diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-omap3stalker.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3stalker.c | 137 |
1 files changed, 18 insertions, 119 deletions
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index a6e0b9161c9..0c108a212ea 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -39,13 +39,12 @@ #include <plat/gpmc.h> #include <plat/nand.h> #include <plat/usb.h> -#include <plat/display.h> -#include <plat/panel-generic-dpi.h> +#include <video/omapdss.h> +#include <video/omap-panel-generic-dpi.h> #include <plat/mcspi.h> #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> -#include <linux/spi/ads7846.h> #include <linux/interrupt.h> #include <linux/smsc911x.h> #include <linux/i2c/at24.h> @@ -54,52 +53,28 @@ #include "mux.h" #include "hsmmc.h" #include "timer-gp.h" +#include "common-board-devices.h" #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) +#include <plat/gpmc-smsc911x.h> + #define OMAP3STALKER_ETHR_START 0x2c000000 #define OMAP3STALKER_ETHR_SIZE 1024 #define OMAP3STALKER_ETHR_GPIO_IRQ 19 #define OMAP3STALKER_SMC911X_CS 5 -static struct resource omap3stalker_smsc911x_resources[] = { - [0] = { - .start = OMAP3STALKER_ETHR_START, - .end = - (OMAP3STALKER_ETHR_START + OMAP3STALKER_ETHR_SIZE - 1), - .flags = IORESOURCE_MEM, - }, - [1] = { - .start = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ), - .end = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ), - .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW), - }, -}; - -static struct smsc911x_platform_config smsc911x_config = { - .phy_interface = PHY_INTERFACE_MODE_MII, - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, +static struct omap_smsc911x_platform_data smsc911x_cfg = { + .cs = OMAP3STALKER_SMC911X_CS, + .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ, + .gpio_reset = -EINVAL, .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS), }; -static struct platform_device omap3stalker_smsc911x_device = { - .name = "smsc911x", - .id = -1, - .num_resources = ARRAY_SIZE(omap3stalker_smsc911x_resources), - .resource = &omap3stalker_smsc911x_resources[0], - .dev = { - .platform_data = &smsc911x_config, - }, -}; - static inline void __init omap3stalker_init_eth(void) { - int eth_cs; struct clk *l3ck; unsigned int rate; - eth_cs = OMAP3STALKER_SMC911X_CS; - l3ck = clk_get(NULL, "l3_ck"); if (IS_ERR(l3ck)) rate = 100000000; @@ -107,16 +82,7 @@ static inline void __init omap3stalker_init_eth(void) rate = clk_get_rate(l3ck); omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP); - if (gpio_request(OMAP3STALKER_ETHR_GPIO_IRQ, "SMC911x irq") < 0) { - printk(KERN_ERR - "Failed to request GPIO%d for smc911x IRQ\n", - OMAP3STALKER_ETHR_GPIO_IRQ); - return; - } - - gpio_direction_input(OMAP3STALKER_ETHR_GPIO_IRQ); - - platform_device_register(&omap3stalker_smsc911x_device); + gpmc_smsc911x_init(&smsc911x_cfg); } #else @@ -365,12 +331,11 @@ omap3stalker_twl_gpio_setup(struct device *dev, */ /* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */ - gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL"); - gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0); + gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW, + "EN_LCD_BKL"); /* gpio + 7 == DVI Enable */ - gpio_request(gpio + 7, "EN_DVI"); - gpio_direction_output(gpio + 7, 0); + gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI"); /* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; @@ -489,15 +454,8 @@ static struct twl4030_platform_data omap3stalker_twldata = { .codec = &omap3stalker_codec_data, .vdac = &omap3_stalker_vdac, .vpll2 = &omap3_stalker_vpll2, -}; - -static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("twl4030", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &omap3stalker_twldata, - }, + .vmmc1 = &omap3stalker_vmmc1, + .vsim = &omap3stalker_vsim, }; static struct at24_platform_data fram_info = { @@ -516,15 +474,7 @@ static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = { static int __init omap3_stalker_i2c_init(void) { - /* - * REVISIT: These entries can be set in omap3evm_twl_data - * after a merge with MFD tree - */ - omap3stalker_twldata.vmmc1 = &omap3stalker_vmmc1; - omap3stalker_twldata.vsim = &omap3stalker_vsim; - - omap_register_i2c_bus(1, 2600, omap3stalker_i2c_boardinfo, - ARRAY_SIZE(omap3stalker_i2c_boardinfo)); + omap3_pmic_init("twl4030", &omap3stalker_twldata); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3, ARRAY_SIZE(omap3stalker_i2c_boardinfo3)); @@ -532,49 +482,6 @@ static int __init omap3_stalker_i2c_init(void) } #define OMAP3_STALKER_TS_GPIO 175 -static void ads7846_dev_init(void) -{ - if (gpio_request(OMAP3_STALKER_TS_GPIO, "ADS7846 pendown") < 0) - printk(KERN_ERR "can't get ads7846 pen down GPIO\n"); - - gpio_direction_input(OMAP3_STALKER_TS_GPIO); - gpio_set_debounce(OMAP3_STALKER_TS_GPIO, 310); -} - -static int ads7846_get_pendown_state(void) -{ - return !gpio_get_value(OMAP3_STALKER_TS_GPIO); -} - -static struct ads7846_platform_data ads7846_config = { - .x_max = 0x0fff, - .y_max = 0x0fff, - .x_plate_ohms = 180, - .pressure_max = 255, - .debounce_max = 10, - .debounce_tol = 3, - .debounce_rep = 1, - .get_pendown_state = ads7846_get_pendown_state, - .keep_vref_on = 1, - .settle_delay_usecs = 150, -}; - -static struct omap2_mcspi_device_config ads7846_mcspi_config = { - .turbo_mode = 0, - .single_channel = 1, /* 0: slave, 1: master */ -}; - -static struct spi_board_info omap3stalker_spi_board_info[] = { - [0] = { - .modalias = "ads7846", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 1500000, - .controller_data = &ads7846_mcspi_config, - .irq = OMAP_GPIO_IRQ(OMAP3_STALKER_TS_GPIO), - .platform_data = &ads7846_config, - }, -}; static struct omap_board_config_kernel omap3_stalker_config[] __initdata = { }; @@ -618,12 +525,6 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, -}; - static void __init omap3_stalker_init(void) { omap3_mux_init(board_mux, OMAP_PACKAGE_CUS); @@ -636,13 +537,11 @@ static void __init omap3_stalker_init(void) ARRAY_SIZE(omap3_stalker_devices)); omap_display_init(&omap3_stalker_dss_data); - spi_register_board_info(omap3stalker_spi_board_info, - ARRAY_SIZE(omap3stalker_spi_board_info)); omap_serial_init(); - usb_musb_init(&musb_board_data); + usb_musb_init(NULL); usbhs_init(&usbhs_bdata); - ads7846_dev_init(); + omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL); omap_mux_init_gpio(21, OMAP_PIN_OUTPUT); omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP); |