diff options
Diffstat (limited to 'arch/arm/mach-integrator/platsmp.c')
| -rw-r--r-- | arch/arm/mach-integrator/platsmp.c | 204 |
1 files changed, 0 insertions, 204 deletions
diff --git a/arch/arm/mach-integrator/platsmp.c b/arch/arm/mach-integrator/platsmp.c deleted file mode 100644 index 613b841a10f..00000000000 --- a/arch/arm/mach-integrator/platsmp.c +++ /dev/null @@ -1,204 +0,0 @@ -/* - * linux/arch/arm/mach-cintegrator/platsmp.c - * - * Copyright (C) 2002 ARM Ltd. - * All Rights Reserved - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/init.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/errno.h> -#include <linux/mm.h> - -#include <asm/atomic.h> -#include <asm/cacheflush.h> -#include <asm/delay.h> -#include <asm/mmu_context.h> -#include <asm/ptrace.h> -#include <asm/smp.h> - -extern void integrator_secondary_startup(void); - -/* - * control for which core is the next to come out of the secondary - * boot "holding pen" - */ -volatile int __cpuinitdata pen_release = -1; -unsigned long __cpuinitdata phys_pen_release = 0; - -static DEFINE_SPINLOCK(boot_lock); - -void __cpuinit platform_secondary_init(unsigned int cpu) -{ - /* - * the primary core may have used a "cross call" soft interrupt - * to get this processor out of WFI in the BootMonitor - make - * sure that we are no longer being sent this soft interrupt - */ - smp_cross_call_done(cpumask_of_cpu(cpu)); - - /* - * if any interrupts are already enabled for the primary - * core (e.g. timer irq), then they will not have been enabled - * for us: do so - */ - secondary_scan_irqs(); - - /* - * let the primary processor know we're out of the - * pen, then head off into the C entry point - */ - pen_release = -1; - - /* - * Synchronise with the boot thread. - */ - spin_lock(&boot_lock); - spin_unlock(&boot_lock); -} - -int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) -{ - unsigned long timeout; - - /* - * set synchronisation state between this boot processor - * and the secondary one - */ - spin_lock(&boot_lock); - - /* - * The secondary processor is waiting to be released from - * the holding pen - release it, then wait for it to flag - * that it has been released by resetting pen_release. - * - * Note that "pen_release" is the hardware CPU ID, whereas - * "cpu" is Linux's internal ID. - */ - pen_release = cpu; - flush_cache_all(); - - /* - * XXX - * - * This is a later addition to the booting protocol: the - * bootMonitor now puts secondary cores into WFI, so - * poke_milo() no longer gets the cores moving; we need - * to send a soft interrupt to wake the secondary core. - * Use smp_cross_call() for this, since there's little - * point duplicating the code here - */ - smp_cross_call(cpumask_of_cpu(cpu)); - - timeout = jiffies + (1 * HZ); - while (time_before(jiffies, timeout)) { - if (pen_release == -1) - break; - - udelay(10); - } - - /* - * now the secondary core is starting up let it run its - * calibrations, then wait for it to finish - */ - spin_unlock(&boot_lock); - - return pen_release != -1 ? -ENOSYS : 0; -} - -static void __init poke_milo(void) -{ - extern void secondary_startup(void); - - /* nobody is to be released from the pen yet */ - pen_release = -1; - - phys_pen_release = virt_to_phys(&pen_release); - - /* - * write the address of secondary startup into the system-wide - * flags register, then clear the bottom two bits, which is what - * BootMonitor is waiting for - */ -#if 1 -#define CINTEGRATOR_HDR_FLAGSS_OFFSET 0x30 - __raw_writel(virt_to_phys(integrator_secondary_startup), - (IO_ADDRESS(INTEGRATOR_HDR_BASE) + - CINTEGRATOR_HDR_FLAGSS_OFFSET)); -#define CINTEGRATOR_HDR_FLAGSC_OFFSET 0x34 - __raw_writel(3, - (IO_ADDRESS(INTEGRATOR_HDR_BASE) + - CINTEGRATOR_HDR_FLAGSC_OFFSET)); -#endif - - mb(); -} - -/* - * Initialise the CPU possible map early - this describes the CPUs - * which may be present or become present in the system. - */ -void __init smp_init_cpus(void) -{ - unsigned int i, ncores = get_core_count(); - - for (i = 0; i < ncores; i++) - cpu_set(i, cpu_possible_map); -} - -void __init smp_prepare_cpus(unsigned int max_cpus) -{ - unsigned int ncores = get_core_count(); - unsigned int cpu = smp_processor_id(); - int i; - - /* sanity check */ - if (ncores == 0) { - printk(KERN_ERR - "Integrator/CP: strange CM count of 0? Default to 1\n"); - - ncores = 1; - } - - if (ncores > NR_CPUS) { - printk(KERN_WARNING - "Integrator/CP: no. of cores (%d) greater than configured " - "maximum of %d - clipping\n", - ncores, NR_CPUS); - ncores = NR_CPUS; - } - - /* - * start with some more config for the Boot CPU, now that - * the world is a bit more alive (which was not the case - * when smp_prepare_boot_cpu() was called) - */ - smp_store_cpu_info(cpu); - - /* - * are we trying to boot more cores than exist? - */ - if (max_cpus > ncores) - max_cpus = ncores; - - /* - * Initialise the present map, which describes the set of CPUs - * actually populated at the present time. - */ - for (i = 0; i < max_cpus; i++) - cpu_set(i, cpu_present_map); - - /* - * Do we need any more CPUs? If so, then let them know where - * to start. Note that, on modern versions of MILO, the "poke" - * doesn't actually do anything until each individual core is - * sent a soft interrupt to get it out of WFI - */ - if (max_cpus > 1) - poke_milo(); -} |