diff options
Diffstat (limited to 'arch/arm/mach-ixp4xx/dsmg600-setup.c')
| -rw-r--r-- | arch/arm/mach-ixp4xx/dsmg600-setup.c | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c new file mode 100644 index 00000000000..1caff65e22c --- /dev/null +++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c @@ -0,0 +1,175 @@ +/* + * DSM-G600 board-setup + * + * Copyright (C) 2006 Tower Technologies + * Author: Alessandro Zummo <a.zummo@towertech.it> + * + * based ixdp425-setup.c: + * Copyright (C) 2003-2004 MontaVista Software, Inc. + * + * Author: Alessandro Zummo <a.zummo@towertech.it> + * Maintainers: http://www.nslu2-linux.org/ + */ + +#include <linux/kernel.h> +#include <linux/serial.h> +#include <linux/serial_8250.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/flash.h> + +static struct flash_platform_data dsmg600_flash_data = { + .map_name = "cfi_probe", + .width = 2, +}; + +static struct resource dsmg600_flash_resource = { + .flags = IORESOURCE_MEM, +}; + +static struct platform_device dsmg600_flash = { + .name = "IXP4XX-Flash", + .id = 0, + .dev.platform_data = &dsmg600_flash_data, + .num_resources = 1, + .resource = &dsmg600_flash_resource, +}; + +static struct ixp4xx_i2c_pins dsmg600_i2c_gpio_pins = { + .sda_pin = DSMG600_SDA_PIN, + .scl_pin = DSMG600_SCL_PIN, +}; + +static struct platform_device dsmg600_i2c_controller = { + .name = "IXP4XX-I2C", + .id = 0, + .dev.platform_data = &dsmg600_i2c_gpio_pins, +}; + +#ifdef CONFIG_LEDS_CLASS +static struct resource dsmg600_led_resources[] = { + { + .name = "power", + .start = DSMG600_LED_PWR_GPIO, + .end = DSMG600_LED_PWR_GPIO, + .flags = IXP4XX_GPIO_HIGH, + }, + { + .name = "wlan", + .start = DSMG600_LED_WLAN_GPIO, + .end = DSMG600_LED_WLAN_GPIO, + .flags = IXP4XX_GPIO_LOW, + }, +}; + +static struct platform_device dsmg600_leds = { + .name = "IXP4XX-GPIO-LED", + .id = -1, + .num_resources = ARRAY_SIZE(dsmg600_led_resources), + .resource = dsmg600_led_resources, +}; +#endif + +static struct resource dsmg600_uart_resources[] = { + { + .start = IXP4XX_UART1_BASE_PHYS, + .end = IXP4XX_UART1_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + }, + { + .start = IXP4XX_UART2_BASE_PHYS, + .end = IXP4XX_UART2_BASE_PHYS + 0x0fff, + .flags = IORESOURCE_MEM, + } +}; + +static struct plat_serial8250_port dsmg600_uart_data[] = { + { + .mapbase = IXP4XX_UART1_BASE_PHYS, + .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART1, + .flags = UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { + .mapbase = IXP4XX_UART2_BASE_PHYS, + .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET, + .irq = IRQ_IXP4XX_UART2, + .flags = UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 2, + .uartclk = IXP4XX_UART_XTAL, + }, + { } +}; + +static struct platform_device dsmg600_uart = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev.platform_data = dsmg600_uart_data, + .num_resources = ARRAY_SIZE(dsmg600_uart_resources), + .resource = dsmg600_uart_resources, +}; + +static struct platform_device *dsmg600_devices[] __initdata = { + &dsmg600_i2c_controller, + &dsmg600_flash, +}; + +static void dsmg600_power_off(void) +{ + /* enable the pwr cntl gpio */ + gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT); + + /* poweroff */ + gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH); +} + +static void __init dsmg600_init(void) +{ + ixp4xx_sys_init(); + + /* Make sure that GPIO14 and GPIO15 are not used as clocks */ + *IXP4XX_GPIO_GPCLKR = 0; + + dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0); + dsmg600_flash_resource.end = + IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1; + + pm_power_off = dsmg600_power_off; + + /* The UART is required on the DSM-G600 (Redboot cannot use the + * NIC) -- do it here so that it does *not* get removed if + * platform_add_devices fails! + */ + (void)platform_device_register(&dsmg600_uart); + + platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices)); + +#ifdef CONFIG_LEDS_CLASS + /* We don't care whether or not this works. */ + (void)platform_device_register(&dsmg600_leds); +#endif +} + +static void __init dsmg600_fixup(struct machine_desc *desc, + struct tag *tags, char **cmdline, struct meminfo *mi) +{ + /* The xtal on this machine is non-standard. */ + ixp4xx_timer_freq = DSMG600_FREQ; +} + +MACHINE_START(DSMG600, "D-Link DSM-G600 RevA") + /* Maintainer: www.nslu2-linux.org */ + .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS, + .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC, + .boot_params = 0x00000100, + .fixup = dsmg600_fixup, + .map_io = ixp4xx_map_io, + .init_irq = ixp4xx_init_irq, + .timer = &ixp4xx_timer, + .init_machine = dsmg600_init, +MACHINE_END |