diff options
Diffstat (limited to 'arch/arm/mach-omap1')
| -rw-r--r-- | arch/arm/mach-omap1/Kconfig | 32 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/Makefile | 5 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-generic.c | 33 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-h2.c | 15 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-h3.c | 19 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-innovator.c | 42 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-netstar.c | 15 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-osk.c | 17 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-palmte.c | 87 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-perseus2.c | 23 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/board-voiceblue.c | 9 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/clock.c | 792 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/clock.h | 768 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/devices.c | 221 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/id.c | 9 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/io.c | 13 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/irq.c | 23 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/leds-h2p2-debug.c | 43 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/leds.c | 1 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/mux.c | 289 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/serial.c | 9 | ||||
| -rw-r--r-- | arch/arm/mach-omap1/time.c | 4 |
22 files changed, 2155 insertions, 314 deletions
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig index 27fc2e8e5fc..86a0f0d1434 100644 --- a/arch/arm/mach-omap1/Kconfig +++ b/arch/arm/mach-omap1/Kconfig @@ -6,10 +6,10 @@ config ARCH_OMAP730 bool "OMAP730 Based System" select ARCH_OMAP_OTG -config ARCH_OMAP1510 +config ARCH_OMAP15XX depends on ARCH_OMAP1 default y - bool "OMAP1510 Based System" + bool "OMAP15xx Based System" config ARCH_OMAP16XX depends on ARCH_OMAP1 @@ -21,7 +21,7 @@ comment "OMAP Board Type" config MACH_OMAP_INNOVATOR bool "TI Innovator" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX) help TI OMAP 1510 or 1610 Innovator board support. Say Y here if you have such a board. @@ -64,20 +64,30 @@ config MACH_OMAP_PERSEUS2 config MACH_VOICEBLUE bool "Voiceblue" - depends on ARCH_OMAP1 && ARCH_OMAP1510 + depends on ARCH_OMAP1 && ARCH_OMAP15XX help Support for Voiceblue GSM/VoIP gateway. Say Y here if you have such a board. config MACH_NETSTAR bool "NetStar" - depends on ARCH_OMAP1 && ARCH_OMAP1510 + depends on ARCH_OMAP1 && ARCH_OMAP15XX help Support for NetStar PBX. Say Y here if you have such a board. +config MACH_OMAP_PALMTE + bool "Palm Tungsten E" + depends on ARCH_OMAP1 && ARCH_OMAP15XX + help + Support for the Palm Tungsten E PDA. Currently only the LCD panel + is supported. To boot the kernel, you'll need a PalmOS compatible + bootloader; check out http://palmtelinux.sourceforge.net for more + informations. + Say Y here if you have such a PDA, say NO otherwise. + config MACH_OMAP_GENERIC bool "Generic OMAP board" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX) help Support for generic OMAP-1510, 1610 or 1710 board with no FPGA. Can be used as template for porting Linux to @@ -121,32 +131,32 @@ config OMAP_ARM_182MHZ config OMAP_ARM_168MHZ bool "OMAP ARM 168 MHz CPU" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730) help Enable 168MHz clock for OMAP CPU. If unsure, say N. config OMAP_ARM_150MHZ bool "OMAP ARM 150 MHz CPU" - depends on ARCH_OMAP1 && ARCH_OMAP1510 + depends on ARCH_OMAP1 && ARCH_OMAP15XX help Enable 150MHz clock for OMAP CPU. If unsure, say N. config OMAP_ARM_120MHZ bool "OMAP ARM 120 MHz CPU" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730) help Enable 120MHz clock for OMAP CPU. If unsure, say N. config OMAP_ARM_60MHZ bool "OMAP ARM 60 MHz CPU" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730) default y help Enable 60MHz clock for OMAP CPU. If unsure, say Y. config OMAP_ARM_30MHZ bool "OMAP ARM 30 MHz CPU" - depends on ARCH_OMAP1 && (ARCH_OMAP1510 || ARCH_OMAP16XX || ARCH_OMAP730) + depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730) help Enable 30MHz clock for OMAP CPU. If unsure, say N. diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile index 181a93deaae..b0b00156faa 100644 --- a/arch/arm/mach-omap1/Makefile +++ b/arch/arm/mach-omap1/Makefile @@ -3,7 +3,7 @@ # # Common support -obj-y := io.o id.o irq.o time.o serial.o devices.o +obj-y := io.o id.o clock.o irq.o time.o mux.o serial.o devices.o led-y := leds.o # Specific board support @@ -15,8 +15,9 @@ obj-$(CONFIG_MACH_OMAP_OSK) += board-osk.o obj-$(CONFIG_MACH_OMAP_H3) += board-h3.o obj-$(CONFIG_MACH_VOICEBLUE) += board-voiceblue.o obj-$(CONFIG_MACH_NETSTAR) += board-netstar.o +obj-$(CONFIG_MACH_OMAP_PALMTE) += board-palmte.o -ifeq ($(CONFIG_ARCH_OMAP1510),y) +ifeq ($(CONFIG_ARCH_OMAP15XX),y) # Innovator-1510 FPGA obj-$(CONFIG_MACH_OMAP_INNOVATOR) += fpga.o endif diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c index c209c7172a9..4b292e93fbe 100644 --- a/arch/arm/mach-omap1/board-generic.c +++ b/arch/arm/mach-omap1/board-generic.c @@ -15,7 +15,7 @@ #include <linux/kernel.h> #include <linux/init.h> -#include <linux/device.h> +#include <linux/platform_device.h> #include <asm/hardware.h> #include <asm/mach-types.h> @@ -28,8 +28,6 @@ #include <asm/arch/board.h> #include <asm/arch/common.h> -static int __initdata generic_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; - static void __init omap_generic_init_irq(void) { omap_init_irq(); @@ -37,7 +35,7 @@ static void __init omap_generic_init_irq(void) /* assume no Mini-AB port */ -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX static struct omap_usb_config generic1510_usb_config __initdata = { .register_host = 1, .register_dev = 1, @@ -76,21 +74,19 @@ static struct omap_mmc_config generic_mmc_config __initdata = { #endif +static struct omap_uart_config generic_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + static struct omap_board_config_kernel generic_config[] = { { OMAP_TAG_USB, NULL }, { OMAP_TAG_MMC, &generic_mmc_config }, + { OMAP_TAG_UART, &generic_uart_config }, }; static void __init omap_generic_init(void) { - const struct omap_uart_config *uart_conf; - - /* - * Make sure the serial ports are muxed on at this point. - * You have to mux them off in device drivers later on - * if not needed. - */ -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { generic_config[0].data = &generic1510_usb_config; } @@ -101,20 +97,9 @@ static void __init omap_generic_init(void) } #endif - uart_conf = omap_get_config(OMAP_TAG_UART, struct omap_uart_config); - if (uart_conf != NULL) { - unsigned int enabled_ports, i; - - enabled_ports = uart_conf->enabled_uarts; - for (i = 0; i < 3; i++) { - if (!(enabled_ports & (1 << i))) - generic_serial_ports[i] = 0; - } - } - omap_board_config = generic_config; omap_board_config_size = ARRAY_SIZE(generic_config); - omap_serial_init(generic_serial_ports); + omap_serial_init(); } static void __init omap_generic_map_io(void) diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c index 4ee6bd8a50b..a07e2c9307f 100644 --- a/arch/arm/mach-omap1/board-h2.c +++ b/arch/arm/mach-omap1/board-h2.c @@ -40,8 +40,6 @@ extern int omap_gpio_init(void); -static int __initdata h2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; - static struct mtd_partition h2_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -160,9 +158,20 @@ static struct omap_mmc_config h2_mmc_config __initdata = { }, }; +static struct omap_uart_config h2_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + +static struct omap_lcd_config h2_lcd_config __initdata = { + .panel_name = "h2", + .ctrl_name = "internal", +}; + static struct omap_board_config_kernel h2_config[] = { { OMAP_TAG_USB, &h2_usb_config }, { OMAP_TAG_MMC, &h2_mmc_config }, + { OMAP_TAG_UART, &h2_uart_config }, + { OMAP_TAG_LCD, &h2_lcd_config }, }; static void __init h2_init(void) @@ -180,12 +189,12 @@ static void __init h2_init(void) platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices)); omap_board_config = h2_config; omap_board_config_size = ARRAY_SIZE(h2_config); + omap_serial_init(); } static void __init h2_map_io(void) { omap_map_common_io(); - omap_serial_init(h2_serial_ports); } MACHINE_START(OMAP_H2, "TI-H2") diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c index fc824361430..668e278433c 100644 --- a/arch/arm/mach-omap1/board-h3.c +++ b/arch/arm/mach-omap1/board-h3.c @@ -41,8 +41,6 @@ extern int omap_gpio_init(void); -static int __initdata h3_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; - static struct mtd_partition h3_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -168,9 +166,20 @@ static struct omap_mmc_config h3_mmc_config __initdata = { }, }; +static struct omap_uart_config h3_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + +static struct omap_lcd_config h3_lcd_config __initdata = { + .panel_name = "h3", + .ctrl_name = "internal", +}; + static struct omap_board_config_kernel h3_config[] = { - { OMAP_TAG_USB, &h3_usb_config }, - { OMAP_TAG_MMC, &h3_mmc_config }, + { OMAP_TAG_USB, &h3_usb_config }, + { OMAP_TAG_MMC, &h3_mmc_config }, + { OMAP_TAG_UART, &h3_uart_config }, + { OMAP_TAG_LCD, &h3_lcd_config }, }; static void __init h3_init(void) @@ -180,6 +189,7 @@ static void __init h3_init(void) (void) platform_add_devices(devices, ARRAY_SIZE(devices)); omap_board_config = h3_config; omap_board_config_size = ARRAY_SIZE(h3_config); + omap_serial_init(); } static void __init h3_init_smc91x(void) @@ -201,7 +211,6 @@ void h3_init_irq(void) static void __init h3_map_io(void) { omap_map_common_io(); - omap_serial_init(h3_serial_ports); } MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board") diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c index a2eac853b2d..95f1ff36cdc 100644 --- a/arch/arm/mach-omap1/board-innovator.c +++ b/arch/arm/mach-omap1/board-innovator.c @@ -36,8 +36,6 @@ #include <asm/arch/usb.h> #include <asm/arch/common.h> -static int __initdata innovator_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; - static struct mtd_partition innovator_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -99,7 +97,7 @@ static struct platform_device innovator_flash_device = { .resource = &innovator_flash_resource, }; -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX /* Only FPGA needs to be mapped here. All others are done with ioremap */ static struct map_desc innovator1510_io_desc[] __initdata = { @@ -136,7 +134,7 @@ static struct platform_device *innovator1510_devices[] __initdata = { &innovator1510_smc91x_device, }; -#endif /* CONFIG_ARCH_OMAP1510 */ +#endif /* CONFIG_ARCH_OMAP15XX */ #ifdef CONFIG_ARCH_OMAP16XX @@ -185,7 +183,7 @@ void innovator_init_irq(void) { omap_init_irq(); omap_gpio_init(); -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { omap1510_fpga_init_irq(); } @@ -193,7 +191,7 @@ void innovator_init_irq(void) innovator_init_smc91x(); } -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX static struct omap_usb_config innovator1510_usb_config __initdata = { /* for bundled non-standard host and peripheral cables */ .hmc_mode = 4, @@ -205,6 +203,11 @@ static struct omap_usb_config innovator1510_usb_config __initdata = { .register_dev = 1, .pins[0] = 2, }; + +static struct omap_lcd_config innovator1510_lcd_config __initdata = { + .panel_name = "inn1510", + .ctrl_name = "internal", +}; #endif #ifdef CONFIG_ARCH_OMAP16XX @@ -222,6 +225,11 @@ static struct omap_usb_config h2_usb_config __initdata = { .pins[1] = 3, }; + +static struct omap_lcd_config innovator1610_lcd_config __initdata = { + .panel_name = "inn1610", + .ctrl_name = "internal", +}; #endif static struct omap_mmc_config innovator_mmc_config __initdata = { @@ -234,14 +242,20 @@ static struct omap_mmc_config innovator_mmc_config __initdata = { }, }; +static struct omap_uart_config innovator_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + static struct omap_board_config_kernel innovator_config[] = { { OMAP_TAG_USB, NULL }, + { OMAP_TAG_LCD, NULL }, { OMAP_TAG_MMC, &innovator_mmc_config }, + { OMAP_TAG_UART, &innovator_uart_config }, }; static void __init innovator_init(void) { -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { platform_add_devices(innovator1510_devices, ARRAY_SIZE(innovator1510_devices)); } @@ -252,23 +266,28 @@ static void __init innovator_init(void) } #endif -#ifdef CONFIG_ARCH_OMAP1510 - if (cpu_is_omap1510()) +#ifdef CONFIG_ARCH_OMAP15XX + if (cpu_is_omap1510()) { innovator_config[0].data = &innovator1510_usb_config; + innovator_config[1].data = &innovator1510_lcd_config; + } #endif #ifdef CONFIG_ARCH_OMAP16XX - if (cpu_is_omap1610()) + if (cpu_is_omap1610()) { innovator_config[0].data = &h2_usb_config; + innovator_config[1].data = &innovator1610_lcd_config; + } #endif omap_board_config = innovator_config; omap_board_config_size = ARRAY_SIZE(innovator_config); + omap_serial_init(); } static void __init innovator_map_io(void) { omap_map_common_io(); -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { iotable_init(innovator1510_io_desc, ARRAY_SIZE(innovator1510_io_desc)); udelay(10); /* Delay needed for FPGA */ @@ -280,7 +299,6 @@ static void __init innovator_map_io(void) fpga_read(OMAP1510_FPGA_BOARD_REV)); } #endif - omap_serial_init(innovator_serial_ports); } MACHINE_START(OMAP_INNOVATOR, "TI-Innovator") diff --git a/arch/arm/mach-omap1/board-netstar.c b/arch/arm/mach-omap1/board-netstar.c index c851c2e4dfc..0448fa7de8a 100644 --- a/arch/arm/mach-omap1/board-netstar.c +++ b/arch/arm/mach-omap1/board-netstar.c @@ -55,6 +55,14 @@ static struct platform_device *netstar_devices[] __initdata = { &netstar_smc91x_device, }; +static struct omap_uart_config netstar_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + +static struct omap_board_config_kernel netstar_config[] = { + { OMAP_TAG_UART, &netstar_uart_config }, +}; + static void __init netstar_init_irq(void) { omap_init_irq(); @@ -92,14 +100,15 @@ static void __init netstar_init(void) /* Switch off red LED */ omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */ omap_writeb(0x80, OMAP_LPG1_LCR); -} -static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; + omap_board_config = netstar_config; + omap_board_config_size = ARRAY_SIZE(netstar_config); + omap_serial_init(); +} static void __init netstar_map_io(void) { omap_map_common_io(); - omap_serial_init(omap_serial_ports); } #define MACHINE_PANICED 1 diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c index a88524e7c31..e990e1bc166 100644 --- a/arch/arm/mach-omap1/board-osk.c +++ b/arch/arm/mach-omap1/board-osk.c @@ -46,8 +46,6 @@ #include <asm/arch/tc.h> #include <asm/arch/common.h> -static int __initdata osk_serial_ports[OMAP_MAX_NR_PORTS] = {1, 0, 0}; - static struct mtd_partition osk_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -155,7 +153,7 @@ static void __init osk_init_smc91x(void) } /* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */ - EMIFS_CCS(1) |= 0x2; + EMIFS_CCS(1) |= 0x3; } static void __init osk_init_cf(void) @@ -193,8 +191,19 @@ static struct omap_usb_config osk_usb_config __initdata = { .pins[0] = 2, }; +static struct omap_uart_config osk_uart_config __initdata = { + .enabled_uarts = (1 << 0), +}; + +static struct omap_lcd_config osk_lcd_config __initdata = { + .panel_name = "osk", + .ctrl_name = "internal", +}; + static struct omap_board_config_kernel osk_config[] = { { OMAP_TAG_USB, &osk_usb_config }, + { OMAP_TAG_UART, &osk_uart_config }, + { OMAP_TAG_LCD, &osk_lcd_config }, }; #ifdef CONFIG_OMAP_OSK_MISTRAL @@ -254,13 +263,13 @@ static void __init osk_init(void) omap_board_config_size = ARRAY_SIZE(osk_config); USB_TRANSCEIVER_CTRL_REG |= (3 << 1); + omap_serial_init(); osk_mistral_init(); } static void __init osk_map_io(void) { omap_map_common_io(); - omap_serial_init(osk_serial_ports); } MACHINE_START(OMAP_OSK, "TI-OSK") diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c new file mode 100644 index 00000000000..540b20d78cc --- /dev/null +++ b/arch/arm/mach-omap1/board-palmte.c @@ -0,0 +1,87 @@ +/* + * linux/arch/arm/mach-omap1/board-palmte.c + * + * Modified from board-generic.c + * + * Support for the Palm Tungsten E PDA. + * + * Original version : Laurent Gonzalez + * + * Maintainters : http://palmtelinux.sf.net + * palmtelinux-developpers@lists.sf.net + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/notifier.h> + +#include <asm/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <asm/arch/gpio.h> +#include <asm/arch/mux.h> +#include <asm/arch/usb.h> +#include <asm/arch/board.h> +#include <asm/arch/common.h> +#include <asm/hardware/clock.h> + +static void __init omap_generic_init_irq(void) +{ + omap_init_irq(); +} + +static struct omap_usb_config palmte_usb_config __initdata = { + .register_dev = 1, + .hmc_mode = 0, + .pins[0] = 3, +}; + +static struct omap_mmc_config palmte_mmc_config __initdata = { + .mmc [0] = { + .enabled = 1, + .wire4 = 1, + .wp_pin = OMAP_MPUIO(3), + .power_pin = -1, + .switch_pin = -1, + }, +}; + +static struct omap_lcd_config palmte_lcd_config __initdata = { + .panel_name = "palmte", + .ctrl_name = "internal", +}; + +static struct omap_board_config_kernel palmte_config[] = { + { OMAP_TAG_USB, &palmte_usb_config }, + { OMAP_TAG_MMC, &palmte_mmc_config }, + { OMAP_TAG_LCD, &palmte_lcd_config }, +}; + +static void __init omap_generic_init(void) +{ + omap_board_config = palmte_config; + omap_board_config_size = ARRAY_SIZE(palmte_config); +} + +static void __init omap_generic_map_io(void) +{ + omap_map_common_io(); +} + +MACHINE_START(OMAP_PALMTE, "OMAP310 based Palm Tungsten E") + .phys_ram = 0x10000000, + .phys_io = 0xfff00000, + .io_pg_offst = ((0xfef00000) >> 18) & 0xfffc, + .boot_params = 0x10000100, + .map_io = omap_generic_map_io, + .init_irq = omap_generic_init_irq, + .init_machine = omap_generic_init, + .timer = &omap_timer, +MACHINE_END diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c index 354b157acb3..bd900b7ab33 100644 --- a/arch/arm/mach-omap1/board-perseus2.c +++ b/arch/arm/mach-omap1/board-perseus2.c @@ -29,6 +29,7 @@ #include <asm/arch/mux.h> #include <asm/arch/fpga.h> #include <asm/arch/common.h> +#include <asm/arch/board.h> static struct resource smc91x_resources[] = { [0] = { @@ -43,8 +44,6 @@ static struct resource smc91x_resources[] = { }, }; -static int __initdata p2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 0}; - static struct mtd_partition p2_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -111,9 +110,27 @@ static struct platform_device *devices[] __initdata = { &smc91x_device, }; +static struct omap_uart_config perseus2_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1)), +}; + +static struct omap_lcd_config perseus2_lcd_config __initdata = { + .panel_name = "p2", + .ctrl_name = "internal", +}; + +static struct omap_board_config_kernel perseus2_config[] = { + { OMAP_TAG_UART, &perseus2_uart_config }, + { OMAP_TAG_LCD, &perseus2_lcd_config }, +}; + static void __init omap_perseus2_init(void) { (void) platform_add_devices(devices, ARRAY_SIZE(devices)); + + omap_board_config = perseus2_config; + omap_board_config_size = ARRAY_SIZE(perseus2_config); + omap_serial_init(); } static void __init perseus2_init_smc91x(void) @@ -131,7 +148,6 @@ void omap_perseus2_init_irq(void) omap_gpio_init(); perseus2_init_smc91x(); } - /* Only FPGA needs to be mapped here. All others are done with ioremap */ static struct map_desc omap_perseus2_io_desc[] __initdata = { { @@ -179,7 +195,6 @@ static void __init omap_perseus2_map_io(void) * It is used as the Ethernet controller interrupt */ omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9); - omap_serial_init(p2_serial_ports); } MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2") diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c index 3f018b29686..6f9a6220e78 100644 --- a/arch/arm/mach-omap1/board-voiceblue.c +++ b/arch/arm/mach-omap1/board-voiceblue.c @@ -150,9 +150,14 @@ static struct omap_mmc_config voiceblue_mmc_config __initdata = { }, }; +static struct omap_uart_config voiceblue_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + static struct omap_board_config_kernel voiceblue_config[] = { { OMAP_TAG_USB, &voiceblue_usb_config }, { OMAP_TAG_MMC, &voiceblue_mmc_config }, + { OMAP_TAG_UART, &voiceblue_uart_config }, }; static void __init voiceblue_init_irq(void) @@ -191,6 +196,7 @@ static void __init voiceblue_init(void) platform_add_devices(voiceblue_devices, ARRAY_SIZE(voiceblue_devices)); omap_board_config = voiceblue_config; omap_board_config_size = ARRAY_SIZE(voiceblue_config); + omap_serial_init(); /* There is a good chance board is going up, so enable power LED * (it is connected through invertor) */ @@ -198,12 +204,9 @@ static void __init voiceblue_init(void) omap_writeb(0x00, OMAP_LPG1_PMR); /* Disable clock */ } -static int __initdata omap_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1}; - static void __init voiceblue_map_io(void) { omap_map_common_io(); - omap_serial_init(omap_serial_ports); } #define MACHINE_PANICED 1 diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c new file mode 100644 index 00000000000..4277eee44ed --- /dev/null +++ b/arch/arm/mach-omap1/clock.c @@ -0,0 +1,792 @@ +/* + * linux/arch/arm/mach-omap1/clock.c + * + * Copyright (C) 2004 - 2005 Nokia corporation + * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com> + * + * Modified to use omap shared clock framework by + * Tony Lindgren <tony@atomide.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/errno.h> +#include <linux/err.h> + +#include <asm/io.h> +#include <asm/hardware/clock.h> + +#include <asm/arch/usb.h> +#include <asm/arch/clock.h> +#include <asm/arch/sram.h> + +#include "clock.h" + +__u32 arm_idlect1_mask; + +/*------------------------------------------------------------------------- + * Omap1 specific clock functions + *-------------------------------------------------------------------------*/ + +static void omap1_watchdog_recalc(struct clk * clk) +{ + clk->rate = clk->parent->rate / 14; +} + +static void omap1_uart_recalc(struct clk * clk) +{ + unsigned int val = omap_readl(clk->enable_reg); + if (val & clk->enable_bit) + clk->rate = 48000000; + else + clk->rate = 12000000; +} + +static int omap1_clk_enable_dsp_domain(struct clk *clk) +{ + int retval; + + retval = omap1_clk_use(&api_ck.clk); + if (!retval) { + retval = omap1_clk_enable(clk); + omap1_clk_unuse(&api_ck.clk); + } + + return retval; +} + +static void omap1_clk_disable_dsp_domain(struct clk *clk) +{ + if (omap1_clk_use(&api_ck.clk) == 0) { + omap1_clk_disable(clk); + omap1_clk_unuse(&api_ck.clk); + } +} + +static int omap1_clk_enable_uart_functional(struct clk *clk) +{ + int ret; + struct uart_clk *uclk; + + ret = omap1_clk_enable(clk); + if (ret == 0) { + /* Set smart idle acknowledgement mode */ + uclk = (struct uart_clk *)clk; + omap_writeb((omap_readb(uclk->sysc_addr) & ~0x10) | 8, + uclk->sysc_addr); + } + + return ret; +} + +static void omap1_clk_disable_uart_functional(struct clk *clk) +{ + struct uart_clk *uclk; + + /* Set force idle acknowledgement mode */ + uclk = (struct uart_clk *)clk; + omap_writeb((omap_readb(uclk->sysc_addr) & ~0x18), uclk->sysc_addr); + + omap1_clk_disable(clk); +} + +static void omap1_clk_allow_idle(struct clk *clk) +{ + struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk; + + if (!(clk->flags & CLOCK_IDLE_CONTROL)) + return; + + if (iclk->no_idle_count > 0 && !(--iclk->no_idle_count)) + arm_idlect1_mask |= 1 << iclk->idlect_shift; +} + +static void omap1_clk_deny_idle(struct clk *clk) +{ + struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk; + + if (!(clk->flags & CLOCK_IDLE_CONTROL)) + return; + + if (iclk->no_idle_count++ == 0) + arm_idlect1_mask &= ~(1 << iclk->idlect_shift); +} + +static __u16 verify_ckctl_value(__u16 newval) +{ + /* This function checks for following limitations set + * by the hardware (all conditions must be true): + * DSPMMU_CK == DSP_CK or DSPMMU_CK == DSP_CK/2 + * ARM_CK >= TC_CK + * DSP_CK >= TC_CK + * DSPMMU_CK >= TC_CK + * + * In addition following rules are enforced: + * LCD_CK <= TC_CK + * ARMPER_CK <= TC_CK + * + * However, maximum frequencies are not checked for! + */ + __u8 per_exp; + __u8 lcd_exp; + __u8 arm_exp; + __u8 dsp_exp; + __u8 tc_exp; + __u8 dspmmu_exp; + + per_exp = (newval >> CKCTL_PERDIV_OFFSET) & 3; + lcd_exp = (newval >> CKCTL_LCDDIV_OFFSET) & 3; + arm_exp = (newval >> CKCTL_ARMDIV_OFFSET) & 3; + dsp_exp = (newval >> CKCTL_DSPDIV_OFFSET) & 3; + tc_exp = (newval >> CKCTL_TCDIV_OFFSET) & 3; + dspmmu_exp = (newval >> CKCTL_DSPMMUDIV_OFFSET) & 3; + + if (dspmmu_exp < dsp_exp) + dspmmu_exp = dsp_exp; + if (dspmmu_exp > dsp_exp+1) + dspmmu_exp = dsp_exp+1; + if (tc_exp < arm_exp) + tc_exp = arm_exp; + if (tc_exp < dspmmu_exp) + tc_exp = dspmmu_exp; + if (tc_exp > lcd_exp) + lcd_exp = tc_exp; + if (tc_exp > per_exp) + per_exp = tc_exp; + + newval &= 0xf000; + newval |= per_exp << CKCTL_PERDIV_OFFSET; + newval |= lcd_exp << CKCTL_LCDDIV_OFFSET; + newval |= arm_exp << CKCTL_ARMDIV_OFFSET; + newval |= dsp_exp << CKCTL_DSPDIV_OFFSET; + newval |= tc_exp << CKCTL_TCDIV_OFFSET; + newval |= dspmmu_exp << CKCTL_DSPMMUDIV_OFFSET; + + return newval; +} + +static int calc_dsor_exp(struct clk *clk, unsigned long rate) +{ + /* Note: If target frequency is too low, this function will return 4, + * which is invalid value. Caller must check for this value and act + * accordingly. + * + * Note: This function does not check for following limitations set + * by the hardware (all conditions must be true): + * DSPMMU_CK == DSP_CK or DSPMMU_CK == DSP_CK/2 + * ARM_CK >= TC_CK + * DSP_CK >= TC_CK + * DSPMMU_CK >= TC_CK + */ + unsigned long realrate; + struct clk * parent; + unsigned dsor_exp; + + if (unlikely(!(clk->flags & RATE_CKCTL))) + return -EINVAL; + + parent = clk->parent; + if (unlikely(parent == 0)) + return -EIO; + + realrate = parent->rate; + for (dsor_exp=0; dsor_exp<4; dsor_exp++) { + if (realrate <= rate) + break; + + realrate /= 2; + } + + return dsor_exp; +} + +static void omap1_ckctl_recalc(struct clk * clk) +{ + int dsor; + + /* Calculate divisor encoded as 2-bit exponent */ + dsor = 1 << (3 & (omap_readw(ARM_CKCTL) >> clk->rate_offset)); + + if (unlikely(clk->rate == clk->parent->rate / dsor)) + return; /* No change, quick exit */ + clk->rate = clk->parent->rate / dsor; + + if (unlikely(clk->flags & RATE_PROPAGATES)) + propagate_rate(clk); +} + +static void omap1_ckctl_recalc_dsp_domain(struct clk * clk) +{ + int dsor; + + /* Calculate divisor encoded as 2-bit exponent + * + * The clock control bits are in DSP domain, + * so api_ck is needed for access. + * Note that DSP_CKCTL virt addr = phys addr, so + * we must use __raw_readw() instead of omap_readw(). + */ + omap1_clk_use(&api_ck.clk); + dsor = 1 << (3 & (__raw_readw(DSP_CKCTL) >> clk->rate_offset)); + omap1_clk_unuse(&api_ck.clk); + + if (unlikely(clk->rate == clk->parent->rate / dsor)) + return; /* No change, quick exit */ + clk->rate = clk->parent->rate / dsor; + + if (unlikely(clk->flags & RATE_PROPAGATES)) + propagate_rate(clk); +} + +/* MPU virtual clock functions */ +static int omap1_select_table_rate(struct clk * clk, unsigned long rate) +{ + /* Find the highest supported frequency <= rate and switch to it */ + struct mpu_rate * ptr; + + if (clk != &virtual_ck_mpu) + return -EINVAL; + + for (ptr = rate_table; ptr->rate; ptr++) { + if (ptr->xtal != ck_ref.rate) + continue; + + /* DPLL1 cannot be reprogrammed without risking system crash */ + if (likely(ck_dpll1.rate!=0) && ptr->pll_rate != ck_dpll1.rate) + continue; + + /* Can check only after xtal frequency check */ + if (ptr->rate <= rate) + break; + } + + if (!ptr->rate) + return -EINVAL; + + /* + * In most cases we should not need to reprogram DPLL. + * Reprogramming the DPLL is tricky, it must be done from SRAM. + */ + omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val); + + ck_dpll1.rate = ptr->pll_rate; + propagate_rate(&ck_dpll1); + return 0; +} + +static int omap1_clk_set_rate_dsp_domain(struct clk *clk, unsigned long rate) +{ + int ret = -EINVAL; + int dsor_exp; + __u16 regval; + + if (clk->flags & RATE_CKCTL) { + dsor_exp = calc_dsor_exp(clk, rate); + if (dsor_exp > 3) + dsor_exp = -EINVAL; + if (dsor_exp < 0) + return dsor_exp; + + regval = __raw_readw(DSP_CKCTL); + regval &= ~(3 << clk->rate_offset); + regval |= dsor_exp << clk->rate_offset; + __raw_writew(regval, DSP_CKCTL); + clk->rate = clk->parent->rate / (1 << dsor_exp); + ret = 0; + } + + if (unlikely(ret == 0 && (clk->flags & RATE_PROPAGATES))) + propagate_rate(clk); + + return ret; +} + +static long omap1_round_to_table_rate(struct clk * clk, unsigned long rate) +{ + /* Find the highest supported frequency <= rate */ + struct mpu_rate * ptr; + long highest_rate; + + if (clk != &virtual_ck_mpu) + return -EINVAL; + + highest_rate = -EINVAL; + + for (ptr = rate_table; ptr->rate; ptr++) { + if (ptr->xtal != ck_ref.rate) + continue; + + highest_rate = ptr->rate; + + /* Can check only after xtal frequency check */ + if (ptr->rate <= rate) + break; + } + + return highest_rate; +} + +static unsigned calc_ext_dsor(unsigned long rate) +{ + unsigned dsor; + + /* MCLK and BCLK divisor selection is not linear: + * freq = 96MHz / dsor + * + * RATIO_SEL range: dsor <-> RATIO_SEL + * 0..6: (RATIO_SEL+2) <-> (dsor-2) + * 6..48: (8+(RATIO_SEL-6)*2) <-> ((dsor-8)/2+6) + * Minimum dsor is 2 and maximum is 96. Odd divisors starting from 9 + * can not be used. + */ + for (dsor = 2; dsor < 96; ++dsor) { + if ((dsor & 1) && dsor > 8) + continue; + if (rate >= 96000000 / dsor) + break; + } + return dsor; +} + +/* Only needed on 1510 */ +static int omap1_set_uart_rate(struct clk * clk, unsigned long rate) +{ + unsigned int val; + + val = omap_readl(clk->enable_reg); + if (rate == 12000000) + val &= ~(1 << clk->enable_bit); + else if (rate == 48000000) + val |= (1 << clk->enable_bit); + else + return -EINVAL; + omap_writel(val, clk->enable_reg); + clk->rate = rate; + + return 0; +} + +/* External clock (MCLK & BCLK) functions */ +static int omap1_set_ext_clk_rate(struct clk * clk, unsigned long rate) +{ + unsigned dsor; + __u16 ratio_bits; + + dsor = calc_ext_dsor(rate); + clk->rate = 96000000 / dsor; + if (dsor > 8) + ratio_bits = ((dsor - 8) / 2 + 6) << 2; + else + ratio_bits = (dsor - 2) << 2; + + ratio_bits |= omap_readw(clk->enable_reg) & ~0xfd; + omap_writew(ratio_bits, clk->enable_reg); + + return 0; +} + +static long omap1_round_ext_clk_rate(struct clk * clk, unsigned long rate) +{ + return 96000000 / calc_ext_dsor(rate); +} + +static void omap1_init_ext_clk(struct clk * clk) +{ + unsigned dsor; + __u16 ratio_bits; + + /* Determine current rate and ensure clock is based on 96MHz APLL */ + ratio_bits = omap_readw(clk->enable_reg) & ~1; + omap_writew(ratio_bits, clk->enable_reg); + + ratio_bits = (ratio_bits & 0xfc) >> 2; + if (ratio_bits > 6) + dsor = (ratio_bits - 6) * 2 + 8; + else + dsor = ratio_bits + 2; + + clk-> rate = 96000000 / dsor; +} + +static int omap1_clk_use(struct clk *clk) +{ + int ret = 0; + if (clk->usecount++ == 0) { + if (likely(clk->parent)) { + ret = omap1_clk_use(clk->parent); + + if (unlikely(ret != 0)) { + clk->usecount--; + return ret; + } + + if (clk->flags & CLOCK_NO_IDLE_PARENT) + if (!cpu_is_omap24xx()) + omap1_clk_deny_idle(clk->parent); + } + + ret = clk->enable(clk); + + if (unlikely(ret != 0) && clk->parent) { + omap1_clk_unuse(clk->parent); + clk->usecount--; + } + } + + return ret; +} + +static void omap1_clk_unuse(struct clk *clk) +{ + if (clk->usecount > 0 && !(--clk->usecount)) { + clk->disable(clk); + if (likely(clk->parent)) { + omap1_clk_unuse(clk->parent); + if (clk->flags & CLOCK_NO_IDLE_PARENT) + if (!cpu_is_omap24xx()) + omap1_clk_allow_idle(clk->parent); + } + } +} + +static int omap1_clk_enable(struct clk *clk) +{ + __u16 regval16; + __u32 regval32; + + if (clk->flags & ALWAYS_ENABLED) + return 0; + + if (unlikely(clk->enable_reg == 0)) { + printk(KERN_ERR "clock.c: Enable for %s without enable code\n", + clk->name); + return 0; + } + + if (clk->flags & ENABLE_REG_32BIT) { + if (clk->flags & VIRTUAL_IO_ADDRESS) { + regval32 = __raw_readl(clk->enable_reg); + regval32 |= (1 << clk->enable_bit); + __raw_writel(regval32, clk->enable_reg); + } else { + regval32 = omap_readl(clk->enable_reg); + regval32 |= (1 << clk->enable_bit); + omap_writel(regval32, clk->enable_reg); + } + } else { + if (clk->flags & VIRTUAL_IO_ADDRESS) { + regval16 = __raw_readw(clk->enable_reg); + regval16 |= (1 << clk->enable_bit); + __raw_writew(regval16, clk->enable_reg); + } else { + regval16 = omap_readw(clk->enable_reg); + regval16 |= (1 << clk->enable_bit); + omap_writew(regval16, clk->enable_reg); + } + } + + return 0; +} + +static void omap1_clk_disable(struct clk *clk) +{ + __u16 regval16; + __u32 regval32; + + if (clk->enable_reg == 0) + return; + + if (clk->flags & ENABLE_REG_32BIT) { + if (clk->flags & VIRTUAL_IO_ADDRESS) { + regval32 = __raw_readl(clk->enable_reg); + regval32 &= ~(1 << clk->enable_bit); + __raw_writel(regval32, clk->enable_reg); + } else { + regval32 = omap_readl(clk->enable_reg); + regval32 &= ~(1 << clk->enable_bit); + omap_writel(regval32, clk->enable_reg); + } + } else { + if (clk->flags & VIRTUAL_IO_ADDRESS) { + regval16 = __raw_readw(clk->enable_reg); + regval16 &= ~(1 << clk->enable_bit); + __raw_writew(regval16, clk->enable_reg); + } else { + regval16 = omap_readw(clk->enable_reg); + regval16 &= ~(1 << clk->enable_bit); + omap_writew(regval16, clk->enable_reg); + } + } +} + +static long omap1_clk_round_rate(struct clk *clk, unsigned long rate) +{ + int dsor_exp; + + if (clk->flags & RATE_FIXED) + return clk->rate; + + if (clk->flags & RATE_CKCTL) { + dsor_exp = calc_dsor_exp(clk, rate); + if (dsor_exp < 0) + return dsor_exp; + if (dsor_exp > 3) + dsor_exp = 3; + return clk->parent->rate / (1 << dsor_exp); + } + + if(clk->round_rate != 0) + return clk->round_rate(clk, rate); + + return clk->rate; +} + +static int omap1_clk_set_rate(struct clk *clk, unsigned long rate) +{ + int ret = -EINVAL; + int dsor_exp; + __u16 regval; + + if (clk->set_rate) + ret = clk->set_rate(clk, rate); + else if (clk->flags & RATE_CKCTL) { + dsor_exp = calc_dsor_exp(clk, rate); + if (dsor_exp > 3) + dsor_exp = -EINVAL; + if (dsor_exp < 0) + return dsor_exp; + + regval = omap_readw(ARM_CKCTL); + regval &= ~(3 << clk->rate_offset); + regval |= dsor_exp << clk->rate_offset; + regval = verify_ckctl_value(regval); + omap_writew(regval, ARM_CKCTL); + clk->rate = clk->parent->rate / (1 << dsor_exp); + ret = 0; + } + + if (unlikely(ret == 0 && (clk->flags & RATE_PROPAGATES))) + propagate_rate(clk); + + return ret; +} + +/*------------------------------------------------------------------------- + * Omap1 clock reset and init functions + *-------------------------------------------------------------------------*/ + +#ifdef CONFIG_OMAP_RESET_CLOCKS +/* + * Resets some clocks that may be left on from bootloader, + * but leaves serial clocks on. See also omap_late_clk_reset(). + */ +static inline void omap1_early_clk_reset(void) +{ + //omap_writel(0x3 << 29, MOD_CONF_CTRL_0); +} + +static int __init omap1_late_clk_reset(void) +{ + /* Turn off all unused clocks */ + struct clk *p; + __u32 regval32; + + /* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */ + regval32 = omap_readw(SOFT_REQ_REG) & (1 << 4); + omap_writew(regval32, SOFT_REQ_REG); + omap_writew(0, SOFT_REQ_REG2); + + list_for_each_entry(p, &clocks, node) { + if (p->usecount > 0 || (p->flags & ALWAYS_ENABLED) || + p->enable_reg == 0) + continue; + + /* Clocks in the DSP domain need api_ck. Just assume bootloader + * has not enabled any DSP clocks */ + if ((u32)p->enable_reg == DSP_IDLECT2) { + printk(KERN_INFO "Skipping reset check for DSP domain " + "clock \"%s\"\n", p->name); + continue; + } + + /* Is the clock already disabled? */ + if (p->flags & ENABLE_REG_32BIT) { + if (p->flags & VIRTUAL_IO_ADDRESS) + regval32 = __raw_readl(p->enable_reg); + else + regval32 = omap_readl(p->enable_reg); + } else { + if (p->flags & VIRTUAL_IO_ADDRESS) + regval32 = __raw_readw(p->enable_reg); + else + regval32 = omap_readw(p->enable_reg); + } + + if ((regval32 & (1 << p->enable_bit)) == 0) + continue; + + /* FIXME: This clock seems to be necessary but no-one + * has asked for its activation. */ + if (p == &tc2_ck // FIX: pm.c (SRAM), CCP, Camera + || p == &ck_dpll1out.clk // FIX: SoSSI, SSR + || p == &arm_gpio_ck // FIX: GPIO code for 1510 + ) { + printk(KERN_INFO "FIXME: Clock \"%s\" seems unused\n", + p->name); + continue; + } + + printk(KERN_INFO "Disabling unused clock \"%s\"... ", p->name); + p->disable(p); + printk(" done\n"); + } + + return 0; +} +late_initcall(omap1_late_clk_reset); + +#else +#define omap1_early_clk_reset() {} +#endif + +static struct clk_functions omap1_clk_functions = { + .clk_use = omap1_clk_use, + .clk_unuse = omap1_clk_unuse, + .clk_round_rate = omap1_clk_round_rate, + .clk_set_rate = omap1_clk_set_rate, +}; + +int __init omap1_clk_init(void) +{ + struct clk ** clkp; + const struct omap_clock_config *info; + int crystal_type = 0; /* Default 12 MHz */ + + omap1_early_clk_reset(); + clk_init(&omap1_clk_functions); + + /* By default all idlect1 clocks are allowed to idle */ + arm_idlect1_mask = ~0; + + for (clkp = onchip_clks; clkp < onchip_clks+ARRAY_SIZE(onchip_clks); clkp++) { + if (((*clkp)->flags &CLOCK_IN_OMAP1510) && cpu_is_omap1510()) { + clk_register(*clkp); + continue; + } + + if (((*clkp)->flags &CLOCK_IN_OMAP16XX) && cpu_is_omap16xx()) { + clk_register(*clkp); + continue; + } + + if (((*clkp)->flags &CLOCK_IN_OMAP730) && cpu_is_omap730()) { + clk_register(*clkp); + continue; + } + } + + info = omap_get_config(OMAP_TAG_CLOCK, struct omap_clock_config); + if (info != NULL) { + if (!cpu_is_omap1510()) + crystal_type = info->system_clock_type; + } + +#if defined(CONFIG_ARCH_OMAP730) + ck_ref.rate = 13000000; +#elif defined(CONFIG_ARCH_OMAP16XX) + if (crystal_type == 2) + ck_ref.rate = 19200000; +#endif + + printk("Clocks: ARM_SYSST: 0x%04x DPLL_CTL: 0x%04x ARM_CKCTL: 0x%04x\n", + omap_readw(ARM_SYSST), omap_readw(DPLL_CTL), + omap_readw(ARM_CKCTL)); + + /* We want to be in syncronous scalable mode */ + omap_writew(0x1000, ARM_SYSST); + +#ifdef CONFIG_OMAP_CLOCKS_SET_BY_BOOTLOADER + /* Use values set by bootloader. Determine PLL rate and recalculate + * dependent clocks as if kernel had changed PLL or divisors. + */ + { + unsigned pll_ctl_val = omap_readw(DPLL_CTL); + + ck_dpll1.rate = ck_ref.rate; /* Base xtal rate */ + if (pll_ctl_val & 0x10) { + /* PLL enabled, apply multiplier and divisor */ + if (pll_ctl_val & 0xf80) + ck_dpll1.rate *= (pll_ctl_val & 0xf80) >> 7; + ck_dpll1.rate /= ((pll_ctl_val & 0x60) >> 5) + 1; + } else { + /* PLL disabled, apply bypass divisor */ + switch (pll_ctl_val & 0xc) { + case 0: + break; + case 0x4: + ck_dpll1.rate /= 2; + break; + default: + ck_dpll1.rate /= 4; + break; + } + } + } + propagate_rate(&ck_dpll1); +#else + /* Find the highest supported frequency and enable it */ + if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) { + printk(KERN_ERR "System frequencies not set. Check your config.\n"); + /* Guess sane values (60MHz) */ + omap_writew(0x2290, DPLL_CTL); + omap_writew(0x1005, ARM_CKCTL); + ck_dpll1.rate = 60000000; + propagate_rate(&ck_dpll1); + } +#endif + /* Cache rates for clocks connected to ck_ref (not dpll1) */ + propagate_rate(&ck_ref); + printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): " + "%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n", + ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10, + ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10, + arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10); + +#ifdef CONFIG_MACH_OMAP_PERSEUS2 + /* Select slicer output as OMAP input clock */ + omap_writew(omap_readw(OMAP730_PCC_UPLD_CTRL) & ~0x1, OMAP730_PCC_UPLD_CTRL); +#endif + + /* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */ + omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL); + + /* Put DSP/MPUI into reset until needed */ + omap_writew(0, ARM_RSTCT1); + omap_writew(1, ARM_RSTCT2); + omap_writew(0x400, ARM_IDLECT1); + + /* + * According to OMAP5910 Erratum SYS_DMA_1, bit DMACK_REQ (bit 8) + * of the ARM_IDLECT2 register must be set to zero. The power-on + * default value of this bit is one. + */ + omap_writew(0x0000, ARM_IDLECT2); /* Turn LCD clock off also */ + + /* + * Only enable those clocks we will need, let the drivers + * enable other clocks as necessary + */ + clk_use(&armper_ck.clk); + clk_use(&armxor_ck.clk); + clk_use(&armtim_ck.clk); /* This should be done by timer code */ + + if (cpu_is_omap1510()) + clk_enable(&arm_gpio_ck); + + return 0; +} + diff --git a/arch/arm/mach-omap1/clock.h b/arch/arm/mach-omap1/clock.h new file mode 100644 index 00000000000..f3bdfb50e01 --- /dev/null +++ b/arch/arm/mach-omap1/clock.h @@ -0,0 +1,768 @@ +/* + * linux/arch/arm/mach-omap1/clock.h + * + * Copyright (C) 2004 - 2005 Nokia corporation + * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com> + * Based on clocks.h by Tony Lindgren, Gordon McNutt and RidgeRun, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ARCH_ARM_MACH_OMAP1_CLOCK_H +#define __ARCH_ARM_MACH_OMAP1_CLOCK_H + +static int omap1_clk_enable(struct clk * clk); +static void omap1_clk_disable(struct clk * clk); +static void omap1_ckctl_recalc(struct clk * clk); +static void omap1_watchdog_recalc(struct clk * clk); +static void omap1_ckctl_recalc_dsp_domain(struct clk * clk); +static int omap1_clk_enable_dsp_domain(struct clk * clk); +static int omap1_clk_set_rate_dsp_domain(struct clk * clk, unsigned long rate); +static void omap1_clk_disable_dsp_domain(struct clk * clk); +static int omap1_set_uart_rate(struct clk * clk, unsigned long rate); +static void omap1_uart_recalc(struct clk * clk); +static int omap1_clk_enable_uart_functional(struct clk * clk); +static void omap1_clk_disable_uart_functional(struct clk * clk); +static int omap1_set_ext_clk_rate(struct clk * clk, unsigned long rate); +static long omap1_round_ext_clk_rate(struct clk * clk, unsigned long rate); +static void omap1_init_ext_clk(struct clk * clk); +static int omap1_select_table_rate(struct clk * clk, unsigned long rate); +static long omap1_round_to_table_rate(struct clk * clk, unsigned long rate); +static int omap1_clk_use(struct clk *clk); +static void omap1_clk_unuse(struct clk *clk); + +struct mpu_rate { + unsigned long rate; + unsigned long xtal; + unsigned long pll_rate; + __u16 ckctl_val; + __u16 dpllctl_val; +}; + +struct uart_clk { + struct clk clk; + unsigned long sysc_addr; +}; + +/* Provide a method for preventing idling some ARM IDLECT clocks */ +struct arm_idlect1_clk { + struct clk clk; + unsigned long no_idle_count; + __u8 idlect_shift; +}; + +/* ARM_CKCTL bit shifts */ +#define CKCTL_PERDIV_OFFSET 0 +#define CKCTL_LCDDIV_OFFSET 2 +#define CKCTL_ARMDIV_OFFSET 4 +#define CKCTL_DSPDIV_OFFSET 6 +#define CKCTL_TCDIV_OFFSET 8 +#define CKCTL_DSPMMUDIV_OFFSET 10 +/*#define ARM_TIMXO 12*/ +#define EN_DSPCK 13 +/*#define ARM_INTHCK_SEL 14*/ /* Divide-by-2 for mpu inth_ck */ +/* DSP_CKCTL bit shifts */ +#define CKCTL_DSPPERDIV_OFFSET 0 + +/* ARM_IDLECT2 bit shifts */ +#define EN_WDTCK 0 +#define EN_XORPCK 1 +#define EN_PERCK 2 +#define EN_LCDCK 3 +#define EN_LBCK 4 /* Not on 1610/1710 */ +/*#define EN_HSABCK 5*/ +#define EN_APICK 6 +#define EN_TIMCK 7 +#define DMACK_REQ 8 +#define EN_GPIOCK 9 /* Not on 1610/1710 */ +/*#define EN_LBFREECK 10*/ +#define EN_CKOUT_ARM 11 + +/* ARM_IDLECT3 bit shifts */ +#define EN_OCPI_CK 0 +#define EN_TC1_CK 2 +#define EN_TC2_CK 4 + +/* DSP_IDLECT2 bit shifts (0,1,2 are same as for ARM_IDLECT2) */ +#define EN_DSPTIMCK 5 + +/* Various register defines for clock controls scattered around OMAP chip */ +#define USB_MCLK_EN_BIT 4 /* In ULPD_CLKC_CTRL */ +#define USB_HOST_HHC_UHOST_EN 9 /* In MOD_CONF_CTRL_0 */ +#define SWD_ULPD_PLL_CLK_REQ 1 /* In SWD_CLK_DIV_CTRL_SEL */ +#define COM_ULPD_PLL_CLK_REQ 1 /* In COM_CLK_DIV_CTRL_SEL */ +#define SWD_CLK_DIV_CTRL_SEL 0xfffe0874 +#define COM_CLK_DIV_CTRL_SEL 0xfffe0878 +#define SOFT_REQ_REG 0xfffe0834 +#define SOFT_REQ_REG2 0xfffe0880 + +/*------------------------------------------------------------------------- + * Omap1 MPU rate table + *-------------------------------------------------------------------------*/ +static struct mpu_rate rate_table[] = { + /* MPU MHz, xtal MHz, dpll1 MHz, CKCTL, DPLL_CTL + * NOTE: Comment order here is different from bits in CKCTL value: + * armdiv, dspdiv, dspmmu, tcdiv, perdiv, lcddiv + */ +#if defined(CONFIG_OMAP_ARM_216MHZ) + { 216000000, 12000000, 216000000, 0x050d, 0x2910 }, /* 1/1/2/2/2/8 */ +#endif +#if defined(CONFIG_OMAP_ARM_195MHZ) + { 195000000, 13000000, 195000000, 0x050e, 0x2790 }, /* 1/1/2/2/4/8 */ +#endif +#if defined(CONFIG_OMAP_ARM_192MHZ) + { 192000000, 19200000, 192000000, 0x050f, 0x2510 }, /* 1/1/2/2/8/8 */ + { 192000000, 12000000, 192000000, 0x050f, 0x2810 }, /* 1/1/2/2/8/8 */ + { 96000000, 12000000, 192000000, 0x055f, 0x2810 }, /* 2/2/2/2/8/8 */ + { 48000000, 12000000, 192000000, 0x0baf, 0x2810 }, /* 4/4/4/8/8/8 */ + { 24000000, 12000000, 192000000, 0x0fff, 0x2810 }, /* 8/8/8/8/8/8 */ +#endif +#if defined(CONFIG_OMAP_ARM_182MHZ) + { 182000000, 13000000, 182000000, 0x050e, 0x2710 }, /* 1/1/2/2/4/8 */ +#endif +#if defined(CONFIG_OMAP_ARM_168MHZ) + { 168000000, 12000000, 168000000, 0x010f, 0x2710 }, /* 1/1/1/2/8/8 */ +#endif +#if defined(CONFIG_OMAP_ARM_150MHZ) + { 150000000, 12000000, 150000000, 0x010a, 0x2cb0 }, /* 1/1/1/2/4/4 */ +#endif +#if defined(CONFIG_OMAP_ARM_120MHZ) + { 120000000, 12000000, 120000000, 0x010a, 0x2510 }, /* 1/1/1/2/4/4 */ +#endif +#if defined(CONFIG_OMAP_ARM_96MHZ) + { 96000000, 12000000, 96000000, 0x0005, 0x2410 }, /* 1/1/1/1/2/2 */ +#endif +#if defined(CONFIG_OMAP_ARM_60MHZ) + { 60000000, 12000000, 60000000, 0x0005, 0x2290 }, /* 1/1/1/1/2/2 */ +#endif +#if defined(CONFIG_OMAP_ARM_30MHZ) + { 30000000, 12000000, 60000000, 0x0555, 0x2290 }, /* 2/2/2/2/2/2 */ +#endif + { 0, 0, 0, 0, 0 }, +}; + +/*------------------------------------------------------------------------- + * Omap1 clocks + *-------------------------------------------------------------------------*/ + +static struct clk ck_ref = { + .name = "ck_ref", + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + ALWAYS_ENABLED, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk ck_dpll1 = { + .name = "ck_dpll1", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_PROPAGATES | ALWAYS_ENABLED, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct arm_idlect1_clk ck_dpll1out = { + .clk = { + .name = "ck_dpll1out", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP16XX | CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_CKOUT_ARM, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 12, +}; + +static struct clk arm_ck = { + .name = "arm_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_CKCTL | RATE_PROPAGATES | ALWAYS_ENABLED, + .rate_offset = CKCTL_ARMDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct arm_idlect1_clk armper_ck = { + .clk = { + .name = "armper_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_CKCTL | CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_PERCK, + .rate_offset = CKCTL_PERDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 2, +}; + +static struct clk arm_gpio_ck = { + .name = "arm_gpio_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_GPIOCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct arm_idlect1_clk armxor_ck = { + .clk = { + .name = "armxor_ck", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_XORPCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 1, +}; + +static struct arm_idlect1_clk armtim_ck = { + .clk = { + .name = "armtim_ck", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_TIMCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 9, +}; + +static struct arm_idlect1_clk armwdt_ck = { + .clk = { + .name = "armwdt_ck", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_WDTCK, + .recalc = &omap1_watchdog_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 0, +}; + +static struct clk arminth_ck16xx = { + .name = "arminth_ck", + .parent = &arm_ck, + .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + /* Note: On 16xx the frequency can be divided by 2 by programming + * ARM_CKCTL:ARM_INTHCK_SEL(14) to 1 + * + * 1510 version is in TC clocks. + */ + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk dsp_ck = { + .name = "dsp_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_CKCTL, + .enable_reg = (void __iomem *)ARM_CKCTL, + .enable_bit = EN_DSPCK, + .rate_offset = CKCTL_DSPDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk dspmmu_ck = { + .name = "dspmmu_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_CKCTL | ALWAYS_ENABLED, + .rate_offset = CKCTL_DSPMMUDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk dspper_ck = { + .name = "dspper_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_CKCTL | VIRTUAL_IO_ADDRESS, + .enable_reg = (void __iomem *)DSP_IDLECT2, + .enable_bit = EN_PERCK, + .rate_offset = CKCTL_PERDIV_OFFSET, + .recalc = &omap1_ckctl_recalc_dsp_domain, + .set_rate = &omap1_clk_set_rate_dsp_domain, + .enable = &omap1_clk_enable_dsp_domain, + .disable = &omap1_clk_disable_dsp_domain, +}; + +static struct clk dspxor_ck = { + .name = "dspxor_ck", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + VIRTUAL_IO_ADDRESS, + .enable_reg = (void __iomem *)DSP_IDLECT2, + .enable_bit = EN_XORPCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable_dsp_domain, + .disable = &omap1_clk_disable_dsp_domain, +}; + +static struct clk dsptim_ck = { + .name = "dsptim_ck", + .parent = &ck_ref, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + VIRTUAL_IO_ADDRESS, + .enable_reg = (void __iomem *)DSP_IDLECT2, + .enable_bit = EN_DSPTIMCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable_dsp_domain, + .disable = &omap1_clk_disable_dsp_domain, +}; + +/* Tie ARM_IDLECT1:IDLIF_ARM to this logical clock structure */ +static struct arm_idlect1_clk tc_ck = { + .clk = { + .name = "tc_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + CLOCK_IN_OMAP730 | RATE_CKCTL | + RATE_PROPAGATES | ALWAYS_ENABLED | + CLOCK_IDLE_CONTROL, + .rate_offset = CKCTL_TCDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 6, +}; + +static struct clk arminth_ck1510 = { + .name = "arminth_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP1510 | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + /* Note: On 1510 the frequency follows TC_CK + * + * 16xx version is in MPU clocks. + */ + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk tipb_ck = { + /* No-idle controlled by "tc_ck" */ + .name = "tibp_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP1510 | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk l3_ocpi_ck = { + /* No-idle controlled by "tc_ck" */ + .name = "l3_ocpi_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX, + .enable_reg = (void __iomem *)ARM_IDLECT3, + .enable_bit = EN_OCPI_CK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk tc1_ck = { + .name = "tc1_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX, + .enable_reg = (void __iomem *)ARM_IDLECT3, + .enable_bit = EN_TC1_CK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk tc2_ck = { + .name = "tc2_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX, + .enable_reg = (void __iomem *)ARM_IDLECT3, + .enable_bit = EN_TC2_CK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk dma_ck = { + /* No-idle controlled by "tc_ck" */ + .name = "dma_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + ALWAYS_ENABLED, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk dma_lcdfree_ck = { + .name = "dma_lcdfree_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct arm_idlect1_clk api_ck = { + .clk = { + .name = "api_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_APICK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 8, +}; + +static struct arm_idlect1_clk lb_ck = { + .clk = { + .name = "lb_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_LBCK, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 4, +}; + +static struct clk rhea1_ck = { + .name = "rhea1_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk rhea2_ck = { + .name = "rhea2_ck", + .parent = &tc_ck.clk, + .flags = CLOCK_IN_OMAP16XX | ALWAYS_ENABLED, + .recalc = &followparent_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk lcd_ck_16xx = { + .name = "lcd_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP16XX | CLOCK_IN_OMAP730 | RATE_CKCTL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_LCDCK, + .rate_offset = CKCTL_LCDDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct arm_idlect1_clk lcd_ck_1510 = { + .clk = { + .name = "lcd_ck", + .parent = &ck_dpll1, + .flags = CLOCK_IN_OMAP1510 | RATE_CKCTL | + CLOCK_IDLE_CONTROL, + .enable_reg = (void __iomem *)ARM_IDLECT2, + .enable_bit = EN_LCDCK, + .rate_offset = CKCTL_LCDDIV_OFFSET, + .recalc = &omap1_ckctl_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, + }, + .idlect_shift = 3, +}; + +static struct clk uart1_1510 = { + .name = "uart1_ck", + /* Direct from ULPD, no real parent */ + .parent = &armper_ck.clk, + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | ENABLE_REG_32BIT | + ALWAYS_ENABLED | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 29, /* Chooses between 12MHz and 48MHz */ + .set_rate = &omap1_set_uart_rate, + .recalc = &omap1_uart_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct uart_clk uart1_16xx = { + .clk = { + .name = "uart1_ck", + /* Direct from ULPD, no real parent */ + .parent = &armper_ck.clk, + .rate = 48000000, + .flags = CLOCK_IN_OMAP16XX | RATE_FIXED | + ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 29, + .enable = &omap1_clk_enable_uart_functional, + .disable = &omap1_clk_disable_uart_functional, + }, + .sysc_addr = 0xfffb0054, +}; + +static struct clk uart2_ck = { + .name = "uart2_ck", + /* Direct from ULPD, no real parent */ + .parent = &armper_ck.clk, + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + ENABLE_REG_32BIT | ALWAYS_ENABLED | + CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 30, /* Chooses between 12MHz and 48MHz */ + .set_rate = &omap1_set_uart_rate, + .recalc = &omap1_uart_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk uart3_1510 = { + .name = "uart3_ck", + /* Direct from ULPD, no real parent */ + .parent = &armper_ck.clk, + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | ENABLE_REG_32BIT | + ALWAYS_ENABLED | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 31, /* Chooses between 12MHz and 48MHz */ + .set_rate = &omap1_set_uart_rate, + .recalc = &omap1_uart_recalc, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct uart_clk uart3_16xx = { + .clk = { + .name = "uart3_ck", + /* Direct from ULPD, no real parent */ + .parent = &armper_ck.clk, + .rate = 48000000, + .flags = CLOCK_IN_OMAP16XX | RATE_FIXED | + ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 31, + .enable = &omap1_clk_enable_uart_functional, + .disable = &omap1_clk_disable_uart_functional, + }, + .sysc_addr = 0xfffb9854, +}; + +static struct clk usb_clko = { /* 6 MHz output on W4_USB_CLKO */ + .name = "usb_clko", + /* Direct from ULPD, no parent */ + .rate = 6000000, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_FIXED | ENABLE_REG_32BIT, + .enable_reg = (void __iomem *)ULPD_CLOCK_CTRL, + .enable_bit = USB_MCLK_EN_BIT, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk usb_hhc_ck1510 = { + .name = "usb_hhc_ck", + /* Direct from ULPD, no parent */ + .rate = 48000000, /* Actually 2 clocks, 12MHz and 48MHz */ + .flags = CLOCK_IN_OMAP1510 | + RATE_FIXED | ENABLE_REG_32BIT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = USB_HOST_HHC_UHOST_EN, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk usb_hhc_ck16xx = { + .name = "usb_hhc_ck", + /* Direct from ULPD, no parent */ + .rate = 48000000, + /* OTG_SYSCON_2.OTG_PADEN == 0 (not 1510-compatible) */ + .flags = CLOCK_IN_OMAP16XX | + RATE_FIXED | ENABLE_REG_32BIT, + .enable_reg = (void __iomem *)OTG_BASE + 0x08 /* OTG_SYSCON_2 */, + .enable_bit = 8 /* UHOST_EN */, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk usb_dc_ck = { + .name = "usb_dc_ck", + /* Direct from ULPD, no parent */ + .rate = 48000000, + .flags = CLOCK_IN_OMAP16XX | RATE_FIXED, + .enable_reg = (void __iomem *)SOFT_REQ_REG, + .enable_bit = 4, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk mclk_1510 = { + .name = "mclk", + /* Direct from ULPD, no parent. May be enabled by ext hardware. */ + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | RATE_FIXED, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk mclk_16xx = { + .name = "mclk", + /* Direct from ULPD, no parent. May be enabled by ext hardware. */ + .flags = CLOCK_IN_OMAP16XX, + .enable_reg = (void __iomem *)COM_CLK_DIV_CTRL_SEL, + .enable_bit = COM_ULPD_PLL_CLK_REQ, + .set_rate = &omap1_set_ext_clk_rate, + .round_rate = &omap1_round_ext_clk_rate, + .init = &omap1_init_ext_clk, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk bclk_1510 = { + .name = "bclk", + /* Direct from ULPD, no parent. May be enabled by ext hardware. */ + .rate = 12000000, + .flags = CLOCK_IN_OMAP1510 | RATE_FIXED, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk bclk_16xx = { + .name = "bclk", + /* Direct from ULPD, no parent. May be enabled by ext hardware. */ + .flags = CLOCK_IN_OMAP16XX, + .enable_reg = (void __iomem *)SWD_CLK_DIV_CTRL_SEL, + .enable_bit = SWD_ULPD_PLL_CLK_REQ, + .set_rate = &omap1_set_ext_clk_rate, + .round_rate = &omap1_round_ext_clk_rate, + .init = &omap1_init_ext_clk, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk mmc1_ck = { + .name = "mmc1_ck", + /* Functional clock is direct from ULPD, interface clock is ARMPER */ + .parent = &armper_ck.clk, + .rate = 48000000, + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + RATE_FIXED | ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 23, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk mmc2_ck = { + .name = "mmc2_ck", + /* Functional clock is direct from ULPD, interface clock is ARMPER */ + .parent = &armper_ck.clk, + .rate = 48000000, + .flags = CLOCK_IN_OMAP16XX | + RATE_FIXED | ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT, + .enable_reg = (void __iomem *)MOD_CONF_CTRL_0, + .enable_bit = 20, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk virtual_ck_mpu = { + .name = "mpu", + .flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | + VIRTUAL_CLOCK | ALWAYS_ENABLED, + .parent = &arm_ck, /* Is smarter alias for */ + .recalc = &followparent_recalc, + .set_rate = &omap1_select_table_rate, + .round_rate = &omap1_round_to_table_rate, + .enable = &omap1_clk_enable, + .disable = &omap1_clk_disable, +}; + +static struct clk * onchip_clks[] = { + /* non-ULPD clocks */ + &ck_ref, + &ck_dpll1, + /* CK_GEN1 clocks */ + &ck_dpll1out.clk, + &arm_ck, + &armper_ck.clk, + &arm_gpio_ck, + &armxor_ck.clk, + &armtim_ck.clk, + &armwdt_ck.clk, + &arminth_ck1510, &arminth_ck16xx, + /* CK_GEN2 clocks */ + &dsp_ck, + &dspmmu_ck, + &dspper_ck, + &dspxor_ck, + &dsptim_ck, + /* CK_GEN3 clocks */ + &tc_ck.clk, + &tipb_ck, + &l3_ocpi_ck, + &tc1_ck, + &tc2_ck, + &dma_ck, + &dma_lcdfree_ck, + &api_ck.clk, + &lb_ck.clk, + &rhea1_ck, + &rhea2_ck, + &lcd_ck_16xx, + &lcd_ck_1510.clk, + /* ULPD clocks */ + &uart1_1510, + &uart1_16xx.clk, + &uart2_ck, + &uart3_1510, + &uart3_16xx.clk, + &usb_clko, + &usb_hhc_ck1510, &usb_hhc_ck16xx, + &usb_dc_ck, + &mclk_1510, &mclk_16xx, + &bclk_1510, &bclk_16xx, + &mmc1_ck, + &mmc2_ck, + /* Virtual clocks */ + &virtual_ck_mpu, +}; + +#endif diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c index 3c5d901efea..ecbc47514ad 100644 --- a/arch/arm/mach-omap1/devices.c +++ b/arch/arm/mach-omap1/devices.c @@ -25,56 +25,7 @@ #include <asm/arch/mux.h> #include <asm/arch/gpio.h> - -static void omap_nop_release(struct device *dev) -{ - /* Nothing */ -} - -/*-------------------------------------------------------------------------*/ - -#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE) - -#define OMAP_I2C_BASE 0xfffb3800 - -static struct resource i2c_resources[] = { - { - .start = OMAP_I2C_BASE, - .end = OMAP_I2C_BASE + 0x3f, - .flags = IORESOURCE_MEM, - }, - { - .start = INT_I2C, - .flags = IORESOURCE_IRQ, - }, -}; - -/* DMA not used; works around erratum writing to non-empty i2c fifo */ - -static struct platform_device omap_i2c_device = { - .name = "i2c_omap", - .id = -1, - .dev = { - .release = omap_nop_release, - }, - .num_resources = ARRAY_SIZE(i2c_resources), - .resource = i2c_resources, -}; - -static void omap_init_i2c(void) -{ - /* FIXME define and use a boot tag, in case of boards that - * either don't wire up I2C, or chips that mux it differently... - * it can include clocking and address info, maybe more. - */ - omap_cfg_reg(I2C_SCL); - omap_cfg_reg(I2C_SDA); - - (void) platform_device_register(&omap_i2c_device); -} -#else -static inline void omap_init_i2c(void) {} -#endif +extern void omap_nop_release(struct device *dev); /*-------------------------------------------------------------------------*/ @@ -110,137 +61,6 @@ static inline void omap_init_irda(void) {} /*-------------------------------------------------------------------------*/ -#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) - -#define OMAP_MMC1_BASE 0xfffb7800 -#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */ - -static struct omap_mmc_conf mmc1_conf; - -static u64 mmc1_dmamask = 0xffffffff; - -static struct resource mmc1_resources[] = { - { - .start = IO_ADDRESS(OMAP_MMC1_BASE), - .end = IO_ADDRESS(OMAP_MMC1_BASE) + 0x7f, - .flags = IORESOURCE_MEM, - }, - { - .start = INT_MMC, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device mmc_omap_device1 = { - .name = "mmci-omap", - .id = 1, - .dev = { - .release = omap_nop_release, - .dma_mask = &mmc1_dmamask, - .platform_data = &mmc1_conf, - }, - .num_resources = ARRAY_SIZE(mmc1_resources), - .resource = mmc1_resources, -}; - -#ifdef CONFIG_ARCH_OMAP16XX - -static struct omap_mmc_conf mmc2_conf; - -static u64 mmc2_dmamask = 0xffffffff; - -static struct resource mmc2_resources[] = { - { - .start = IO_ADDRESS(OMAP_MMC2_BASE), - .end = IO_ADDRESS(OMAP_MMC2_BASE) + 0x7f, - .flags = IORESOURCE_MEM, - }, - { - .start = INT_1610_MMC2, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device mmc_omap_device2 = { - .name = "mmci-omap", - .id = 2, - .dev = { - .release = omap_nop_release, - .dma_mask = &mmc2_dmamask, - .platform_data = &mmc2_conf, - }, - .num_resources = ARRAY_SIZE(mmc2_resources), - .resource = mmc2_resources, -}; -#endif - -static void __init omap_init_mmc(void) -{ - const struct omap_mmc_config *mmc_conf; - const struct omap_mmc_conf *mmc; - - /* NOTE: assumes MMC was never (wrongly) enabled */ - mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config); - if (!mmc_conf) - return; - - /* block 1 is always available and has just one pinout option */ - mmc = &mmc_conf->mmc[0]; - if (mmc->enabled) { - omap_cfg_reg(MMC_CMD); - omap_cfg_reg(MMC_CLK); - omap_cfg_reg(MMC_DAT0); - if (cpu_is_omap1710()) { - omap_cfg_reg(M15_1710_MMC_CLKI); - omap_cfg_reg(P19_1710_MMC_CMDDIR); - omap_cfg_reg(P20_1710_MMC_DATDIR0); - } - if (mmc->wire4) { - omap_cfg_reg(MMC_DAT1); - /* NOTE: DAT2 can be on W10 (here) or M15 */ - if (!mmc->nomux) - omap_cfg_reg(MMC_DAT2); - omap_cfg_reg(MMC_DAT3); - } - mmc1_conf = *mmc; - (void) platform_device_register(&mmc_omap_device1); - } - -#ifdef CONFIG_ARCH_OMAP16XX - /* block 2 is on newer chips, and has many pinout options */ - mmc = &mmc_conf->mmc[1]; - if (mmc->enabled) { - if (!mmc->nomux) { - omap_cfg_reg(Y8_1610_MMC2_CMD); - omap_cfg_reg(Y10_1610_MMC2_CLK); - omap_cfg_reg(R18_1610_MMC2_CLKIN); - omap_cfg_reg(W8_1610_MMC2_DAT0); - if (mmc->wire4) { - omap_cfg_reg(V8_1610_MMC2_DAT1); - omap_cfg_reg(W15_1610_MMC2_DAT2); - omap_cfg_reg(R10_1610_MMC2_DAT3); - } - - /* These are needed for the level shifter */ - omap_cfg_reg(V9_1610_MMC2_CMDDIR); - omap_cfg_reg(V5_1610_MMC2_DATDIR0); - omap_cfg_reg(W19_1610_MMC2_DATDIR1); - } - - /* Feedback clock must be set on OMAP-1710 MMC2 */ - if (cpu_is_omap1710()) - omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24), - MOD_CONF_CTRL_1); - mmc2_conf = *mmc; - (void) platform_device_register(&mmc_omap_device2); - } -#endif - return; -} -#else -static inline void omap_init_mmc(void) {} -#endif - #if defined(CONFIG_OMAP_RTC) || defined(CONFIG_OMAP_RTC) #define OMAP_RTC_BASE 0xfffb4800 @@ -279,38 +99,6 @@ static void omap_init_rtc(void) static inline void omap_init_rtc(void) {} #endif -/*-------------------------------------------------------------------------*/ - -#if defined(CONFIG_OMAP16XX_WATCHDOG) || defined(CONFIG_OMAP16XX_WATCHDOG_MODULE) - -#define OMAP_WDT_BASE 0xfffeb000 - -static struct resource wdt_resources[] = { - { - .start = OMAP_WDT_BASE, - .end = OMAP_WDT_BASE + 0x4f, - .flags = IORESOURCE_MEM, - }, -}; - -static struct platform_device omap_wdt_device = { - .name = "omap1610_wdt", - .id = -1, - .dev = { - .release = omap_nop_release, - }, - .num_resources = ARRAY_SIZE(wdt_resources), - .resource = wdt_resources, -}; - -static void omap_init_wdt(void) -{ - (void) platform_device_register(&omap_wdt_device); -} -#else -static inline void omap_init_wdt(void) {} -#endif - /*-------------------------------------------------------------------------*/ @@ -334,18 +122,15 @@ static inline void omap_init_wdt(void) {} * may be handled by the boot loader, and drivers should expect it will * normally have been done by the time they're probed. */ -static int __init omap_init_devices(void) +static int __init omap1_init_devices(void) { /* please keep these calls, and their implementations above, * in alphabetical order so they're easier to sort through. */ - omap_init_i2c(); omap_init_irda(); - omap_init_mmc(); omap_init_rtc(); - omap_init_wdt(); return 0; } -arch_initcall(omap_init_devices); +arch_initcall(omap1_init_devices); diff --git a/arch/arm/mach-omap1/id.c b/arch/arm/mach-omap1/id.c index 986c3b7e09b..5c637c04836 100644 --- a/arch/arm/mach-omap1/id.c +++ b/arch/arm/mach-omap1/id.c @@ -18,6 +18,13 @@ #include <asm/io.h> +#define OMAP_DIE_ID_0 0xfffe1800 +#define OMAP_DIE_ID_1 0xfffe1804 +#define OMAP_PRODUCTION_ID_0 0xfffe2000 +#define OMAP_PRODUCTION_ID_1 0xfffe2004 +#define OMAP32_ID_0 0xfffed400 +#define OMAP32_ID_1 0xfffed404 + struct omap_id { u16 jtag_id; /* Used to determine OMAP type */ u8 die_rev; /* Processor revision */ @@ -27,6 +34,7 @@ struct omap_id { /* Register values to detect the OMAP version */ static struct omap_id omap_ids[] __initdata = { + { .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000}, { .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100}, { .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300}, { .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000}, @@ -164,6 +172,7 @@ void __init omap_check_revision(void) case 0x07: system_rev |= 0x07; break; + case 0x03: case 0x15: system_rev |= 0x15; break; diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c index 79fb86535eb..a7a19f75b9e 100644 --- a/arch/arm/mach-omap1/io.c +++ b/arch/arm/mach-omap1/io.c @@ -15,9 +15,10 @@ #include <asm/mach/map.h> #include <asm/io.h> +#include <asm/arch/mux.h> #include <asm/arch/tc.h> -extern int clk_init(void); +extern int omap1_clk_init(void); extern void omap_check_revision(void); extern void omap_sram_init(void); @@ -50,7 +51,7 @@ static struct map_desc omap730_io_desc[] __initdata = { }; #endif -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX static struct map_desc omap1510_io_desc[] __initdata = { { .virtual = OMAP1510_DSP_BASE, @@ -98,7 +99,7 @@ static void __init _omap_map_io(void) iotable_init(omap730_io_desc, ARRAY_SIZE(omap730_io_desc)); } #endif -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { iotable_init(omap1510_io_desc, ARRAY_SIZE(omap1510_io_desc)); } @@ -119,7 +120,7 @@ static void __init _omap_map_io(void) /* Must init clocks early to assure that timer interrupt works */ - clk_init(); + omap1_clk_init(); } /* @@ -127,7 +128,9 @@ static void __init _omap_map_io(void) */ void __init omap_map_common_io(void) { - if (!initialized) + if (!initialized) { _omap_map_io(); + omap1_mux_init(); + } } diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c index 192ce6055fa..ed65a7d2e94 100644 --- a/arch/arm/mach-omap1/irq.c +++ b/arch/arm/mach-omap1/irq.c @@ -47,6 +47,7 @@ #include <asm/irq.h> #include <asm/mach/irq.h> #include <asm/arch/gpio.h> +#include <asm/arch/cpu.h> #include <asm/io.h> @@ -147,11 +148,15 @@ static struct omap_irq_bank omap730_irq_banks[] = { }; #endif -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX static struct omap_irq_bank omap1510_irq_banks[] = { { .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3febfff }, { .base_reg = OMAP_IH2_BASE, .trigger_map = 0xffbfffed }, }; +static struct omap_irq_bank omap310_irq_banks[] = { + { .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3faefc3 }, + { .base_reg = OMAP_IH2_BASE, .trigger_map = 0x65b3c061 }, +}; #endif #if defined(CONFIG_ARCH_OMAP16XX) @@ -181,11 +186,15 @@ void __init omap_init_irq(void) irq_bank_count = ARRAY_SIZE(omap730_irq_banks); } #endif -#ifdef CONFIG_ARCH_OMAP1510 +#ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { irq_banks = omap1510_irq_banks; irq_bank_count = ARRAY_SIZE(omap1510_irq_banks); } + if (cpu_is_omap310()) { + irq_banks = omap310_irq_banks; + irq_bank_count = ARRAY_SIZE(omap310_irq_banks); + } #endif #if defined(CONFIG_ARCH_OMAP16XX) if (cpu_is_omap16xx()) { @@ -226,9 +235,11 @@ void __init omap_init_irq(void) } /* Unmask level 2 handler */ - if (cpu_is_omap730()) { + + if (cpu_is_omap730()) omap_unmask_irq(INT_730_IH2_IRQ); - } else { - omap_unmask_irq(INT_IH2_IRQ); - } + else if (cpu_is_omap1510()) + omap_unmask_irq(INT_1510_IH2_IRQ); + else if (cpu_is_omap16xx()) + omap_unmask_irq(INT_1610_IH2_IRQ); } diff --git a/arch/arm/mach-omap1/leds-h2p2-debug.c b/arch/arm/mach-omap1/leds-h2p2-debug.c index 399010c1403..65065081591 100644 --- a/arch/arm/mach-omap1/leds-h2p2-debug.c +++ b/arch/arm/mach-omap1/leds-h2p2-debug.c @@ -18,6 +18,7 @@ #include <asm/hardware.h> #include <asm/leds.h> #include <asm/system.h> +#include <asm/mach-types.h> #include <asm/arch/fpga.h> #include <asm/arch/gpio.h> @@ -63,14 +64,19 @@ void h2p2_dbg_leds_event(led_event_t evt) case led_stop: case led_halted: /* all leds off during suspend or shutdown */ - omap_set_gpio_dataout(GPIO_TIMER, 0); - omap_set_gpio_dataout(GPIO_IDLE, 0); + + if (! machine_is_omap_perseus2()) { + omap_set_gpio_dataout(GPIO_TIMER, 0); + omap_set_gpio_dataout(GPIO_IDLE, 0); + } + __raw_writew(~0, &fpga->leds); led_state &= ~LED_STATE_ENABLED; if (evt == led_halted) { iounmap(fpga); fpga = NULL; } + goto done; case led_claim: @@ -85,18 +91,37 @@ void h2p2_dbg_leds_event(led_event_t evt) #ifdef CONFIG_LEDS_TIMER case led_timer: led_state ^= LED_TIMER_ON; - omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON); - goto done; + + if (machine_is_omap_perseus2()) + hw_led_state ^= H2P2_DBG_FPGA_P2_LED_TIMER; + else { + omap_set_gpio_dataout(GPIO_TIMER, led_state & LED_TIMER_ON); + goto done; + } + + break; #endif #ifdef CONFIG_LEDS_CPU case led_idle_start: - omap_set_gpio_dataout(GPIO_IDLE, 1); - goto done; + if (machine_is_omap_perseus2()) + hw_led_state |= H2P2_DBG_FPGA_P2_LED_IDLE; + else { + omap_set_gpio_dataout(GPIO_IDLE, 1); + goto done; + } + + break; case led_idle_end: - omap_set_gpio_dataout(GPIO_IDLE, 0); - goto done; + if (machine_is_omap_perseus2()) + hw_led_state &= ~H2P2_DBG_FPGA_P2_LED_IDLE; + else { + omap_set_gpio_dataout(GPIO_IDLE, 0); + goto done; + } + + break; #endif case led_green_on: @@ -135,7 +160,7 @@ void h2p2_dbg_leds_event(led_event_t evt) /* * Actually burn the LEDs */ - if (led_state & LED_STATE_CLAIMED) + if (led_state & LED_STATE_ENABLED) __raw_writew(~hw_led_state, &fpga->leds); done: diff --git a/arch/arm/mach-omap1/leds.c b/arch/arm/mach-omap1/leds.c index 5c6b1bb6e72..3f9dcac4fd4 100644 --- a/arch/arm/mach-omap1/leds.c +++ b/arch/arm/mach-omap1/leds.c @@ -33,7 +33,6 @@ omap_leds_init(void) if (machine_is_omap_h2() || machine_is_omap_h3() - || machine_is_omap_perseus2() #ifdef CONFIG_OMAP_OSK_MISTRAL || machine_is_omap_osk() #endif diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c new file mode 100644 index 00000000000..d4b8d624e74 --- /dev/null +++ b/arch/arm/mach-omap1/mux.c @@ -0,0 +1,289 @@ +/* + * linux/arch/arm/mach-omap1/mux.c + * + * OMAP1 pin multiplexing configurations + * + * Copyright (C) 2003 - 2005 Nokia Corporation + * + * Written by Tony Lindgren <tony.lindgren@nokia.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ +#include <linux/config.h> +#include <linux/module.h> +#include <linux/init.h> +#include <asm/system.h> +#include <asm/io.h> +#include <linux/spinlock.h> + +#include <asm/arch/mux.h> + +#ifdef CONFIG_OMAP_MUX + +#ifdef CONFIG_ARCH_OMAP730 +struct pin_config __initdata_or_module omap730_pins[] = { +MUX_CFG_730("E2_730_KBR0", 12, 21, 0, 0, 20, 1, NA, 0, 0) +MUX_CFG_730("J7_730_KBR1", 12, 25, 0, 0, 24, 1, NA, 0, 0) +MUX_CFG_730("E1_730_KBR2", 12, 29, 0, 0, 28, 1, NA, 0, 0) +MUX_CFG_730("F3_730_KBR3", 13, 1, 0, 0, 0, 1, NA, 0, 0) +MUX_CFG_730("D2_730_KBR4", 13, 5, 0, 0, 4, 1, NA, 0, 0) +MUX_CFG_730("C2_730_KBC0", 13, 9, 0, 0, 8, 1, NA, 0, 0) +MUX_CFG_730("D3_730_KBC1", 13, 13, 0, 0, 12, 1, NA, 0, 0) +MUX_CFG_730("E4_730_KBC2", 13, 17, 0, 0, 16, 1, NA, 0, 0) +MUX_CFG_730("F4_730_KBC3", 13, 21, 0, 0, 20, 1, NA, 0, 0) +MUX_CFG_730("E3_730_KBC4", 13, 25, 0, 0, 24, 1, NA, 0, 0) +}; +#endif + +#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) +struct pin_config __initdata_or_module omap1xxx_pins[] = { +/* + * description mux mode mux pull pull pull pu_pd pu dbg + * reg offset mode reg bit ena reg + */ +MUX_CFG("UART1_TX", 9, 21, 1, 2, 3, 0, NA, 0, 0) +MUX_CFG("UART1_RTS", 9, 12, 1, 2, 0, 0, NA, 0, 0) + +/* UART2 (COM_UART_GATING), conflicts with USB2 */ +MUX_CFG("UART2_TX", C, 27, 1, 3, 3, 0, NA, 0, 0) +MUX_CFG("UART2_RX", C, 18, 0, 3, 1, 1, NA, 0, 0) +MUX_CFG("UART2_CTS", C, 21, 0, 3, 1, 1, NA, 0, 0) +MUX_CFG("UART2_RTS", C, 24, 1, 3, 2, 0, NA, 0, 0) + +/* UART3 (GIGA_UART_GATING) */ +MUX_CFG("UART3_TX", 6, 0, 1, 0, 30, 0, NA, 0, 0) +MUX_CFG("UART3_RX", 6, 3, 0, 0, 31, 1, NA, 0, 0) +MUX_CFG("UART3_CTS", 5, 12, 2, 0, 24, 0, NA, 0, 0) +MUX_CFG("UART3_RTS", 5, 15, 2, 0, 25, 0, NA, 0, 0) +MUX_CFG("UART3_CLKREQ", 9, 27, 0, 2, 5, 0, NA, 0, 0) +MUX_CFG("UART3_BCLK", A, 0, 0, 2, 6, 0, NA, 0, 0) +MUX_CFG("Y15_1610_UART3_RTS", A, 0, 1, 2, 6, 0, NA, 0, 0) + +/* PWT & PWL, conflicts with UART3 */ +MUX_CFG("PWT", 6, 0, 2, 0, 30, 0, NA, 0, 0) +MUX_CFG("PWL", 6, 3, 1, 0, 31, 1, NA, 0, 0) + +/* USB internal master generic */ +MUX_CFG("R18_USB_VBUS", 7, 9, 2, 1, 11, 0, NA, 0, 1) +MUX_CFG("R18_1510_USB_GPIO0", 7, 9, 0, 1, 11, 1, NA, 0, 1) +/* works around erratum: W4_USB_PUEN and W4_USB_PUDIS are switched! */ +MUX_CFG("W4_USB_PUEN", D, 3, 3, 3, 5, 1, NA, 0, 1) +MUX_CFG("W4_USB_CLKO", D, 3, 1, 3, 5, 0, NA, 0, 1) +MUX_CFG("W4_USB_HIGHZ", D, 3, 4, 3, 5, 0, 3, 0, 1) +MUX_CFG("W4_GPIO58", D, 3, 7, 3, 5, 0, 3, 0, 1) + +/* USB1 master */ +MUX_CFG("USB1_SUSP", 8, 27, 2, 1, 27, 0, NA, 0, 1) +MUX_CFG("USB1_SE0", 9, 0, 2, 1, 28, 0, NA, 0, 1) +MUX_CFG("W13_1610_USB1_SE0", 9, 0, 4, 1, 28, 0, NA, 0, 1) +MUX_CFG("USB1_TXEN", 9, 3, 2, 1, 29, 0, NA, 0, 1) +MUX_CFG("USB1_TXD", 9, 24, 1, 2, 4, 0, NA, 0, 1) +MUX_CFG("USB1_VP", A, 3, 1, 2, 7, 0, NA, 0, 1) +MUX_CFG("USB1_VM", A, 6, 1, 2, 8, 0, NA, 0, 1) +MUX_CFG("USB1_RCV", A, 9, 1, 2, 9, 0, NA, 0, 1) +MUX_CFG("USB1_SPEED", A, 12, 2, 2, 10, 0, NA, 0, 1) +MUX_CFG("R13_1610_USB1_SPEED", A, 12, 5, 2, 10, 0, NA, 0, 1) +MUX_CFG("R13_1710_USB1_SEO", A, 12, 5, 2, 10, 0, NA, 0, 1) + +/* USB2 master */ +MUX_CFG("USB2_SUSP", B, 3, 1, 2, 17, 0, NA, 0, 1) +MUX_CFG("USB2_VP", B, 6, 1, 2, 18, 0, NA, 0, 1) +MUX_CFG("USB2_TXEN", B, 9, 1, 2, 19, 0, NA, 0, 1) +MUX_CFG("USB2_VM", C, 18, 1, 3, 0, 0, NA, 0, 1) +MUX_CFG("USB2_RCV", C, 21, 1, 3, 1, 0, NA, 0, 1) +MUX_CFG("USB2_SE0", C, 24, 2, 3, 2, 0, NA, 0, 1) +MUX_CFG("USB2_TXD", C, 27, 2, 3, 3, 0, NA, 0, 1) + +/* OMAP-1510 GPIO */ +MUX_CFG("R18_1510_GPIO0", 7, 9, 0, 1, 11, 1, 0, 0, 1) +MUX_CFG("R19_1510_GPIO1", 7, 6, 0, 1, 10, 1, 0, 0, 1) +MUX_CFG("M14_1510_GPIO2", 7, 3, 0, 1, 9, 1, 0, 0, 1) + +/* OMAP1610 GPIO */ +MUX_CFG("P18_1610_GPIO3", 7, 0, 0, 1, 8, 0, NA, 0, 1) +MUX_CFG("Y15_1610_GPIO17", A, 0, 7, 2, 6, 0, NA, 0, 1) + +/* OMAP-1710 GPIO */ +MUX_CFG("R18_1710_GPIO0", 7, 9, 0, 1, 11, 1, 1, 1, 1) +MUX_CFG("V2_1710_GPIO10", F, 27, 1, 4, 3, 1, 4, 1, 1) +MUX_CFG("N21_1710_GPIO14", 6, 9, 0, 1, 1, 1, 1, 1, 1) +MUX_CFG("W15_1710_GPIO40", 9, 27, 7, 2, 5, 1, 2, 1, 1) + +/* MPUIO */ +MUX_CFG("MPUIO2", 7, 18, 0, 1, 14, 1, NA, 0, 1) +MUX_CFG("N15_1610_MPUIO2", 7, 18, 0, 1, 14, 1, 1, 0, 1) +MUX_CFG("MPUIO4", 7, 15, 0, 1, 13, 1, NA, 0, 1) +MUX_CFG("MPUIO5", 7, 12, 0, 1, 12, 1, NA, 0, 1) + +MUX_CFG("T20_1610_MPUIO5", 7, 12, 0, 1, 12, 0, 3, 0, 1) +MUX_CFG("W11_1610_MPUIO6", 10, 15, 2, 3, 8, 0, 3, 0, 1) +MUX_CFG("V10_1610_MPUIO7", A, 24, 2, 2, 14, 0, 2, 0, 1) +MUX_CFG("W11_1610_MPUIO9", 10, 15, 1, 3, 8, 0, 3, 0, 1) +MUX_CFG("V10_1610_MPUIO10", A, 24, 1, 2, 14, 0, 2, 0, 1) +MUX_CFG("W10_1610_MPUIO11", A, 18, 2, 2, 11, 0, 2, 0, 1) +MUX_CFG("E20_1610_MPUIO13", 3, 21, 1, 0, 7, 0, 0, 0, 1) +MUX_CFG("U20_1610_MPUIO14", 9, 6, 6, 0, 30, 0, 0, 0, 1) +MUX_CFG("E19_1610_MPUIO15", 3, 18, 1, 0, 6, 0, 0, 0, 1) + +/* MCBSP2 */ +MUX_CFG("MCBSP2_CLKR", C, 6, 0, 2, 27, 1, NA, 0, 1) +MUX_CFG("MCBSP2_CLKX", C, 9, 0, 2, 29, 1, NA, 0, 1) +MUX_CFG("MCBSP2_DR", C, 0, 0, 2, 26, 1, NA, 0, 1) +MUX_CFG("MCBSP2_DX", C, 15, 0, 2, 31, 1, NA, 0, 1) +MUX_CFG("MCBSP2_FSR", C, 12, 0, 2, 30, 1, NA, 0, 1) +MUX_CFG("MCBSP2_FSX", C, 3, 0, 2, 27, 1, NA, 0, 1) + +/* MCBSP3 NOTE: Mode must 1 for clock */ +MUX_CFG("MCBSP3_CLKX", 9, 3, 1, 1, 29, 0, NA, 0, 1) + +/* Misc ballouts */ +MUX_CFG("BALLOUT_V8_ARMIO3", B, 18, 0, 2, 25, 1, NA, 0, 1) +MUX_CFG("N20_HDQ", 6, 18, 1, 1, 4, 0, 1, 4, 0) + +/* OMAP-1610 MMC2 */ +MUX_CFG("W8_1610_MMC2_DAT0", B, 21, 6, 2, 23, 1, 2, 1, 1) +MUX_CFG("V8_1610_MMC2_DAT1", B, 27, 6, 2, 25, 1, 2, 1, 1) +MUX_CFG("W15_1610_MMC2_DAT2", 9, 12, 6, 2, 5, 1, 2, 1, 1) +MUX_CFG("R10_1610_MMC2_DAT3", B, 18, 6, 2, 22, 1, 2, 1, 1) +MUX_CFG("Y10_1610_MMC2_CLK", B, 3, 6, 2, 17, 0, 2, 0, 1) +MUX_CFG("Y8_1610_MMC2_CMD", B, 24, 6, 2, 24, 1, 2, 1, 1) +MUX_CFG("V9_1610_MMC2_CMDDIR", B, 12, 6, 2, 20, 0, 2, 1, 1) +MUX_CFG("V5_1610_MMC2_DATDIR0", B, 15, 6, 2, 21, 0, 2, 1, 1) +MUX_CFG("W19_1610_MMC2_DATDIR1", 8, 15, 6, 1, 23, 0, 1, 1, 1) +MUX_CFG("R18_1610_MMC2_CLKIN", 7, 9, 6, 1, 11, 0, 1, 11, 1) + +/* OMAP-1610 External Trace Interface */ +MUX_CFG("M19_1610_ETM_PSTAT0", 5, 27, 1, 0, 29, 0, 0, 0, 1) +MUX_CFG("L15_1610_ETM_PSTAT1", 5, 24, 1, 0, 28, 0, 0, 0, 1) +MUX_CFG("L18_1610_ETM_PSTAT2", 5, 21, 1, 0, 27, 0, 0, 0, 1) +MUX_CFG("L19_1610_ETM_D0", 5, 18, 1, 0, 26, 0, 0, 0, 1) +MUX_CFG("J19_1610_ETM_D6", 5, 0, 1, 0, 20, 0, 0, 0, 1) +MUX_CFG("J18_1610_ETM_D7", 5, 27, 1, 0, 19, 0, 0, 0, 1) + +/* OMAP16XX GPIO */ +MUX_CFG("P20_1610_GPIO4", 6, 27, 0, 1, 7, 0, 1, 1, 1) +MUX_CFG("V9_1610_GPIO7", B, 12, 1, 2, 20, 0, 2, 1, 1) +MUX_CFG("W8_1610_GPIO9", B, 21, 0, 2, 23, 0, 2, 1, 1) +MUX_CFG("N20_1610_GPIO11", 6, 18, 0, 1, 4, 0, 1, 1, 1) +MUX_CFG("N19_1610_GPIO13", 6, 12, 0, 1, 2, 0, 1, 1, 1) +MUX_CFG("P10_1610_GPIO22", C, 0, 7, 2, 26, 0, 2, 1, 1) +MUX_CFG("V5_1610_GPIO24", B, 15, 7, 2, 21, 0, 2, 1, 1) +MUX_CFG("AA20_1610_GPIO_41", 9, 9, 7, 1, 31, 0, 1, 1, 1) +MUX_CFG("W19_1610_GPIO48", 8, 15, 7, 1, 23, 1, 1, 0, 1) +MUX_CFG("M7_1610_GPIO62", 10, 0, 0, 4, 24, 0, 4, 0, 1) +MUX_CFG("V14_16XX_GPIO37", 9, 18, 7, 2, 2, 0, 2, 2, 0) +MUX_CFG("R9_16XX_GPIO18", C, 18, 7, 3, 0, 0, 3, 0, 0) +MUX_CFG("L14_16XX_GPIO49", 6, 3, 7, 0, 31, 0, 0, 31, 0) + +/* OMAP-1610 uWire */ +MUX_CFG("V19_1610_UWIRE_SCLK", 8, 6, 0, 1, 20, 0, 1, 1, 1) +MUX_CFG("U18_1610_UWIRE_SDI", 8, 0, 0, 1, 18, 0, 1, 1, 1) +MUX_CFG("W21_1610_UWIRE_SDO", 8, 3, 0, 1, 19, 0, 1, 1, 1) +MUX_CFG("N14_1610_UWIRE_CS0", 8, 9, 1, 1, 21, 0, 1, 1, 1) +MUX_CFG("P15_1610_UWIRE_CS3", 8, 12, 1, 1, 22, 0, 1, 1, 1) +MUX_CFG("N15_1610_UWIRE_CS1", 7, 18, 2, 1, 14, 0, NA, 0, 1) + +/* OMAP-1610 Flash */ +MUX_CFG("L3_1610_FLASH_CS2B_OE",10, 6, 1, NA, 0, 0, NA, 0, 1) +MUX_CFG("M8_1610_FLASH_CS2B_WE",10, 3, 1, NA, 0, 0, NA, 0, 1) + +/* First MMC interface, same on 1510, 1610 and 1710 */ +MUX_CFG("MMC_CMD", A, 27, 0, 2, 15, 1, 2, 1, 1) +MUX_CFG("MMC_DAT1", A, 24, 0, 2, 14, 1, 2, 1, 1) +MUX_CFG("MMC_DAT2", A, 18, 0, 2, 12, 1, 2, 1, 1) +MUX_CFG("MMC_DAT0", B, 0, 0, 2, 16, 1, 2, 1, 1) +MUX_CFG("MMC_CLK", A, 21, 0, NA, 0, 0, NA, 0, 1) +MUX_CFG("MMC_DAT3", 10, 15, 0, 3, 8, 1, 3, 1, 1) +MUX_CFG("M15_1710_MMC_CLKI", 6, 21, 2, 0, 0, 0, NA, 0, 1) +MUX_CFG("P19_1710_MMC_CMDDIR", 6, 24, 6, 0, 0, 0, NA, 0, 1) +MUX_CFG("P20_1710_MMC_DATDIR0", 6, 27, 5, 0, 0, 0, NA, 0, 1) + +/* OMAP-1610 USB0 alternate configuration */ +MUX_CFG("W9_USB0_TXEN", B, 9, 5, 2, 19, 0, 2, 0, 1) +MUX_CFG("AA9_USB0_VP", B, 6, 5, 2, 18, 0, 2, 0, 1) +MUX_CFG("Y5_USB0_RCV", C, 21, 5, 3, 1, 0, 1, 0, 1) +MUX_CFG("R9_USB0_VM", C, 18, 5, 3, 0, 0, 3, 0, 1) +MUX_CFG("V6_USB0_TXD", C, 27, 5, 3, 3, 0, 3, 0, 1) +MUX_CFG("W5_USB0_SE0", C, 24, 5, 3, 2, 0, 3, 0, 1) +MUX_CFG("V9_USB0_SPEED", B, 12, 5, 2, 20, 0, 2, 0, 1) +MUX_CFG("Y10_USB0_SUSP", B, 3, 5, 2, 17, 0, 2, 0, 1) + +/* USB2 interface */ +MUX_CFG("W9_USB2_TXEN", B, 9, 1, NA, 0, 0, NA, 0, 1) +MUX_CFG("AA9_USB2_VP", B, 6, 1, NA, 0, 0, NA, 0, 1) +MUX_CFG("Y5_USB2_RCV", C, 21, 1, NA, 0, 0, NA, 0, 1) +MUX_CFG("R9_USB2_VM", C, 18, 1, NA, 0, 0, NA, 0, 1) +MUX_CFG("V6_USB2_TXD", C, 27, 2, NA, 0, 0, NA, 0, 1) +MUX_CFG("W5_USB2_SE0", C, 24, 2, NA, 0, 0, NA, 0, 1) + +/* 16XX UART */ +MUX_CFG("R13_1610_UART1_TX", A, 12, 6, 2, 10, 0, 2, 10, 1) +MUX_CFG("V14_16XX_UART1_RX", 9, 18, 0, 2, 2, 0, 2, 2, 1) +MUX_CFG("R14_1610_UART1_CTS", 9, 15, 0, 2, 1, 0, 2, 1, 1) +MUX_CFG("AA15_1610_UART1_RTS", 9, 12, 1, 2, 0, 0, 2, 0, 1) +MUX_CFG("R9_16XX_UART2_RX", C, 18, 0, 3, 0, 0, 3, 0, 1) +MUX_CFG("L14_16XX_UART3_RX", 6, 3, 0, 0, 31, 0, 0, 31, 1) + +/* I2C interface */ +MUX_CFG("I2C_SCL", 7, 24, 0, NA, 0, 0, NA, 0, 0) +MUX_CFG("I2C_SDA", 7, 27, 0, NA, 0, 0, NA, 0, 0) + +/* Keypad */ +MUX_CFG("F18_1610_KBC0", 3, 15, 0, 0, 5, 1, 0, 0, 0) +MUX_CFG("D20_1610_KBC1", 3, 12, 0, 0, 4, 1, 0, 0, 0) +MUX_CFG("D19_1610_KBC2", 3, 9, 0, 0, 3, 1, 0, 0, 0) +MUX_CFG("E18_1610_KBC3", 3, 6, 0, 0, 2, 1, 0, 0, 0) +MUX_CFG("C21_1610_KBC4", 3, 3, 0, 0, 1, 1, 0, 0, 0) +MUX_CFG("G18_1610_KBR0", 4, 0, 0, 0, 10, 1, 0, 1, 0) +MUX_CFG("F19_1610_KBR1", 3, 27, 0, 0, 9, 1, 0, 1, 0) +MUX_CFG("H14_1610_KBR2", 3, 24, 0, 0, 8, 1, 0, 1, 0) +MUX_CFG("E20_1610_KBR3", 3, 21, 0, 0, 7, 1, 0, 1, 0) +MUX_CFG("E19_1610_KBR4", 3, 18, 0, 0, 6, 1, 0, 1, 0) +MUX_CFG("N19_1610_KBR5", 6, 12, 1, 1, 2, 1, 1, 1, 0) + +/* Power management */ +MUX_CFG("T20_1610_LOW_PWR", 7, 12, 1, NA, 0, 0, NA, 0, 0) + +/* MCLK Settings */ +MUX_CFG("V5_1710_MCLK_ON", B, 15, 0, NA, 0, 0, NA, 0, 0) +MUX_CFG("V5_1710_MCLK_OFF", B, 15, 6, NA, 0, 0, NA, 0, 0) +MUX_CFG("R10_1610_MCLK_ON", B, 18, 0, NA, 22, 0, NA, 1, 0) +MUX_CFG("R10_1610_MCLK_OFF", B, 18, 6, 2, 22, 1, 2, 1, 1) + +/* CompactFlash controller, conflicts with MMC1 */ +MUX_CFG("P11_1610_CF_CD2", A, 27, 3, 2, 15, 1, 2, 1, 1) +MUX_CFG("R11_1610_CF_IOIS16", B, 0, 3, 2, 16, 1, 2, 1, 1) +MUX_CFG("V10_1610_CF_IREQ", A, 24, 3, 2, 14, 0, 2, 0, 1) +MUX_CFG("W10_1610_CF_RESET", A, 18, 3, 2, 12, 1, 2, 1, 1) +MUX_CFG("W11_1610_CF_CD1", 10, 15, 3, 3, 8, 1, 3, 1, 1) +}; +#endif /* CONFIG_ARCH_OMAP15XX || CONFIG_ARCH_OMAP16XX */ + +int __init omap1_mux_init(void) +{ + +#ifdef CONFIG_ARCH_OMAP730 + omap_mux_register(omap730_pins, ARRAY_SIZE(omap730_pins)); +#endif + +#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX) + omap_mux_register(omap1xxx_pins, ARRAY_SIZE(omap1xxx_pins)); +#endif + + return 0; +} + +#endif diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c index 40c4f7c40e7..6810cfb8446 100644 --- a/arch/arm/mach-omap1/serial.c +++ b/arch/arm/mach-omap1/serial.c @@ -109,9 +109,10 @@ static struct platform_device serial_device = { * By default UART2 does not work on Innovator-1510 if you have * USB OHCI enabled. To use UART2, you must disable USB2 first. */ -void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS]) +void __init omap_serial_init(void) { int i; + const struct omap_uart_config *info; if (cpu_is_omap730()) { serial_platform_data[0].regshift = 0; @@ -126,10 +127,14 @@ void __init omap_serial_init(int ports[OMAP_MAX_NR_PORTS]) serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16; } + info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config); + if (info == NULL) + return; + for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { unsigned char reg; - if (ports[i] == 0) { + if (!((1 << i) & info->enabled_uarts)) { serial_platform_data[i].membase = NULL; serial_platform_data[i].mapbase = 0; continue; diff --git a/arch/arm/mach-omap1/time.c b/arch/arm/mach-omap1/time.c index 191a9b1ee9b..cdbf4d7620c 100644 --- a/arch/arm/mach-omap1/time.c +++ b/arch/arm/mach-omap1/time.c @@ -226,8 +226,8 @@ unsigned long long sched_clock(void) #ifdef CONFIG_OMAP_32K_TIMER -#ifdef CONFIG_ARCH_OMAP1510 -#error OMAP 32KHz timer does not currently work on 1510! +#ifdef CONFIG_ARCH_OMAP15XX +#error OMAP 32KHz timer does not currently work on 15XX! #endif /* |