diff options
Diffstat (limited to 'arch/arm/mach-omap2')
52 files changed, 710 insertions, 344 deletions
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 497e9dc2795..e1293aa513d 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -14,7 +14,6 @@ config ARCH_OMAP2PLUS_TYPICAL select SERIAL_OMAP_CONSOLE select I2C select I2C_OMAP - select MFD_SUPPORT select MENELAUS if ARCH_OMAP2 select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4 select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4 @@ -335,6 +334,7 @@ config MACH_OMAP4_PANDA config OMAP3_EMU bool "OMAP3 debugging peripherals" depends on ARCH_OMAP3 + select ARM_AMBA select OC_ETM help Say Y here to enable debugging hardware of omap3 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 69ab1c06913..b009f17dee5 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -4,7 +4,7 @@ # Common support obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \ - common.o gpio.o dma.o wd_timer.o + common.o gpio.o dma.o wd_timer.o display.o omap-2-3-common = irq.o sdrc.o hwmod-common = omap_hwmod.o \ @@ -264,7 +264,4 @@ smsc911x-$(CONFIG_SMSC911X) := gpmc-smsc911x.o obj-y += $(smsc911x-m) $(smsc911x-y) obj-$(CONFIG_ARCH_OMAP4) += hwspinlock.o -disp-$(CONFIG_OMAP2_DSS) := display.o -obj-y += $(disp-m) $(disp-y) - obj-y += common-board-devices.o twl-common.o diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index 42918940c53..90154e411da 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -226,7 +226,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev, { int ret; - omap_mux_init_gpio(29, OMAP_PIN_INPUT); /* gpio + 0 is "mmc0_cd" (input/IRQ) */ mmc[0].gpio_cd = gpio + 0; omap2_hsmmc_init(mmc); diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 0cc9094e5ee..fb55fa3dad5 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -28,6 +28,7 @@ * XXX: Still needed to boot until the i2c & twl driver is adapted to * device-tree */ +#ifdef CONFIG_ARCH_OMAP4 static struct twl4030_platform_data sdp4430_twldata = { .irq_base = TWL6030_IRQ_BASE, .irq_end = TWL6030_IRQ_END, @@ -37,7 +38,9 @@ static void __init omap4_i2c_init(void) { omap4_pmic_init("twl6030", &sdp4430_twldata); } +#endif +#ifdef CONFIG_ARCH_OMAP3 static struct twl4030_platform_data beagle_twldata = { .irq_base = TWL4030_IRQ_BASE, .irq_end = TWL4030_IRQ_END, @@ -47,6 +50,7 @@ static void __init omap3_i2c_init(void) { omap3_pmic_init("twl4030", &beagle_twldata); } +#endif static struct of_device_id omap_dt_match_table[] __initdata = { { .compatible = "simple-bus", }, @@ -72,17 +76,21 @@ static void __init omap_generic_init(void) of_platform_populate(NULL, omap_dt_match_table, NULL, NULL); } +#ifdef CONFIG_ARCH_OMAP4 static void __init omap4_init(void) { omap4_i2c_init(); omap_generic_init(); } +#endif +#ifdef CONFIG_ARCH_OMAP3 static void __init omap3_init(void) { omap3_i2c_init(); omap_generic_init(); } +#endif #if defined(CONFIG_SOC_OMAP2420) static const char *omap242x_boards_compat[] __initdata = { diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index c12666ee701..8b351d92a1c 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -25,6 +25,7 @@ #include <linux/err.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/input/matrix_keypad.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -34,7 +35,6 @@ #include <plat/usb.h> #include <plat/board.h> #include <plat/common.h> -#include <plat/keypad.h> #include <plat/menelaus.h> #include <plat/dma.h> #include <plat/gpmc.h> @@ -50,10 +50,8 @@ #define H4_ETHR_GPIO_IRQ 92 -static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 }; -static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 }; - -static const unsigned int h4_keymap[] = { +#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE) +static const uint32_t board_matrix_keys[] = { KEY(0, 0, KEY_LEFT), KEY(1, 0, KEY_RIGHT), KEY(2, 0, KEY_A), @@ -86,6 +84,71 @@ static const unsigned int h4_keymap[] = { KEY(4, 5, KEY_ENTER), }; +static const struct matrix_keymap_data board_keymap_data = { + .keymap = board_matrix_keys, + .keymap_size = ARRAY_SIZE(board_matrix_keys), +}; + +static unsigned int board_keypad_row_gpios[] = { + 88, 89, 124, 11, 6, 96 +}; + +static unsigned int board_keypad_col_gpios[] = { + 90, 91, 100, 36, 12, 97, 98 +}; + +static struct matrix_keypad_platform_data board_keypad_platform_data = { + .keymap_data = &board_keymap_data, + .row_gpios = board_keypad_row_gpios, + .num_row_gpios = ARRAY_SIZE(board_keypad_row_gpios), + .col_gpios = board_keypad_col_gpios, + .num_col_gpios = ARRAY_SIZE(board_keypad_col_gpios), + .active_low = 1, + + .debounce_ms = 20, + .col_scan_delay_us = 5, +}; + +static struct platform_device board_keyboard = { + .name = "matrix-keypad", + .id = -1, + .dev = { + .platform_data = &board_keypad_platform_data, + }, +}; +static void __init board_mkp_init(void) +{ + omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP); + if (omap_has_menelaus()) { + omap_mux_init_signal("sdrc_a14.gpio0", + OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("vlynq_rx0.gpio_15", 0); + omap_mux_init_signal("gpio_98", 0); + board_keypad_row_gpios[5] = 0; + board_keypad_col_gpios[2] = 15; + board_keypad_col_gpios[6] = 18; + } else { + omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("gpio_100", 0); + omap_mux_init_signal("gpio_98", 0); + } + omap_mux_init_signal("gpio_90", 0); + omap_mux_init_signal("gpio_91", 0); + omap_mux_init_signal("gpio_36", 0); + omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0); + omap_mux_init_signal("gpio_97", 0); + + platform_device_register(&board_keyboard); +} +#else +static inline void board_mkp_init(void) +{ +} +#endif + static struct mtd_partition h4_partitions[] = { /* bootloader (U-Boot, etc) in first sector */ { @@ -137,31 +200,8 @@ static struct platform_device h4_flash_device = { .resource = &h4_flash_resource, }; -static const struct matrix_keymap_data h4_keymap_data = { - .keymap = h4_keymap, - .keymap_size = ARRAY_SIZE(h4_keymap), -}; - -static struct omap_kp_platform_data h4_kp_data = { - .rows = 6, - .cols = 7, - .keymap_data = &h4_keymap_data, - .rep = true, - .row_gpios = row_gpios, - .col_gpios = col_gpios, -}; - -static struct platform_device h4_kp_device = { - .name = "omap-keypad", - .id = -1, - .dev = { - .platform_data = &h4_kp_data, - }, -}; - static struct platform_device *h4_devices[] __initdata = { &h4_flash_device, - &h4_kp_device, }; static struct panel_generic_dpi_data h4_panel_data = { @@ -336,31 +376,7 @@ static void __init omap_h4_init(void) * if not needed. */ -#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE) - omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP); - omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP); - omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP); - omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP); - if (omap_has_menelaus()) { - omap_mux_init_signal("sdrc_a14.gpio0", - OMAP_PULL_ENA | OMAP_PULL_UP); - omap_mux_init_signal("vlynq_rx0.gpio_15", 0); - omap_mux_init_signal("gpio_98", 0); - row_gpios[5] = 0; - col_gpios[2] = 15; - col_gpios[6] = 18; - } else { - omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP); - omap_mux_init_signal("gpio_100", 0); - omap_mux_init_signal("gpio_98", 0); - } - omap_mux_init_signal("gpio_90", 0); - omap_mux_init_signal("gpio_91", 0); - omap_mux_init_signal("gpio_36", 0); - omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0); - omap_mux_init_signal("gpio_97", 0); -#endif - + board_mkp_init(); i2c_register_board_info(1, h4_i2c_board_info, ARRAY_SIZE(h4_i2c_board_info)); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 70261bcda3f..4a71cb7e42d 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -378,7 +378,8 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = { static int __init omap3_beagle_i2c_init(void) { omap3_pmic_get_config(&beagle_twldata, - TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO, + TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC | + TWL_COMMON_PDATA_AUDIO, TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2); beagle_twldata.vpll2->constraints.name = "VDVI"; @@ -444,9 +445,15 @@ static struct platform_device keys_gpio = { }, }; +static struct platform_device madc_hwmon = { + .name = "twl4030_madc_hwmon", + .id = -1, +}; + static struct platform_device *omap3_beagle_devices[] __initdata = { &leds_gpio, &keys_gpio, + &madc_hwmon, }; static const struct usbhs_omap_board_data usbhs_bdata __initconst = { diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 2d24e287e8c..ec00b2ec702 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -34,6 +34,7 @@ #include <linux/regulator/fixed.h> #include <linux/regulator/machine.h> #include <linux/mmc/host.h> +#include <linux/export.h> #include <mach/hardware.h> #include <asm/mach-types.h> diff --git a/arch/arm/mach-omap2/clkt_dpll.c b/arch/arm/mach-omap2/clkt_dpll.c index bcffee001bf..e069a9be93d 100644 --- a/arch/arm/mach-omap2/clkt_dpll.c +++ b/arch/arm/mach-omap2/clkt_dpll.c @@ -46,10 +46,19 @@ (DPLL_SCALE_FACTOR / DPLL_SCALE_BASE)) /* DPLL valid Fint frequency band limits - from 34xx TRM Section 4.7.6.2 */ -#define DPLL_FINT_BAND1_MIN 750000 -#define DPLL_FINT_BAND1_MAX 2100000 -#define DPLL_FINT_BAND2_MIN 7500000 -#define DPLL_FINT_BAND2_MAX 21000000 +#define OMAP3430_DPLL_FINT_BAND1_MIN 750000 +#define OMAP3430_DPLL_FINT_BAND1_MAX 2100000 +#define OMAP3430_DPLL_FINT_BAND2_MIN 7500000 +#define OMAP3430_DPLL_FINT_BAND2_MAX 21000000 + +/* + * DPLL valid Fint frequency range for OMAP36xx and OMAP4xxx. + * From device data manual section 4.3 "DPLL and DLL Specifications". + */ +#define OMAP3PLUS_DPLL_FINT_JTYPE_MIN 500000 +#define OMAP3PLUS_DPLL_FINT_JTYPE_MAX 2500000 +#define OMAP3PLUS_DPLL_FINT_MIN 32000 +#define OMAP3PLUS_DPLL_FINT_MAX 52000000 /* _dpll_test_fint() return codes */ #define DPLL_FINT_UNDERFLOW -1 @@ -71,33 +80,43 @@ static int _dpll_test_fint(struct clk *clk, u8 n) { struct dpll_data *dd; - long fint; + long fint, fint_min, fint_max; int ret = 0; dd = clk->dpll_data; /* DPLL divider must result in a valid jitter correction val */ fint = clk->parent->rate / n; - if (fint < DPLL_FINT_BAND1_MIN) { + if (cpu_is_omap24xx()) { + /* Should not be called for OMAP2, so warn if it is called */ + WARN(1, "No fint limits available for OMAP2!\n"); + return DPLL_FINT_INVALID; + } else if (cpu_is_omap3430()) { + fint_min = OMAP3430_DPLL_FINT_BAND1_MIN; + fint_max = OMAP3430_DPLL_FINT_BAND2_MAX; + } else if (dd->flags & DPLL_J_TYPE) { + fint_min = OMAP3PLUS_DPLL_FINT_JTYPE_MIN; + fint_max = OMAP3PLUS_DPLL_FINT_JTYPE_MAX; + } else { + fint_min = OMAP3PLUS_DPLL_FINT_MIN; + fint_max = OMAP3PLUS_DPLL_FINT_MAX; + } + + if (fint < fint_min) { pr_debug("rejecting n=%d due to Fint failure, " "lowering max_divider\n", n); dd->max_divider = n; ret = DPLL_FINT_UNDERFLOW; - - } else if (fint > DPLL_FINT_BAND1_MAX && - fint < DPLL_FINT_BAND2_MIN) { - - pr_debug("rejecting n=%d due to Fint failure\n", n); - ret = DPLL_FINT_INVALID; - - } else if (fint > DPLL_FINT_BAND2_MAX) { - + } else if (fint > fint_max) { pr_debug("rejecting n=%d due to Fint failure, " "boosting min_divider\n", n); dd->min_divider = n; ret = DPLL_FINT_INVALID; - + } else if (cpu_is_omap3430() && fint > OMAP3430_DPLL_FINT_BAND1_MAX && + fint < OMAP3430_DPLL_FINT_BAND2_MIN) { + pr_debug("rejecting n=%d due to Fint failure\n", n); + ret = DPLL_FINT_INVALID; } return ret; diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 48ac568881b..2311bc21722 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -66,6 +66,8 @@ void omap3_noncore_dpll_disable(struct clk *clk); int omap4_dpllmx_gatectrl_read(struct clk *clk); void omap4_dpllmx_allow_gatectrl(struct clk *clk); void omap4_dpllmx_deny_gatectrl(struct clk *clk); +long omap4_dpll_regm4xen_round_rate(struct clk *clk, unsigned long target_rate); +unsigned long omap4_dpll_regm4xen_recalc(struct clk *clk); #ifdef CONFIG_OMAP_RESET_CLOCKS void omap2_clk_disable_unused(struct clk *clk); diff --git a/arch/arm/mach-omap2/clock2420_data.c b/arch/arm/mach-omap2/clock2420_data.c index 14a6277dd18..61ad3855f10 100644 --- a/arch/arm/mach-omap2/clock2420_data.c +++ b/arch/arm/mach-omap2/clock2420_data.c @@ -1898,18 +1898,6 @@ static struct omap_clk omap2420_clks[] = { CLK(NULL, "pka_ick", &pka_ick, CK_242X), CLK(NULL, "usb_fck", &usb_fck, CK_242X), CLK("musb-hdrc", "fck", &osc_ck, CK_242X), - CLK("omap_timer.1", "fck", &gpt1_fck, CK_242X), - CLK("omap_timer.2", "fck", &gpt2_fck, CK_242X), - CLK("omap_timer.3", "fck", &gpt3_fck, CK_242X), - CLK("omap_timer.4", "fck", &gpt4_fck, CK_242X), - CLK("omap_timer.5", "fck", &gpt5_fck, CK_242X), - CLK("omap_timer.6", "fck", &gpt6_fck, CK_242X), - CLK("omap_timer.7", "fck", &gpt7_fck, CK_242X), - CLK("omap_timer.8", "fck", &gpt8_fck, CK_242X), - CLK("omap_timer.9", "fck", &gpt9_fck, CK_242X), - CLK("omap_timer.10", "fck", &gpt10_fck, CK_242X), - CLK("omap_timer.11", "fck", &gpt11_fck, CK_242X), - CLK("omap_timer.12", "fck", &gpt12_fck, CK_242X), CLK("omap_timer.1", "32k_ck", &func_32k_ck, CK_243X), CLK("omap_timer.2", "32k_ck", &func_32k_ck, CK_243X), CLK("omap_timer.3", "32k_ck", &func_32k_ck, CK_243X), diff --git a/arch/arm/mach-omap2/clock2430_data.c b/arch/arm/mach-omap2/clock2430_data.c index ea6717cfa3c..0cc12879e7b 100644 --- a/arch/arm/mach-omap2/clock2430_data.c +++ b/arch/arm/mach-omap2/clock2430_data.c @@ -1998,18 +1998,6 @@ static struct omap_clk omap2430_clks[] = { CLK(NULL, "mdm_intc_ick", &mdm_intc_ick, CK_243X), CLK("omap_hsmmc.0", "mmchsdb_fck", &mmchsdb1_fck, CK_243X), CLK("omap_hsmmc.1", "mmchsdb_fck", &mmchsdb2_fck, CK_243X), - CLK("omap_timer.1", "fck", &gpt1_fck, CK_243X), - CLK("omap_timer.2", "fck", &gpt2_fck, CK_243X), - CLK("omap_timer.3", "fck", &gpt3_fck, CK_243X), - CLK("omap_timer.4", "fck", &gpt4_fck, CK_243X), - CLK("omap_timer.5", "fck", &gpt5_fck, CK_243X), - CLK("omap_timer.6", "fck", &gpt6_fck, CK_243X), - CLK("omap_timer.7", "fck", &gpt7_fck, CK_243X), - CLK("omap_timer.8", "fck", &gpt8_fck, CK_243X), - CLK("omap_timer.9", "fck", &gpt9_fck, CK_243X), - CLK("omap_timer.10", "fck", &gpt10_fck, CK_243X), - CLK("omap_timer.11", "fck", &gpt11_fck, CK_243X), - CLK("omap_timer.12", "fck", &gpt12_fck, CK_243X), CLK("omap_timer.1", "32k_ck", &func_32k_ck, CK_243X), CLK("omap_timer.2", "32k_ck", &func_32k_ck, CK_243X), CLK("omap_timer.3", "32k_ck", &func_32k_ck, CK_243X), diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c index 65dd363163b..5d0064a4fb5 100644 --- a/arch/arm/mach-omap2/clock3xxx_data.c +++ b/arch/arm/mach-omap2/clock3xxx_data.c @@ -3464,18 +3464,6 @@ static struct omap_clk omap3xxx_clks[] = { CLK("musb-am35x", "fck", &hsotgusb_fck_am35xx, CK_AM35XX), CLK(NULL, "hecc_ck", &hecc_ck, CK_AM35XX), CLK(NULL, "uart4_ick", &uart4_ick_am35xx, CK_AM35XX), - CLK("omap_timer.1", "fck", &gpt1_fck, CK_3XXX), - CLK("omap_timer.2", "fck", &gpt2_fck, CK_3XXX), - CLK("omap_timer.3", "fck", &gpt3_fck, CK_3XXX), - CLK("omap_timer.4", "fck", &gpt4_fck, CK_3XXX), - CLK("omap_timer.5", "fck", &gpt5_fck, CK_3XXX), - CLK("omap_timer.6", "fck", &gpt6_fck, CK_3XXX), - CLK("omap_timer.7", "fck", &gpt7_fck, CK_3XXX), - CLK("omap_timer.8", "fck", &gpt8_fck, CK_3XXX), - CLK("omap_timer.9", "fck", &gpt9_fck, CK_3XXX), - CLK("omap_timer.10", "fck", &gpt10_fck, CK_3XXX), - CLK("omap_timer.11", "fck", &gpt11_fck, CK_3XXX), - CLK("omap_timer.12", "fck", &gpt12_fck, CK_3XXX), CLK("omap_timer.1", "32k_ck", &omap_32k_fck, CK_3XXX), CLK("omap_timer.2", "32k_ck", &omap_32k_fck, CK_3XXX), CLK("omap_timer.3", "32k_ck", &omap_32k_fck, CK_3XXX), diff --git a/arch/arm/mach-omap2/clock44xx.h b/arch/arm/mach-omap2/clock44xx.h index 7ceb870e7ab..287a46f78d9 100644 --- a/arch/arm/mach-omap2/clock44xx.h +++ b/arch/arm/mach-omap2/clock44xx.h @@ -8,6 +8,13 @@ #ifndef __ARCH_ARM_MACH_OMAP2_CLOCK44XX_H #define __ARCH_ARM_MACH_OMAP2_CLOCK44XX_H +/* + * OMAP4430_REGM4XEN_MULT: If the CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN bit is + * set, then the DPLL's lock frequency is multiplied by 4 (OMAP4430 TRM + * vV Section 3.6.3.3.1 "DPLLs Output Clocks Parameters") + */ +#define OMAP4430_REGM4XEN_MULT 4 + int omap4xxx_clk_init(void); #endif diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index 946bf04a956..0798a802497 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -270,8 +270,8 @@ static struct clk dpll_abe_ck = { .dpll_data = &dpll_abe_dd, .init = &omap2_init_dpll_parent, .ops = &clkops_omap3_noncore_dpll_ops, - .recalc = &omap3_dpll_recalc, - .round_rate = &omap2_dpll_round_rate, + .recalc = &omap4_dpll_regm4xen_recalc, + .round_rate = &omap4_dpll_regm4xen_round_rate, .set_rate = &omap3_noncore_dpll_set_rate, }; @@ -1195,11 +1195,25 @@ static struct clk l4_wkup_clk_mux_ck = { .recalc = &omap2_clksel_recalc, }; +static const struct clksel_rate div2_2to1_rates[] = { + { .div = 1, .val = 1, .flags = RATE_IN_4430 }, + { .div = 2, .val = 0, .flags = RATE_IN_4430 }, + { .div = 0 }, +}; + +static const struct clksel ocp_abe_iclk_div[] = { + { .parent = &aess_fclk, .rates = div2_2to1_rates }, + { .parent = NULL }, +}; + static struct clk ocp_abe_iclk = { .name = "ocp_abe_iclk", .parent = &aess_fclk, + .clksel = ocp_abe_iclk_div, + .clksel_reg = OMAP4430_CM1_ABE_AESS_CLKCTRL, + .clksel_mask = OMAP4430_CLKSEL_AESS_FCLK_MASK, .ops = &clkops_null, - .recalc = &followparent_recalc, + .recalc = &omap2_clksel_recalc, }; static struct clk per_abe_24m_fclk = { @@ -1398,9 +1412,9 @@ static struct clk dss_dss_clk = { }; static const struct clksel_rate div3_8to32_rates[] = { - { .div = 8, .val = 0, .flags = RATE_IN_44XX }, - { .div = 16, .val = 1, .flags = RATE_IN_44XX }, - { .div = 32, .val = 2, .flags = RATE_IN_44XX }, + { .div = 8, .val = 0, .flags = RATE_IN_4460 }, + { .div = 16, .val = 1, .flags = RATE_IN_4460 }, + { .div = 32, .val = 2, .flags = RATE_IN_4460 }, { .div = 0 }, }; @@ -3363,17 +3377,6 @@ static struct omap_clk omap44xx_clks[] = { CLK("usbhs-omap.0", "usbhost_ick", &dummy_ck, CK_443X), CLK("usbhs-omap.0", "usbtll_fck", &dummy_ck, CK_443X), CLK("omap_wdt", "ick", &dummy_ck, CK_443X), - CLK("omap_timer.1", "fck", &timer1_fck, CK_443X), - CLK("omap_timer.2", "fck", &timer2_fck, CK_443X), - CLK("omap_timer.3", "fck", &timer3_fck, CK_443X), - CLK("omap_timer.4", "fck", &timer4_fck, CK_443X), - CLK("omap_timer.5", "fck", &timer5_fck, CK_443X), - CLK("omap_timer.6", "fck", &timer6_fck, CK_443X), - CLK("omap_timer.7", "fck", &timer7_fck, CK_443X), - CLK("omap_timer.8", "fck", &timer8_fck, CK_443X), - CLK("omap_timer.9", "fck", &timer9_fck, CK_443X), - CLK("omap_timer.10", "fck", &timer10_fck, CK_443X), - CLK("omap_timer.11", "fck", &timer11_fck, CK_443X), CLK("omap_timer.1", "32k_ck", &sys_32k_ck, CK_443X), CLK("omap_timer.2", "32k_ck", &sys_32k_ck, CK_443X), CLK("omap_timer.3", "32k_ck", &sys_32k_ck, CK_443X), @@ -3403,12 +3406,12 @@ int __init omap4xxx_clk_init(void) struct omap_clk *c; u32 cpu_clkflg; - if (cpu_is_omap44xx()) { + if (cpu_is_omap443x()) { cpu_mask = RATE_IN_4430; cpu_clkflg = CK_443X; } else if (cpu_is_omap446x()) { - cpu_mask = RATE_IN_4460; - cpu_clkflg = CK_446X; + cpu_mask = RATE_IN_4460 | RATE_IN_4430; + cpu_clkflg = CK_446X | CK_443X; } else { return 0; } diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c index 8480ee4344e..ad07689e156 100644 --- a/arch/arm/mach-omap2/clockdomain.c +++ b/arch/arm/mach-omap2/clockdomain.c @@ -17,6 +17,7 @@ #include <linux/device.h> #include <linux/list.h> #include <linux/errno.h> +#include <linux/string.h> #include <linux/delay.h> #include <linux/clk.h> #include <linux/limits.h> diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c index 4bf6e6e8b10..942bb4f19f9 100644 --- a/arch/arm/mach-omap2/cpuidle34xx.c +++ b/arch/arm/mach-omap2/cpuidle34xx.c @@ -24,6 +24,7 @@ #include <linux/sched.h> #include <linux/cpuidle.h> +#include <linux/export.h> #include <plat/prcm.h> #include <plat/irqs.h> @@ -88,17 +89,21 @@ static int _cpuidle_deny_idle(struct powerdomain *pwrdm, /** * omap3_enter_idle - Programs OMAP3 to enter the specified state * @dev: cpuidle device - * @state: The target state to be programmed + * @drv: cpuidle driver + * @index: the index of state to be entered * * Called from the CPUidle framework to program the device to the * specified target state selected by the governor. */ static int omap3_enter_idle(struct cpuidle_device *dev, - struct cpuidle_state *state) + struct cpuidle_driver *drv, + int index) { - struct omap3_idle_statedata *cx = cpuidle_get_statedata(state); + struct omap3_idle_statedata *cx = + cpuidle_get_statedata(&dev->states_usage[index]); struct timespec ts_preidle, ts_postidle, ts_idle; u32 mpu_state = cx->mpu_state, core_state = cx->core_state; + int idle_time; /* Used to keep track of the total time in idle */ getnstimeofday(&ts_preidle); @@ -113,7 +118,7 @@ static int omap3_enter_idle(struct cpuidle_device *dev, goto return_sleep_time; /* Deny idle for C1 */ - if (state == &dev->states[0]) { + if (index == 0) { pwrdm_for_each_clkdm(mpu_pd, _cpuidle_deny_idle); pwrdm_for_each_clkdm(core_pd, _cpuidle_deny_idle); } @@ -122,7 +127,7 @@ static int omap3_enter_idle(struct cpuidle_device *dev, omap_sram_idle(); /* Re-allow idle for C1 */ - if (state == &dev->states[0]) { + if (index == 0) { pwrdm_for_each_clkdm(mpu_pd, _cpuidle_allow_idle); pwrdm_for_each_clkdm(core_pd, _cpuidle_allow_idle); } @@ -134,28 +139,38 @@ return_sleep_time: local_irq_enable(); local_fiq_enable(); - return ts_idle.tv_nsec / NSEC_PER_USEC + ts_idle.tv_sec * USEC_PER_SEC; + idle_time = ts_idle.tv_nsec / NSEC_PER_USEC + ts_idle.tv_sec * \ + USEC_PER_SEC; + + /* Update cpuidle counters */ + dev->last_residency = idle_time; + + return index; } /** * next_valid_state - Find next valid C-state * @dev: cpuidle device - * @state: Currently selected C-state + * @drv: cpuidle driver + * @index: Index of currently selected c-state * - * If the current state is valid, it is returned back to the caller. - * Else, this function searches for a lower c-state which is still - * valid. + * If the state corresponding to index is valid, index is returned back + * to the caller. Else, this function searches for a lower c-state which is + * still valid (as defined in omap3_power_states[]) and returns its index. * * A state is valid if the 'valid' field is enabled and * if it satisfies the enable_off_mode condition. */ -static struct cpuidle_state *next_valid_state(struct cpuidle_device *dev, - struct cpuidle_state *curr) +static int next_valid_state(struct cpuidle_device *dev, + struct cpuidle_driver *drv, + int index) { - struct cpuidle_state *next = NULL; - struct omap3_idle_statedata *cx = cpuidle_get_statedata(curr); + struct cpuidle_state_usage *curr_usage = &dev->states_usage[index]; + struct cpuidle_state *curr = &drv->states[index]; + struct omap3_idle_statedata *cx = cpuidle_get_statedata(curr_usage); u32 mpu_deepest_state = PWRDM_POWER_RET; u32 core_deepest_state = PWRDM_POWER_RET; + int next_index = -1; if (enable_off_mode) { mpu_deepest_state = PWRDM_POWER_OFF; @@ -172,20 +187,20 @@ static struct cpuidle_state *next_valid_state(struct cpuidle_device *dev, if ((cx->valid) && (cx->mpu_state >= mpu_deepest_state) && (cx->core_state >= core_deepest_state)) { - return curr; + return index; } else { int idx = OMAP3_NUM_STATES - 1; /* Reach the current state starting at highest C-state */ for (; idx >= 0; idx--) { - if (&dev->states[idx] == curr) { - next = &dev->states[idx]; + if (&drv->states[idx] == curr) { + next_index = idx; break; } } /* Should never hit this condition */ - WARN_ON(next == NULL); + WARN_ON(next_index == -1); /* * Drop to next valid state. @@ -193,41 +208,44 @@ static struct cpuidle_state *next_valid_state(struct cpuidle_device *dev, */ idx--; for (; idx >= 0; idx--) { - cx = cpuidle_get_statedata(&dev->states[idx]); + cx = cpuidle_get_statedata(&dev->states_usage[idx]); if ((cx->valid) && (cx->mpu_state >= mpu_deepest_state) && (cx->core_state >= core_deepest_state)) { - next = &dev->states[idx]; + next_index = idx; break; } } /* * C1 is always valid. - * So, no need to check for 'next==NULL' outside this loop. + * So, no need to check for 'next_index == -1' outside + * this loop. */ } - return next; + return next_index; } /** * omap3_enter_idle_bm - Checks for any bus activity * @dev: cpuidle device - * @state: The target state to be programmed + * @drv: cpuidle driver + * @index: array index of target state to be programmed * * This function checks for any pending activity and then programs * the device to the specified or a safer state. */ static int omap3_enter_idle_bm(struct cpuidle_device *dev, - struct cpuidle_state *state) + struct cpuidle_driver *drv, + int index) { - struct cpuidle_state *new_state; + int new_state_idx; u32 core_next_state, per_next_state = 0, per_saved_state = 0, cam_state; struct omap3_idle_statedata *cx; int ret; if (!omap3_can_sleep()) { - new_state = dev->safe_state; + new_state_idx = drv->safe_state_index; goto select_state; } @@ -237,7 +255,7 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev, */ cam_state = pwrdm_read_pwrst(cam_pd); if (cam_state == PWRDM_POWER_ON) { - new_state = dev->safe_state; + new_state_idx = drv->safe_state_index; goto select_state; } @@ -253,7 +271,7 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev, * Prevent PER off if CORE is not in retention or off as this * would disable PER wakeups completely. */ - cx = cpuidle_get_statedata(state); + cx = cpuidle_get_statedata(&dev->states_usage[index]); core_next_state = cx->core_state; per_next_state = per_saved_state = pwrdm_read_next_pwrst(per_pd); if ((per_next_state == PWRDM_POWER_OFF) && @@ -264,11 +282,10 @@ static int omap3_enter_idle_bm(struct cpuidle_device *dev, if (per_next_state != per_saved_state) pwrdm_set_next_pwrst(per_pd, per_next_state); - new_state = next_valid_state(dev, state); + new_state_idx = next_valid_state(dev, drv, index); select_state: - dev->last_state = new_state; - ret = omap3_enter_idle(dev, new_state); + ret = omap3_enter_idle(dev, drv, new_state_idx); /* Restore original PER state if it was modified */ if (per_next_state != per_saved_state) @@ -301,22 +318,31 @@ struct cpuidle_driver omap3_idle_driver = { .owner = THIS_MODULE, }; -/* Helper to fill the C-state common data and register the driver_data */ -static inline struct omap3_idle_statedata *_fill_cstate( - struct cpuidle_device *dev, +/* Helper to fill the C-state common data*/ +static inline void _fill_cstate(struct cpuidle_driver *drv, int idx, const char *descr) { - struct omap3_idle_statedata *cx = &omap3_idle_data[idx]; - struct cpuidle_state *state = &dev->states[idx]; + struct cpuidle_state *state = &drv->states[idx]; state->exit_latency = cpuidle_params_table[idx].exit_latency; state->target_residency = cpuidle_params_table[idx].target_residency; state->flags = CPUIDLE_FLAG_TIME_VALID; state->enter = omap3_enter_idle_bm; - cx->valid = cpuidle_params_table[idx].valid; sprintf(state->name, "C%d", idx + 1); strncpy(state->desc, descr, CPUIDLE_DESC_LEN); - cpuidle_set_statedata(state, cx); + +} + +/* Helper to register the driver_data */ +static inline struct omap3_idle_statedata *_fill_cstate_usage( + struct cpuidle_device *dev, + int idx) +{ + struct omap3_idle_statedata *cx = &omap3_idle_data[idx]; + struct cpuidle_state_usage *state_usage = &dev->states_usage[idx]; + + cx->valid = cpuidle_params_table[idx].valid; + cpuidle_set_statedata(state_usage, cx); return cx; } @@ -330,6 +356,7 @@ static inline struct omap3_idle_statedata *_fill_cstate( int __init omap3_idle_init(void) { struct cpuidle_device *dev; + struct cpuidle_driver *drv = &omap3_idle_driver; struct omap3_idle_statedata *cx; mpu_pd = pwrdm_lookup("mpu_pwrdm"); @@ -337,44 +364,52 @@ int __init omap3_idle_init(void) per_pd = pwrdm_lookup("per_pwrdm"); cam_pd = pwrdm_lookup("cam_pwrdm"); - cpuidle_register_driver(&omap3_idle_driver); + + drv->safe_state_index = -1; dev = &per_cpu(omap3_idle_dev, smp_processor_id()); /* C1 . MPU WFI + Core active */ - cx = _fill_cstate(dev, 0, "MPU ON + CORE ON"); - (&dev->states[0])->enter = omap3_enter_idle; - dev->safe_state = &dev->states[0]; + _fill_cstate(drv, 0, "MPU ON + CORE ON"); + (&drv->states[0])->enter = omap3_enter_idle; + drv->safe_state_index = 0; + cx = _fill_cstate_usage(dev, 0); cx->valid = 1; /* C1 is always valid */ cx->mpu_state = PWRDM_POWER_ON; cx->core_state = PWRDM_POWER_ON; /* C2 . MPU WFI + Core inactive */ - cx = _fill_cstate(dev, 1, "MPU ON + CORE ON"); + _fill_cstate(drv, 1, "MPU ON + CORE ON"); + cx = _fill_cstate_usage(dev, 1); cx->mpu_state = PWRDM_POWER_ON; cx->core_state = PWRDM_POWER_ON; /* C3 . MPU CSWR + Core inactive */ - cx = _fill_cstate(dev, 2, "MPU RET + CORE ON"); + _fill_cstate(drv, 2, "MPU RET + CORE ON"); + cx = _fill_cstate_usage(dev, 2); cx->mpu_state = PWRDM_POWER_RET; cx->core_state = PWRDM_POWER_ON; /* C4 . MPU OFF + Core inactive */ - cx = _fill_cstate(dev, 3, "MPU OFF + CORE ON"); + _fill_cstate(drv, 3, "MPU OFF + CORE ON"); + cx = _fill_cstate_usage(dev, 3); cx->mpu_state = PWRDM_POWER_OFF; cx->core_state = PWRDM_POWER_ON; /* C5 . MPU RET + Core RET */ - cx = _fill_cstate(dev, 4, "MPU RET + CORE RET"); + _fill_cstate(drv, 4, "MPU RET + CORE RET"); + cx = _fill_cstate_usage(dev, 4); cx->mpu_state = PWRDM_POWER_RET; cx->core_state = PWRDM_POWER_RET; /* C6 . MPU OFF + Core RET */ - cx = _fill_cstate(dev, 5, "MPU OFF + CORE RET"); + _fill_cstate(drv, 5, "MPU OFF + CORE RET"); + cx = _fill_cstate_usage(dev, 5); cx->mpu_state = PWRDM_POWER_OFF; cx->core_state = PWRDM_POWER_RET; /* C7 . MPU OFF + Core OFF */ - cx = _fill_cstate(dev, 6, "MPU OFF + CORE OFF"); + _fill_cstate(drv, 6, "MPU OFF + CORE OFF"); + cx = _fill_cstate_usage(dev, 6); /* * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot * enable OFF mode in a stable form for previous revisions. @@ -388,6 +423,9 @@ int __init omap3_idle_init(void) cx->mpu_state = PWRDM_POWER_OFF; cx->core_state = PWRDM_POWER_OFF; + drv->state_count = OMAP3_NUM_STATES; + cpuidle_register_driver(&omap3_idle_driver); + dev->state_count = OMAP3_NUM_STATES; if (cpuidle_register_device(dev)) { printk(KERN_ERR "%s: CPUidle register device failed\n", diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 68ec03152d5..c15cfada5f1 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -318,18 +318,10 @@ static inline void omap_init_audio(void) {} #if defined(CONFIG_SND_OMAP_SOC_MCPDM) || \ defined(CONFIG_SND_OMAP_SOC_MCPDM_MODULE) -static struct omap_device_pm_latency omap_mcpdm_latency[] = { - { - .deactivate_func = omap_device_idle_hwmods, - .activate_func = omap_device_enable_hwmods, - .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST, - }, -}; - static void omap_init_mcpdm(void) { struct omap_hwmod *oh; - struct omap_device *od; + struct platform_device *pdev; oh = omap_hwmod_lookup("mcpdm"); if (!oh) { @@ -337,11 +329,8 @@ static void omap_init_mcpdm(void) return; } - od = omap_device_build("omap-mcpdm", -1, oh, NULL, 0, - omap_mcpdm_latency, - ARRAY_SIZE(omap_mcpdm_latency), 0); - if (IS_ERR(od)) - printk(KERN_ERR "Could not build omap_device for omap-mcpdm-dai\n"); + pdev = omap_device_build("omap-mcpdm", -1, oh, NULL, 0, NULL, 0, 0); + WARN(IS_ERR(pdev), "Can't build omap_device for omap-mcpdm.\n"); } #else static inline void omap_init_mcpdm(void) {} diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c index 4036821a01f..dce9905d64b 100644 --- a/arch/arm/mach-omap2/display.c +++ b/arch/arm/mach-omap2/display.c @@ -15,6 +15,7 @@ * GNU General Public License for more details. */ +#include <linux/string.h> #include <linux/kernel.h> #include <linux/init.h> #include <linux/platform_device.h> @@ -26,8 +27,35 @@ #include <plat/omap_hwmod.h> #include <plat/omap_device.h> #include <plat/omap-pm.h> +#include <plat/common.h> #include "control.h" +#include "display.h" + +#define DISPC_CONTROL 0x0040 +#define DISPC_CONTROL2 0x0238 +#define DISPC_IRQSTATUS 0x0018 + +#define DSS_SYSCONFIG 0x10 +#define DSS_SYSSTATUS 0x14 +#define DSS_CONTROL 0x40 +#define DSS_SDI_CONTROL 0x44 +#define DSS_PLL_CONTROL 0x48 + +#define LCD_EN_MASK (0x1 << 0) +#define DIGIT_EN_MASK (0x1 << 1) + +#define FRAMEDONE_IRQ_SHIFT 0 +#define EVSYNC_EVEN_IRQ_SHIFT 2 +#define EVSYNC_ODD_IRQ_SHIFT 3 +#define FRAMEDONE2_IRQ_SHIFT 22 +#define FRAMEDONETV_IRQ_SHIFT 24 + +/* + * FRAMEDONE_IRQ_TIMEOUT: how long (in milliseconds) to wait during DISPC + * reset before deciding that something has gone wrong + */ +#define FRAMEDONE_IRQ_TIMEOUT 100 static struct platform_device omap_display_device = { .name = "omapdss", @@ -171,3 +199,135 @@ int __init omap_display_init(struct omap_dss_board_info *board_data) return r; } + +static void dispc_disable_outputs(void) +{ + u32 v, irq_mask = 0; + bool lcd_en, digit_en, lcd2_en = false; + int i; + struct omap_dss_dispc_dev_attr *da; + struct omap_hwmod *oh; + + oh = omap_hwmod_lookup("dss_dispc"); + if (!oh) { + WARN(1, "display: could not disable outputs during reset - could not find dss_dispc hwmod\n"); + return; + } + + if (!oh->dev_attr) { + pr_err("display: could not disable outputs during reset due to missing dev_attr\n"); + return; + } + + da = (struct omap_dss_dispc_dev_attr *)oh->dev_attr; + + /* store value of LCDENABLE and DIGITENABLE bits */ + v = omap_hwmod_read(oh, DISPC_CONTROL); + lcd_en = v & LCD_EN_MASK; + digit_en = v & DIGIT_EN_MASK; + + /* store value of LCDENABLE for LCD2 */ + if (da->manager_count > 2) { + v = omap_hwmod_read(oh, DISPC_CONTROL2); + lcd2_en = v & LCD_EN_MASK; + } + + if (!(lcd_en | digit_en | lcd2_en)) + return; /* no managers currently enabled */ + + /* + * If any manager was enabled, we need to disable it before + * DSS clocks are disabled or DISPC module is reset + */ + if (lcd_en) + irq_mask |= 1 << FRAMEDONE_IRQ_SHIFT; + + if (digit_en) { + if (da->has_framedonetv_irq) { + irq_mask |= 1 << FRAMEDONETV_IRQ_SHIFT; + } else { + irq_mask |= 1 << EVSYNC_EVEN_IRQ_SHIFT | + 1 << EVSYNC_ODD_IRQ_SHIFT; + } + } + + if (lcd2_en) + irq_mask |= 1 << FRAMEDONE2_IRQ_SHIFT; + + /* + * clear any previous FRAMEDONE, FRAMEDONETV, + * EVSYNC_EVEN/ODD or FRAMEDONE2 interrupts + */ + omap_hwmod_write(irq_mask, oh, DISPC_IRQSTATUS); + + /* disable LCD and TV managers */ + v = omap_hwmod_read(oh, DISPC_CONTROL); + v &= ~(LCD_EN_MASK | DIGIT_EN_MASK); + omap_hwmod_write(v, oh, DISPC_CONTROL); + + /* disable LCD2 manager */ + if (da->manager_count > 2) { + v = omap_hwmod_read(oh, DISPC_CONTROL2); + v &= ~LCD_EN_MASK; + omap_hwmod_write(v, oh, DISPC_CONTROL2); + } + + i = 0; + while ((omap_hwmod_read(oh, DISPC_IRQSTATUS) & irq_mask) != + irq_mask) { + i++; + if (i > FRAMEDONE_IRQ_TIMEOUT) { + pr_err("didn't get FRAMEDONE1/2 or TV interrupt\n"); + break; + } + mdelay(1); + } +} + +#define MAX_MODULE_SOFTRESET_WAIT 10000 +int omap_dss_reset(struct omap_hwmod *oh) +{ + struct omap_hwmod_opt_clk *oc; + int c = 0; + int i, r; + + if (!(oh->class->sysc->sysc_flags & SYSS_HAS_RESET_STATUS)) { + pr_err("dss_core: hwmod data doesn't contain reset data\n"); + return -EINVAL; + } + + for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++) + if (oc->_clk) + clk_enable(oc->_clk); + + dispc_disable_outputs(); + + /* clear SDI registers */ + if (cpu_is_omap3430()) { + omap_hwmod_write(0x0, oh, DSS_SDI_CONTROL); + omap_hwmod_write(0x0, oh, DSS_PLL_CONTROL); + } + + /* + * clear DSS_CONTROL register to switch DSS clock sources to + * PRCM clock, if any + */ + omap_hwmod_write(0x0, oh, DSS_CONTROL); + + omap_test_timeout((omap_hwmod_read(oh, oh->class->sysc->syss_offs) + & SYSS_RESETDONE_MASK), + MAX_MODULE_SOFTRESET_WAIT, c); + + if (c == MAX_MODULE_SOFTRESET_WAIT) + pr_warning("dss_core: waiting for reset to finish failed\n"); + else + pr_debug("dss_core: softreset done\n"); + + for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++) + if (oc->_clk) + clk_disable(oc->_clk); + + r = (c == MAX_MODULE_SOFTRESET_WAIT) ? -ETIMEDOUT : 0; + + return r; +} diff --git a/arch/arm/mach-omap2/display.h b/arch/arm/mach-omap2/display.h new file mode 100644 index 00000000000..b871b017b35 --- /dev/null +++ b/arch/arm/mach-omap2/display.h @@ -0,0 +1,29 @@ +/* + * display.h - OMAP2+ integration-specific DSS header + * + * Copyright (C) 2011 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __ARCH_ARM_MACH_OMAP2_DISPLAY_H +#define __ARCH_ARM_MACH_OMAP2_DISPLAY_H + +#include <linux/kernel.h> + +struct omap_dss_dispc_dev_attr { + u8 manager_count; + bool has_framedonetv_irq; +}; + +#endif diff --git a/arch/arm/mach-omap2/dpll3xxx.c b/arch/arm/mach-omap2/dpll3xxx.c index f77022be783..fc56745676f 100644 --- a/arch/arm/mach-omap2/dpll3xxx.c +++ b/arch/arm/mach-omap2/dpll3xxx.c @@ -390,7 +390,8 @@ int omap3_noncore_dpll_enable(struct clk *clk) * propagating? */ if (!r) - clk->rate = omap2_get_dpll_rate(clk); + clk->rate = (clk->recalc) ? clk->recalc(clk) : + omap2_get_dpll_rate(clk); return r; } @@ -424,6 +425,7 @@ void omap3_noncore_dpll_disable(struct clk *clk) int omap3_noncore_dpll_set_rate(struct clk *clk, unsigned long rate) { struct clk *new_parent = NULL; + unsigned long hw_rate; u16 freqsel = 0; struct dpll_data *dd; int ret; @@ -435,7 +437,8 @@ int omap3_noncore_dpll_set_rate(struct clk *clk, unsigned long rate) if (!dd) return -EINVAL; - if (rate == omap2_get_dpll_rate(clk)) + hw_rate = (clk->recalc) ? clk->recalc(clk) : omap2_get_dpll_rate(clk); + if (rate == hw_rate) return 0; /* @@ -455,7 +458,7 @@ int omap3_noncore_dpll_set_rate(struct clk *clk, unsigned long rate) new_parent = dd->clk_bypass; } else { if (dd->last_rounded_rate != rate) - omap2_dpll_round_rate(clk, rate); + rate = clk->round_rate(clk, rate); if (dd->last_rounded_rate == 0) return -EINVAL; diff --git a/arch/arm/mach-omap2/dpll44xx.c b/arch/arm/mach-omap2/dpll44xx.c index 4e4da6160d0..9c6a296b3dc 100644 --- a/arch/arm/mach-omap2/dpll44xx.c +++ b/arch/arm/mach-omap2/dpll44xx.c @@ -19,6 +19,7 @@ #include <plat/clock.h> #include "clock.h" +#include "clock44xx.h" #include "cm-regbits-44xx.h" /* Supported only on OMAP4 */ @@ -82,3 +83,71 @@ const struct clkops clkops_omap4_dpllmx_ops = { .deny_idle = omap4_dpllmx_deny_gatectrl, }; +/** + * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit + * @clk: struct clk * of the DPLL to compute the rate for + * + * Compute the output rate for the OMAP4 DPLL represented by @clk. + * Takes the REGM4XEN bit into consideration, which is needed for the + * OMAP4 ABE DPLL. Returns the DPLL's output rate (before M-dividers) + * upon success, or 0 upon error. + */ +unsigned long omap4_dpll_regm4xen_recalc(struct clk *clk) +{ + u32 v; + unsigned long rate; + struct dpll_data *dd; + + if (!clk || !clk->dpll_data) + return 0; + + dd = clk->dpll_data; + + rate = omap2_get_dpll_rate(clk); + + /* regm4xen adds a multiplier of 4 to DPLL calculations */ + v = __raw_readl(dd->control_reg); + if (v & OMAP4430_DPLL_REGM4XEN_MASK) + rate *= OMAP4430_REGM4XEN_MULT; + + return rate; +} + +/** + * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit + * @clk: struct clk * of the DPLL to round a rate for + * @target_rate: the desired rate of the DPLL + * + * Compute the rate that would be programmed into the DPLL hardware + * for @clk if set_rate() were to be provided with the rate + * @target_rate. Takes the REGM4XEN bit into consideration, which is + * needed for the OMAP4 ABE DPLL. Returns the rounded rate (before + * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or + * ~0 if an error occurred in omap2_dpll_round_rate(). + */ +long omap4_dpll_regm4xen_round_rate(struct clk *clk, unsigned long target_rate) +{ + u32 v; + struct dpll_data *dd; + long r; + + if (!clk || !clk->dpll_data) + return -EINVAL; + + dd = clk->dpll_data; + + /* regm4xen adds a multiplier of 4 to DPLL calculations */ + v = __raw_readl(dd->control_reg) & OMAP4430_DPLL_REGM4XEN_MASK; + + if (v) + target_rate = target_rate / OMAP4430_REGM4XEN_MULT; + + r = omap2_dpll_round_rate(clk, target_rate); + if (r == ~0) + return r; + + if (v) + clk->dpll_data->last_rounded_rate *= OMAP4430_REGM4XEN_MULT; + + return clk->dpll_data->last_rounded_rate; +} diff --git a/arch/arm/mach-omap2/dsp.c b/arch/arm/mach-omap2/dsp.c index 911cd2e68d4..74f18f2952d 100644 --- a/arch/arm/mach-omap2/dsp.c +++ b/arch/arm/mach-omap2/dsp.c @@ -18,6 +18,7 @@ * of the OMAP PM core code. */ +#include <linux/module.h> #include <linux/platform_device.h> #include "cm2xxx_3xxx.h" #include "prm2xxx_3xxx.h" diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c index d776ded9830..5cdce10d618 100644 --- a/arch/arm/mach-omap2/gpmc-onenand.c +++ b/arch/arm/mach-omap2/gpmc-onenand.c @@ -10,6 +10,7 @@ * published by the Free Software Foundation. */ +#include <linux/string.h> #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/mtd/onenand_regs.h> diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index 77085847e4e..f4a1020559a 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -129,15 +129,11 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot, * Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the * card with Vcc regulator (from twl4030 or whatever). OMAP has both * 1.8V and 3.0V modes, controlled by the PBIAS register. - * - * In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which - * is most naturally TWL VSIM; those pins also use PBIAS. - * - * FIXME handle VMMC1A as needed ... */ reg = omap4_ctrl_pad_readl(control_pbias_offset); reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK | + OMAP4_MMC1_PBIASLITE_VMODE_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } @@ -172,12 +168,6 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, reg &= ~(OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } - } else { - reg = omap4_ctrl_pad_readl(control_pbias_offset); - reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_MMC1_PBIASLITE_VMODE_MASK); - omap4_ctrl_pad_writel(reg, control_pbias_offset); } } @@ -489,7 +479,7 @@ void __init omap2_hsmmc_init(struct omap2_hsmmc_info *controllers) OMAP4_SDMMC1_PUSTRENGTH_GRP1_MASK); reg &= ~(OMAP4_SDMMC1_PUSTRENGTH_GRP2_MASK | OMAP4_SDMMC1_PUSTRENGTH_GRP3_MASK); - reg |= (OMAP4_USBC1_DR0_SPEEDCTRL_MASK| + reg |= (OMAP4_SDMMC1_DR0_SPEEDCTRL_MASK | OMAP4_SDMMC1_DR1_SPEEDCTRL_MASK | OMAP4_SDMMC1_DR2_SPEEDCTRL_MASK); omap4_ctrl_pad_writel(reg, control_mmc1); diff --git a/arch/arm/mach-omap2/hwspinlock.c b/arch/arm/mach-omap2/hwspinlock.c index 36e21091b06..454dfce125c 100644 --- a/arch/arm/mach-omap2/hwspinlock.c +++ b/arch/arm/mach-omap2/hwspinlock.c @@ -19,10 +19,15 @@ #include <linux/kernel.h> #include <linux/init.h> #include <linux/err.h> +#include <linux/hwspinlock.h> #include <plat/omap_hwmod.h> #include <plat/omap_device.h> +static struct hwspinlock_pdata omap_hwspinlock_pdata __initdata = { + .base_id = 0, +}; + int __init hwspinlocks_init(void) { int retval = 0; @@ -40,7 +45,9 @@ int __init hwspinlocks_init(void) if (oh == NULL) return -EINVAL; - pdev = omap_device_build(dev_name, 0, oh, NULL, 0, NULL, 0, false); + pdev = omap_device_build(dev_name, 0, oh, &omap_hwspinlock_pdata, + sizeof(struct hwspinlock_pdata), + NULL, 0, false); if (IS_ERR(pdev)) { pr_err("Can't build omap_device for %s:%s\n", dev_name, oh_name); diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index d27daf921c7..7f47092a193 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -187,8 +187,11 @@ static void __init omap3_check_features(void) OMAP3_CHECK_FEATURE(status, ISP); if (cpu_is_omap3630()) omap_features |= OMAP3_HAS_192MHZ_CLK; - if (!cpu_is_omap3505() && !cpu_is_omap3517()) + if (cpu_is_omap3430() || cpu_is_omap3630()) omap_features |= OMAP3_HAS_IO_WAKEUP; + if (cpu_is_omap3630() || omap_rev() == OMAP3430_REV_ES3_1 || + omap_rev() == OMAP3430_REV_ES3_1_2) + omap_features |= OMAP3_HAS_IO_CHAIN_CTRL; omap_features |= OMAP3_HAS_SDRC; diff --git a/arch/arm/mach-omap2/include/mach/ctrl_module_pad_core_44xx.h b/arch/arm/mach-omap2/include/mach/ctrl_module_pad_core_44xx.h index c88420de115..1e2d3322f33 100644 --- a/arch/arm/mach-omap2/include/mach/ctrl_module_pad_core_44xx.h +++ b/arch/arm/mach-omap2/include/mach/ctrl_module_pad_core_44xx.h @@ -941,10 +941,10 @@ #define OMAP4_DSI2_LANEENABLE_MASK (0x7 << 29) #define OMAP4_DSI1_LANEENABLE_SHIFT 24 #define OMAP4_DSI1_LANEENABLE_MASK (0x1f << 24) -#define OMAP4_DSI1_PIPD_SHIFT 19 -#define OMAP4_DSI1_PIPD_MASK (0x1f << 19) -#define OMAP4_DSI2_PIPD_SHIFT 14 -#define OMAP4_DSI2_PIPD_MASK (0x1f << 14) +#define OMAP4_DSI2_PIPD_SHIFT 19 +#define OMAP4_DSI2_PIPD_MASK (0x1f << 19) +#define OMAP4_DSI1_PIPD_SHIFT 14 +#define OMAP4_DSI1_PIPD_MASK (0x1f << 14) /* CONTROL_MCBSPLP */ #define OMAP4_ALBCTRLRX_FSX_SHIFT 31 diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index a5d8dce2a70..25d20ced03e 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -359,6 +359,7 @@ static void __init omap_hwmod_init_postsetup(void) omap_pm_if_early_init(); } +#ifdef CONFIG_ARCH_OMAP2 void __init omap2420_init_early(void) { omap2_set_globals_242x(); @@ -382,11 +383,13 @@ void __init omap2430_init_early(void) omap_hwmod_init_postsetup(); omap2430_clk_init(); } +#endif /* * Currently only board-omap3beagle.c should call this because of the * same machine_id for 34xx and 36xx beagle.. Will get fixed with DT. */ +#ifdef CONFIG_ARCH_OMAP3 void __init omap3_init_early(void) { omap2_set_globals_3xxx(); @@ -430,7 +433,9 @@ void __init ti816x_init_early(void) omap_hwmod_init_postsetup(); omap3xxx_clk_init(); } +#endif +#ifdef CONFIG_ARCH_OMAP4 void __init omap4430_init_early(void) { omap2_set_globals_443x(); @@ -442,6 +447,7 @@ void __init omap4430_init_early(void) omap_hwmod_init_postsetup(); omap4xxx_clk_init(); } +#endif void __init omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0, struct omap_sdrc_params *sdrc_cs1) diff --git a/arch/arm/mach-omap2/io.h b/arch/arm/mach-omap2/io.h deleted file mode 100644 index e69de29bb2d..00000000000 --- a/arch/arm/mach-omap2/io.h +++ /dev/null diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c index 86d564a640b..609ea2ded7e 100644 --- a/arch/arm/mach-omap2/mailbox.c +++ b/arch/arm/mach-omap2/mailbox.c @@ -10,6 +10,7 @@ * for more details. */ +#include <linux/module.h> #include <linux/clk.h> #include <linux/err.h> #include <linux/platform_device.h> diff --git a/arch/arm/mach-omap2/omap-iommu.c b/arch/arm/mach-omap2/omap-iommu.c index e61feadcda4..b8822048e40 100644 --- a/arch/arm/mach-omap2/omap-iommu.c +++ b/arch/arm/mach-omap2/omap-iommu.c @@ -10,6 +10,7 @@ * published by the Free Software Foundation. */ +#include <linux/module.h> #include <linux/platform_device.h> #include <plat/iommu.h> diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index d7138070508..207a2ff9a8c 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -749,7 +749,7 @@ static int _count_mpu_irqs(struct omap_hwmod *oh) ohii = &oh->mpu_irqs[i++]; } while (ohii->irq != -1); - return i; + return i-1; } /** @@ -772,7 +772,7 @@ static int _count_sdma_reqs(struct omap_hwmod *oh) ohdi = &oh->sdma_reqs[i++]; } while (ohdi->dma_req != -1); - return i; + return i-1; } /** @@ -795,7 +795,7 @@ static int _count_ocp_if_addr_spaces(struct omap_hwmod_ocp_if *os) mem = &os->addr[i++]; } while (mem->pa_start != mem->pa_end); - return i; + return i-1; } /** @@ -2625,7 +2625,7 @@ ohsps_unlock: * Returns the context loss count of the powerdomain assocated with @oh * upon success, or zero if no powerdomain exists for @oh. */ -u32 omap_hwmod_get_context_loss_count(struct omap_hwmod *oh) +int omap_hwmod_get_context_loss_count(struct omap_hwmod *oh) { struct powerdomain *pwrdm; int ret = 0; diff --git a/arch/arm/mach-omap2/omap_hwmod_2420_data.c b/arch/arm/mach-omap2/omap_hwmod_2420_data.c index 6d720621352..a5409ce3f32 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2420_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2420_data.c @@ -875,6 +875,10 @@ static struct omap_hwmod_ocp_if *omap2420_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "tv_clk", .clk = "dss_54m_fck" }, { .role = "sys_clk", .clk = "dss2_fck" }, }; @@ -899,7 +903,7 @@ static struct omap_hwmod omap2420_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap2420_dss_slaves), .masters = omap2420_dss_masters, .masters_cnt = ARRAY_SIZE(omap2420_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; /* l4_core -> dss_dispc */ @@ -939,6 +943,7 @@ static struct omap_hwmod omap2420_dss_dispc_hwmod = { .slaves = omap2420_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap2420_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* l4_core -> dss_rfbi */ @@ -961,6 +966,10 @@ static struct omap_hwmod_ocp_if *omap2420_dss_rfbi_slaves[] = { &omap2420_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap2420_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -972,6 +981,8 @@ static struct omap_hwmod omap2420_dss_rfbi_hwmod = { .module_offs = CORE_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap2420_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap2420_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -981,7 +992,7 @@ static struct omap_hwmod omap2420_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap2420_l4_core__dss_venc = { .master = &omap2420_l4_core_hwmod, .slave = &omap2420_dss_venc_hwmod, - .clk = "dss_54m_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .fw = { .omap2 = { @@ -1001,7 +1012,7 @@ static struct omap_hwmod_ocp_if *omap2420_dss_venc_slaves[] = { static struct omap_hwmod omap2420_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_fck", + .main_clk = "dss_54m_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c index a2580d01c3f..c4f56cb60d7 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c @@ -942,6 +942,10 @@ static struct omap_hwmod_ocp_if *omap2430_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "tv_clk", .clk = "dss_54m_fck" }, { .role = "sys_clk", .clk = "dss2_fck" }, }; @@ -966,7 +970,7 @@ static struct omap_hwmod omap2430_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap2430_dss_slaves), .masters = omap2430_dss_masters, .masters_cnt = ARRAY_SIZE(omap2430_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; /* l4_core -> dss_dispc */ @@ -1000,6 +1004,7 @@ static struct omap_hwmod omap2430_dss_dispc_hwmod = { .slaves = omap2430_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap2430_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* l4_core -> dss_rfbi */ @@ -1016,6 +1021,10 @@ static struct omap_hwmod_ocp_if *omap2430_dss_rfbi_slaves[] = { &omap2430_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap2430_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -1027,6 +1036,8 @@ static struct omap_hwmod omap2430_dss_rfbi_hwmod = { .module_offs = CORE_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap2430_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap2430_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -1036,7 +1047,7 @@ static struct omap_hwmod omap2430_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap2430_l4_core__dss_venc = { .master = &omap2430_l4_core_hwmod, .slave = &omap2430_dss_venc_hwmod, - .clk = "dss_54m_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .flags = OCPIF_SWSUP_IDLE, .user = OCP_USER_MPU | OCP_USER_SDMA, @@ -1050,7 +1061,7 @@ static struct omap_hwmod_ocp_if *omap2430_dss_venc_slaves[] = { static struct omap_hwmod omap2430_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_fck", + .main_clk = "dss_54m_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, diff --git a/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c index c451729d289..c11273da5dc 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c @@ -11,6 +11,7 @@ #include <plat/omap_hwmod.h> #include <plat/serial.h> #include <plat/dma.h> +#include <plat/common.h> #include <mach/irqs.h> @@ -43,13 +44,15 @@ static struct omap_hwmod_class_sysconfig omap2_dss_sysc = { .rev_offs = 0x0000, .sysc_offs = 0x0010, .syss_offs = 0x0014, - .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE), + .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE | + SYSS_HAS_RESET_STATUS), .sysc_fields = &omap_hwmod_sysc_type1, }; struct omap_hwmod_class omap2_dss_hwmod_class = { .name = "dss", .sysc = &omap2_dss_sysc, + .reset = omap_dss_reset, }; /* diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index 3008e1672c7..7f8915ad509 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -1369,9 +1369,14 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { - { .role = "tv_clk", .clk = "dss_tv_fck" }, - { .role = "video_clk", .clk = "dss_96m_fck" }, + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "sys_clk", .clk = "dss2_alwon_fck" }, + { .role = "tv_clk", .clk = "dss_tv_fck" }, + /* required only on OMAP3430 */ + { .role = "tv_dac_clk", .clk = "dss_96m_fck" }, }; static struct omap_hwmod omap3430es1_dss_core_hwmod = { @@ -1394,11 +1399,12 @@ static struct omap_hwmod omap3430es1_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap3430es1_dss_slaves), .masters = omap3xxx_dss_masters, .masters_cnt = ARRAY_SIZE(omap3xxx_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; static struct omap_hwmod omap3xxx_dss_core_hwmod = { .name = "dss_core", + .flags = HWMOD_CONTROL_OPT_CLKS_IN_RESET, .class = &omap2_dss_hwmod_class, .main_clk = "dss1_alwon_fck", /* instead of dss_fck */ .sdma_reqs = omap3xxx_dss_sdma_chs, @@ -1456,6 +1462,7 @@ static struct omap_hwmod omap3xxx_dss_dispc_hwmod = { .slaves = omap3xxx_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* @@ -1486,6 +1493,7 @@ static struct omap_hwmod_addr_space omap3xxx_dss_dsi1_addrs[] = { static struct omap_hwmod_ocp_if omap3xxx_l4_core__dss_dsi1 = { .master = &omap3xxx_l4_core_hwmod, .slave = &omap3xxx_dss_dsi1_hwmod, + .clk = "dss_ick", .addr = omap3xxx_dss_dsi1_addrs, .fw = { .omap2 = { @@ -1502,6 +1510,10 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_dsi1_slaves[] = { &omap3xxx_l4_core__dss_dsi1, }; +static struct omap_hwmod_opt_clk dss_dsi1_opt_clks[] = { + { .role = "sys_clk", .clk = "dss2_alwon_fck" }, +}; + static struct omap_hwmod omap3xxx_dss_dsi1_hwmod = { .name = "dss_dsi1", .class = &omap3xxx_dsi_hwmod_class, @@ -1514,6 +1526,8 @@ static struct omap_hwmod omap3xxx_dss_dsi1_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_dsi1_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_dsi1_opt_clks), .slaves = omap3xxx_dss_dsi1_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_dsi1_slaves), .flags = HWMOD_NO_IDLEST, @@ -1540,6 +1554,10 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_rfbi_slaves[] = { &omap3xxx_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -1551,6 +1569,8 @@ static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap3xxx_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -1560,7 +1580,7 @@ static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap3xxx_l4_core__dss_venc = { .master = &omap3xxx_l4_core_hwmod, .slave = &omap3xxx_dss_venc_hwmod, - .clk = "dss_tv_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .fw = { .omap2 = { @@ -1578,10 +1598,15 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_venc_slaves[] = { &omap3xxx_l4_core__dss_venc, }; +static struct omap_hwmod_opt_clk dss_venc_opt_clks[] = { + /* required only on OMAP3430 */ + { .role = "tv_dac_clk", .clk = "dss_96m_fck" }, +}; + static struct omap_hwmod omap3xxx_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_alwon_fck", + .main_clk = "dss_tv_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, @@ -1589,6 +1614,8 @@ static struct omap_hwmod omap3xxx_dss_venc_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_venc_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_venc_opt_clks), .slaves = omap3xxx_dss_venc_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_venc_slaves), .flags = HWMOD_NO_IDLEST, @@ -3159,7 +3186,6 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_mmc2_hwmod, &omap3xxx_mmc3_hwmod, &omap3xxx_mpu_hwmod, - &omap3xxx_iva_hwmod, &omap3xxx_timer1_hwmod, &omap3xxx_timer2_hwmod, @@ -3188,8 +3214,6 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_i2c1_hwmod, &omap3xxx_i2c2_hwmod, &omap3xxx_i2c3_hwmod, - &omap34xx_sr1_hwmod, - &omap34xx_sr2_hwmod, /* gpio class */ &omap3xxx_gpio1_hwmod, @@ -3211,8 +3235,6 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_mcbsp2_sidetone_hwmod, &omap3xxx_mcbsp3_sidetone_hwmod, - /* mailbox class */ - &omap3xxx_mailbox_hwmod, /* mcspi class */ &omap34xx_mcspi1, @@ -3225,31 +3247,39 @@ static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { /* 3430ES1-only hwmods */ static __initdata struct omap_hwmod *omap3430es1_hwmods[] = { + &omap3xxx_iva_hwmod, &omap3430es1_dss_core_hwmod, + &omap3xxx_mailbox_hwmod, NULL }; /* 3430ES2+-only hwmods */ static __initdata struct omap_hwmod *omap3430es2plus_hwmods[] = { + &omap3xxx_iva_hwmod, &omap3xxx_dss_core_hwmod, &omap3xxx_usbhsotg_hwmod, + &omap3xxx_mailbox_hwmod, NULL }; /* 34xx-only hwmods (all ES revisions) */ static __initdata struct omap_hwmod *omap34xx_hwmods[] = { + &omap3xxx_iva_hwmod, &omap34xx_sr1_hwmod, &omap34xx_sr2_hwmod, + &omap3xxx_mailbox_hwmod, NULL }; /* 36xx-only hwmods (all ES revisions) */ static __initdata struct omap_hwmod *omap36xx_hwmods[] = { + &omap3xxx_iva_hwmod, &omap3xxx_uart4_hwmod, &omap3xxx_dss_core_hwmod, &omap36xx_sr1_hwmod, &omap36xx_sr2_hwmod, &omap3xxx_usbhsotg_hwmod, + &omap3xxx_mailbox_hwmod, NULL }; @@ -3267,7 +3297,7 @@ int __init omap3xxx_hwmod_init(void) /* Register hwmods common to all OMAP3 */ r = omap_hwmod_register(omap3xxx_hwmods); - if (!r) + if (r < 0) return r; rev = omap_rev(); @@ -3292,7 +3322,7 @@ int __init omap3xxx_hwmod_init(void) }; r = omap_hwmod_register(h); - if (!r) + if (r < 0) return r; /* diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 7695e5d4331..daaf165af69 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -30,6 +30,7 @@ #include <plat/mmc.h> #include <plat/i2c.h> #include <plat/dmtimer.h> +#include <plat/common.h> #include "omap_hwmod_common_data.h" @@ -1187,6 +1188,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_dss_sysc = { static struct omap_hwmod_class omap44xx_dss_hwmod_class = { .name = "dss", .sysc = &omap44xx_dss_sysc, + .reset = omap_dss_reset, }; /* dss */ @@ -1240,12 +1242,12 @@ static struct omap_hwmod_ocp_if *omap44xx_dss_slaves[] = { static struct omap_hwmod_opt_clk dss_opt_clks[] = { { .role = "sys_clk", .clk = "dss_sys_clk" }, { .role = "tv_clk", .clk = "dss_tv_clk" }, - { .role = "dss_clk", .clk = "dss_dss_clk" }, - { .role = "video_clk", .clk = "dss_48mhz_clk" }, + { .role = "hdmi_clk", .clk = "dss_48mhz_clk" }, }; static struct omap_hwmod omap44xx_dss_hwmod = { .name = "dss_core", + .flags = HWMOD_CONTROL_OPT_CLKS_IN_RESET, .class = &omap44xx_dss_hwmod_class, .clkdm_name = "l3_dss_clkdm", .main_clk = "dss_dss_clk", @@ -1325,6 +1327,11 @@ static struct omap_hwmod_addr_space omap44xx_dss_dispc_addrs[] = { { } }; +static struct omap_dss_dispc_dev_attr omap44xx_dss_dispc_dev_attr = { + .manager_count = 3, + .has_framedonetv_irq = 1 +}; + /* l4_per -> dss_dispc */ static struct omap_hwmod_ocp_if omap44xx_l4_per__dss_dispc = { .master = &omap44xx_l4_per_hwmod, @@ -1340,12 +1347,6 @@ static struct omap_hwmod_ocp_if *omap44xx_dss_dispc_slaves[] = { &omap44xx_l4_per__dss_dispc, }; -static struct omap_hwmod_opt_clk dss_dispc_opt_clks[] = { - { .role = "sys_clk", .clk = "dss_sys_clk" }, - { .role = "tv_clk", .clk = "dss_tv_clk" }, - { .role = "hdmi_clk", .clk = "dss_48mhz_clk" }, -}; - static struct omap_hwmod omap44xx_dss_dispc_hwmod = { .name = "dss_dispc", .class = &omap44xx_dispc_hwmod_class, @@ -1359,10 +1360,9 @@ static struct omap_hwmod omap44xx_dss_dispc_hwmod = { .context_offs = OMAP4_RM_DSS_DSS_CONTEXT_OFFSET, }, }, - .opt_clks = dss_dispc_opt_clks, - .opt_clks_cnt = ARRAY_SIZE(dss_dispc_opt_clks), .slaves = omap44xx_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap44xx_dss_dispc_slaves), + .dev_attr = &omap44xx_dss_dispc_dev_attr }; /* @@ -1624,7 +1624,7 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = { .clkdm_name = "l3_dss_clkdm", .mpu_irqs = omap44xx_dss_hdmi_irqs, .sdma_reqs = omap44xx_dss_hdmi_sdma_reqs, - .main_clk = "dss_dss_clk", + .main_clk = "dss_48mhz_clk", .prcm = { .omap4 = { .clkctrl_offs = OMAP4_CM_DSS_DSS_CLKCTRL_OFFSET, @@ -1785,7 +1785,7 @@ static struct omap_hwmod omap44xx_dss_venc_hwmod = { .name = "dss_venc", .class = &omap44xx_venc_hwmod_class, .clkdm_name = "l3_dss_clkdm", - .main_clk = "dss_dss_clk", + .main_clk = "dss_tv_clk", .prcm = { .omap4 = { .clkctrl_offs = OMAP4_CM_DSS_DSS_CLKCTRL_OFFSET, diff --git a/arch/arm/mach-omap2/omap_hwmod_common_data.c b/arch/arm/mach-omap2/omap_hwmod_common_data.c index de832ebc93a..51e5418899f 100644 --- a/arch/arm/mach-omap2/omap_hwmod_common_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_common_data.c @@ -49,3 +49,7 @@ struct omap_hwmod_sysc_fields omap_hwmod_sysc_type2 = { .srst_shift = SYSC_TYPE2_SOFTRESET_SHIFT, }; +struct omap_dss_dispc_dev_attr omap2_3_dss_dispc_dev_attr = { + .manager_count = 2, + .has_framedonetv_irq = 0 +}; diff --git a/arch/arm/mach-omap2/omap_hwmod_common_data.h b/arch/arm/mach-omap2/omap_hwmod_common_data.h index 39a7c37f458..ad5d8f04c0b 100644 --- a/arch/arm/mach-omap2/omap_hwmod_common_data.h +++ b/arch/arm/mach-omap2/omap_hwmod_common_data.h @@ -16,6 +16,8 @@ #include <plat/omap_hwmod.h> +#include "display.h" + /* Common address space across OMAP2xxx */ extern struct omap_hwmod_addr_space omap2xxx_uart1_addr_space[]; extern struct omap_hwmod_addr_space omap2xxx_uart2_addr_space[]; @@ -111,4 +113,6 @@ extern struct omap_hwmod_class omap2xxx_dma_hwmod_class; extern struct omap_hwmod_class omap2xxx_mailbox_hwmod_class; extern struct omap_hwmod_class omap2xxx_mcspi_class; +extern struct omap_dss_dispc_dev_attr omap2_3_dss_dispc_dev_attr; + #endif diff --git a/arch/arm/mach-omap2/omap_l3_noc.c b/arch/arm/mach-omap2/omap_l3_noc.c index c8b1bef92e5..d15225ff5c4 100644 --- a/arch/arm/mach-omap2/omap_l3_noc.c +++ b/arch/arm/mach-omap2/omap_l3_noc.c @@ -20,6 +20,7 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 * USA */ +#include <linux/module.h> #include <linux/init.h> #include <linux/io.h> #include <linux/platform_device.h> @@ -236,7 +237,7 @@ static int __devexit omap4_l3_remove(struct platform_device *pdev) static const struct of_device_id l3_noc_match[] = { {.compatible = "ti,omap4-l3-noc", }, {}, -} +}; MODULE_DEVICE_TABLE(of, l3_noc_match); #else #define l3_noc_match NULL diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 2ab7a9e17fe..00bff46ca48 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -14,6 +14,7 @@ #include <linux/io.h> #include <linux/err.h> #include <linux/opp.h> +#include <linux/export.h> #include <plat/omap-pm.h> #include <plat/omap_device.h> @@ -23,6 +24,7 @@ #include "powerdomain.h" #include "clockdomain.h" #include "pm.h" +#include "twl-common.h" static struct omap_device_pm_latency *pm_lats; @@ -225,11 +227,8 @@ postcore_initcall(omap2_common_pm_init); static int __init omap2_common_pm_late_init(void) { - /* Init the OMAP TWL parameters */ - omap3_twl_init(); - omap4_twl_init(); - /* Init the voltage layer */ + omap_pmic_late_init(); omap_voltage_late_init(); /* Initialize the voltages */ diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index c8cbd00a41a..efa66494c1e 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -99,31 +99,27 @@ static void omap3_enable_io_chain(void) { int timeout = 0; - if (omap_rev() >= OMAP3430_REV_ES3_1) { - omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, - PM_WKEN); - /* Do a readback to assure write has been done */ - omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN); - - while (!(omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN) & - OMAP3430_ST_IO_CHAIN_MASK)) { - timeout++; - if (timeout > 1000) { - printk(KERN_ERR "Wake up daisy chain " - "activation failed.\n"); - return; - } - omap2_prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK, - WKUP_MOD, PM_WKEN); + omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, + PM_WKEN); + /* Do a readback to assure write has been done */ + omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN); + + while (!(omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN) & + OMAP3430_ST_IO_CHAIN_MASK)) { + timeout++; + if (timeout > 1000) { + pr_err("Wake up daisy chain activation failed.\n"); + return; } + omap2_prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK, + WKUP_MOD, PM_WKEN); } } static void omap3_disable_io_chain(void) { - if (omap_rev() >= OMAP3430_REV_ES3_1) - omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, - PM_WKEN); + omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD, + PM_WKEN); } static void omap3_core_save_context(void) @@ -363,7 +359,6 @@ void omap_sram_idle(void) printk(KERN_ERR "Invalid mpu state in sram_idle\n"); return; } - pwrdm_pre_transition(); /* NEON control */ if (pwrdm_read_pwrst(neon_pwrdm) == PWRDM_POWER_ON) @@ -376,7 +371,8 @@ void omap_sram_idle(void) (per_next_state < PWRDM_POWER_ON || core_next_state < PWRDM_POWER_ON)) { omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN); - omap3_enable_io_chain(); + if (omap3_has_io_chain_ctrl()) + omap3_enable_io_chain(); } /* Block console output in case it is on one of the OMAP UARTs */ @@ -386,6 +382,8 @@ void omap_sram_idle(void) if (!console_trylock()) goto console_still_active; + pwrdm_pre_transition(); + /* PER */ if (per_next_state < PWRDM_POWER_ON) { per_going_off = (per_next_state == PWRDM_POWER_OFF) ? 1 : 0; @@ -409,13 +407,14 @@ void omap_sram_idle(void) omap3_intc_prepare_idle(); /* - * On EMU/HS devices ROM code restores a SRDC value - * from scratchpad which has automatic self refresh on timeout - * of AUTO_CNT = 1 enabled. This takes care of erratum ID i443. - * Hence store/restore the SDRC_POWER register here. - */ - if (omap_rev() >= OMAP3430_REV_ES3_0 && - omap_type() != OMAP2_DEVICE_TYPE_GP && + * On EMU/HS devices ROM code restores a SRDC value + * from scratchpad which has automatic self refresh on timeout + * of AUTO_CNT = 1 enabled. This takes care of erratum ID i443. + * Hence store/restore the SDRC_POWER register here. + */ + if (cpu_is_omap3430() && omap_rev() >= OMAP3430_REV_ES3_0 && + (omap_type() == OMAP2_DEVICE_TYPE_EMU || + omap_type() == OMAP2_DEVICE_TYPE_SEC) && core_next_state == PWRDM_POWER_OFF) sdrc_pwr = sdrc_read_reg(SDRC_POWER); @@ -432,8 +431,9 @@ void omap_sram_idle(void) omap34xx_do_sram_idle(save_state); /* Restore normal SDRC POWER settings */ - if (omap_rev() >= OMAP3430_REV_ES3_0 && - omap_type() != OMAP2_DEVICE_TYPE_GP && + if (cpu_is_omap3430() && omap_rev() >= OMAP3430_REV_ES3_0 && + (omap_type() == OMAP2_DEVICE_TYPE_EMU || + omap_type() == OMAP2_DEVICE_TYPE_SEC) && core_next_state == PWRDM_POWER_OFF) sdrc_write_reg(sdrc_pwr, SDRC_POWER); @@ -455,6 +455,8 @@ void omap_sram_idle(void) } omap3_intc_resume_idle(); + pwrdm_post_transition(); + /* PER */ if (per_next_state < PWRDM_POWER_ON) { per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm); @@ -475,11 +477,10 @@ console_still_active: core_next_state < PWRDM_POWER_ON)) { omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN); - omap3_disable_io_chain(); + if (omap3_has_io_chain_ctrl()) + omap3_disable_io_chain(); } - pwrdm_post_transition(); - clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]); } @@ -870,6 +871,9 @@ static int __init omap3_pm_init(void) if (!cpu_is_omap34xx()) return -ENODEV; + if (!omap3_has_io_chain_ctrl()) + pr_warning("PM: no software I/O chain control; some wakeups may be lost\n"); + pm_errata_configure(); /* XXX prcm_setup_regs needs to be before enabling hw diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index 5164d587ef5..8a18d1bd61c 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -1002,16 +1002,16 @@ int pwrdm_post_transition(void) * @pwrdm: struct powerdomain * to wait for * * Context loss count is the sum of powerdomain off-mode counter, the - * logic off counter and the per-bank memory off counter. Returns 0 + * logic off counter and the per-bank memory off counter. Returns negative * (and WARNs) upon error, otherwise, returns the context loss count. */ -u32 pwrdm_get_context_loss_count(struct powerdomain *pwrdm) +int pwrdm_get_context_loss_count(struct powerdomain *pwrdm) { int i, count; if (!pwrdm) { WARN(1, "powerdomain: %s: pwrdm is null\n", __func__); - return 0; + return -ENODEV; } count = pwrdm->state_counter[PWRDM_POWER_OFF]; @@ -1020,7 +1020,13 @@ u32 pwrdm_get_context_loss_count(struct powerdomain *pwrdm) for (i = 0; i < pwrdm->banks; i++) count += pwrdm->ret_mem_off_counter[i]; - pr_debug("powerdomain: %s: context loss count = %u\n", + /* + * Context loss count has to be a non-negative value. Clear the sign + * bit to get a value range from 0 to INT_MAX. + */ + count &= INT_MAX; + + pr_debug("powerdomain: %s: context loss count = %d\n", pwrdm->name, count); return count; diff --git a/arch/arm/mach-omap2/powerdomain.h b/arch/arm/mach-omap2/powerdomain.h index 42e6dd8f2a7..0d72a8a8ce4 100644 --- a/arch/arm/mach-omap2/powerdomain.h +++ b/arch/arm/mach-omap2/powerdomain.h @@ -217,7 +217,7 @@ int pwrdm_clkdm_state_switch(struct clockdomain *clkdm); int pwrdm_pre_transition(void); int pwrdm_post_transition(void); int pwrdm_set_lowpwrstchange(struct powerdomain *pwrdm); -u32 pwrdm_get_context_loss_count(struct powerdomain *pwrdm); +int pwrdm_get_context_loss_count(struct powerdomain *pwrdm); bool pwrdm_can_ever_lose_context(struct powerdomain *pwrdm); extern void omap242x_powerdomains_init(void); diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index 8db5f035eb0..597e2da831b 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -23,6 +23,7 @@ #include <linux/clk.h> #include <linux/io.h> #include <linux/delay.h> +#include <linux/export.h> #include <mach/system.h> #include <plat/common.h> diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c index 0347b93211e..cf246b39bac 100644 --- a/arch/arm/mach-omap2/smartreflex.c +++ b/arch/arm/mach-omap2/smartreflex.c @@ -17,6 +17,7 @@ * published by the Free Software Foundation. */ +#include <linux/module.h> #include <linux/interrupt.h> #include <linux/clk.h> #include <linux/io.h> @@ -138,7 +139,7 @@ static irqreturn_t sr_interrupt(int irq, void *data) sr_write_reg(sr_info, ERRCONFIG_V1, status); } else if (sr_info->ip_type == SR_TYPE_V2) { /* Read the status bits */ - sr_read_reg(sr_info, IRQSTATUS); + status = sr_read_reg(sr_info, IRQSTATUS); /* Clear them by writing back */ sr_write_reg(sr_info, IRQSTATUS, status); diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index e49fc7be222..037b0d7d4e0 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -408,14 +408,6 @@ static int omap2_dm_timer_set_src(struct platform_device *pdev, int source) return ret; } -struct omap_device_pm_latency omap2_dmtimer_latency[] = { - { - .deactivate_func = omap_device_idle_hwmods, - .activate_func = omap_device_enable_hwmods, - .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST, - }, -}; - /** * omap_timer_init - build and register timer device with an * associated timer hwmod @@ -477,9 +469,7 @@ static int __init omap_timer_init(struct omap_hwmod *oh, void *unused) pdata->get_context_loss_count = omap_pm_get_dev_context_loss_count; #endif pdev = omap_device_build(name, id, oh, pdata, sizeof(*pdata), - omap2_dmtimer_latency, - ARRAY_SIZE(omap2_dmtimer_latency), - 0); + NULL, 0, 0); if (IS_ERR(pdev)) { pr_err("%s: Can't build omap_device for %s: %s.\n", diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 52243577216..10b20c652e5 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -30,6 +30,7 @@ #include <plat/usb.h> #include "twl-common.h" +#include "pm.h" static struct i2c_board_info __initdata pmic_i2c_board_info = { .addr = 0x48, @@ -48,6 +49,16 @@ void __init omap_pmic_init(int bus, u32 clkrate, omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); } +void __init omap_pmic_late_init(void) +{ + /* Init the OMAP TWL parameters (if PMIC has been registerd) */ + if (!pmic_i2c_board_info.irq) + return; + + omap3_twl_init(); + omap4_twl_init(); +} + #if defined(CONFIG_ARCH_OMAP3) static struct twl4030_usb_data omap3_usb_pdata = { .usb_mode = T2_USB_MODE_ULPI, diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h index 5e83a5bd37f..275dde8cb27 100644 --- a/arch/arm/mach-omap2/twl-common.h +++ b/arch/arm/mach-omap2/twl-common.h @@ -1,6 +1,8 @@ #ifndef __OMAP_PMIC_COMMON__ #define __OMAP_PMIC_COMMON__ +#include <plat/irqs.h> + #define TWL_COMMON_PDATA_USB (1 << 0) #define TWL_COMMON_PDATA_BCI (1 << 1) #define TWL_COMMON_PDATA_MADC (1 << 2) @@ -30,6 +32,7 @@ struct twl4030_platform_data; void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq, struct twl4030_platform_data *pmic_data); +void omap_pmic_late_init(void); static inline void omap2_pmic_init(const char *pmic_type, struct twl4030_platform_data *pmic_data) diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index 47fb5d60763..267975086a7 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -60,44 +60,6 @@ static struct musb_hdrc_platform_data musb_plat = { static u64 musb_dmamask = DMA_BIT_MASK(32); -static void usb_musb_mux_init(struct omap_musb_board_data *board_data) -{ - switch (board_data->interface_type) { - case MUSB_INTERFACE_UTMI: - omap_mux_init_signal("usba0_otg_dp", OMAP_PIN_INPUT); - omap_mux_init_signal("usba0_otg_dm", OMAP_PIN_INPUT); - break; - case MUSB_INTERFACE_ULPI: - omap_mux_init_signal("usba0_ulpiphy_clk", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_stp", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dir", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_nxt", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat0", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat1", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat2", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat3", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat4", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat5", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat6", - OMAP_PIN_INPUT_PULLDOWN); - omap_mux_init_signal("usba0_ulpiphy_dat7", - OMAP_PIN_INPUT_PULLDOWN); - break; - default: - break; - } -} - static struct omap_musb_board_data musb_default_board_data = { .interface_type = MUSB_INTERFACE_ULPI, .mode = MUSB_OTG, diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index 8dd26b765b7..994d8f591a1 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -8,11 +8,13 @@ * published by the Free Software Foundation. */ +#include <linux/string.h> #include <linux/types.h> #include <linux/errno.h> #include <linux/delay.h> #include <linux/platform_device.h> #include <linux/gpio.h> +#include <linux/export.h> #include <linux/usb/musb.h> diff --git a/arch/arm/mach-omap2/voltage.c b/arch/arm/mach-omap2/voltage.c index 64070ac1e76..1f8fdf736e6 100644 --- a/arch/arm/mach-omap2/voltage.c +++ b/arch/arm/mach-omap2/voltage.c @@ -22,6 +22,7 @@ #include <linux/delay.h> #include <linux/io.h> #include <linux/err.h> +#include <linux/export.h> #include <linux/debugfs.h> #include <linux/slab.h> #include <linux/clk.h> |