da850_mcasp_device = { .resource = da850_mcasp_resources, }; -int __init da8xx_register_emac(void) -{ - return platform_device_register(&da8xx_emac_device); -} - -void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata) +void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata) { /* DA830/OMAP-L137 has 3 instances of McASP */ if (cpu_is_davinci_da830() && id == 1) { @@ -379,10 +380,16 @@ static struct lcd_ctrl_config lcd_cfg = { .raster_order = 0, }; -static struct da8xx_lcdc_platform_data da850_evm_lcdc_pdata = { - .manu_name = "sharp", - .controller_data = &lcd_cfg, - .type = "Sharp_LK043T1DG01", +struct da8xx_lcdc_platform_data sharp_lcd035q3dg01_pdata = { + .manu_name = "sharp", + .controller_data = &lcd_cfg, + .type = "Sharp_LCD035Q3DG01", +}; + +struct da8xx_lcdc_platform_data sharp_lk043t1dg01_pdata = { + .manu_name = "sharp", + .controller_data = &lcd_cfg, + .type = "Sharp_LK043T1DG01", }; static struct resource da8xx_lcdc_resources[] = { @@ -398,19 +405,17 @@ static struct resource da8xx_lcdc_resources[] = { }, }; -static struct platform_device da850_lcdc_device = { +static struct platform_device da8xx_lcdc_device = { .name = "da8xx_lcdc", .id = 0, .num_resources = ARRAY_SIZE(da8xx_lcdc_resources), .resource = da8xx_lcdc_resources, - .dev = { - .platform_data = &da850_evm_lcdc_pdata, - } }; -int __init da8xx_register_lcdc(void) +int __init da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata) { - return platform_device_register(&da850_lcdc_device); + da8xx_lcdc_device.dev.platform_data = pdata; + return platform_device_register(&da8xx_lcdc_device); } static struct resource da8xx_mmcsd0_resources[] = { @@ -448,3 +453,66 @@ int __init da8xx_register_mmcsd0(struct davinci_mmc_config *config) da8xx_mmcsd0_device.dev.platform_data = config; return platform_device_register(&da8xx_mmcsd0_device); } + +static struct resource da8xx_rtc_resources[] = { + { + .start = DA8XX_RTC_BASE, + .end = DA8XX_RTC_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + { /* timer irq */ + .start = IRQ_DA8XX_RTC, + .end = IRQ_DA8XX_RTC, + .flags = IORESOURCE_IRQ, + }, + { /* alarm irq */ + .start = IRQ_DA8XX_RTC, + .end = IRQ_DA8XX_RTC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device da8xx_rtc_device = { + .name = "omap_rtc", + .id = -1, + .num_resources = ARRAY_SIZE(da8xx_rtc_resources), + .resource = da8xx_rtc_resources, +}; + +int da8xx_register_rtc(void) +{ + /* Unlock the rtc's registers */ + __raw_writel(0x83e70b13, IO_ADDRESS(DA8XX_RTC_BASE + 0x6c)); + __raw_writel(0x95a4f1e0, IO_ADDRESS(DA8XX_RTC_BASE + 0x70)); + + return platform_device_register(&da8xx_rtc_device); +} + +static struct resource da8xx_cpuidle_resources[] = { + { + .start = DA8XX_DDR2_CTL_BASE, + .end = DA8XX_DDR2_CTL_BASE + SZ_32K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +/* DA8XX devices support DDR2 power down */ +static struct davinci_cpuidle_config da8xx_cpuidle_pdata = { + .ddr2_pdown = 1, +}; + + +static struct platform_device da8xx_cpuidle_device = { + .name = "cpuidle-davinci", + .num_resources = ARRAY_SIZE(da8xx_cpuidle_resources), + .resource = da8xx_cpuidle_resources, + .dev = { + .platform_data = &da8xx_cpuidle_pdata, + }, +}; + +int __init da8xx_register_cpuidle(void) +{ + return platform_device_register(&da8xx_cpuidle_device); +} + diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c index a55b650db71..147949650c2 100644 --- a/arch/arm/mach-davinci/devices.c +++ b/arch/arm/mach-davinci/devices.c @@ -9,15 +9,11 @@ * (at your option) any later version. */ -#include <linux/module.h> -#include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/io.h> -#include <asm/mach/map.h> - #include <mach/hardware.h> #include <mach/i2c.h> #include <mach/irqs.h> @@ -177,7 +173,7 @@ void __init davinci_setup_mmc(int module, struct davinci_mmc_config *config) mmcsd1_resources[0].start = DM365_MMCSD1_BASE; mmcsd1_resources[0].end = DM365_MMCSD1_BASE + SZ_4K - 1; - mmcsd0_resources[2].start = IRQ_DM365_SDIOINT1; + mmcsd1_resources[2].start = IRQ_DM365_SDIOINT1; } else break; diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index 059670018af..dedf4d4f3a2 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -8,7 +8,6 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/serial_8250.h> @@ -21,7 +20,6 @@ #include <asm/mach/map.h> #include <mach/dm355.h> -#include <mach/clock.h> #include <mach/cputype.h> #include <mach/edma.h> #include <mach/psc.h> diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index e8151743470..2ec619ec165 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -12,7 +12,6 @@ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/serial_8250.h> @@ -23,7 +22,6 @@ #include <asm/mach/map.h> #include <mach/dm365.h> -#include <mach/clock.h> #include <mach/cputype.h> #include <mach/edma.h> #include <mach/psc.h> @@ -32,6 +30,8 @@ #include <mach/time.h> #include <mach/serial.h> #include <mach/common.h> +#include <mach/asp.h> +#include <mach/keyscan.h> #include "clock.h" #include "mux.h" @@ -369,7 +369,7 @@ static struct clk timer3_clk = { static struct clk usb_clk = { .name = "usb", - .parent = &pll2_sysclk1, + .parent = &pll1_aux_clk, .lpsc = DAVINCI_LPSC_USB, }; @@ -456,7 +456,7 @@ static struct davinci_clk dm365_clks[] = { CLK(NULL, "usb", &usb_clk), CLK("davinci_emac.1", NULL, &emac_clk), CLK("voice_codec", NULL, &voicecodec_clk), - CLK("soc-audio.0", NULL, &asp0_clk), + CLK("davinci-asp.0", NULL, &asp0_clk), CLK(NULL, "rto", &rto_clk), CLK(NULL, "mjcp", &mjcp_clk), CLK(NULL, NULL, NULL), @@ -531,7 +531,7 @@ MUX_CFG(DM365, EMAC_CRS, 3, 2, 1, 1, false) MUX_CFG(DM365, EMAC_MDIO, 3, 1, 1, 1, false) MUX_CFG(DM365, EMAC_MDCLK, 3, 0, 1, 1, false) -MUX_CFG(DM365, KEYPAD, 2, 0, 0x3f, 0x3f, false) +MUX_CFG(DM365, KEYSCAN, 2, 0, 0x3f, 0x3f, false) MUX_CFG(DM365, PWM0, 1, 0, 3, 2, false) MUX_CFG(DM365, PWM0_G23, 3, 26, 3, 3, false) @@ -603,6 +603,9 @@ INT_CFG(DM365, INT_IMX1_ENABLE, 24, 1, 1, false) INT_CFG(DM365, INT_IMX1_DISABLE, 24, 1, 0, false) INT_CFG(DM365, INT_NSF_ENABLE, 25, 1, 1, false) INT_CFG(DM365, INT_NSF_DISABLE, 25, 1, 0, false) + +EVT_CFG(DM365, EVT2_ASP_TX, 0, 1, 0, false) +EVT_CFG(DM365, EVT3_ASP_RX, 1, 1, 0, false) #endif }; @@ -696,6 +699,7 @@ static u8 dm365_default_priorities[DAVINCI_N_AINTC_IRQ] = { [IRQ_I2C] = 3, [IRQ_UARTINT0] = 3, [IRQ_UARTINT1] = 3, + [IRQ_DM365_RTCINT] = 3, [IRQ_DM365_SPIINT0_0] = 3, [IRQ_DM365_SPIINT3_0] = 3, [IRQ_DM365_GPIO0] = 3, @@ -806,6 +810,50 @@ static struct platform_device dm365_edma_device = { .resource = edma_resources, }; +static struct resource dm365_asp_resources[] = { + { + .start = DAVINCI_DM365_ASP0_BASE, + .end = DAVINCI_DM365_ASP0_BASE + SZ_8K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = DAVINCI_DMA_ASP0_TX, + .end = DAVINCI_DMA_ASP0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = DAVINCI_DMA_ASP0_RX, + .end = DAVINCI_DMA_ASP0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device dm365_asp_device = { + .name = "davinci-asp", + .id = 0, + .num_resources = ARRAY_SIZE(dm365_asp_resources), + .resource = dm365_asp_resources, +}; + +static struct resource dm365_rtc_resources[] = { + { + .start = DM365_RTC_BASE, + .end = DM365_RTC_BASE + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_DM365_RTCINT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device dm365_rtc_device = { + .name = "rtc_davinci", + .id = 0, + .num_resources = ARRAY_SIZE(dm365_rtc_resources), + .resource = dm365_rtc_resources, +}; + static struct map_desc dm365_io_desc[] = { { .virtual = IO_VIRT, @@ -822,6 +870,28 @@ static struct map_desc dm365_io_desc[] = { }, }; +static struct resource dm365_ks_resources[] = { + { + /* registers */ + .start = DM365_KEYSCAN_BASE, + .end = DM365_KEYSCAN_BASE + SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + /* interrupt */ + .start = IRQ_DM365_KEYINT, + .end = IRQ_DM365_KEYINT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device dm365_ks_device = { + .name = "davinci_keyscan", + .id = 0, + .num_resources = ARRAY_SIZE(dm365_ks_resources), + .resource = dm365_ks_resources, +}; + /* Contents of JTAG ID register used to identify exact cpu type */ static struct davinci_id dm365_ids[] = { { @@ -907,6 +977,33 @@ static struct davinci_soc_info davinci_soc_info_dm365 = { .sram_len = SZ_32K, }; +void __init dm365_init_asp(struct snd_platform_data *pdata) +{ + davinci_cfg_reg(DM365_MCBSP0_BDX); + davinci_cfg_reg(DM365_MCBSP0_X); + davinci_cfg_reg(DM365_MCBSP0_BFSX); + davinci_cfg_reg(DM365_MCBSP0_BDR); + davinci_cfg_reg(DM365_MCBSP0_R); + davinci_cfg_reg(DM365_MCBSP0_BFSR); + davinci_cfg_reg(DM365_EVT2_ASP_TX); + davinci_cfg_reg(DM365_EVT3_ASP_RX); + dm365_asp_device.dev.platform_data = pdata; + platform_device_register(&dm365_asp_device); +} + +void __init dm365_init_ks(struct davinci_ks_platform_data *pdata) +{ + davinci_cfg_reg(DM365_KEYSCAN); + dm365_ks_device.dev.platform_data = pdata; + platform_device_register(&dm365_ks_device); +} + +void __init dm365_init_rtc(void) +{ + davinci_cfg_reg(DM365_INT_PRTCSS); + platform_device_register(&dm365_rtc_device); +} + void __init dm365_init(void) { davinci_common_init(&davinci_soc_info_dm365); diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index d6e0fa5a8d8..2cd008156de 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -8,7 +8,6 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/serial_8250.h> @@ -18,7 +17,6 @@ #include <asm/mach/map.h> #include <mach/dm644x.h> -#include <mach/clock.h> #include <mach/cputype.h> #include <mach/edma.h> #include <mach/irqs.h> @@ -370,6 +368,11 @@ MUX_CFG(DM644X, ATAEN_DISABLE, 0, 17, 1, 0, true) MUX_CFG(DM644X, HPIEN_DISABLE, 0, 29, 1, 0, true) MUX_CFG(DM644X, AEAW, 0, 0, 31, 31, true) +MUX_CFG(DM644X, AEAW0, 0, 0, 1, 0, true) +MUX_CFG(DM644X, AEAW1, 0, 1, 1, 0, true) +MUX_CFG(DM644X, AEAW2, 0, 2, 1, 0, true) +MUX_CFG(DM644X, AEAW3, 0, 3, 1, 0, true) +MUX_CFG(DM644X, AEAW4, 0, 4, 1, 0, true) MUX_CFG(DM644X, MSTK, 1, 9, 1, 0, false) diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 0976049c7b3..829a44bcf79 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -8,7 +8,6 @@ * is licensed "as is" without any warranty of any kind, whether express * or implied. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/clk.h> #include <linux/serial_8250.h> @@ -18,7 +17,6 @@ #include <asm/mach/map.h> #include <mach/dm646x.h> -#include <mach/clock.h> #include <mach/cputype.h> #include <mach/edma.h> #include <mach/irqs.h> @@ -789,7 +787,14 @@ static struct davinci_id dm646x_ids[] = { .part_no = 0xb770, .manufacturer = 0x017, .cpu_id = DAVINCI_CPU_ID_DM6467, - .name = "dm6467", + .name = "dm6467_rev1.x", + }, + { + .variant = 0x1, + .part_no = 0xb770, + .manufacturer = 0x017, + .cpu_id = DAVINCI_CPU_ID_DM6467, + .name = "dm6467_rev3.x", }, }; diff --git a/arch/arm/mach-davinci/dma.c b/arch/arm/mach-davinci/dma.c index f2e57d27295..648fbb760ae 100644 --- a/arch/arm/mach-davinci/dma.c +++ b/arch/arm/mach-davinci/dma.c @@ -18,22 +18,13 @@ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include <linux/kernel.h> -#include <linux/sched.h> #include <linux/init.h> #include <linux/module.h> #include <linux/interrupt.h> #include <linux/platform_device.h> -#include <linux/spinlock.h> -#include <linux/compiler.h> #include <linux/io.h> -#include <mach/cputype.h> -#include <mach/memory.h> -#include <mach/hardware.h> -#include <mach/irqs.h> #include <mach/edma.h> -#include <mach/mux.h> - /* Offsets matching "struct edmacc_param" */ #define PARM_OPT 0x00 @@ -509,43 +500,59 @@ static irqreturn_t dma_tc1err_handler(int irq, void *data) return IRQ_HANDLED; } -static int reserve_contiguous_params(int ctlr, unsigned int id, - unsigned int num_params, - unsigned int start_param) +static int reserve_contiguous_slots(int ctlr, unsigned int id, + unsigned int num_slots, + unsigned int start_slot) { int i, j; - unsigned int count = num_params; + unsigned int count = num_slots; + int stop_slot = start_slot; + DECLARE_BITMAP(tmp_inuse, EDMA_MAX_PARAMENTRY); - for (i = start_param; i < edma_info[ctlr]->num_slots; ++i) { + for (i = start_slot; i < edma_info[ctlr]->num_slots; ++i) { j = EDMA_CHAN_SLOT(i); - if (!test_and_set_bit(j, edma_info[ctlr]->edma_inuse)) + if (!test_and_set_bit(j, edma_info[ctlr]->edma_inuse)) { + /* Record our current beginning slot */ + if (count == num_slots) + stop_slot = i; + count--; + set_bit(j, tmp_inuse); + if (count == 0) break; - else if (id == EDMA_CONT_PARAMS_FIXED_EXACT) - break; - else - count = num_params; + } else { + clear_bit(j, tmp_inuse); + + if (id == EDMA_CONT_PARAMS_FIXED_EXACT) { + stop_slot = i; + break; + } else + count = num_slots; + } } /* * We have to clear any bits that we set - * if we run out parameter RAMs, i.e we do find a set - * of contiguous parameter RAMs but do not find the exact number - * requested as we may reach the total number of parameter RAMs + * if we run out parameter RAM slots, i.e we do find a set + * of contiguous parameter RAM slots but do not find the exact number + * requested as we may reach the total number of parameter RAM slots */ - if (count) { - for (j = i - num_params + count + 1; j <= i ; ++j) + if (i == edma_info[ctlr]->num_slots) + stop_slot = i; + + for (j = start_slot; j < stop_slot; j++) + if (test_bit(j, tmp_inuse)) clear_bit(j, edma_info[ctlr]->edma_inuse); + if (count) return -EBUSY; - } - for (j = i - num_params + 1; j <= i; ++j) + for (j = i - num_slots + 1; j <= i; ++j) memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(j), &dummy_paramset, PARM_SIZE); - return EDMA_CTLR_CHAN(ctlr, i - num_params + 1); + return EDMA_CTLR_CHAN(ctlr, i - num_slots + 1); } /*-----------------------------------------------------------------------*/ @@ -743,26 +750,27 @@ EXPORT_SYMBOL(edma_free_slot); /** * edma_alloc_cont_slots- alloc contiguous parameter RAM slots * The API will return the starting point of a set of - * contiguous PARAM's that have been requested + * contiguous parameter RAM slots that have been requested * * @id: can only be EDMA_CONT_PARAMS_ANY or EDMA_CONT_PARAMS_FIXED_EXACT * or EDMA_CONT_PARAMS_FIXED_NOT_EXACT - * @count: number of contiguous Paramter RAM's - * @param - the start value of Parameter RAM that should be passed if id + * @count: number of contiguous Paramter RAM slots + * @slot - the start value of Parameter RAM slot that should be passed if id * is EDMA_CONT_PARAMS_FIXED_EXACT or EDMA_CONT_PARAMS_FIXED_NOT_EXACT * * If id is EDMA_CONT_PARAMS_ANY then the API starts looking for a set of - * contiguous Parameter RAMs from parameter RAM 64 in the case of DaVinci SOCs - * and 32 in the case of Primus + * contiguous Parameter RAM slots from parameter RAM 64 in the case of + * DaVinci SOCs and 32 in the case of DA8xx SOCs. * * If id is EDMA_CONT_PARAMS_FIXED_EXACT then the API starts looking for a - * set of contiguous parameter RAMs from the "param" that is passed as an + * set of contiguous parameter RAM slots from the "slot" that is passed as an * argument to the API. * * If id is EDMA_CONT_PARAMS_FIXED_NOT_EXACT then the API initially tries - * starts looking for a set of contiguous parameter RAMs from the "param" + * starts looking for a set of contiguous parameter RAMs from the "slot" * that is passed as an argument to the API. On failure the API will try to - * find a set of contiguous Parameter RAMs in the remaining Parameter RAMs + * find a set of contiguous Parameter RAM slots from the remaining Parameter + * RAM slots */ int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count) { @@ -771,12 +779,13 @@ int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count) * the number of channels and lesser than the total number * of slots */ - if (slot < edma_info[ctlr]->num_channels || - slot >= edma_info[ctlr]->num_slots) + if ((id != EDMA_CONT_PARAMS_ANY) && + (slot < edma_info[ctlr]->num_channels || + slot >= edma_info[ctlr]->num_slots)) return -EINVAL; /* - * The number of parameter RAMs requested cannot be less than 1 + * The number of parameter RAM slots requested cannot be less than 1 * and cannot be more than the number of slots minus the number of * channels */ @@ -786,11 +795,11 @@ int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count) switch (id) { case EDMA_CONT_PARAMS_ANY: - return reserve_contiguous_params(ctlr, id, count, + return reserve_contiguous_slots(ctlr, id, count, edma_info[ctlr]->num_channels); case EDMA_CONT_PARAMS_FIXED_EXACT: case EDMA_CONT_PARAMS_FIXED_NOT_EXACT: - return reserve_contiguous_params(ctlr, id, count, slot); + return reserve_contiguous_slots(ctlr, id, count, slot); default: return -EINVAL; } @@ -799,21 +808,21 @@ int edma_alloc_cont_slots(unsigned ctlr, unsigned int id, int slot, int count) EXPORT_SYMBOL(edma_alloc_cont_slots); /** - * edma_free_cont_slots - deallocate DMA parameter RAMs - * @slot: first parameter RAM of a set of parameter RAMs to be freed - * @count: the number of contiguous parameter RAMs to be freed + * edma_free_cont_slots - deallocate DMA parameter RAM slots + * @slot: first parameter RAM of a set of parameter RAM slots to be freed + * @count: the number of contiguous parameter RAM slots to be freed * * This deallocates the parameter RAM slots allocated by * edma_alloc_cont_slots. * Callers/applications need to keep track of sets of contiguous - * parameter RAMs that have been allocated using the edma_alloc_cont_slots + * parameter RAM slots that have been allocated using the edma_alloc_cont_slots * API. * Callers are responsible for ensuring the slots are inactive, and will * not be activated. */ int edma_free_cont_slots(unsigned slot, int count) { - unsigned ctlr; + unsigned ctlr, slot_to_free; int i; ctlr = EDMA_CTLR(slot); @@ -826,11 +835,11 @@ int edma_free_cont_slots(unsigned slot, int count) for (i = slot; i < slot + count; ++i) { ctlr = EDMA_CTLR(i); - slot = EDMA_CHAN_SLOT(i); + slot_to_free = EDMA_CHAN_SLOT(i); - memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(slot), + memcpy_toio(edmacc_regs_base[ctlr] + PARM_OFFSET(slot_to_free), &dummy_paramset, PARM_SIZE); - clear_bit(slot, edma_info[ctlr]->edma_inuse); + clear_bit(slot_to_free, edma_info[ctlr]->edma_inuse); } return 0; diff --git a/arch/arm/mach-davinci/gpio.c b/arch/arm/mach-davinci/gpio.c index f6ea9db11f4..744755b5323 100644 --- a/arch/arm/mach-davinci/gpio.c +++ b/arch/arm/mach-davinci/gpio.c @@ -12,23 +12,14 @@ #include <linux/errno.h> #include <linux/kernel.h> -#include <linux/list.h> -#include <linux/module.h> #include <linux/clk.h> #include <linux/err.h> #include <linux/io.h> -#include <linux/irq.h> -#include <linux/bitops.h> -#include <mach/cputype.h> -#include <mach/irqs.h> -#include <mach/hardware.h> -#include <mach/common.h> #include <mach/gpio.h> #include <asm/mach/irq.h> - static DEFINE_SPINLOCK(gpio_lock); struct davinci_gpio { diff --git a/arch/arm/mach-davinci/include/mach/asp.h b/arch/arm/mach-davinci/include/mach/asp.h index 18e4ce34ece..834725f1e81 100644 --- a/arch/arm/mach-davinci/include/mach/asp.h +++ b/arch/arm/mach-davinci/include/mach/asp.h @@ -11,6 +11,9 @@ #define DAVINCI_ASP0_BASE 0x01E02000 #define DAVINCI_ASP1_BASE 0x01E04000 +/* Bases of dm365 register banks */ +#define DAVINCI_DM365_ASP0_BASE 0x01D02000 + /* Bases of dm646x register banks */ #define DAVINCI_DM646X_MCASP0_REG_BASE 0x01D01000 #define DAVINCI_DM646X_MCASP1_REG_BASE 0x01D01800 @@ -51,6 +54,14 @@ struct snd_platform_data { u32 rx_dma_offset; enum dma_event_q eventq_no; /* event queue number */ unsigned int codec_fmt; + /* + * Allowing this is more efficient and eliminates left and right swaps + * caused by underruns, but will swap the left and right channels + * when compared to previous behavior. + */ + unsigned enable_channel_combine:1; + unsigned sram_size_playback; + unsigned sram_size_capture; /* McASP specific fields */ int tdm_slots; diff --git a/arch/arm/mach-davinci/include/mach/common.h b/arch/arm/mach-davinci/include/mach/common.h index 1fd3917cae4..6ca2c9a0a48 100644 --- a/arch/arm/mach-davinci/include/mach/common.h +++ b/arch/arm/mach-davinci/include/mach/common.h @@ -20,12 +20,6 @@ extern void davinci_irq_init(void); extern void __iomem *davinci_intc_base; extern int davinci_intc_type; -/* parameters describe VBUS sourcing for host mode */ -extern void setup_usb(unsigned mA, unsigned potpgt_msec); - -/* parameters describe VBUS sourcing for host mode */ -extern void setup_usb(unsigned mA, unsigned potpgt_msec); - struct davinci_timer_instance { void __iomem *base; u32 bottom_irq; diff --git a/arch/arm/mach-davinci/include/mach/cpufreq.h b/arch/arm/mach-davinci/include/mach/cpufreq.h new file mode 100644 index 00000000000..3c089cfb6cd --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/cpufreq.h @@ -0,0 +1,26 @@ +/* + * TI DaVinci CPUFreq platform support. + * + * Copyright (C) 2009 Texas Instruments, Inc. http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#ifndef _MACH_DAVINCI_CPUFREQ_H +#define _MACH_DAVINCI_CPUFREQ_H + +#include <linux/cpufreq.h> + +struct davinci_cpufreq_config { + struct cpufreq_frequency_table *freq_table; + int (*set_voltage) (unsigned int index); + int (*init) (void); +}; + +#endif diff --git a/arch/arm/mach-davinci/include/mach/cpuidle.h b/arch/arm/mach-davinci/include/mach/cpuidle.h new file mode 100644 index 00000000000..cbfc6a9c81b --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/cpuidle.h @@ -0,0 +1,17 @@ +/* + * TI DaVinci cpuidle platform support + * + * 2009 (C) Texas Instruments, Inc. http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ +#ifndef _MACH_DAVINCI_CPUIDLE_H +#define _MACH_DAVINCI_CPUIDLE_H + +struct davinci_cpuidle_config { + u32 ddr2_pdown; +}; + +#endif diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index d4095d0572c..90704910d34 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -11,12 +11,17 @@ #ifndef __ASM_ARCH_DAVINCI_DA8XX_H #define __ASM_ARCH_DAVINCI_DA8XX_H +#include <video/da8xx-fb.h> + #include <mach/serial.h> #include <mach/edma.h> #include <mach/i2c.h> #include <mach/emac.h> #include <mach/asp.h> #include <mach/mmc.h> +#include <mach/usb.h> + +extern void __iomem *da8xx_syscfg_base; /* * The cp_intc interrupt controller for the da8xx isn't in the same @@ -29,11 +34,15 @@ #define DA8XX_CP_INTC_SIZE SZ_8K #define DA8XX_CP_INTC_VIRT (IO_VIRT - DA8XX_CP_INTC_SIZE - SZ_4K) -#define DA8XX_BOOT_CFG_BASE (IO_PHYS + 0x14000) +#define DA8XX_SYSCFG_BASE (IO_PHYS + 0x14000) +#define DA8XX_SYSCFG_VIRT(x) (da8xx_syscfg_base + (x)) +#define DA8XX_JTAG_ID_REG 0x18 +#define DA8XX_CFGCHIP0_REG 0x17c +#define DA8XX_CFGCHIP2_REG 0x184 +#define DA8XX_CFGCHIP3_REG 0x188 #define DA8XX_PSC0_BASE 0x01c10000 #define DA8XX_PLL0_BASE 0x01c11000 -#define DA8XX_JTAG_ID_REG 0x01c14018 #define DA8XX_TIMER64P0_BASE 0x01c20000 #define DA8XX_TIMER64P1_BASE 0x01c21000 #define DA8XX_GPIO_BASE 0x01e26000 @@ -43,6 +52,7 @@ #define DA8XX_AEMIF_CS2_BASE 0x60000000 #define DA8XX_AEMIF_CS3_BASE 0x62000000 #define DA8XX_AEMIF_CTL_BASE 0x68000000 +#define DA8XX_DDR2_CTL_BASE 0xb0000000 #define PINMUX0 0x00 #define PINMUX1 0x04 @@ -71,13 +81,20 @@ void __init da850_init(void); int da8xx_register_edma(void); int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata); int da8xx_register_watchdog(void); +int da8xx_register_usb20(unsigned mA, unsigned potpgt); +int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata); int da8xx_register_emac(void); -int da8xx_register_lcdc(void); +int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata); int da8xx_register_mmcsd0(struct davinci_mmc_config *config); -void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata); +void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata); +int da8xx_register_rtc(void); +int da850_register_cpufreq(void); +int da8xx_register_cpuidle(void); extern struct platform_device da8xx_serial_device; extern struct emac_platform_data da8xx_emac_pdata; +extern struct da8xx_lcdc_platform_data sharp_lcd035q3dg01_pdata; +extern struct da8xx_lcdc_platform_data sharp_lk043t1dg01_pdata; extern const short da830_emif25_pins[]; extern const short da830_spi0_pins[]; @@ -110,6 +127,7 @@ extern const short da850_uart2_pins[]; extern const short da850_i2c0_pins[]; extern const short da850_i2c1_pins[]; extern const short da850_cpgmac_pins[]; +extern const short da850_rmii_pins[]; extern const short da850_mcasp_pins[]; extern const short da850_lcdcntl_pins[]; extern const short da850_mmcsd0_pins[]; diff --git a/arch/arm/mach-davinci/include/mach/dm365.h b/arch/arm/mach-davinci/include/mach/dm365.h index 09db4343bb4..f1710a30e7b 100644 --- a/arch/arm/mach-davinci/include/mach/dm365.h +++ b/arch/arm/mach-davinci/include/mach/dm365.h @@ -16,6 +16,8 @@ #include <linux/platform_device.h> #include <mach/hardware.h> #include <mach/emac.h> +#include <mach/asp.h> +#include <mach/keyscan.h> #define DM365_EMAC_BASE (0x01D07000) #define DM365_EMAC_CNTRL_OFFSET (0x0000) @@ -24,6 +26,14 @@ #define DM365_EMAC_MDIO_OFFSET (0x4000) #define DM365_EMAC_CNTRL_RAM_SIZE (0x2000) +/* Base of key scan register bank */ +#define DM365_KEYSCAN_BASE (0x01C69400) + +#define DM365_RTC_BASE (0x01C69000) + void __init dm365_init(void); +void __init dm365_init_asp(struct snd_platform_data *pdata); +void __init dm365_init_ks(struct davinci_ks_platform_data *pdata); +void __init dm365_init_rtc(void); #endif /* __ASM_ARCH_DM365_H */ diff --git a/arch/arm/mach-davinci/include/mach/dm644x.h b/arch/arm/mach-davinci/include/mach/dm644x.h index 0efb73852c2..44e8f0fae9e 100644 --- a/arch/arm/mach-davinci/include/mach/dm644x.h +++ b/arch/arm/mach-davinci/include/mach/dm644x.h @@ -22,7 +22,6 @@ #ifndef __ASM_ARCH_DM644X_H #define __ASM_ARCH_DM644X_H -#include <linux/platform_device.h> #include <mach/hardware.h> #include <mach/emac.h> #include <mach/asp.h> diff --git a/arch/arm/mach-davinci/include/mach/irqs.h b/arch/arm/mach-davinci/include/mach/irqs.h index 3c918a77261..354af71798d 100644 --- a/arch/arm/mach-davinci/include/mach/irqs.h +++ b/arch/arm/mach-davinci/include/mach/irqs.h @@ -217,6 +217,7 @@ #define IRQ_DM365_SDIOINT0 23 #define IRQ_DM365_MMCINT1 27 #define IRQ_DM365_PWMINT3 28 +#define IRQ_DM365_RTCINT 29 #define IRQ_DM365_SDIOINT1 31 #define IRQ_DM365_SPIINT0_0 42 #define IRQ_DM365_SPIINT3_0 43 diff --git a/arch/arm/mach-davinci/include/mach/keyscan.h b/arch/arm/mach-davinci/include/mach/keyscan.h new file mode 100644 index 00000000000..b4e21a2976d --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/keyscan.h @@ -0,0 +1,41 @@ +/* + * Copyright (C) 2009 Texas Instruments, Inc + * + * Author: Miguel Aguilar <miguel.aguilar@ridgerun.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#ifndef DAVINCI_KEYSCAN_H +#define DAVINCI_KEYSCAN_H + +#include <linux/io.h> + +enum davinci_matrix_types { + DAVINCI_KEYSCAN_MATRIX_4X4, + DAVINCI_KEYSCAN_MATRIX_5X3, +}; + +struct davinci_ks_platform_data { + unsigned short *keymap; + u32 keymapsize; + u8 rep:1; + u8 strobe; + u8 interval; + u8 matrix_type; +}; + +#endif + diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h index bb84893a4e8..b60c693985f 100644 --- a/arch/arm/mach-davinci/include/mach/mux.h +++ b/arch/arm/mach-davinci/include/mach/mux.h @@ -40,6 +40,11 @@ enum davinci_dm644x_index { /* AEAW functions */ DM644X_AEAW, + DM644X_AEAW0, + DM644X_AEAW1, + DM644X_AEAW2, + DM644X_AEAW3, + DM644X_AEAW4, /* Memory Stick */ DM644X_MSTK, @@ -237,8 +242,8 @@ enum davinci_dm365_index { DM365_EMAC_MDIO, DM365_EMAC_MDCLK, - /* Keypad */ - DM365_KEYPAD, + /* Key Scan */ + DM365_KEYSCAN, /* PWM */ DM365_PWM0, @@ -774,6 +779,14 @@ enum davinci_da850_index { DA850_MII_RXD_0, DA850_MDIO_CLK, DA850_MDIO_D, + DA850_RMII_TXD_0, + DA850_RMII_TXD_1, + DA850_RMII_TXEN, + DA850_RMII_CRS_DV, + DA850_RMII_RXD_0, + DA850_RMII_RXD_1, + DA850_RMII_RXER, + DA850_RMII_MHZ_50_CLK, /* McASP function */ DA850_ACLKR, @@ -881,8 +894,9 @@ enum davinci_da850_index { DA850_NEMA_CS_2, /* GPIO function */ + DA850_GPIO2_6, + DA850_GPIO2_8, DA850_GPIO2_15, - DA850_GPIO8_10, DA850_GPIO4_0, DA850_GPIO4_1, }; diff --git a/arch/arm/mach-davinci/include/mach/system.h b/arch/arm/mach-davinci/include/mach/system.h index 8e4f10fe126..5a7d7581b8c 100644 --- a/arch/arm/mach-davinci/include/mach/system.h +++ b/arch/arm/mach-davinci/include/mach/system.h @@ -11,9 +11,6 @@ #ifndef __ASM_ARCH_SYSTEM_H #define __ASM_ARCH_SYSTEM_H -#include <linux/io.h> -#include <mach/hardware.h> - extern void davinci_watchdog_reset(void); static inline void arch_idle(void) diff --git a/arch/arm/mach-davinci/include/mach/usb.h b/arch/arm/mach-davinci/include/mach/usb.h new file mode 100644 index 00000000000..e0bc4abe69c --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/usb.h @@ -0,0 +1,59 @@ +/* + * USB related definitions + * + * Copyright (C) 2009 MontaVista Software, Inc. <source@mvista.com> + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +#ifndef __ASM_ARCH_USB_H +#define __ASM_ARCH_USB_H + +/* DA8xx CFGCHIP2 (USB 2.0 PHY Control) register bits */ +#define CFGCHIP2_PHYCLKGD (1 << 17) +#define CFGCHIP2_VBUSSENSE (1 << 16) +#define CFGCHIP2_RESET (1 << 15) +#define CFGCHIP2_OTGMODE (3 << 13) +#define CFGCHIP2_NO_OVERRIDE (0 << 13) +#define CFGCHIP2_FORCE_HOST (1 << 13) +#define CFGCHIP2_FORCE_DEVICE (2 << 13) +#define CFGCHIP2_FORCE_HOST_VBUS_LOW (3 << 13) +#define CFGCHIP2_USB1PHYCLKMUX (1 << 12) +#define CFGCHIP2_USB2PHYCLKMUX (1 << 11) +#define CFGCHIP2_PHYPWRDN (1 << 10) +#define CFGCHIP2_OTGPWRDN (1 << 9) +#define CFGCHIP2_DATPOL (1 << 8) +#define CFGCHIP2_USB1SUSPENDM (1 << 7) +#define CFGCHIP2_PHY_PLLON (1 << 6) /* override PLL suspend */ +#define CFGCHIP2_SESENDEN (1 << 5) /* Vsess_end comparator */ +#define CFGCHIP2_VBDTCTEN (1 << 4) /* Vbus comparator */ +#define CFGCHIP2_REFFREQ (0xf << 0) +#define CFGCHIP2_REFFREQ_12MHZ (1 << 0) +#define CFGCHIP2_REFFREQ_24MHZ (2 << 0) +#define CFGCHIP2_REFFREQ_48MHZ (3 << 0) + +struct da8xx_ohci_root_hub; + +typedef void (*da8xx_ocic_handler_t)(struct da8xx_ohci_root_hub *hub, + unsigned port); + +/* Passed as the platform data to the OHCI driver */ +struct da8xx_ohci_root_hub { + /* Switch the port power on/off */ + int (*set_power)(unsigned port, int on); + /* Read the port power status */ + int (*get_power)(unsigned port); + /* Read the port over-current indicator */ + int (*get_oci)(unsigned port); + /* Over-current indicator change notification (pass NULL to disable) */ + int (*ocic_notify)(da8xx_ocic_handler_t handler); + + /* Time from power on to power good (in 2 ms units) */ + u8 potpgt; +}; + +void davinci_setup_usb(unsigned mA, unsigned potpgt_ms); + +#endif /* ifndef __ASM_ARCH_USB_H */ diff --git a/arch/arm/mach-davinci/mux.c b/arch/arm/mach-davinci/mux.c index 898905e4894..f757e83415f 100644 --- a/arch/arm/mach-davinci/mux.c +++ b/arch/arm/mach-davinci/mux.c @@ -19,7 +19,6 @@ #include <linux/module.h> #include <linux/spinlock.h> -#include <mach/hardware.h> #include <mach/mux.h> #include <mach/common.h> diff --git a/arch/arm/mach-davinci/psc.c b/arch/arm/mach-davinci/psc.c index a78b657e916..04a3cb72c5a 100644 --- a/arch/arm/mach-davinci/psc.c +++ b/arch/arm/mach-davinci/psc.c @@ -19,14 +19,11 @@ * */ #include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> #include <linux/io.h> #include <mach/cputype.h> -#include <mach/hardware.h> #include <mach/psc.h> -#include <mach/mux.h> /* PSC register offsets */ #define EPCPR 0x070 diff --git a/arch/arm/mach-davinci/serial.c b/arch/arm/mach-davinci/serial.c index c530c7333d0..7ce5ba08657 100644 --- a/arch/arm/mach-davinci/serial.c +++ b/arch/arm/mach-davinci/serial.c @@ -28,14 +28,8 @@ #include <linux/clk.h> #include <linux/io.h> -#include <asm/irq.h> -#include <mach/hardware.h> #include <mach/serial.h> -#include <mach/irqs.h> #include <mach/cputype.h> -#include <mach/common.h> - -#include "clock.h" static inline unsigned int serial_read_reg(struct plat_serial8250_port *up, int offset) diff --git a/arch/arm/mach-davinci/sram.c b/arch/arm/mach-davinci/sram.c index 4f1fc9b318b..db0f7787faf 100644 --- a/arch/arm/mach-davinci/sram.c +++ b/arch/arm/mach-davinci/sram.c @@ -9,15 +9,12 @@ * (at your option) any later version. */ #include <linux/module.h> -#include <linux/kernel.h> #include <linux/init.h> #include <linux/genalloc.h> #include <mach/common.h> -#include <mach/memory.h> #include <mach/sram.h> - static struct gen_pool *sram_pool; void *sram_alloc(size_t len, dma_addr_t *dma) diff --git a/arch/arm/mach-davinci/time.c b/arch/arm/mach-davinci/time.c index 0d1b6d407b4..42d985beece 100644 --- a/arch/arm/mach-davinci/time.c +++ b/arch/arm/mach-davinci/time.c @@ -14,20 +14,14 @@ #include <linux/interrupt.h> #include <linux/clocksource.h> #include <linux/clockchips.h> -#include <linux/spinlock.h> #include <linux/io.h> #include <linux/clk.h> #include <linux/err.h> -#include <linux/device.h> #include <linux/platform_device.h> #include <mach/hardware.h> -#include <asm/system.h> -#include <asm/irq.h> #include <asm/mach/irq.h> #include <asm/mach/time.h> -#include <asm/errno.h> -#include <mach/io.h> #include <mach/cputype.h> #include <mach/time.h> #include "clock.h" diff --git a/arch/arm/mach-davinci/usb.c b/arch/arm/mach-davinci/usb.c index 06f55931620..31f0cbea0ca 100644 --- a/arch/arm/mach-davinci/usb.c +++ b/arch/arm/mach-davinci/usb.c @@ -1,21 +1,21 @@ /* * USB */ -#include <linux/kernel.h> -#include <linux/module.h> #include <linux/init.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/usb/musb.h> -#include <linux/usb/otg.h> #include <mach/common.h> -#include <mach/hardware.h> #include <mach/irqs.h> #include <mach/cputype.h> +#include <mach/usb.h> -#define DAVINCI_USB_OTG_BASE 0x01C64000 +#define DAVINCI_USB_OTG_BASE 0x01c64000 + +#define DA8XX_USB0_BASE 0x01e00000 +#define DA8XX_USB1_BASE 0x01e25000 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE) static struct musb_hdrc_eps_bits musb_eps[] = { @@ -85,10 +85,10 @@ static struct platform_device usb_dev = { .num_resources = ARRAY_SIZE(usb_resources), }; -void __init setup_usb(unsigned mA, unsigned potpgt_msec) +void __init davinci_setup_usb(unsigned mA, unsigned potpgt_ms) { - usb_data.power = mA / 2; - usb_data.potpgt = potpgt_msec / 2; + usb_data.power = mA > 510 ? 255 : mA / 2; + usb_data.potpgt = (potpgt_ms + 1) / 2; if (cpu_is_davinci_dm646x()) { /* Override the defaults as DM6467 uses different IRQs. */ @@ -100,11 +100,77 @@ void __init setup_usb(unsigned mA, unsigned potpgt_msec) platform_device_register(&usb_dev); } +#ifdef CONFIG_ARCH_DAVINCI_DA8XX +static struct resource da8xx_usb20_resources[] = { + { + .start = DA8XX_USB0_BASE, + .end = DA8XX_USB0_BASE + SZ_64K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_DA8XX_USB_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +int __init da8xx_register_usb20(unsigned mA, unsigned potpgt) +{ + usb_data.clock = "usb20"; + usb_data.power = mA > 510 ? 255 : mA / 2; + usb_data.potpgt = (potpgt + 1) / 2; + + usb_dev.resource = da8xx_usb20_resources; + usb_dev.num_resources = ARRAY_SIZE(da8xx_usb20_resources); + + return platform_device_register(&usb_dev); +} +#endif /* CONFIG_DAVINCI_DA8XX */ + #else -void __init setup_usb(unsigned mA, unsigned potpgt_msec) +void __init davinci_setup_usb(unsigned mA, unsigned potpgt_ms) { } +#ifdef CONFIG_ARCH_DAVINCI_DA8XX +int __init da8xx_register_usb20(unsigned mA, unsigned potpgt) +{ + return 0; +} +#endif + #endif /* CONFIG_USB_MUSB_HDRC */ +#ifdef CONFIG_ARCH_DAVINCI_DA8XX +static struct resource da8xx_usb11_resources[] = { + [0] = { + .start = DA8XX_USB1_BASE, + .end = DA8XX_USB1_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_DA8XX_IRQN, + .end = IRQ_DA8XX_IRQN, + .flags = IORESOURCE_IRQ, + }, +}; + +static u64 da8xx_usb11_dma_mask = DMA_BIT_MASK(32); + +static struct platform_device da8xx_usb11_device = { + .name = "ohci", + .id = 0, + .dev = { + .dma_mask = &da8xx_usb11_dma_mask, + .coherent_dma_mask = DMA_BIT_MASK(32), + }, + .num_resources = ARRAY_SIZE(da8xx_usb11_resources), + .resource = da8xx_usb11_resources, +}; + +int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata) +{ + da8xx_usb11_device.dev.platform_data = pdata; + return platform_device_register(&da8xx_usb11_device); +} +#endif /* CONFIG_DAVINCI_DA8XX */ |