summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-lpc32xx/phy3250.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/mach-lpc32xx/phy3250.c')
-rw-r--r--arch/arm/mach-lpc32xx/phy3250.c163
1 files changed, 57 insertions, 106 deletions
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 540106cdb9e..b07dcc90829 100644
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -30,12 +30,13 @@
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl022.h>
+#include <linux/amba/pl08x.h>
+#include <linux/amba/mmci.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/clk.h>
-#include <linux/amba/pl08x.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -50,9 +51,9 @@
/*
* Mapped GPIOLIB GPIOs
*/
-#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5)
-#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
-#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0)
+#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4)
+#define MMC_PWR_ENABLE_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5)
/*
* AMBA LCD controller
@@ -158,24 +159,6 @@ static struct clcd_board lpc32xx_clcd_data = {
/*
* AMBA SSP (SPI)
*/
-static void phy3250_spi_cs_set(u32 control)
-{
- gpio_set_value(SPI0_CS_GPIO, (int) control);
-}
-
-static struct pl022_config_chip spi0_chip_info = {
- .com_mode = INTERRUPT_TRANSFER,
- .iface = SSP_INTERFACE_MOTOROLA_SPI,
- .hierarchy = SSP_MASTER,
- .slave_tx_disable = 0,
- .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM,
- .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC,
- .ctrl_len = SSP_BITS_8,
- .wait_state = SSP_MWIRE_WAIT_ZERO,
- .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
- .cs_control = phy3250_spi_cs_set,
-};
-
static struct pl022_ssp_controller lpc32xx_ssp0_data = {
.bus_id = 0,
.num_chipselect = 1,
@@ -188,45 +171,56 @@ static struct pl022_ssp_controller lpc32xx_ssp1_data = {
.enable_dma = 0,
};
-/* AT25 driver registration */
-static int __init phy3250_spi_board_register(void)
+static struct pl08x_channel_data pl08x_slave_channels[] = {
+ {
+ .bus_id = "nand-slc",
+ .min_signal = 1, /* SLC NAND Flash */
+ .max_signal = 1,
+ .periph_buses = PL08X_AHB1,
+ },
+ {
+ .bus_id = "nand-mlc",
+ .min_signal = 12, /* MLC NAND Flash */
+ .max_signal = 12,
+ .periph_buses = PL08X_AHB1,
+ },
+};
+
+static int pl08x_get_signal(const struct pl08x_channel_data *cd)
+{
+ return cd->min_signal;
+}
+
+static void pl08x_put_signal(const struct pl08x_channel_data *cd, int ch)
{
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
- static struct spi_board_info info[] = {
- {
- .modalias = "spidev",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 0,
- .controller_data = &spi0_chip_info,
- },
- };
-
-#else
- static struct spi_eeprom eeprom = {
- .name = "at25256a",
- .byte_len = 0x8000,
- .page_size = 64,
- .flags = EE_ADDR2,
- };
-
- static struct spi_board_info info[] = {
- {
- .modalias = "at25",
- .max_speed_hz = 5000000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = SPI_MODE_0,
- .platform_data = &eeprom,
- .controller_data = &spi0_chip_info,
- },
- };
-#endif
- return spi_register_board_info(info, ARRAY_SIZE(info));
}
-arch_initcall(phy3250_spi_board_register);
static struct pl08x_platform_data pl08x_pd = {
+ .slave_channels = &pl08x_slave_channels[0],
+ .num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
+ .get_signal = pl08x_get_signal,
+ .put_signal = pl08x_put_signal,
+ .lli_buses = PL08X_AHB1,
+ .mem_buses = PL08X_AHB1,
+};
+
+static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios)
+{
+ /* Only on and off are supported */
+ if (ios->power_mode == MMC_POWER_OFF)
+ gpio_set_value(MMC_PWR_ENABLE_GPIO, 0);
+ else
+ gpio_set_value(MMC_PWR_ENABLE_GPIO, 1);
+ return 0;
+}
+
+static struct mmci_platform_data lpc32xx_mmci_data = {
+ .ocr_mask = MMC_VDD_30_31 | MMC_VDD_31_32 |
+ MMC_VDD_32_33 | MMC_VDD_33_34,
+ .ios_handler = mmc_handle_ios,
+ .dma_filter = NULL,
+ /* No DMA for now since AMBA PL080 dmaengine driver only does scatter
+ * gather, and the MMCI driver doesn't do it this way */
};
static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
@@ -234,6 +228,8 @@ static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
+ OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd",
+ &lpc32xx_mmci_data),
{ }
};
@@ -241,10 +237,6 @@ static void __init lpc3250_machine_init(void)
{
u32 tmp;
- /* Setup SLC NAND controller muxing */
- __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC,
- LPC32XX_CLKPWR_NAND_CLK_CTRL);
-
/* Setup LCD muxing to RGB565 */
tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) &
~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK |
@@ -252,47 +244,8 @@ static void __init lpc3250_machine_init(void)
tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16;
__raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL);
- /* Set up USB power */
- tmp = __raw_readl(LPC32XX_CLKPWR_USB_CTRL);
- tmp |= LPC32XX_CLKPWR_USBCTRL_HCLK_EN |
- LPC32XX_CLKPWR_USBCTRL_USBI2C_EN;
- __raw_writel(tmp, LPC32XX_CLKPWR_USB_CTRL);
-
- /* Set up I2C pull levels */
- tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL);
- tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE |
- LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE;
- __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL);
-
- /* Disable IrDA pulsing support on UART6 */
- tmp = __raw_readl(LPC32XX_UARTCTL_CTRL);
- tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS;
- __raw_writel(tmp, LPC32XX_UARTCTL_CTRL);
-
- /* Enable DMA for I2S1 channel */
- tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL);
- tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA;
- __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL);
-
lpc32xx_serial_init();
- /*
- * AMBA peripheral clocks need to be enabled prior to AMBA device
- * detection or a data fault will occur, so enable the clocks
- * here.
- */
- tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN),
- LPC32XX_CLKPWR_LCDCLK_CTRL);
-
- tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN),
- LPC32XX_CLKPWR_SSP_CLK_CTRL);
-
- tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL);
- __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN),
- LPC32XX_CLKPWR_DMA_CLK_CTRL);
-
/* Test clock needed for UDA1380 initial init */
__raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC |
LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN,
@@ -302,12 +255,10 @@ static void __init lpc3250_machine_init(void)
lpc32xx_auxdata_lookup, NULL);
/* Register GPIOs used on this board */
- if (gpio_request(SPI0_CS_GPIO, "spi0 cs"))
- printk(KERN_ERR "Error requesting gpio %u",
- SPI0_CS_GPIO);
- else if (gpio_direction_output(SPI0_CS_GPIO, 1))
- printk(KERN_ERR "Error setting gpio %u to output",
- SPI0_CS_GPIO);
+ if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en"))
+ pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO);
+ else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1))
+ pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO);
}
static char const *lpc32xx_dt_compat[] __initdata = {