1 files changed, 367 insertions, 0 deletions
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
new file mode 100644
index 00000000000..031d116fbf1
--- /dev/null
+++ b/arch/arm/mach-omap2/vc.c
@@ -0,0 +1,367 @@
+/*
+ * OMAP Voltage Controller (VC) interface
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+
+#include <plat/cpu.h>
+
+#include "voltage.h"
+#include "vc.h"
+#include "prm-regbits-34xx.h"
+#include "prm-regbits-44xx.h"
+#include "prm44xx.h"
+
+/**
+ * struct omap_vc_channel_cfg - describe the cfg_channel bitfield
+ * @sa: bit for slave address
+ * @rav: bit for voltage configuration register
+ * @rac: bit for command configuration register
+ * @racen: enable bit for RAC
+ * @cmd: bit for command value set selection
+ *
+ * Channel configuration bits, common for OMAP3+
+ * OMAP3 register: PRM_VC_CH_CONF
+ * OMAP4 register: PRM_VC_CFG_CHANNEL
+ * OMAP5 register: PRM_VC_SMPS_<voltdm>_CONFIG
+ */
+struct omap_vc_channel_cfg {
+	u8 sa;
+	u8 rav;
+	u8 rac;
+	u8 racen;
+	u8 cmd;
+};
+
+static struct omap_vc_channel_cfg vc_default_channel_cfg = {
+	.sa    = BIT(0),
+	.rav   = BIT(1),
+	.rac   = BIT(2),
+	.racen = BIT(3),
+	.cmd   = BIT(4),
+};
+
+/*
+ * On OMAP3+, all VC channels have the above default bitfield
+ * configuration, except the OMAP4 MPU channel.  This appears
+ * to be a freak accident as every other VC channel has the
+ * default configuration, thus creating a mutant channel config.
+ */
+static struct omap_vc_channel_cfg vc_mutant_channel_cfg = {
+	.sa    = BIT(0),
+	.rav   = BIT(2),
+	.rac   = BIT(3),
+	.racen = BIT(4),
+	.cmd   = BIT(1),
+};
+
+static struct omap_vc_channel_cfg *vc_cfg_bits;
+#define CFG_CHANNEL_MASK 0x1f
+
+/**
+ * omap_vc_config_channel - configure VC channel to PMIC mappings
+ * @voltdm: pointer to voltagdomain defining the desired VC channel
+ *
+ * Configures the VC channel to PMIC mappings for the following
+ * PMIC settings
+ * - i2c slave address (SA)
+ * - voltage configuration address (RAV)
+ * - command configuration address (RAC) and enable bit (RACEN)
+ * - command values for ON, ONLP, RET and OFF (CMD)
+ *
+ * This function currently only allows flexible configuration of the
+ * non-default channel.  Starting with OMAP4, there are more than 2
+ * channels, with one defined as the default (on OMAP4, it's MPU.)
+ * Only the non-default channel can be configured.
+ */
+static int omap_vc_config_channel(struct voltagedomain *voltdm)
+{
+	struct omap_vc_channel *vc = voltdm->vc;
+
+	/*
+	 * For default channel, the only configurable bit is RACEN.
+	 * All others must stay at zero (see function comment above.)
+	 */
+	if (vc->flags & OMAP_VC_CHANNEL_DEFAULT)
+		vc->cfg_channel &= vc_cfg_bits->racen;
+
+	voltdm->rmw(CFG_CHANNEL_MASK << vc->cfg_channel_sa_shift,
+		    vc->cfg_channel << vc->cfg_channel_sa_shift,
+		    vc->cfg_channel_reg);
+
+	return 0;
+}
+
+/* Voltage scale and accessory APIs */
+int omap_vc_pre_scale(struct voltagedomain *voltdm,
+		      unsigned long target_volt,
+		      u8 *target_vsel, u8 *current_vsel)
+{
+	struct omap_vc_channel *vc = voltdm->vc;
+	u32 vc_cmdval;
+
+	/* Check if sufficient pmic info is available for this vdd */
+	if (!voltdm->pmic) {
+		pr_err("%s: Insufficient pmic info to scale the vdd_%s\n",
+			__func__, voltdm->name);
+		return -EINVAL;
+	}
+
+	if (!voltdm->pmic->uv_to_vsel) {
+		pr_err("%s: PMIC function to convert voltage in uV to"
+			"vsel not registered. Hence unable to scale voltage"
+			"for vdd_%s\n", __func__, voltdm->name);
+		return -ENODATA;
+	}
+
+	if (!voltdm->read || !voltdm->write) {
+		pr_err("%s: No read/write API for accessing vdd_%s regs\n",
+			__func__, voltdm->name);
+		return -EINVAL;
+	}
+
+	*target_vsel = voltdm->pmic->uv_to_vsel(target_volt);
+	*current_vsel = voltdm->pmic->uv_to_vsel(voltdm->nominal_volt);
+
+	/* Setting the ON voltage to the new target voltage */
+	vc_cmdval = voltdm->read(vc->cmdval_reg);
+	vc_cmdval &= ~vc->common->cmd_on_mask;
+	vc_cmdval |= (*target_vsel << vc->common->cmd_on_shift);
+	voltdm->write(vc_cmdval, vc->cmdval_reg);
+
+	omap_vp_update_errorgain(voltdm, target_volt);
+
+	return 0;
+}
+
+void omap_vc_post_scale(struct voltagedomain *voltdm,
+			unsigned long target_volt,
+			u8 target_vsel, u8 current_vsel)
+{
+	u32 smps_steps = 0, smps_delay = 0;
+
+	smps_steps = abs(target_vsel - current_vsel);
+	/* SMPS slew rate / step size. 2us added as buffer. */
+	smps_delay = ((smps_steps * voltdm->pmic->step_size) /
+			voltdm->pmic->slew_rate) + 2;
+	udelay(smps_delay);
+}
+
+/* vc_bypass_scale - VC bypass method of voltage scaling */
+int omap_vc_bypass_scale(struct voltagedomain *voltdm,
+			 unsigned long target_volt)
+{
+	struct omap_vc_channel *vc = voltdm->vc;
+	u32 loop_cnt = 0, retries_cnt = 0;
+	u32 vc_valid, vc_bypass_val_reg, vc_bypass_value;
+	u8 target_vsel, current_vsel;
+	int ret;
+
+	ret = omap_vc_pre_scale(voltdm, target_volt, &target_vsel, &current_vsel);
+	if (ret)
+		return ret;
+
+	vc_valid = vc->common->valid;
+	vc_bypass_val_reg = vc->common->bypass_val_reg;
+	vc_bypass_value = (target_vsel << vc->common->data_shift) |
+		(vc->volt_reg_addr << vc->common->regaddr_shift) |
+		(vc->i2c_slave_addr << vc->common->slaveaddr_shift);
+
+	voltdm->write(vc_bypass_value, vc_bypass_val_reg);
+	voltdm->write(vc_bypass_value | vc_valid, vc_bypass_val_reg);
+
+	vc_bypass_value = voltdm->read(vc_bypass_val_reg);
+	/*
+	 * Loop till the bypass command is acknowledged from the SMPS.
+	 * NOTE: This is legacy code. The loop count and retry count needs
+	 * to be revisited.
+	 */
+	while (!(vc_bypass_value & vc_valid)) {
+		loop_cnt++;
+
+		if (retries_cnt > 10) {
+			pr_warning("%s: Retry count exceeded\n", __func__);
+			return -ETIMEDOUT;
+		}
+
+		if (loop_cnt > 50) {
+			retries_cnt++;
+			loop_cnt = 0;
+			udelay(10);
+		}
+		vc_bypass_value = voltdm->read(vc_bypass_val_reg);
+	}
+
+	omap_vc_post_scale(voltdm, target_volt, target_vsel, current_vsel);
+	return 0;
+}
+
+static void __init omap3_vfsm_init(struct voltagedomain *voltdm)
+{
+	/*
+	 * Voltage Manager FSM parameters init
+	 * XXX This data should be passed in from the board file
+	 */
+	voltdm->write(OMAP3_CLKSETUP, OMAP3_PRM_CLKSETUP_OFFSET);
+	voltdm->write(OMAP3_VOLTOFFSET, OMAP3_PRM_VOLTOFFSET_OFFSET);
+	voltdm->write(OMAP3_VOLTSETUP2, OMAP3_PRM_VOLTSETUP2_OFFSET);
+}
+
+static void __init omap3_vc_init_channel(struct voltagedomain *voltdm)
+{
+	static bool is_initialized;
+
+	if (is_initialized)
+		return;
+
+	omap3_vfsm_init(voltdm);
+
+	is_initialized = true;
+}
+
+
+/* OMAP4 specific voltage init functions */
+static void __init omap4_vc_init_channel(struct voltagedomain *voltdm)
+{
+	static bool is_initialized;
+	u32 vc_val;
+
+	if (is_initialized)
+		return;
+
+	/* XXX These are magic numbers and do not belong! */
+	vc_val = (0x60 << OMAP4430_SCLL_SHIFT | 0x26 << OMAP4430_SCLH_SHIFT);
+	voltdm->write(vc_val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET);
+
+	is_initialized = true;
+}
+
+/**
+ * omap_vc_i2c_init - initialize I2C interface to PMIC
+ * @voltdm: voltage domain containing VC data
+ *
+ * Use PMIC supplied seetings for I2C high-speed mode and
+ * master code (if set) and program the VC I2C configuration
+ * register.
+ *
+ * The VC I2C configuration is common to all VC channels,
+ * so this function only configures I2C for the first VC
+ * channel registers.  All other VC channels will use the
+ * same configuration.
+ */
+static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
+{
+	struct omap_vc_channel *vc = voltdm->vc;
+	static bool initialized;
+	static bool i2c_high_speed;
+	u8 mcode;
+
+	if (initialized) {
+		if (voltdm->pmic->i2c_high_speed != i2c_high_speed)
+			pr_warn("%s: I2C config for all channels must match.",
+				__func__);
+		return;
+	}
+
+	i2c_high_speed = voltdm->pmic->i2c_high_speed;
+	if (i2c_high_speed)
+		voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
+			    vc->common->i2c_cfg_hsen_mask,
+			    vc->common->i2c_cfg_reg);
+
+	mcode = voltdm->pmic->i2c_mcode;
+	if (mcode)
+		voltdm->rmw(vc->common->i2c_mcode_mask,
+			    mcode << __ffs(vc->common->i2c_mcode_mask),
+			    vc->common->i2c_cfg_reg);
+
+	initialized = true;
+}
+
+void __init omap_vc_init_channel(struct voltagedomain *voltdm)
+{
+	struct omap_vc_channel *vc = voltdm->vc;
+	u8 on_vsel, onlp_vsel, ret_vsel, off_vsel;
+	u32 val;
+
+	if (!voltdm->pmic || !voltdm->pmic->uv_to_vsel) {
+		pr_err("%s: PMIC info requried to configure vc for"
+			"vdd_%s not populated.Hence cannot initialize vc\n",
+			__func__, voltdm->name);
+		return;
+	}
+
+	if (!voltdm->read || !voltdm->write) {
+		pr_err("%s: No read/write API for accessing vdd_%s regs\n",
+			__func__, voltdm->name);
+		return;
+	}
+
+	vc->cfg_channel = 0;
+	if (vc->flags & OMAP_VC_CHANNEL_CFG_MUTANT)
+		vc_cfg_bits = &vc_mutant_channel_cfg;
+	else
+		vc_cfg_bits = &vc_default_channel_cfg;
+
+	/* get PMIC/board specific settings */
+	vc->i2c_slave_addr = voltdm->pmic->i2c_slave_addr;
+	vc->volt_reg_addr = voltdm->pmic->volt_reg_addr;
+	vc->cmd_reg_addr = voltdm->pmic->cmd_reg_addr;
+	vc->setup_time = voltdm->pmic->volt_setup_time;
+
+	/* Configure the i2c slave address for this VC */
+	voltdm->rmw(vc->smps_sa_mask,
+		    vc->i2c_slave_addr << __ffs(vc->smps_sa_mask),
+		    vc->smps_sa_reg);
+	vc->cfg_channel |= vc_cfg_bits->sa;
+
+	/*
+	 * Configure the PMIC register addresses.
+	 */
+	voltdm->rmw(vc->smps_volra_mask,
+		    vc->volt_reg_addr << __ffs(vc->smps_volra_mask),
+		    vc->smps_volra_reg);
+	vc->cfg_channel |= vc_cfg_bits->rav;
+
+	if (vc->cmd_reg_addr) {
+		voltdm->rmw(vc->smps_cmdra_mask,
+			    vc->cmd_reg_addr << __ffs(vc->smps_cmdra_mask),
+			    vc->smps_cmdra_reg);
+		vc->cfg_channel |= vc_cfg_bits->rac | vc_cfg_bits->racen;
+	}
+
+	/* Set up the on, inactive, retention and off voltage */
+	on_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->on_volt);
+	onlp_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->onlp_volt);
+	ret_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->ret_volt);
+	off_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->off_volt);
+	val = ((on_vsel << vc->common->cmd_on_shift) |
+	       (onlp_vsel << vc->common->cmd_onlp_shift) |
+	       (ret_vsel << vc->common->cmd_ret_shift) |
+	       (off_vsel << vc->common->cmd_off_shift));
+	voltdm->write(val, vc->cmdval_reg);
+	vc->cfg_channel |= vc_cfg_bits->cmd;
+
+	/* Channel configuration */
+	omap_vc_config_channel(voltdm);
+
+	/* Configure the setup times */
+	voltdm->rmw(voltdm->vfsm->voltsetup_mask,
+		    vc->setup_time << __ffs(voltdm->vfsm->voltsetup_mask),
+		    voltdm->vfsm->voltsetup_reg);
+
+	omap_vc_i2c_init(voltdm);
+
+	if (cpu_is_omap34xx())
+		omap3_vc_init_channel(voltdm);
+	else if (cpu_is_omap44xx())
+		omap4_vc_init_channel(voltdm);
+}
+