diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-cm-t35.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-cm-t35.c | 242 |
1 files changed, 41 insertions, 201 deletions
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index 02a12b41c0f..77456dec93e 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -45,8 +45,8 @@ #include <plat/nand.h> #include <plat/gpmc.h> #include <plat/usb.h> -#include <plat/display.h> -#include <plat/panel-generic-dpi.h> +#include <video/omapdss.h> +#include <video/omap-panel-generic-dpi.h> #include <plat/mcspi.h> #include <mach/hardware.h> @@ -54,6 +54,7 @@ #include "mux.h" #include "sdram-micron-mt46h32m32lf-6.h" #include "hsmmc.h" +#include "common-board-devices.h" #define CM_T35_GPIO_PENDOWN 57 @@ -62,90 +63,30 @@ #define SB_T35_SMSC911X_CS 4 #define SB_T35_SMSC911X_GPIO 65 -#define NAND_BLOCK_SIZE SZ_128K - #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include <linux/smsc911x.h> +#include <plat/gpmc-smsc911x.h> -static struct smsc911x_platform_config cm_t35_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, - .phy_interface = PHY_INTERFACE_MODE_MII, -}; - -static struct resource cm_t35_smsc911x_resources[] = { - { - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO), - .end = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct platform_device cm_t35_smsc911x_device = { - .name = "smsc911x", +static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = { .id = 0, - .num_resources = ARRAY_SIZE(cm_t35_smsc911x_resources), - .resource = cm_t35_smsc911x_resources, - .dev = { - .platform_data = &cm_t35_smsc911x_config, - }, -}; - -static struct resource sb_t35_smsc911x_resources[] = { - { - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO), - .end = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO), - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, + .cs = CM_T35_SMSC911X_CS, + .gpio_irq = CM_T35_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; -static struct platform_device sb_t35_smsc911x_device = { - .name = "smsc911x", +static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = { .id = 1, - .num_resources = ARRAY_SIZE(sb_t35_smsc911x_resources), - .resource = sb_t35_smsc911x_resources, - .dev = { - .platform_data = &cm_t35_smsc911x_config, - }, + .cs = SB_T35_SMSC911X_CS, + .gpio_irq = SB_T35_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, }; -static void __init cm_t35_init_smsc911x(struct platform_device *dev, - int cs, int irq_gpio) -{ - unsigned long cs_mem_base; - - if (gpmc_cs_request(cs, SZ_16M, &cs_mem_base) < 0) { - pr_err("CM-T35: Failed request for GPMC mem for smsc911x\n"); - return; - } - - dev->resource[0].start = cs_mem_base + 0x0; - dev->resource[0].end = cs_mem_base + 0xff; - - if ((gpio_request(irq_gpio, "ETH IRQ") == 0) && - (gpio_direction_input(irq_gpio) == 0)) { - gpio_export(irq_gpio, 0); - } else { - pr_err("CM-T35: could not obtain gpio for SMSC911X IRQ\n"); - return; - } - - platform_device_register(dev); -} - static void __init cm_t35_init_ethernet(void) { - cm_t35_init_smsc911x(&cm_t35_smsc911x_device, - CM_T35_SMSC911X_CS, CM_T35_SMSC911X_GPIO); - cm_t35_init_smsc911x(&sb_t35_smsc911x_device, - SB_T35_SMSC911X_CS, SB_T35_SMSC911X_GPIO); + gpmc_smsc911x_init(&cm_t35_smsc911x_cfg); + gpmc_smsc911x_init(&sb_t35_smsc911x_cfg); } #else static inline void __init cm_t35_init_ethernet(void) { return; } @@ -235,69 +176,10 @@ static void __init cm_t35_init_nand(void) static inline void cm_t35_init_nand(void) {} #endif -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \ - defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -#include <linux/spi/ads7846.h> - -static struct omap2_mcspi_device_config ads7846_mcspi_config = { - .turbo_mode = 0, - .single_channel = 1, /* 0: slave, 1: master */ -}; - -static int ads7846_get_pendown_state(void) -{ - return !gpio_get_value(CM_T35_GPIO_PENDOWN); -} - -static struct ads7846_platform_data ads7846_config = { - .x_max = 0x0fff, - .y_max = 0x0fff, - .x_plate_ohms = 180, - .pressure_max = 255, - .debounce_max = 10, - .debounce_tol = 3, - .debounce_rep = 1, - .get_pendown_state = ads7846_get_pendown_state, - .keep_vref_on = 1, -}; - -static struct spi_board_info cm_t35_spi_board_info[] __initdata = { - { - .modalias = "ads7846", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 1500000, - .controller_data = &ads7846_mcspi_config, - .irq = OMAP_GPIO_IRQ(CM_T35_GPIO_PENDOWN), - .platform_data = &ads7846_config, - }, -}; - -static void __init cm_t35_init_ads7846(void) -{ - if ((gpio_request(CM_T35_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) && - (gpio_direction_input(CM_T35_GPIO_PENDOWN) == 0)) { - gpio_export(CM_T35_GPIO_PENDOWN, 0); - } else { - pr_err("CM-T35: could not obtain gpio for ADS7846_PENDOWN\n"); - return; - } - - spi_register_board_info(cm_t35_spi_board_info, - ARRAY_SIZE(cm_t35_spi_board_info)); -} -#else -static inline void cm_t35_init_ads7846(void) {} -#endif - #define CM_T35_LCD_EN_GPIO 157 #define CM_T35_LCD_BL_GPIO 58 #define CM_T35_DVI_EN_GPIO 54 -static int lcd_bl_gpio; -static int lcd_en_gpio; -static int dvi_en_gpio; - static int lcd_enabled; static int dvi_enabled; @@ -308,8 +190,8 @@ static int cm_t35_panel_enable_lcd(struct omap_dss_device *dssdev) return -EINVAL; } - gpio_set_value(lcd_en_gpio, 1); - gpio_set_value(lcd_bl_gpio, 1); + gpio_set_value(CM_T35_LCD_EN_GPIO, 1); + gpio_set_value(CM_T35_LCD_BL_GPIO, 1); lcd_enabled = 1; @@ -320,8 +202,8 @@ static void cm_t35_panel_disable_lcd(struct omap_dss_device *dssdev) { lcd_enabled = 0; - gpio_set_value(lcd_bl_gpio, 0); - gpio_set_value(lcd_en_gpio, 0); + gpio_set_value(CM_T35_LCD_BL_GPIO, 0); + gpio_set_value(CM_T35_LCD_EN_GPIO, 0); } static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev) @@ -331,7 +213,7 @@ static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev) return -EINVAL; } - gpio_set_value(dvi_en_gpio, 0); + gpio_set_value(CM_T35_DVI_EN_GPIO, 0); dvi_enabled = 1; return 0; @@ -339,7 +221,7 @@ static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev) static void cm_t35_panel_disable_dvi(struct omap_dss_device *dssdev) { - gpio_set_value(dvi_en_gpio, 1); + gpio_set_value(CM_T35_DVI_EN_GPIO, 1); dvi_enabled = 0; } @@ -421,62 +303,38 @@ static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = { }, }; +static struct gpio cm_t35_dss_gpios[] __initdata = { + { CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW, "lcd enable" }, + { CM_T35_LCD_BL_GPIO, GPIOF_OUT_INIT_LOW, "lcd bl enable" }, + { CM_T35_DVI_EN_GPIO, GPIOF_OUT_INIT_HIGH, "dvi enable" }, +}; + static void __init cm_t35_init_display(void) { int err; - lcd_en_gpio = CM_T35_LCD_EN_GPIO; - lcd_bl_gpio = CM_T35_LCD_BL_GPIO; - dvi_en_gpio = CM_T35_DVI_EN_GPIO; - spi_register_board_info(cm_t35_lcd_spi_board_info, ARRAY_SIZE(cm_t35_lcd_spi_board_info)); - err = gpio_request(lcd_en_gpio, "LCD RST"); - if (err) { - pr_err("CM-T35: failed to get LCD reset GPIO\n"); - goto out; - } - - err = gpio_request(lcd_bl_gpio, "LCD BL"); + err = gpio_request_array(cm_t35_dss_gpios, + ARRAY_SIZE(cm_t35_dss_gpios)); if (err) { - pr_err("CM-T35: failed to get LCD backlight control GPIO\n"); - goto err_lcd_bl; - } - - err = gpio_request(dvi_en_gpio, "DVI EN"); - if (err) { - pr_err("CM-T35: failed to get DVI reset GPIO\n"); - goto err_dvi_en; + pr_err("CM-T35: failed to request DSS control GPIOs\n"); + return; } - gpio_export(lcd_en_gpio, 0); - gpio_export(lcd_bl_gpio, 0); - gpio_export(dvi_en_gpio, 0); - gpio_direction_output(lcd_en_gpio, 0); - gpio_direction_output(lcd_bl_gpio, 0); - gpio_direction_output(dvi_en_gpio, 1); + gpio_export(CM_T35_LCD_EN_GPIO, 0); + gpio_export(CM_T35_LCD_BL_GPIO, 0); + gpio_export(CM_T35_DVI_EN_GPIO, 0); msleep(50); - gpio_set_value(lcd_en_gpio, 1); + gpio_set_value(CM_T35_LCD_EN_GPIO, 1); err = omap_display_init(&cm_t35_dss_data); if (err) { pr_err("CM-T35: failed to register DSS device\n"); - goto err_dev_reg; + gpio_free_array(cm_t35_dss_gpios, ARRAY_SIZE(cm_t35_dss_gpios)); } - - return; - -err_dev_reg: - gpio_free(dvi_en_gpio); -err_dvi_en: - gpio_free(lcd_bl_gpio); -err_lcd_bl: - gpio_free(lcd_en_gpio); -out: - - return; } static struct regulator_consumer_supply cm_t35_vmmc1_supply = { @@ -609,10 +467,8 @@ static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio, { int wlan_rst = gpio + 2; - if ((gpio_request(wlan_rst, "WLAN RST") == 0) && - (gpio_direction_output(wlan_rst, 1) == 0)) { + if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) { gpio_export(wlan_rst, 0); - udelay(10); gpio_set_value(wlan_rst, 0); udelay(10); @@ -653,19 +509,9 @@ static struct twl4030_platform_data cm_t35_twldata = { .vpll2 = &cm_t35_vpll2, }; -static struct i2c_board_info __initdata cm_t35_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("tps65930", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &cm_t35_twldata, - }, -}; - static void __init cm_t35_init_i2c(void) { - omap_register_i2c_bus(1, 2600, cm_t35_i2c_boardinfo, - ARRAY_SIZE(cm_t35_i2c_boardinfo)); + omap3_pmic_init("tps65930", &cm_t35_twldata); } static void __init cm_t35_init_early(void) @@ -775,12 +621,6 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, -}; - static struct omap_board_config_kernel cm_t35_config[] __initdata = { }; @@ -792,12 +632,12 @@ static void __init cm_t35_init(void) omap_serial_init(); cm_t35_init_i2c(); cm_t35_init_nand(); - cm_t35_init_ads7846(); + omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL); cm_t35_init_ethernet(); cm_t35_init_led(); cm_t35_init_display(); - usb_musb_init(&musb_board_data); + usb_musb_init(NULL); usbhs_init(&usbhs_bdata); } |