diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-3430sdp.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-3430sdp.c | 132 |
1 files changed, 23 insertions, 109 deletions
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 7ffad7bfb82..52dbdf3ab66 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -19,7 +19,6 @@ #include <linux/input.h> #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> #include <linux/i2c/twl.h> #include <linux/regulator/machine.h> #include <linux/io.h> @@ -48,6 +47,7 @@ #include "hsmmc.h" #include "pm.h" #include "control.h" +#include "common-board-devices.h" #define CONFIG_DISABLE_HFCLK 1 @@ -105,63 +105,14 @@ static struct twl4030_keypad_data sdp3430_kp_data = { .rep = 1, }; -static int ts_gpio; /* Needed for ads7846_get_pendown_state */ - -/** - * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq - * - * @return - void. If request gpio fails then Flag KERN_ERR. - */ -static void ads7846_dev_init(void) -{ - if (gpio_request(ts_gpio, "ADS7846 pendown") < 0) { - printk(KERN_ERR "can't get ads746 pen down GPIO\n"); - return; - } - - gpio_direction_input(ts_gpio); - gpio_set_debounce(ts_gpio, 310); -} - -static int ads7846_get_pendown_state(void) -{ - return !gpio_get_value(ts_gpio); -} - -static struct ads7846_platform_data tsc2046_config __initdata = { - .get_pendown_state = ads7846_get_pendown_state, - .keep_vref_on = 1, - .wakeup = true, -}; - - -static struct omap2_mcspi_device_config tsc2046_mcspi_config = { - .turbo_mode = 0, - .single_channel = 1, /* 0: slave, 1: master */ -}; - -static struct spi_board_info sdp3430_spi_board_info[] __initdata = { - [0] = { - /* - * TSC2046 operates at a max freqency of 2MHz, so - * operate slightly below at 1.5MHz - */ - .modalias = "ads7846", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 1500000, - .controller_data = &tsc2046_mcspi_config, - .irq = 0, - .platform_data = &tsc2046_config, - }, -}; - - #define SDP3430_LCD_PANEL_BACKLIGHT_GPIO 8 #define SDP3430_LCD_PANEL_ENABLE_GPIO 5 -static unsigned backlight_gpio; -static unsigned enable_gpio; +static struct gpio sdp3430_dss_gpios[] __initdata = { + {SDP3430_LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD reset" }, + {SDP3430_LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD Backlight"}, +}; + static int lcd_enabled; static int dvi_enabled; @@ -169,29 +120,11 @@ static void __init sdp3430_display_init(void) { int r; - enable_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO; - backlight_gpio = SDP3430_LCD_PANEL_BACKLIGHT_GPIO; - - r = gpio_request(enable_gpio, "LCD reset"); - if (r) { - printk(KERN_ERR "failed to get LCD reset GPIO\n"); - goto err0; - } - - r = gpio_request(backlight_gpio, "LCD Backlight"); - if (r) { - printk(KERN_ERR "failed to get LCD backlight GPIO\n"); - goto err1; - } + r = gpio_request_array(sdp3430_dss_gpios, + ARRAY_SIZE(sdp3430_dss_gpios)); + if (r) + printk(KERN_ERR "failed to get LCD control GPIOs\n"); - gpio_direction_output(enable_gpio, 0); - gpio_direction_output(backlight_gpio, 0); - - return; -err1: - gpio_free(enable_gpio); -err0: - return; } static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev) @@ -201,8 +134,8 @@ static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev) return -EINVAL; } - gpio_direction_output(enable_gpio, 1); - gpio_direction_output(backlight_gpio, 1); + gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 1); + gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 1); lcd_enabled = 1; @@ -213,8 +146,8 @@ static void sdp3430_panel_disable_lcd(struct omap_dss_device *dssdev) { lcd_enabled = 0; - gpio_direction_output(enable_gpio, 0); - gpio_direction_output(backlight_gpio, 0); + gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 0); + gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 0); } static int sdp3430_panel_enable_dvi(struct omap_dss_device *dssdev) @@ -342,12 +275,10 @@ static int sdp3430_twl_gpio_setup(struct device *dev, omap2_hsmmc_init(mmc); /* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */ - gpio_request(gpio + 7, "sub_lcd_en_bkl"); - gpio_direction_output(gpio + 7, 0); + gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl"); /* gpio + 15 is "sub_lcd_nRST" (output) */ - gpio_request(gpio + 15, "sub_lcd_nRST"); - gpio_direction_output(gpio + 15, 0); + gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST"); return 0; } @@ -562,20 +493,10 @@ static struct twl4030_platform_data sdp3430_twldata = { .vpll2 = &sdp3430_vpll2, }; -static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("twl4030", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &sdp3430_twldata, - }, -}; - static int __init omap3430_i2c_init(void) { /* i2c1 for PMIC only */ - omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo, - ARRAY_SIZE(sdp3430_i2c_boardinfo)); + omap3_pmic_init("twl4030", &sdp3430_twldata); /* i2c2 on camera connector (for sensor control) and optional isp1301 */ omap_register_i2c_bus(2, 400, NULL, 0); /* i2c3 on display connector (for DVI, tfp410) */ @@ -854,29 +775,22 @@ static struct flash_partitions sdp_flash_partitions[] = { }, }; -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, -}; - static void __init omap_3430sdp_init(void) { + int gpio_pendown; + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap_board_config = sdp3430_config; omap_board_config_size = ARRAY_SIZE(sdp3430_config); omap3430_i2c_init(); omap_display_init(&sdp3430_dss_data); if (omap_rev() > OMAP3430_REV_ES1_0) - ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV2; + gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV2; else - ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV1; - sdp3430_spi_board_info[0].irq = gpio_to_irq(ts_gpio); - spi_register_board_info(sdp3430_spi_board_info, - ARRAY_SIZE(sdp3430_spi_board_info)); - ads7846_dev_init(); + gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1; + omap_ads7846_init(1, gpio_pendown, 310, NULL); board_serial_init(); - usb_musb_init(&musb_board_data); + usb_musb_init(NULL); board_smc91x_init(); board_flash_init(sdp_flash_partitions, chip_sel_3430, 0); sdp3430_display_init(); |