diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-igep0020.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-igep0020.c | 103 |
1 files changed, 80 insertions, 23 deletions
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index ea7cbc69f7c..0d6d583e8b3 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -55,6 +55,11 @@ #define IGEP2_RC_GPIO_WIFI_NRESET 139 #define IGEP2_RC_GPIO_BT_NRESET 137 +#define IGEP3_GPIO_LED0_GREEN 54 +#define IGEP3_GPIO_LED0_RED 53 +#define IGEP3_GPIO_LED1_RED 16 +#define IGEP3_GPIO_USBH_NRESET 183 + /* * IGEP2 Hardware Revision Table * @@ -69,6 +74,7 @@ #define IGEP2_BOARD_HWREV_B 0 #define IGEP2_BOARD_HWREV_C 1 +#define IGEP3_BOARD_HWREV 2 static u8 hwrev; @@ -76,6 +82,11 @@ static void __init igep2_get_revision(void) { u8 ret; + if (machine_is_igep0030()) { + hwrev = IGEP3_BOARD_HWREV; + return; + } + omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT); if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) { @@ -332,24 +343,40 @@ static struct platform_device igep_led_device = { static void __init igep_leds_init(void) { - igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED; - igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN; - igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED; + if (machine_is_igep0020()) { + igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED; + igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN; + igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED; + } else { + igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED; + igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN; + igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED; + } platform_device_register(&igep_led_device); } #else static struct gpio igep_gpio_leds[] __initdata = { - { IGEP2_GPIO_LED0_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" }, - { IGEP2_GPIO_LED0_GREEN, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" }, - { IGEP2_GPIO_LED1_RED, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" }, + { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" }, + { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" }, + { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" }, }; static inline void igep_leds_init(void) { int i; + if (machine_is_igep0020()) { + igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED; + igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN; + igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED; + } else { + igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED; + igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN; + igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED; + } + if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) { pr_warning("IGEP v2: Could not obtain leds gpios\n"); return; @@ -386,6 +413,9 @@ static int igep_twl_gpio_setup(struct device *dev, igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1; #endif + if (machine_is_igep0030()) + return 0; + /* * REVISIT: need ehci-omap hooks for external VBUS * power switch and overcurrent detect @@ -548,18 +578,20 @@ static void __init igep_i2c_init(void) { int ret; - /* - * Bus 3 is attached to the DVI port where devices like the pico DLP - * projector don't work reliably with 400kHz - */ - ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo, - ARRAY_SIZE(igep2_i2c3_boardinfo)); - if (ret) - pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret); - - igep_twldata.codec = &igep2_codec_data; - igep_twldata.keypad = &igep2_keypad_pdata; - igep_twldata.vpll2 = &igep2_vpll2; + if (machine_is_igep0020()) { + /* + * Bus 3 is attached to the DVI port where devices like the + * pico DLP projector don't work reliably with 400kHz + */ + ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo, + ARRAY_SIZE(igep2_i2c3_boardinfo)); + if (ret) + pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret); + + igep_twldata.codec = &igep2_codec_data; + igep_twldata.keypad = &igep2_keypad_pdata; + igep_twldata.vpll2 = &igep2_vpll2; + } omap3_pmic_init("twl4030", &igep_twldata); } @@ -575,6 +607,17 @@ static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = { .reset_gpio_port[2] = -EINVAL, }; +static const struct usbhs_omap_board_data igep3_usbhs_bdata __initconst = { + .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, + .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, + .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, + + .phy_reset = true, + .reset_gpio_port[0] = -EINVAL, + .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET, + .reset_gpio_port[2] = -EINVAL, +}; + #ifdef CONFIG_OMAP_MUX static struct omap_board_mux board_mux[] __initdata = { { .reg_offset = OMAP_MUX_TERMINATOR }, @@ -597,7 +640,7 @@ static void __init igep_wlan_bt_init(void) igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD; igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET; igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET; - } else if (hwrev == IGEP2_BOARD_HWREV_C) { + } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) { igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD; igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET; igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET; @@ -645,10 +688,14 @@ static void __init igep_init(void) */ igep_wlan_bt_init(); - omap_display_init(&igep2_dss_data); - igep2_display_init(); - igep2_init_smsc911x(); - usbhs_init(&igep2_usbhs_bdata); + if (machine_is_igep0020()) { + omap_display_init(&igep2_dss_data); + igep2_display_init(); + igep2_init_smsc911x(); + usbhs_init(&igep2_usbhs_bdata); + } else { + usbhs_init(&igep3_usbhs_bdata); + } } MACHINE_START(IGEP0020, "IGEP v2 board") @@ -660,3 +707,13 @@ MACHINE_START(IGEP0020, "IGEP v2 board") .init_machine = igep_init, .timer = &omap_timer, MACHINE_END + +MACHINE_START(IGEP0030, "IGEP OMAP3 module") + .boot_params = 0x80000100, + .reserve = omap_reserve, + .map_io = omap3_map_io, + .init_early = igep_init_early, + .init_irq = omap_init_irq, + .init_machine = igep_init, + .timer = &omap_timer, +MACHINE_END |