1 files changed, 134 insertions, 0 deletions
diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c
new file mode 100644
index 00000000000..289e94cb65c
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/nslu2-setup.c
@@ -0,0 +1,134 @@
+/*
+ * arch/arm/mach-ixp4xx/nslu2-setup.c
+ *
+ * NSLU2 board-setup
+ *
+ * based ixdp425-setup.c:
+ *      Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ * Author: Mark Rakes <mrakes at mac.com>
+ * Maintainers: http://www.nslu2-linux.org/
+ *
+ * Fixed missing init_time in MACHINE_START kas11 10/22/04
+ * Changed to conform to new style __init ixdp425 kas11 10/22/04
+ */
+
+#include <linux/kernel.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data nslu2_flash_data = {
+	.map_name		= "cfi_probe",
+	.width			= 2,
+};
+
+static struct resource nslu2_flash_resource = {
+	.start			= NSLU2_FLASH_BASE,
+	.end			= NSLU2_FLASH_BASE + NSLU2_FLASH_SIZE,
+	.flags			= IORESOURCE_MEM,
+};
+
+static struct platform_device nslu2_flash = {
+	.name			= "IXP4XX-Flash",
+	.id			= 0,
+	.dev.platform_data	= &nslu2_flash_data,
+	.num_resources		= 1,
+	.resource		= &nslu2_flash_resource,
+};
+
+static struct ixp4xx_i2c_pins nslu2_i2c_gpio_pins = {
+	.sda_pin		= NSLU2_SDA_PIN,
+	.scl_pin		= NSLU2_SCL_PIN,
+};
+
+static struct platform_device nslu2_i2c_controller = {
+	.name			= "IXP4XX-I2C",
+	.id			= 0,
+	.dev.platform_data	= &nslu2_i2c_gpio_pins,
+	.num_resources		= 0,
+};
+
+static struct resource nslu2_uart_resources[] = {
+	{
+		.start		= IXP4XX_UART1_BASE_PHYS,
+		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= IXP4XX_UART2_BASE_PHYS,
+		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
+		.flags		= IORESOURCE_MEM,
+	}
+};
+
+static struct plat_serial8250_port nslu2_uart_data[] = {
+	{
+		.mapbase	= IXP4XX_UART1_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART1,
+		.flags		= UPF_BOOT_AUTOCONF,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{
+		.mapbase	= IXP4XX_UART2_BASE_PHYS,
+		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+		.irq		= IRQ_IXP4XX_UART2,
+		.flags		= UPF_BOOT_AUTOCONF,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= IXP4XX_UART_XTAL,
+	},
+	{ }
+};
+
+static struct platform_device nslu2_uart = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev.platform_data	= nslu2_uart_data,
+	.num_resources		= 2,
+	.resource		= nslu2_uart_resources,
+};
+
+static struct platform_device *nslu2_devices[] __initdata = {
+	&nslu2_i2c_controller,
+	&nslu2_flash,
+	&nslu2_uart,
+};
+
+static void nslu2_power_off(void)
+{
+	/* This causes the box to drop the power and go dead. */
+
+	/* enable the pwr cntl gpio */
+	gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
+
+	/* do the deed */
+	gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
+}
+
+static void __init nslu2_init(void)
+{
+	ixp4xx_sys_init();
+
+	pm_power_off = nslu2_power_off;
+
+	platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
+}
+
+MACHINE_START(NSLU2, "Linksys NSLU2")
+	/* Maintainer: www.nslu2-linux.org */
+	.phys_ram	= PHYS_OFFSET,
+	.phys_io	= IXP4XX_PERIPHERAL_BASE_PHYS,
+	.io_pg_offst	= ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+	.boot_params	= 0x00000100,
+	.map_io		= ixp4xx_map_io,
+	.init_irq	= ixp4xx_init_irq,
+	.timer          = &ixp4xx_timer,
+	.init_machine	= nslu2_init,
+MACHINE_END