diff options
Diffstat (limited to 'arch/arm/mach-lpc32xx/phy3250.c')
| -rw-r--r-- | arch/arm/mach-lpc32xx/phy3250.c | 163 |
1 files changed, 57 insertions, 106 deletions
diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c index 540106cdb9e..b07dcc90829 100644 --- a/arch/arm/mach-lpc32xx/phy3250.c +++ b/arch/arm/mach-lpc32xx/phy3250.c @@ -30,12 +30,13 @@ #include <linux/amba/bus.h> #include <linux/amba/clcd.h> #include <linux/amba/pl022.h> +#include <linux/amba/pl08x.h> +#include <linux/amba/mmci.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/clk.h> -#include <linux/amba/pl08x.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -50,9 +51,9 @@ /* * Mapped GPIOLIB GPIOs */ -#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) -#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0) -#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4) +#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0) +#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4) +#define MMC_PWR_ENABLE_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5) /* * AMBA LCD controller @@ -158,24 +159,6 @@ static struct clcd_board lpc32xx_clcd_data = { /* * AMBA SSP (SPI) */ -static void phy3250_spi_cs_set(u32 control) -{ - gpio_set_value(SPI0_CS_GPIO, (int) control); -} - -static struct pl022_config_chip spi0_chip_info = { - .com_mode = INTERRUPT_TRANSFER, - .iface = SSP_INTERFACE_MOTOROLA_SPI, - .hierarchy = SSP_MASTER, - .slave_tx_disable = 0, - .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM, - .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC, - .ctrl_len = SSP_BITS_8, - .wait_state = SSP_MWIRE_WAIT_ZERO, - .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, - .cs_control = phy3250_spi_cs_set, -}; - static struct pl022_ssp_controller lpc32xx_ssp0_data = { .bus_id = 0, .num_chipselect = 1, @@ -188,45 +171,56 @@ static struct pl022_ssp_controller lpc32xx_ssp1_data = { .enable_dma = 0, }; -/* AT25 driver registration */ -static int __init phy3250_spi_board_register(void) +static struct pl08x_channel_data pl08x_slave_channels[] = { + { + .bus_id = "nand-slc", + .min_signal = 1, /* SLC NAND Flash */ + .max_signal = 1, + .periph_buses = PL08X_AHB1, + }, + { + .bus_id = "nand-mlc", + .min_signal = 12, /* MLC NAND Flash */ + .max_signal = 12, + .periph_buses = PL08X_AHB1, + }, +}; + +static int pl08x_get_signal(const struct pl08x_channel_data *cd) +{ + return cd->min_signal; +} + +static void pl08x_put_signal(const struct pl08x_channel_data *cd, int ch) { -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) - static struct spi_board_info info[] = { - { - .modalias = "spidev", - .max_speed_hz = 5000000, - .bus_num = 0, - .chip_select = 0, - .controller_data = &spi0_chip_info, - }, - }; - -#else - static struct spi_eeprom eeprom = { - .name = "at25256a", - .byte_len = 0x8000, - .page_size = 64, - .flags = EE_ADDR2, - }; - - static struct spi_board_info info[] = { - { - .modalias = "at25", - .max_speed_hz = 5000000, - .bus_num = 0, - .chip_select = 0, - .mode = SPI_MODE_0, - .platform_data = &eeprom, - .controller_data = &spi0_chip_info, - }, - }; -#endif - return spi_register_board_info(info, ARRAY_SIZE(info)); } -arch_initcall(phy3250_spi_board_register); static struct pl08x_platform_data pl08x_pd = { + .slave_channels = &pl08x_slave_channels[0], + .num_slave_channels = ARRAY_SIZE(pl08x_slave_channels), + .get_signal = pl08x_get_signal, + .put_signal = pl08x_put_signal, + .lli_buses = PL08X_AHB1, + .mem_buses = PL08X_AHB1, +}; + +static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios) +{ + /* Only on and off are supported */ + if (ios->power_mode == MMC_POWER_OFF) + gpio_set_value(MMC_PWR_ENABLE_GPIO, 0); + else + gpio_set_value(MMC_PWR_ENABLE_GPIO, 1); + return 0; +} + +static struct mmci_platform_data lpc32xx_mmci_data = { + .ocr_mask = MMC_VDD_30_31 | MMC_VDD_31_32 | + MMC_VDD_32_33 | MMC_VDD_33_34, + .ios_handler = mmc_handle_ios, + .dma_filter = NULL, + /* No DMA for now since AMBA PL080 dmaengine driver only does scatter + * gather, and the MMCI driver doesn't do it this way */ }; static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = { @@ -234,6 +228,8 @@ static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = { OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data), OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data), OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd), + OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd", + &lpc32xx_mmci_data), { } }; @@ -241,10 +237,6 @@ static void __init lpc3250_machine_init(void) { u32 tmp; - /* Setup SLC NAND controller muxing */ - __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC, - LPC32XX_CLKPWR_NAND_CLK_CTRL); - /* Setup LCD muxing to RGB565 */ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) & ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK | @@ -252,47 +244,8 @@ static void __init lpc3250_machine_init(void) tmp |= LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_TFT16; __raw_writel(tmp, LPC32XX_CLKPWR_LCDCLK_CTRL); - /* Set up USB power */ - tmp = __raw_readl(LPC32XX_CLKPWR_USB_CTRL); - tmp |= LPC32XX_CLKPWR_USBCTRL_HCLK_EN | - LPC32XX_CLKPWR_USBCTRL_USBI2C_EN; - __raw_writel(tmp, LPC32XX_CLKPWR_USB_CTRL); - - /* Set up I2C pull levels */ - tmp = __raw_readl(LPC32XX_CLKPWR_I2C_CLK_CTRL); - tmp |= LPC32XX_CLKPWR_I2CCLK_USBI2CHI_DRIVE | - LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE; - __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL); - - /* Disable IrDA pulsing support on UART6 */ - tmp = __raw_readl(LPC32XX_UARTCTL_CTRL); - tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS; - __raw_writel(tmp, LPC32XX_UARTCTL_CTRL); - - /* Enable DMA for I2S1 channel */ - tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL); - tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA; - __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL); - lpc32xx_serial_init(); - /* - * AMBA peripheral clocks need to be enabled prior to AMBA device - * detection or a data fault will occur, so enable the clocks - * here. - */ - tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN), - LPC32XX_CLKPWR_LCDCLK_CTRL); - - tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN), - LPC32XX_CLKPWR_SSP_CLK_CTRL); - - tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN), - LPC32XX_CLKPWR_DMA_CLK_CTRL); - /* Test clock needed for UDA1380 initial init */ __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC | LPC32XX_CLKPWR_TESTCLK_TESTCLK2_EN, @@ -302,12 +255,10 @@ static void __init lpc3250_machine_init(void) lpc32xx_auxdata_lookup, NULL); /* Register GPIOs used on this board */ - if (gpio_request(SPI0_CS_GPIO, "spi0 cs")) - printk(KERN_ERR "Error requesting gpio %u", - SPI0_CS_GPIO); - else if (gpio_direction_output(SPI0_CS_GPIO, 1)) - printk(KERN_ERR "Error setting gpio %u to output", - SPI0_CS_GPIO); + if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en")) + pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO); + else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1)) + pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO); } static char const *lpc32xx_dt_compat[] __initdata = { |