diff options
Diffstat (limited to 'arch/arm/mach-kirkwood/sheevaplug-setup.c')
| -rw-r--r-- | arch/arm/mach-kirkwood/sheevaplug-setup.c | 50 |
1 files changed, 48 insertions, 2 deletions
diff --git a/arch/arm/mach-kirkwood/sheevaplug-setup.c b/arch/arm/mach-kirkwood/sheevaplug-setup.c index c7319eeac8b..a00879d34d5 100644 --- a/arch/arm/mach-kirkwood/sheevaplug-setup.c +++ b/arch/arm/mach-kirkwood/sheevaplug-setup.c @@ -11,6 +11,7 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> +#include <linux/ata_platform.h> #include <linux/mtd/partitions.h> #include <linux/mv643xx_eth.h> #include <linux/gpio.h> @@ -42,10 +43,19 @@ static struct mv643xx_eth_platform_data sheevaplug_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; +static struct mv_sata_platform_data sheeva_esata_sata_data = { + .n_ports = 2, +}; + static struct mvsdio_platform_data sheevaplug_mvsdio_data = { /* unfortunately the CD signal has not been connected */ }; +static struct mvsdio_platform_data sheeva_esata_mvsdio_data = { + .gpio_write_protect = 44, /* MPP44 used as SD write protect */ + .gpio_card_detect = 47, /* MPP47 used as SD card detect */ +}; + static struct gpio_led sheevaplug_led_pins[] = { { .name = "plug:green:health", @@ -74,13 +84,26 @@ static unsigned int sheevaplug_mpp_config[] __initdata = { 0 }; +static unsigned int sheeva_esata_mpp_config[] __initdata = { + MPP29_GPIO, /* USB Power Enable */ + MPP44_GPIO, /* SD Write Protect */ + MPP47_GPIO, /* SD Card Detect */ + MPP49_GPIO, /* LED Green */ + 0 +}; + static void __init sheevaplug_init(void) { /* * Basic setup. Needs to be called early. */ kirkwood_init(); - kirkwood_mpp_conf(sheevaplug_mpp_config); + + /* setup gpio pin select */ + if (machine_is_sheeva_esata()) + kirkwood_mpp_conf(sheeva_esata_mpp_config); + else + kirkwood_mpp_conf(sheevaplug_mpp_config); kirkwood_uart0_init(); kirkwood_nand_init(ARRAY_AND_SIZE(sheevaplug_nand_parts), 25); @@ -91,11 +114,21 @@ static void __init sheevaplug_init(void) kirkwood_ehci_init(); kirkwood_ge00_init(&sheevaplug_ge00_data); - kirkwood_sdio_init(&sheevaplug_mvsdio_data); + + /* honor lower power consumption for plugs with out eSATA */ + if (machine_is_sheeva_esata()) + kirkwood_sata_init(&sheeva_esata_sata_data); + + /* enable sd wp and sd cd on plugs with esata */ + if (machine_is_sheeva_esata()) + kirkwood_sdio_init(&sheeva_esata_mvsdio_data); + else + kirkwood_sdio_init(&sheevaplug_mvsdio_data); platform_device_register(&sheevaplug_leds); } +#ifdef CONFIG_MACH_SHEEVAPLUG MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board") /* Maintainer: shadi Ammouri <shadi@marvell.com> */ .phys_io = KIRKWOOD_REGS_PHYS_BASE, @@ -106,3 +139,16 @@ MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board") .init_irq = kirkwood_init_irq, .timer = &kirkwood_timer, MACHINE_END +#endif + +#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG +MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board") + .phys_io = KIRKWOOD_REGS_PHYS_BASE, + .io_pg_offst = ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc, + .boot_params = 0x00000100, + .init_machine = sheevaplug_init, + .map_io = kirkwood_map_io, + .init_irq = kirkwood_init_irq, + .timer = &kirkwood_timer, +MACHINE_END +#endif |