diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-overo.c')
-rw-r--r-- | arch/arm/mach-omap2/board-overo.c | 265 |
1 files changed, 46 insertions, 219 deletions
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 9d192ff3b9a..1555918e3ff 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -56,6 +56,7 @@ #include "mux.h" #include "sdram-micron-mt46h32m32lf-6.h" #include "hsmmc.h" +#include "common-board-devices.h" #define OVERO_GPIO_BT_XGATE 15 #define OVERO_GPIO_W2W_NRESET 16 @@ -74,30 +75,6 @@ #if defined(CONFIG_TOUCHSCREEN_ADS7846) || \ defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -#include <linux/spi/ads7846.h> - -static struct omap2_mcspi_device_config ads7846_mcspi_config = { - .turbo_mode = 0, - .single_channel = 1, /* 0: slave, 1: master */ -}; - -static int ads7846_get_pendown_state(void) -{ - return !gpio_get_value(OVERO_GPIO_PENDOWN); -} - -static struct ads7846_platform_data ads7846_config = { - .x_max = 0x0fff, - .y_max = 0x0fff, - .x_plate_ohms = 180, - .pressure_max = 255, - .debounce_max = 10, - .debounce_tol = 3, - .debounce_rep = 1, - .get_pendown_state = ads7846_get_pendown_state, - .keep_vref_on = 1, -}; - /* fixed regulator for ads7846 */ static struct regulator_consumer_supply ads7846_supply = REGULATOR_SUPPLY("vcc", "spi1.0"); @@ -128,14 +105,7 @@ static struct platform_device vads7846_device = { static void __init overo_ads7846_init(void) { - if ((gpio_request(OVERO_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) && - (gpio_direction_input(OVERO_GPIO_PENDOWN) == 0)) { - gpio_export(OVERO_GPIO_PENDOWN, 0); - } else { - printk(KERN_ERR "could not obtain gpio for ADS7846_PENDOWN\n"); - return; - } - + omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL); platform_device_register(&vads7846_device); } @@ -146,106 +116,28 @@ static inline void __init overo_ads7846_init(void) { return; } #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE) #include <linux/smsc911x.h> +#include <plat/gpmc-smsc911x.h> -static struct resource overo_smsc911x_resources[] = { - { - .name = "smsc911x-memory", - .flags = IORESOURCE_MEM, - }, - { - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct resource overo_smsc911x2_resources[] = { - { - .name = "smsc911x2-memory", - .flags = IORESOURCE_MEM, - }, - { - .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, - }, -}; - -static struct smsc911x_platform_config overo_smsc911x_config = { - .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, - .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, - .flags = SMSC911X_USE_32BIT , - .phy_interface = PHY_INTERFACE_MODE_MII, -}; - -static struct platform_device overo_smsc911x_device = { - .name = "smsc911x", +static struct omap_smsc911x_platform_data smsc911x_cfg = { .id = 0, - .num_resources = ARRAY_SIZE(overo_smsc911x_resources), - .resource = overo_smsc911x_resources, - .dev = { - .platform_data = &overo_smsc911x_config, - }, + .cs = OVERO_SMSC911X_CS, + .gpio_irq = OVERO_SMSC911X_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT, }; -static struct platform_device overo_smsc911x2_device = { - .name = "smsc911x", +static struct omap_smsc911x_platform_data smsc911x2_cfg = { .id = 1, - .num_resources = ARRAY_SIZE(overo_smsc911x2_resources), - .resource = overo_smsc911x2_resources, - .dev = { - .platform_data = &overo_smsc911x_config, - }, + .cs = OVERO_SMSC911X2_CS, + .gpio_irq = OVERO_SMSC911X2_GPIO, + .gpio_reset = -EINVAL, + .flags = SMSC911X_USE_32BIT, }; -static struct platform_device *smsc911x_devices[] = { - &overo_smsc911x_device, - &overo_smsc911x2_device, -}; - -static inline void __init overo_init_smsc911x(void) +static void __init overo_init_smsc911x(void) { - unsigned long cs_mem_base, cs_mem_base2; - - /* set up first smsc911x chip */ - - if (gpmc_cs_request(OVERO_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) { - printk(KERN_ERR "Failed request for GPMC mem for smsc911x\n"); - return; - } - - overo_smsc911x_resources[0].start = cs_mem_base + 0x0; - overo_smsc911x_resources[0].end = cs_mem_base + 0xff; - - if ((gpio_request(OVERO_SMSC911X_GPIO, "SMSC911X IRQ") == 0) && - (gpio_direction_input(OVERO_SMSC911X_GPIO) == 0)) { - gpio_export(OVERO_SMSC911X_GPIO, 0); - } else { - printk(KERN_ERR "could not obtain gpio for SMSC911X IRQ\n"); - return; - } - - overo_smsc911x_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X_GPIO); - overo_smsc911x_resources[1].end = 0; - - /* set up second smsc911x chip */ - - if (gpmc_cs_request(OVERO_SMSC911X2_CS, SZ_16M, &cs_mem_base2) < 0) { - printk(KERN_ERR "Failed request for GPMC mem for smsc911x2\n"); - return; - } - - overo_smsc911x2_resources[0].start = cs_mem_base2 + 0x0; - overo_smsc911x2_resources[0].end = cs_mem_base2 + 0xff; - - if ((gpio_request(OVERO_SMSC911X2_GPIO, "SMSC911X2 IRQ") == 0) && - (gpio_direction_input(OVERO_SMSC911X2_GPIO) == 0)) { - gpio_export(OVERO_SMSC911X2_GPIO, 0); - } else { - printk(KERN_ERR "could not obtain gpio for SMSC911X2 IRQ\n"); - return; - } - - overo_smsc911x2_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X2_GPIO); - overo_smsc911x2_resources[1].end = 0; - - platform_add_devices(smsc911x_devices, ARRAY_SIZE(smsc911x_devices)); + gpmc_smsc911x_init(&smsc911x_cfg); + gpmc_smsc911x_init(&smsc911x2_cfg); } #else @@ -259,21 +151,20 @@ static int dvi_enabled; #define OVERO_GPIO_LCD_EN 144 #define OVERO_GPIO_LCD_BL 145 +static struct gpio overo_dss_gpios[] __initdata = { + { OVERO_GPIO_LCD_EN, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_EN" }, + { OVERO_GPIO_LCD_BL, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_BL" }, +}; + static void __init overo_display_init(void) { - if ((gpio_request(OVERO_GPIO_LCD_EN, "OVERO_GPIO_LCD_EN") == 0) && - (gpio_direction_output(OVERO_GPIO_LCD_EN, 1) == 0)) - gpio_export(OVERO_GPIO_LCD_EN, 0); - else - printk(KERN_ERR "could not obtain gpio for " - "OVERO_GPIO_LCD_EN\n"); + if (gpio_request_array(overo_dss_gpios, ARRAY_SIZE(overo_dss_gpios))) { + printk(KERN_ERR "could not obtain DSS control GPIOs\n"); + return; + } - if ((gpio_request(OVERO_GPIO_LCD_BL, "OVERO_GPIO_LCD_BL") == 0) && - (gpio_direction_output(OVERO_GPIO_LCD_BL, 1) == 0)) - gpio_export(OVERO_GPIO_LCD_BL, 0); - else - printk(KERN_ERR "could not obtain gpio for " - "OVERO_GPIO_LCD_BL\n"); + gpio_export(OVERO_GPIO_LCD_EN, 0); + gpio_export(OVERO_GPIO_LCD_BL, 0); } static int overo_panel_enable_dvi(struct omap_dss_device *dssdev) @@ -412,45 +303,6 @@ static struct mtd_partition overo_nand_partitions[] = { }, }; -static struct omap_nand_platform_data overo_nand_data = { - .parts = overo_nand_partitions, - .nr_parts = ARRAY_SIZE(overo_nand_partitions), - .dma_channel = -1, /* disable DMA in OMAP NAND driver */ -}; - -static void __init overo_flash_init(void) -{ - u8 cs = 0; - u8 nandcs = GPMC_CS_NUM + 1; - - /* find out the chip-select on which NAND exists */ - while (cs < GPMC_CS_NUM) { - u32 ret = 0; - ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); - - if ((ret & 0xC00) == 0x800) { - printk(KERN_INFO "Found NAND on CS%d\n", cs); - if (nandcs > GPMC_CS_NUM) - nandcs = cs; - } - cs++; - } - - if (nandcs > GPMC_CS_NUM) { - printk(KERN_INFO "NAND: Unable to find configuration " - "in GPMC\n "); - return; - } - - if (nandcs < GPMC_CS_NUM) { - overo_nand_data.cs = nandcs; - - printk(KERN_INFO "Registering NAND on CS%d\n", nandcs); - if (gpmc_nand_init(&overo_nand_data) < 0) - printk(KERN_ERR "Unable to register NAND device\n"); - } -} - static struct omap2_hsmmc_info mmc[] = { { .mmc = 1, @@ -648,37 +500,15 @@ static struct twl4030_platform_data overo_twldata = { .vpll2 = &overo_vpll2, }; -static struct i2c_board_info __initdata overo_i2c_boardinfo[] = { - { - I2C_BOARD_INFO("tps65950", 0x48), - .flags = I2C_CLIENT_WAKE, - .irq = INT_34XX_SYS_NIRQ, - .platform_data = &overo_twldata, - }, -}; - static int __init overo_i2c_init(void) { - omap_register_i2c_bus(1, 2600, overo_i2c_boardinfo, - ARRAY_SIZE(overo_i2c_boardinfo)); + omap3_pmic_init("tps65950", &overo_twldata); /* i2c2 pins are used for gpio */ omap_register_i2c_bus(3, 400, NULL, 0); return 0; } static struct spi_board_info overo_spi_board_info[] __initdata = { -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \ - defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - { - .modalias = "ads7846", - .bus_num = 1, - .chip_select = 0, - .max_speed_hz = 1500000, - .controller_data = &ads7846_mcspi_config, - .irq = OMAP_GPIO_IRQ(OVERO_GPIO_PENDOWN), - .platform_data = &ads7846_config, - }, -#endif #if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \ defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE) { @@ -722,20 +552,22 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif -static struct omap_musb_board_data musb_board_data = { - .interface_type = MUSB_INTERFACE_ULPI, - .mode = MUSB_OTG, - .power = 100, +static struct gpio overo_bt_gpios[] __initdata = { + { OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" }, + { OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" }, }; static void __init overo_init(void) { + int ret; + omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); overo_i2c_init(); omap_display_init(&overo_dss_data); omap_serial_init(); - overo_flash_init(); - usb_musb_init(&musb_board_data); + omap_nand_flash_init(0, overo_nand_partitions, + ARRAY_SIZE(overo_nand_partitions)); + usb_musb_init(NULL); usbhs_init(&usbhs_bdata); overo_spi_init(); overo_ads7846_init(); @@ -748,9 +580,9 @@ static void __init overo_init(void) omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT); omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT); - if ((gpio_request(OVERO_GPIO_W2W_NRESET, - "OVERO_GPIO_W2W_NRESET") == 0) && - (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) { + ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH, + "OVERO_GPIO_W2W_NRESET"); + if (ret == 0) { gpio_export(OVERO_GPIO_W2W_NRESET, 0); gpio_set_value(OVERO_GPIO_W2W_NRESET, 0); udelay(10); @@ -760,25 +592,20 @@ static void __init overo_init(void) "OVERO_GPIO_W2W_NRESET\n"); } - if ((gpio_request(OVERO_GPIO_BT_XGATE, "OVERO_GPIO_BT_XGATE") == 0) && - (gpio_direction_output(OVERO_GPIO_BT_XGATE, 0) == 0)) + ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios)); + if (ret) { + pr_err("%s: could not obtain BT gpios\n", __func__); + } else { gpio_export(OVERO_GPIO_BT_XGATE, 0); - else - printk(KERN_ERR "could not obtain gpio for OVERO_GPIO_BT_XGATE\n"); - - if ((gpio_request(OVERO_GPIO_BT_NRESET, "OVERO_GPIO_BT_NRESET") == 0) && - (gpio_direction_output(OVERO_GPIO_BT_NRESET, 1) == 0)) { gpio_export(OVERO_GPIO_BT_NRESET, 0); gpio_set_value(OVERO_GPIO_BT_NRESET, 0); mdelay(6); gpio_set_value(OVERO_GPIO_BT_NRESET, 1); - } else { - printk(KERN_ERR "could not obtain gpio for " - "OVERO_GPIO_BT_NRESET\n"); } - if ((gpio_request(OVERO_GPIO_USBH_CPEN, "OVERO_GPIO_USBH_CPEN") == 0) && - (gpio_direction_output(OVERO_GPIO_USBH_CPEN, 1) == 0)) + ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH, + "OVERO_GPIO_USBH_CPEN"); + if (ret == 0) gpio_export(OVERO_GPIO_USBH_CPEN, 0); else printk(KERN_ERR "could not obtain gpio for " |