15 files changed, 641 insertions, 278 deletions

diff --git a/arch/arm/mach-ep93xx/Kconfig b/arch/arm/mach-ep93xx/Kconfig
index 9167c3d2a5e..3a08b18f643 100644
--- a/arch/arm/mach-ep93xx/Kconfig
+++ b/arch/arm/mach-ep93xx/Kconfig
@@ -161,6 +161,20 @@ config MACH_MICRO9S
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-Slim board.
 
+config MACH_SIM_ONE
+        bool "Support Simplemachines Sim.One board"
+        depends on EP93XX_SDCE0_PHYS_OFFSET
+        help
+          Say 'Y' here if you want your kernel to support the
+          Simplemachines Sim.One board.
+
+config MACH_SNAPPER_CL15
+	bool "Support Bluewater Systems Snapper CL15 Module"
+	depends on EP93XX_SDCE0_PHYS_OFFSET
+	help
+	  Say 'Y' here if you want your kernel to support the Bluewater
+	  Systems Snapper CL15 Module.
+
 config MACH_TS72XX
 	bool "Support Technologic Systems TS-72xx SBC"
 	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
diff --git a/arch/arm/mach-ep93xx/Makefile b/arch/arm/mach-ep93xx/Makefile
index eae6199a989..33ee2c863d1 100644
--- a/arch/arm/mach-ep93xx/Makefile
+++ b/arch/arm/mach-ep93xx/Makefile
@@ -10,4 +10,6 @@ obj-$(CONFIG_MACH_ADSSPHERE)	+= adssphere.o
 obj-$(CONFIG_MACH_EDB93XX)	+= edb93xx.o
 obj-$(CONFIG_MACH_GESBC9312)	+= gesbc9312.o
 obj-$(CONFIG_MACH_MICRO9)	+= micro9.o
+obj-$(CONFIG_MACH_SIM_ONE)	+= simone.o
+obj-$(CONFIG_MACH_SNAPPER_CL15)	+= snappercl15.o
 obj-$(CONFIG_MACH_TS72XX)	+= ts72xx.o
diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index 1d0f9d8aff2..5f80092b6ac 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -10,6 +10,8 @@
  * your option) any later version.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
@@ -445,37 +447,39 @@ static void __init ep93xx_dma_clock_init(void)
 static int __init ep93xx_clock_init(void)
 {
 	u32 value;
-	int i;
 
-	value = __raw_readl(EP93XX_SYSCON_CLOCK_SET1);
-	if (!(value & 0x00800000)) {			/* PLL1 bypassed?  */
+	/* Determine the bootloader configured pll1 rate */
+	value = __raw_readl(EP93XX_SYSCON_CLKSET1);
+	if (!(value & EP93XX_SYSCON_CLKSET1_NBYP1))
 		clk_pll1.rate = clk_xtali.rate;
-	} else {
+	else
 		clk_pll1.rate = calc_pll_rate(value);
-	}
+
+	/* Initialize the pll1 derived clocks */
 	clk_f.rate = clk_pll1.rate / fclk_divisors[(value >> 25) & 0x7];
 	clk_h.rate = clk_pll1.rate / hclk_divisors[(value >> 20) & 0x7];
 	clk_p.rate = clk_h.rate / pclk_divisors[(value >> 18) & 0x3];
 	ep93xx_dma_clock_init();
 
-	value = __raw_readl(EP93XX_SYSCON_CLOCK_SET2);
-	if (!(value & 0x00080000)) {			/* PLL2 bypassed?  */
+	/* Determine the bootloader configured pll2 rate */
+	value = __raw_readl(EP93XX_SYSCON_CLKSET2);
+	if (!(value & EP93XX_SYSCON_CLKSET2_NBYP2))
 		clk_pll2.rate = clk_xtali.rate;
-	} else if (value & 0x00040000) {		/* PLL2 enabled?  */
+	else if (value & EP93XX_SYSCON_CLKSET2_PLL2_EN)
 		clk_pll2.rate = calc_pll_rate(value);
-	} else {
+	else
 		clk_pll2.rate = 0;
-	}
+
+	/* Initialize the pll2 derived clocks */
 	clk_usb_host.rate = clk_pll2.rate / (((value >> 28) & 0xf) + 1);
 
-	printk(KERN_INFO "ep93xx: PLL1 running at %ld MHz, PLL2 at %ld MHz\n",
+	pr_info("PLL1 running at %ld MHz, PLL2 at %ld MHz\n",
 		clk_pll1.rate / 1000000, clk_pll2.rate / 1000000);
-	printk(KERN_INFO "ep93xx: FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n",
+	pr_info("FCLK %ld MHz, HCLK %ld MHz, PCLK %ld MHz\n",
 		clk_f.rate / 1000000, clk_h.rate / 1000000,
 		clk_p.rate / 1000000);
 
-	for (i = 0; i < ARRAY_SIZE(clocks); i++)
-		clkdev_add(&clocks[i]);
+	clkdev_add_table(clocks, ARRAY_SIZE(clocks));
 	return 0;
 }
 arch_initcall(ep93xx_clock_init);
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 1f0d66561bb..90fb591cbff 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -14,12 +14,15 @@
  * your option) any later version.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
 #include <linux/dma-mapping.h>
 #include <linux/timex.h>
+#include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
@@ -35,7 +38,6 @@
 
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
-#include <asm/mach/irq.h>
 
 #include <asm/hardware/vic.h>
 
@@ -82,13 +84,40 @@ void __init ep93xx_map_io(void)
  * to use this timer for something else.  We also use timer 4 for keeping
  * track of lost jiffies.
  */
-static unsigned int last_jiffy_time;
-
+#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
+#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
+#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
+#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
+#define EP93XX_TIMER123_CONTROL_ENABLE	(1 << 7)
+#define EP93XX_TIMER123_CONTROL_MODE	(1 << 6)
+#define EP93XX_TIMER123_CONTROL_CLKSEL	(1 << 3)
+#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
+#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
+#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
+#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
+#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
+#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
+#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
+#define EP93XX_TIMER4_VALUE_HIGH_ENABLE	(1 << 8)
+#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
+#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
+#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
+#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
+
+#define EP93XX_TIMER123_CLOCK		508469
+#define EP93XX_TIMER4_CLOCK		983040
+
+#define TIMER1_RELOAD			((EP93XX_TIMER123_CLOCK / HZ) - 1)
 #define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
 
+static unsigned int last_jiffy_time;
+
 static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
 {
+	/* Writing any value clears the timer interrupt */
 	__raw_writel(1, EP93XX_TIMER1_CLEAR);
+
+	/* Recover lost jiffies */
 	while ((signed long)
 		(__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time)
 						>= TIMER4_TICKS_PER_JIFFY) {
@@ -107,13 +136,18 @@ static struct irqaction ep93xx_timer_irq = {
 
 static void __init ep93xx_timer_init(void)
 {
+	u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
+		    EP93XX_TIMER123_CONTROL_CLKSEL;
+
 	/* Enable periodic HZ timer.  */
-	__raw_writel(0x48, EP93XX_TIMER1_CONTROL);
-	__raw_writel((508469 / HZ) - 1, EP93XX_TIMER1_LOAD);
-	__raw_writel(0xc8, EP93XX_TIMER1_CONTROL);
+	__raw_writel(tmode, EP93XX_TIMER1_CONTROL);
+	__raw_writel(TIMER1_RELOAD, EP93XX_TIMER1_LOAD);
+	__raw_writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
+			EP93XX_TIMER1_CONTROL);
 
 	/* Enable lost jiffy timer.  */
-	__raw_writel(0x100, EP93XX_TIMER4_VALUE_HIGH);
+	__raw_writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
+			EP93XX_TIMER4_VALUE_HIGH);
 
 	setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq);
 }
@@ -135,237 +169,16 @@ struct sys_timer ep93xx_timer = {
 
 
 /*************************************************************************
- * GPIO handling for EP93xx
- *************************************************************************/
-static unsigned char gpio_int_unmasked[3];
-static unsigned char gpio_int_enabled[3];
-static unsigned char gpio_int_type1[3];
-static unsigned char gpio_int_type2[3];
-static unsigned char gpio_int_debounce[3];
-
-/* Port ordering is: A B F */
-static const u8 int_type1_register_offset[3]	= { 0x90, 0xac, 0x4c };
-static const u8 int_type2_register_offset[3]	= { 0x94, 0xb0, 0x50 };
-static const u8 eoi_register_offset[3]		= { 0x98, 0xb4, 0x54 };
-static const u8 int_en_register_offset[3]	= { 0x9c, 0xb8, 0x58 };
-static const u8 int_debounce_register_offset[3]	= { 0xa8, 0xc4, 0x64 };
-
-void ep93xx_gpio_update_int_params(unsigned port)
-{
-	BUG_ON(port > 2);
-
-	__raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
-
-	__raw_writeb(gpio_int_type2[port],
-		EP93XX_GPIO_REG(int_type2_register_offset[port]));
-
-	__raw_writeb(gpio_int_type1[port],
-		EP93XX_GPIO_REG(int_type1_register_offset[port]));
-
-	__raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
-		EP93XX_GPIO_REG(int_en_register_offset[port]));
-}
-
-void ep93xx_gpio_int_mask(unsigned line)
-{
-	gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
-}
-
-void ep93xx_gpio_int_debounce(unsigned int irq, int enable)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if (enable)
-		gpio_int_debounce[port] |= port_mask;
-	else
-		gpio_int_debounce[port] &= ~port_mask;
-
-	__raw_writeb(gpio_int_debounce[port],
-		EP93XX_GPIO_REG(int_debounce_register_offset[port]));
-}
-EXPORT_SYMBOL(ep93xx_gpio_int_debounce);
-
-/*************************************************************************
  * EP93xx IRQ handling
  *************************************************************************/
-static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned char status;
-	int i;
-
-	status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
-	for (i = 0; i < 8; i++) {
-		if (status & (1 << i)) {
-			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
-			generic_handle_irq(gpio_irq);
-		}
-	}
-
-	status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
-	for (i = 0; i < 8; i++) {
-		if (status & (1 << i)) {
-			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
-			generic_handle_irq(gpio_irq);
-		}
-	}
-}
-
-static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	/*
-	 * map discontiguous hw irq range to continous sw irq range:
-	 *
-	 *  IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
-	 */
-	int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
-	int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
-
-	generic_handle_irq(gpio_irq);
-}
-
-static void ep93xx_gpio_irq_ack(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
-		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
-		ep93xx_gpio_update_int_params(port);
-	}
-
-	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-	int port_mask = 1 << (line & 7);
-
-	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
-		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
-
-	gpio_int_unmasked[port] &= ~port_mask;
-	ep93xx_gpio_update_int_params(port);
-
-	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-
-	gpio_int_unmasked[port] &= ~(1 << (line & 7));
-	ep93xx_gpio_update_int_params(port);
-}
-
-static void ep93xx_gpio_irq_unmask(unsigned int irq)
-{
-	int line = irq_to_gpio(irq);
-	int port = line >> 3;
-
-	gpio_int_unmasked[port] |= 1 << (line & 7);
-	ep93xx_gpio_update_int_params(port);
-}
-
-
-/*
- * gpio_int_type1 controls whether the interrupt is level (0) or
- * edge (1) triggered, while gpio_int_type2 controls whether it
- * triggers on low/falling (0) or high/rising (1).
- */
-static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
-{
-	struct irq_desc *desc = irq_desc + irq;
-	const int gpio = irq_to_gpio(irq);
-	const int port = gpio >> 3;
-	const int port_mask = 1 << (gpio & 7);
-
-	gpio_direction_input(gpio);
-
-	switch (type) {
-	case IRQ_TYPE_EDGE_RISING:
-		gpio_int_type1[port] |= port_mask;
-		gpio_int_type2[port] |= port_mask;
-		desc->handle_irq = handle_edge_irq;
-		break;
-	case IRQ_TYPE_EDGE_FALLING:
-		gpio_int_type1[port] |= port_mask;
-		gpio_int_type2[port] &= ~port_mask;
-		desc->handle_irq = handle_edge_irq;
-		break;
-	case IRQ_TYPE_LEVEL_HIGH:
-		gpio_int_type1[port] &= ~port_mask;
-		gpio_int_type2[port] |= port_mask;
-		desc->handle_irq = handle_level_irq;
-		break;
-	case IRQ_TYPE_LEVEL_LOW:
-		gpio_int_type1[port] &= ~port_mask;
-		gpio_int_type2[port] &= ~port_mask;
-		desc->handle_irq = handle_level_irq;
-		break;
-	case IRQ_TYPE_EDGE_BOTH:
-		gpio_int_type1[port] |= port_mask;
-		/* set initial polarity based on current input level */
-		if (gpio_get_value(gpio))
-			gpio_int_type2[port] &= ~port_mask; /* falling */
-		else
-			gpio_int_type2[port] |= port_mask; /* rising */
-		desc->handle_irq = handle_edge_irq;
-		break;
-	default:
-		pr_err("ep93xx: failed to set irq type %d for gpio %d\n",
-		       type, gpio);
-		return -EINVAL;
-	}
-
-	gpio_int_enabled[port] |= port_mask;
-
-	desc->status &= ~IRQ_TYPE_SENSE_MASK;
-	desc->status |= type & IRQ_TYPE_SENSE_MASK;
-
-	ep93xx_gpio_update_int_params(port);
-
-	return 0;
-}
-
-static struct irq_chip ep93xx_gpio_irq_chip = {
-	.name		= "GPIO",
-	.ack		= ep93xx_gpio_irq_ack,
-	.mask_ack	= ep93xx_gpio_irq_mask_ack,
-	.mask		= ep93xx_gpio_irq_mask,
-	.unmask		= ep93xx_gpio_irq_unmask,
-	.set_type	= ep93xx_gpio_irq_type,
-};
-
+extern void ep93xx_gpio_init_irq(void);
 
 void __init ep93xx_init_irq(void)
 {
-	int gpio_irq;
-
 	vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
 	vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
 
-	for (gpio_irq = gpio_to_irq(0);
-	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
-		set_irq_chip(gpio_irq, &ep93xx_gpio_irq_chip);
-		set_irq_handler(gpio_irq, handle_level_irq);
-		set_irq_flags(gpio_irq, IRQF_VALID);
-	}
-
-	set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
-	set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
+	ep93xx_gpio_init_irq();
 }
 
 
@@ -572,9 +385,9 @@ void __init ep93xx_register_i2c(struct i2c_gpio_platform_data *data,
 	 * CMOS driver.
 	 */
 	if (data->sda_is_open_drain && data->sda_pin != EP93XX_GPIO_LINE_EEDAT)
-		pr_warning("ep93xx: sda != EEDAT, open drain has no effect\n");
+		pr_warning("sda != EEDAT, open drain has no effect\n");
 	if (data->scl_is_open_drain && data->scl_pin != EP93XX_GPIO_LINE_EECLK)
-		pr_warning("ep93xx: scl != EECLK, open drain has no effect\n");
+		pr_warning("scl != EECLK, open drain has no effect\n");
 
 	__raw_writel((data->sda_is_open_drain << 1) |
 		     (data->scl_is_open_drain << 0),
diff --git a/arch/arm/mach-ep93xx/dma-m2p.c b/arch/arm/mach-ep93xx/dma-m2p.c
index dbcac9c40a2..8904ca4e2e2 100644
--- a/arch/arm/mach-ep93xx/dma-m2p.c
+++ b/arch/arm/mach-ep93xx/dma-m2p.c
@@ -28,6 +28,8 @@
  * with this implementation.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/err.h>
@@ -173,7 +175,7 @@ static irqreturn_t m2p_irq(int irq, void *dev_id)
 
 	switch (m2p_channel_state(ch)) {
 	case STATE_IDLE:
-		pr_crit("m2p_irq: dma interrupt without a dma buffer\n");
+		pr_crit("dma interrupt without a dma buffer\n");
 		BUG();
 		break;
 
@@ -197,7 +199,7 @@ static irqreturn_t m2p_irq(int irq, void *dev_id)
 		break;
 
 	case STATE_NEXT:
-		pr_crit("m2p_irq: dma interrupt while next\n");
+		pr_crit("dma interrupt while next\n");
 		BUG();
 		break;
 	}
diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index a4a7be30800..d22d67ac8b9 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -118,12 +118,33 @@ static void __init edb93xx_register_i2c(void)
 	}
 }
 
+
+/*************************************************************************
+ * EDB93xx pwm
+ *************************************************************************/
+static void __init edb93xx_register_pwm(void)
+{
+	if (machine_is_edb9301() ||
+	    machine_is_edb9302() || machine_is_edb9302a()) {
+		/* EP9301 and EP9302 only have pwm.1 (EGPIO14) */
+		ep93xx_register_pwm(0, 1);
+	} else if (machine_is_edb9307() || machine_is_edb9307a()) {
+		/* EP9307 only has pwm.0 (PWMOUT) */
+		ep93xx_register_pwm(1, 0);
+	} else {
+		/* EP9312 and EP9315 have both */
+		ep93xx_register_pwm(1, 1);
+	}
+}
+
+
 static void __init edb93xx_init_machine(void)
 {
 	ep93xx_init_devices();
 	edb93xx_register_flash();
 	ep93xx_register_eth(&edb93xx_eth_data, 1);
 	edb93xx_register_i2c();
+	edb93xx_register_pwm();
 }
 
 
diff --git a/arch/arm/mach-ep93xx/gpio.c b/arch/arm/mach-ep93xx/gpio.c
index 1ea8871e03a..cc377ae8c42 100644
--- a/arch/arm/mach-ep93xx/gpio.c
+++ b/arch/arm/mach-ep93xx/gpio.c
@@ -13,6 +13,8 @@
  *  published by the Free Software Foundation.
  */
 
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/seq_file.h>
@@ -22,6 +24,235 @@
 
 #include <mach/hardware.h>
 
+/*************************************************************************
+ * GPIO handling for EP93xx
+ *************************************************************************/
+static unsigned char gpio_int_unmasked[3];
+static unsigned char gpio_int_enabled[3];
+static unsigned char gpio_int_type1[3];
+static unsigned char gpio_int_type2[3];
+static unsigned char gpio_int_debounce[3];
+
+/* Port ordering is: A B F */
+static const u8 int_type1_register_offset[3]	= { 0x90, 0xac, 0x4c };
+static const u8 int_type2_register_offset[3]	= { 0x94, 0xb0, 0x50 };
+static const u8 eoi_register_offset[3]		= { 0x98, 0xb4, 0x54 };
+static const u8 int_en_register_offset[3]	= { 0x9c, 0xb8, 0x58 };
+static const u8 int_debounce_register_offset[3]	= { 0xa8, 0xc4, 0x64 };
+
+void ep93xx_gpio_update_int_params(unsigned port)
+{
+	BUG_ON(port > 2);
+
+	__raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
+
+	__raw_writeb(gpio_int_type2[port],
+		EP93XX_GPIO_REG(int_type2_register_offset[port]));
+
+	__raw_writeb(gpio_int_type1[port],
+		EP93XX_GPIO_REG(int_type1_register_offset[port]));
+
+	__raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
+		EP93XX_GPIO_REG(int_en_register_offset[port]));
+}
+
+void ep93xx_gpio_int_mask(unsigned line)
+{
+	gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
+}
+
+void ep93xx_gpio_int_debounce(unsigned int irq, int enable)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if (enable)
+		gpio_int_debounce[port] |= port_mask;
+	else
+		gpio_int_debounce[port] &= ~port_mask;
+
+	__raw_writeb(gpio_int_debounce[port],
+		EP93XX_GPIO_REG(int_debounce_register_offset[port]));
+}
+EXPORT_SYMBOL(ep93xx_gpio_int_debounce);
+
+static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	unsigned char status;
+	int i;
+
+	status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+
+	status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
+	for (i = 0; i < 8; i++) {
+		if (status & (1 << i)) {
+			int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
+			generic_handle_irq(gpio_irq);
+		}
+	}
+}
+
+static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	/*
+	 * map discontiguous hw irq range to continous sw irq range:
+	 *
+	 *  IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
+	 */
+	int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
+	int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
+
+	generic_handle_irq(gpio_irq);
+}
+
+static void ep93xx_gpio_irq_ack(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+		ep93xx_gpio_update_int_params(port);
+	}
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+	int port_mask = 1 << (line & 7);
+
+	if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
+		gpio_int_type2[port] ^= port_mask; /* switch edge direction */
+
+	gpio_int_unmasked[port] &= ~port_mask;
+	ep93xx_gpio_update_int_params(port);
+
+	__raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
+}
+
+static void ep93xx_gpio_irq_mask(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] &= ~(1 << (line & 7));
+	ep93xx_gpio_update_int_params(port);
+}
+
+static void ep93xx_gpio_irq_unmask(unsigned int irq)
+{
+	int line = irq_to_gpio(irq);
+	int port = line >> 3;
+
+	gpio_int_unmasked[port] |= 1 << (line & 7);
+	ep93xx_gpio_update_int_params(port);
+}
+
+/*
+ * gpio_int_type1 controls whether the interrupt is level (0) or
+ * edge (1) triggered, while gpio_int_type2 controls whether it
+ * triggers on low/falling (0) or high/rising (1).
+ */
+static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
+{
+	struct irq_desc *desc = irq_desc + irq;
+	const int gpio = irq_to_gpio(irq);
+	const int port = gpio >> 3;
+	const int port_mask = 1 << (gpio & 7);
+
+	gpio_direction_input(gpio);
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] |= port_mask;
+		desc->handle_irq = handle_edge_irq;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		gpio_int_type1[port] |= port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		desc->handle_irq = handle_edge_irq;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] |= port_mask;
+		desc->handle_irq = handle_level_irq;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		gpio_int_type1[port] &= ~port_mask;
+		gpio_int_type2[port] &= ~port_mask;
+		desc->handle_irq = handle_level_irq;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		gpio_int_type1[port] |= port_mask;
+		/* set initial polarity based on current input level */
+		if (gpio_get_value(gpio))
+			gpio_int_type2[port] &= ~port_mask; /* falling */
+		else
+			gpio_int_type2[port] |= port_mask; /* rising */
+		desc->handle_irq = handle_edge_irq;
+		break;
+	default:
+		pr_err("failed to set irq type %d for gpio %d\n", type, gpio);
+		return -EINVAL;
+	}
+
+	gpio_int_enabled[port] |= port_mask;
+
+	desc->status &= ~IRQ_TYPE_SENSE_MASK;
+	desc->status |= type & IRQ_TYPE_SENSE_MASK;
+
+	ep93xx_gpio_update_int_params(port);
+
+	return 0;
+}
+
+static struct irq_chip ep93xx_gpio_irq_chip = {
+	.name		= "GPIO",
+	.ack		= ep93xx_gpio_irq_ack,
+	.mask_ack	= ep93xx_gpio_irq_mask_ack,
+	.mask		= ep93xx_gpio_irq_mask,
+	.unmask		= ep93xx_gpio_irq_unmask,
+	.set_type	= ep93xx_gpio_irq_type,
+};
+
+void __init ep93xx_gpio_init_irq(void)
+{
+	int gpio_irq;
+
+	for (gpio_irq = gpio_to_irq(0);
+	     gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
+		set_irq_chip(gpio_irq, &ep93xx_gpio_irq_chip);
+		set_irq_handler(gpio_irq, handle_level_irq);
+		set_irq_flags(gpio_irq, IRQF_VALID);
+	}
+
+	set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
+	set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
+}
+
+
+/*************************************************************************
+ * gpiolib interface for EP93xx on-chip GPIOs
+ *************************************************************************/
 struct ep93xx_gpio_chip {
 	struct gpio_chip	chip;
 
@@ -31,10 +262,6 @@ struct ep93xx_gpio_chip {
 
 #define to_ep93xx_gpio_chip(c) container_of(c, struct ep93xx_gpio_chip, chip)
 
-/* From core.c */
-extern void ep93xx_gpio_int_mask(unsigned line);
-extern void ep93xx_gpio_update_int_params(unsigned port);
-
 static int ep93xx_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
 	struct ep93xx_gpio_chip *ep93xx_chip = to_ep93xx_gpio_chip(chip);
diff --git a/arch/arm/mach-ep93xx/include/mach/debug-macro.S b/arch/arm/mach-ep93xx/include/mach/debug-macro.S
index 802858bc809..5cd22444e22 100644
--- a/arch/arm/mach-ep93xx/include/mach/debug-macro.S
+++ b/arch/arm/mach-ep93xx/include/mach/debug-macro.S
@@ -11,7 +11,7 @@
  */
 #include <mach/ep93xx-regs.h>
 
-		.macro	addruart,rx
+		.macro	addruart, rx, tmp
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1				@ MMU enabled?
 		ldreq	\rx, =EP93XX_APB_PHYS_BASE	@ Physical base
diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
index d55194a4c09..93e2ecc79ce 100644
--- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
@@ -92,21 +92,6 @@
 
 /* APB peripherals */
 #define EP93XX_TIMER_BASE		EP93XX_APB_IOMEM(0x00010000)
-#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
-#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
-#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
-#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
-#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
-#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
-#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
-#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
-#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
-#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
-#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
-#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
-#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
-#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
-#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
 
 #define EP93XX_I2S_BASE			EP93XX_APB_IOMEM(0x00020000)
 
@@ -167,8 +152,11 @@
 #define EP93XX_SYSCON_PWRCNT_DMA_M2P1	(1<<16)
 #define EP93XX_SYSCON_HALT		EP93XX_SYSCON_REG(0x08)
 #define EP93XX_SYSCON_STANDBY		EP93XX_SYSCON_REG(0x0c)
-#define EP93XX_SYSCON_CLOCK_SET1	EP93XX_SYSCON_REG(0x20)
-#define EP93XX_SYSCON_CLOCK_SET2	EP93XX_SYSCON_REG(0x24)
+#define EP93XX_SYSCON_CLKSET1		EP93XX_SYSCON_REG(0x20)
+#define EP93XX_SYSCON_CLKSET1_NBYP1	(1<<23)
+#define EP93XX_SYSCON_CLKSET2		EP93XX_SYSCON_REG(0x24)
+#define EP93XX_SYSCON_CLKSET2_NBYP2	(1<<19)
+#define EP93XX_SYSCON_CLKSET2_PLL2_EN	(1<<18)
 #define EP93XX_SYSCON_DEVCFG		EP93XX_SYSCON_REG(0x80)
 #define EP93XX_SYSCON_DEVCFG_SWRST	(1<<31)
 #define EP93XX_SYSCON_DEVCFG_D1ONG	(1<<30)
diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h b/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h
index 62d17421e48..1e2f4e97f42 100644
--- a/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h
+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx_keypad.h
@@ -5,6 +5,8 @@
 #ifndef __ASM_ARCH_EP93XX_KEYPAD_H
 #define __ASM_ARCH_EP93XX_KEYPAD_H
 
+struct matrix_keymap_data;
+
 /* flags for the ep93xx_keypad driver */
 #define EP93XX_KEYPAD_DISABLE_3_KEY	(1<<0)	/* disable 3-key reset */
 #define EP93XX_KEYPAD_DIAG_MODE		(1<<1)	/* diagnostic mode */
@@ -15,15 +17,13 @@
 
 /**
  * struct ep93xx_keypad_platform_data - platform specific device structure
- * @matrix_key_map:		array of keycodes defining the keypad matrix
- * @matrix_key_map_size:	ARRAY_SIZE(matrix_key_map)
- * @debounce:			debounce start count; terminal count is 0xff
- * @prescale:			row/column counter pre-scaler load value
- * @flags:			see above
+ * @keymap_data:	pointer to &matrix_keymap_data
+ * @debounce:		debounce start count; terminal count is 0xff
+ * @prescale:		row/column counter pre-scaler load value
+ * @flags:		see above
  */
 struct ep93xx_keypad_platform_data {
-	unsigned int	*matrix_key_map;
-	int		matrix_key_map_size;
+	struct matrix_keymap_data *keymap_data;
 	unsigned int	debounce;
 	unsigned int	prescale;
 	unsigned int	flags;
diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
index 3bd934e9a7f..93107d88ff3 100644
--- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h
+++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
@@ -65,6 +65,8 @@
 #define TS72XX_RTC_DATA_PHYS_BASE	0x11700000
 #define TS72XX_RTC_DATA_SIZE		0x00001000
 
+#define TS72XX_WDT_CONTROL_PHYS_BASE	0x23800000
+#define TS72XX_WDT_FEED_PHYS_BASE	0x23c00000
 
 #ifndef __ASSEMBLY__
 
diff --git a/arch/arm/mach-ep93xx/include/mach/vmalloc.h b/arch/arm/mach-ep93xx/include/mach/vmalloc.h
index aed21cd3fe2..1b3f25d03d3 100644
--- a/arch/arm/mach-ep93xx/include/mach/vmalloc.h
+++ b/arch/arm/mach-ep93xx/include/mach/vmalloc.h
@@ -2,4 +2,4 @@
  * arch/arm/mach-ep93xx/include/mach/vmalloc.h
  */
 
-#define VMALLOC_END	0xfe800000
+#define VMALLOC_END	0xfe800000UL
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
new file mode 100644
index 00000000000..cd93990f1b9
--- /dev/null
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -0,0 +1,97 @@
+/*
+ * arch/arm/mach-ep93xx/simone.c
+ * Simplemachines Sim.One support.
+ *
+ * Copyright (C) 2010 Ryan Mallon <ryan@bluewatersys.com>
+ *
+ * Based on the 2.6.24.7 support:
+ *   Copyright (C) 2009 Simplemachines
+ *   MMC support by Peter Ivanov <ivanovp@gmail.com>, 2007
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+static struct physmap_flash_data simone_flash_data = {
+	.width		= 2,
+};
+
+static struct resource simone_flash_resource = {
+	.start		= EP93XX_CS6_PHYS_BASE,
+	.end		= EP93XX_CS6_PHYS_BASE + SZ_8M - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device simone_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.num_resources	= 1,
+	.resource	= &simone_flash_resource,
+	.dev = {
+		.platform_data	= &simone_flash_data,
+	},
+};
+
+static struct ep93xx_eth_data simone_eth_data = {
+	.phy_id		= 1,
+};
+
+static struct ep93xxfb_mach_info simone_fb_info = {
+	.num_modes	= EP93XXFB_USE_MODEDB,
+	.bpp		= 16,
+	.flags		= EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
+};
+
+static struct i2c_gpio_platform_data simone_i2c_gpio_data = {
+	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
+	.sda_is_open_drain	= 0,
+	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
+	.scl_is_open_drain	= 0,
+	.udelay			= 0,
+	.timeout		= 0,
+};
+
+static struct i2c_board_info __initdata simone_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("ds1337", 0x68),
+	},
+};
+
+static void __init simone_init_machine(void)
+{
+	ep93xx_init_devices();
+
+	platform_device_register(&simone_flash);
+	ep93xx_register_eth(&simone_eth_data, 1);
+	ep93xx_register_fb(&simone_fb_info);
+	ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info,
+			    ARRAY_SIZE(simone_i2c_board_info));
+}
+
+MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
+/* Maintainer: Ryan Mallon <ryan@bluewatersys.com> */
+	.phys_io	= EP93XX_APB_PHYS_BASE,
+	.io_pg_offst	= ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.map_io		= ep93xx_map_io,
+	.init_irq	= ep93xx_init_irq,
+	.timer		= &ep93xx_timer,
+	.init_machine	= simone_init_machine,
+MACHINE_END
diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c
new file mode 100644
index 00000000000..51134b0382c
--- /dev/null
+++ b/arch/arm/mach-ep93xx/snappercl15.c
@@ -0,0 +1,172 @@
+/*
+ * arch/arm/mach-ep93xx/snappercl15.c
+ * Bluewater Systems Snapper CL15 system module
+ *
+ * Copyright (C) 2009 Bluewater Systems Ltd
+ * Author: Ryan Mallon <ryan@bluewatersys.com>
+ *
+ * NAND code adapted from driver by:
+ *   Andre Renaud <andre@bluewatersys.com>
+ *   James R. McKaskill
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/fb.h>
+
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#define SNAPPERCL15_NAND_BASE	(EP93XX_CS7_PHYS_BASE + SZ_16M)
+
+#define SNAPPERCL15_NAND_WPN	(1 << 8)  /* Write protect (active low) */
+#define SNAPPERCL15_NAND_ALE	(1 << 9)  /* Address latch */
+#define SNAPPERCL15_NAND_CLE	(1 << 10) /* Command latch */
+#define SNAPPERCL15_NAND_CEN	(1 << 11) /* Chip enable (active low) */
+#define SNAPPERCL15_NAND_RDY	(1 << 14) /* Device ready */
+
+#define NAND_CTRL_ADDR(chip) 	(chip->IO_ADDR_W + 0x40)
+
+static void snappercl15_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+				      unsigned int ctrl)
+{
+	struct nand_chip *chip = mtd->priv;
+	static u16 nand_state = SNAPPERCL15_NAND_WPN;
+	u16 set;
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		set = SNAPPERCL15_NAND_CEN | SNAPPERCL15_NAND_WPN;
+
+		if (ctrl & NAND_NCE)
+			set &= ~SNAPPERCL15_NAND_CEN;
+		if (ctrl & NAND_CLE)
+			set |= SNAPPERCL15_NAND_CLE;
+		if (ctrl & NAND_ALE)
+			set |= SNAPPERCL15_NAND_ALE;
+
+		nand_state &= ~(SNAPPERCL15_NAND_CEN |
+				SNAPPERCL15_NAND_CLE |
+				SNAPPERCL15_NAND_ALE);
+		nand_state |= set;
+		__raw_writew(nand_state, NAND_CTRL_ADDR(chip));
+	}
+
+	if (cmd != NAND_CMD_NONE)
+		__raw_writew((cmd & 0xff) | nand_state, chip->IO_ADDR_W);
+}
+
+static int snappercl15_nand_dev_ready(struct mtd_info *mtd)
+{
+	struct nand_chip *chip = mtd->priv;
+
+	return !!(__raw_readw(NAND_CTRL_ADDR(chip)) & SNAPPERCL15_NAND_RDY);
+}
+
+static const char *snappercl15_nand_part_probes[] = {"cmdlinepart", NULL};
+
+static struct mtd_partition snappercl15_nand_parts[] = {
+	{
+		.name		= "Kernel",
+		.offset		= 0,
+		.size		= SZ_2M,
+	},
+	{
+		.name		= "Filesystem",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct platform_nand_data snappercl15_nand_data = {
+	.chip = {
+		.nr_chips		= 1,
+		.part_probe_types	= snappercl15_nand_part_probes,
+		.partitions		= snappercl15_nand_parts,
+		.nr_partitions		= ARRAY_SIZE(snappercl15_nand_parts),
+		.options		= NAND_NO_AUTOINCR,
+		.chip_delay		= 25,
+	},
+	.ctrl = {
+		.dev_ready		= snappercl15_nand_dev_ready,
+		.cmd_ctrl		= snappercl15_nand_cmd_ctrl,
+	},
+};
+
+static struct resource snappercl15_nand_resource[] = {
+	{
+		.start		= SNAPPERCL15_NAND_BASE,
+		.end		= SNAPPERCL15_NAND_BASE + SZ_4K - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device snappercl15_nand_device = {
+	.name			= "gen_nand",
+	.id			= -1,
+	.dev.platform_data	= &snappercl15_nand_data,
+	.resource		= snappercl15_nand_resource,
+	.num_resources		= ARRAY_SIZE(snappercl15_nand_resource),
+};
+
+static struct ep93xx_eth_data snappercl15_eth_data = {
+	.phy_id			= 1,
+};
+
+static struct i2c_gpio_platform_data snappercl15_i2c_gpio_data = {
+	.sda_pin		= EP93XX_GPIO_LINE_EEDAT,
+	.sda_is_open_drain	= 0,
+	.scl_pin		= EP93XX_GPIO_LINE_EECLK,
+	.scl_is_open_drain	= 0,
+	.udelay			= 0,
+	.timeout		= 0,
+};
+
+static struct i2c_board_info __initdata snappercl15_i2c_data[] = {
+	{
+		/* Audio codec */
+		I2C_BOARD_INFO("tlv320aic23", 0x1a),
+	},
+};
+
+static struct ep93xxfb_mach_info snappercl15_fb_info = {
+	.num_modes		= EP93XXFB_USE_MODEDB,
+	.bpp			= 16,
+};
+
+static void __init snappercl15_init_machine(void)
+{
+	ep93xx_init_devices();
+	ep93xx_register_eth(&snappercl15_eth_data, 1);
+	ep93xx_register_i2c(&snappercl15_i2c_gpio_data, snappercl15_i2c_data,
+			    ARRAY_SIZE(snappercl15_i2c_data));
+	ep93xx_register_fb(&snappercl15_fb_info);
+	platform_device_register(&snappercl15_nand_device);
+}
+
+MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
+	/* Maintainer: Ryan Mallon <ryan@bluewatersys.com> */
+	.phys_io	= EP93XX_APB_PHYS_BASE,
+	.io_pg_offst	= ((EP93XX_APB_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= EP93XX_SDCE0_PHYS_BASE + 0x100,
+	.map_io		= ep93xx_map_io,
+	.init_irq	= ep93xx_init_irq,
+	.timer 		= &ep93xx_timer,
+	.init_machine	= snappercl15_init_machine,
+MACHINE_END
diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c
index 259f7822ba5..fac1ec7a60f 100644
--- a/arch/arm/mach-ep93xx/ts72xx.c
+++ b/arch/arm/mach-ep93xx/ts72xx.c
@@ -166,6 +166,26 @@ static struct platform_device ts72xx_rtc_device = {
 	.num_resources	= 0,
 };
 
+static struct resource ts72xx_wdt_resources[] = {
+	{
+		.start	= TS72XX_WDT_CONTROL_PHYS_BASE,
+		.end	= TS72XX_WDT_CONTROL_PHYS_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= TS72XX_WDT_FEED_PHYS_BASE,
+		.end	= TS72XX_WDT_FEED_PHYS_BASE + SZ_4K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device ts72xx_wdt_device = {
+	.name		= "ts72xx-wdt",
+	.id		= -1,
+	.num_resources 	= ARRAY_SIZE(ts72xx_wdt_resources),
+	.resource	= ts72xx_wdt_resources,
+};
+
 static struct ep93xx_eth_data ts72xx_eth_data = {
 	.phy_id		= 1,
 };
@@ -175,6 +195,7 @@ static void __init ts72xx_init_machine(void)
 	ep93xx_init_devices();
 	ts72xx_register_flash();
 	platform_device_register(&ts72xx_rtc_device);
+	platform_device_register(&ts72xx_wdt_device);
 
 	ep93xx_register_eth(&ts72xx_eth_data, 1);
 }