diff options
Diffstat (limited to 'arch/arm/mach-imx/mach-mx31lilly.c')
| -rw-r--r-- | arch/arm/mach-imx/mach-mx31lilly.c | 302 |
1 files changed, 302 insertions, 0 deletions
diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c new file mode 100644 index 00000000000..410e676ae08 --- /dev/null +++ b/arch/arm/mach-imx/mach-mx31lilly.c @@ -0,0 +1,302 @@ +/* + * LILLY-1131 module support + * + * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de> + * + * based on code for other MX31 boards, + * + * Copyright 2005-2007 Freescale Semiconductor + * Copyright (c) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com> + * Copyright (C) 2009 Valentin Longchamp, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/gpio.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/interrupt.h> +#include <linux/smsc911x.h> +#include <linux/mtd/physmap.h> +#include <linux/spi/spi.h> +#include <linux/mfd/mc13783.h> +#include <linux/usb/otg.h> +#include <linux/usb/ulpi.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/mach/map.h> + +#include <mach/hardware.h> +#include <mach/common.h> +#include <mach/iomux-mx3.h> +#include <mach/board-mx31lilly.h> +#include <mach/ulpi.h> + +#include "devices-imx31.h" + +/* + * This file contains module-specific initialization routines for LILLY-1131. + * Initialization of peripherals found on the baseboard is implemented in the + * appropriate baseboard support code. + */ + +/* SMSC ethernet support */ + +static struct resource smsc91x_resources[] = { + { + .start = MX31_CS4_BASE_ADDR, + .end = MX31_CS4_BASE_ADDR + 0xffff, + .flags = IORESOURCE_MEM, + }, + { + .start = IOMUX_TO_IRQ(MX31_PIN_GPIO1_0), + .end = IOMUX_TO_IRQ(MX31_PIN_GPIO1_0), + .flags = IORESOURCE_IRQ | IRQF_TRIGGER_FALLING, + } +}; + +static struct smsc911x_platform_config smsc911x_config = { + .phy_interface = PHY_INTERFACE_MODE_MII, + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .flags = SMSC911X_USE_32BIT | + SMSC911X_SAVE_MAC_ADDRESS | + SMSC911X_FORCE_INTERNAL_PHY, +}; + +static struct platform_device smsc91x_device = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smsc91x_resources), + .resource = smsc91x_resources, + .dev = { + .platform_data = &smsc911x_config, + } +}; + +/* NOR flash */ +static struct physmap_flash_data nor_flash_data = { + .width = 2, +}; + +static struct resource nor_flash_resource = { + .start = 0xa0000000, + .end = 0xa1ffffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device physmap_flash_device = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &nor_flash_data, + }, + .resource = &nor_flash_resource, + .num_resources = 1, +}; + +/* USB */ + +#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \ + PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU) + +static int usbh1_init(struct platform_device *pdev) +{ + int pins[] = { + MX31_PIN_CSPI1_MOSI__USBH1_RXDM, + MX31_PIN_CSPI1_MISO__USBH1_RXDP, + MX31_PIN_CSPI1_SS0__USBH1_TXDM, + MX31_PIN_CSPI1_SS1__USBH1_TXDP, + MX31_PIN_CSPI1_SS2__USBH1_RCV, + MX31_PIN_CSPI1_SCLK__USBH1_OEB, + MX31_PIN_CSPI1_SPI_RDY__USBH1_FS, + }; + + mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H1"); + + mxc_iomux_set_pad(MX31_PIN_CSPI1_MOSI, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_MISO, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_SS0, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_SS1, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_SS2, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_SCLK, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_CSPI1_SPI_RDY, USB_PAD_CFG); + + mxc_iomux_set_gpr(MUX_PGP_USB_SUSPEND, true); + + mdelay(10); + + return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED | + MXC_EHCI_INTERFACE_SINGLE_UNI); +} + +static int usbh2_init(struct platform_device *pdev) +{ + int pins[] = { + MX31_PIN_USBH2_DATA0__USBH2_DATA0, + MX31_PIN_USBH2_DATA1__USBH2_DATA1, + MX31_PIN_USBH2_CLK__USBH2_CLK, + MX31_PIN_USBH2_DIR__USBH2_DIR, + MX31_PIN_USBH2_NXT__USBH2_NXT, + MX31_PIN_USBH2_STP__USBH2_STP, + }; + + mxc_iomux_setup_multiple_pins(pins, ARRAY_SIZE(pins), "USB H2"); + + mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG); + mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG); + + mxc_iomux_set_gpr(MUX_PGP_UH2, true); + + /* chip select */ + mxc_iomux_alloc_pin(IOMUX_MODE(MX31_PIN_DTR_DCE1, IOMUX_CONFIG_GPIO), + "USBH2_CS"); + gpio_request(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), "USBH2 CS"); + gpio_direction_output(IOMUX_TO_GPIO(MX31_PIN_DTR_DCE1), 0); + + mdelay(10); + + return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED); +} + +static const struct mxc_usbh_platform_data usbh1_pdata __initconst = { + .init = usbh1_init, + .portsc = MXC_EHCI_MODE_UTMI | MXC_EHCI_SERIAL, +}; + +static struct mxc_usbh_platform_data usbh2_pdata __initdata = { + .init = usbh2_init, + .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT, +}; + +static void lilly1131_usb_init(void) +{ + imx31_add_mxc_ehci_hs(1, &usbh1_pdata); + + usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS | + ULPI_OTG_DRVVBUS_EXT); + if (usbh2_pdata.otg) + imx31_add_mxc_ehci_hs(2, &usbh2_pdata); +} + +/* SPI */ + +static int spi_internal_chipselect[] = { + MXC_SPI_CS(0), + MXC_SPI_CS(1), + MXC_SPI_CS(2), +}; + +static const struct spi_imx_master spi0_pdata __initconst = { + .chipselect = spi_internal_chipselect, + .num_chipselect = ARRAY_SIZE(spi_internal_chipselect), +}; + +static const struct spi_imx_master spi1_pdata __initconst = { + .chipselect = spi_internal_chipselect, + .num_chipselect = ARRAY_SIZE(spi_internal_chipselect), +}; + +static struct mc13xxx_platform_data mc13783_pdata __initdata = { + .flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN, +}; + +static struct spi_board_info mc13783_dev __initdata = { + .modalias = "mc13783", + .max_speed_hz = 1000000, + .bus_num = 1, + .chip_select = 0, + .platform_data = &mc13783_pdata, + .irq = IOMUX_TO_IRQ(MX31_PIN_GPIO1_3), +}; + +static struct platform_device *devices[] __initdata = { + &smsc91x_device, + &physmap_flash_device, +}; + +static int mx31lilly_baseboard; +core_param(mx31lilly_baseboard, mx31lilly_baseboard, int, 0444); + +static void __init mx31lilly_board_init(void) +{ + switch (mx31lilly_baseboard) { + case MX31LILLY_NOBOARD: + break; + case MX31LILLY_DB: + mx31lilly_db_init(); + break; + default: + printk(KERN_ERR "Illegal mx31lilly_baseboard type %d\n", + mx31lilly_baseboard); + } + + mxc_iomux_alloc_pin(MX31_PIN_CS4__CS4, "Ethernet CS"); + + /* SPI */ + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SCLK__SCLK, "SPI1_CLK"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MOSI__MOSI, "SPI1_TX"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_MISO__MISO, "SPI1_RX"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, "SPI1_RDY"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS0__SS0, "SPI1_SS0"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS1__SS1, "SPI1_SS1"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI1_SS2__SS2, "SPI1_SS2"); + + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SCLK__SCLK, "SPI2_CLK"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MOSI__MOSI, "SPI2_TX"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_MISO__MISO, "SPI2_RX"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SPI_RDY__SPI_RDY, "SPI2_RDY"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS0__SS0, "SPI2_SS0"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS1__SS1, "SPI2_SS1"); + mxc_iomux_alloc_pin(MX31_PIN_CSPI2_SS2__SS2, "SPI2_SS2"); + + imx31_add_spi_imx0(&spi0_pdata); + imx31_add_spi_imx1(&spi1_pdata); + spi_register_board_info(&mc13783_dev, 1); + + platform_add_devices(devices, ARRAY_SIZE(devices)); + + /* USB */ + lilly1131_usb_init(); +} + +static void __init mx31lilly_timer_init(void) +{ + mx31_clocks_init(26000000); +} + +static struct sys_timer mx31lilly_timer = { + .init = mx31lilly_timer_init, +}; + +MACHINE_START(LILLY1131, "INCO startec LILLY-1131") + .boot_params = MX3x_PHYS_OFFSET + 0x100, + .map_io = mx31_map_io, + .init_early = imx31_init_early, + .init_irq = mx31_init_irq, + .timer = &mx31lilly_timer, + .init_machine = mx31lilly_board_init, +MACHINE_END |