diff options
Diffstat (limited to 'arch/arm/mach-pxa/include/mach/pxafb.h')
| -rw-r--r-- | arch/arm/mach-pxa/include/mach/pxafb.h | 153 |
1 files changed, 153 insertions, 0 deletions
diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h new file mode 100644 index 00000000000..8e591118371 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -0,0 +1,153 @@ +/* + * arch/arm/mach-pxa/include/mach/pxafb.h + * + * Support for the xscale frame buffer. + * + * Author: Jean-Frederic Clere + * Created: Sep 22, 2003 + * Copyright: jfclere@sinix.net + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/fb.h> +#include <mach/regs-lcd.h> + +/* + * Supported LCD connections + * + * bits 0 - 3: for LCD panel type: + * + * STN - for passive matrix + * DSTN - for dual scan passive matrix + * TFT - for active matrix + * + * bits 4 - 9 : for bus width + * bits 10-17 : for AC Bias Pin Frequency + * bit 18 : for output enable polarity + * bit 19 : for pixel clock edge + * bit 20 : for output pixel format when base is RGBT16 + */ +#define LCD_CONN_TYPE(_x) ((_x) & 0x0f) +#define LCD_CONN_WIDTH(_x) (((_x) >> 4) & 0x1f) + +#define LCD_TYPE_UNKNOWN 0 +#define LCD_TYPE_MONO_STN 1 +#define LCD_TYPE_MONO_DSTN 2 +#define LCD_TYPE_COLOR_STN 3 +#define LCD_TYPE_COLOR_DSTN 4 +#define LCD_TYPE_COLOR_TFT 5 +#define LCD_TYPE_SMART_PANEL 6 +#define LCD_TYPE_MAX 7 + +#define LCD_MONO_STN_4BPP ((4 << 4) | LCD_TYPE_MONO_STN) +#define LCD_MONO_STN_8BPP ((8 << 4) | LCD_TYPE_MONO_STN) +#define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN) +#define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN) +#define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN) +#define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT) +#define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT) +#define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL) +#define LCD_SMART_PANEL_16BPP ((16 << 4) | LCD_TYPE_SMART_PANEL) +#define LCD_SMART_PANEL_18BPP ((18 << 4) | LCD_TYPE_SMART_PANEL) + +#define LCD_AC_BIAS_FREQ(x) (((x) & 0xff) << 10) +#define LCD_BIAS_ACTIVE_HIGH (0 << 18) +#define LCD_BIAS_ACTIVE_LOW (1 << 18) +#define LCD_PCLK_EDGE_RISE (0 << 19) +#define LCD_PCLK_EDGE_FALL (1 << 19) +#define LCD_ALTERNATE_MAPPING (1 << 20) + +/* + * This structure describes the machine which we are running on. + * It is set in linux/arch/arm/mach-pxa/machine_name.c and used in the probe routine + * of linux/drivers/video/pxafb.c + */ +struct pxafb_mode_info { + u_long pixclock; + + u_short xres; + u_short yres; + + u_char bpp; + u_int cmap_greyscale:1, + depth:8, + unused:23; + + /* Parallel Mode Timing */ + u_char hsync_len; + u_char left_margin; + u_char right_margin; + + u_char vsync_len; + u_char upper_margin; + u_char lower_margin; + u_char sync; + + /* Smart Panel Mode Timing - see PXA27x DM 7.4.15.0.3 for details + * Note: + * 1. all parameters in nanosecond (ns) + * 2. a0cs{rd,wr}_set_hld are controlled by the same register bits + * in pxa27x and pxa3xx, initialize them to the same value or + * the larger one will be used + * 3. same to {rd,wr}_pulse_width + */ + unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */ + unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */ + unsigned wr_pulse_width; /* L_PCLK_WR pulse width */ + unsigned rd_pulse_width; /* L_FCLK_RD pulse width */ + unsigned cmd_inh_time; /* Command Inhibit time between two writes */ + unsigned op_hold_time; /* Output Hold time from L_FCLK_RD negation */ +}; + +struct pxafb_mach_info { + struct pxafb_mode_info *modes; + unsigned int num_modes; + + unsigned int lcd_conn; + + u_int fixed_modes:1, + cmap_inverse:1, + cmap_static:1, + unused:29; + + /* The following should be defined in LCCR0 + * LCCR0_Act or LCCR0_Pas Active or Passive + * LCCR0_Sngl or LCCR0_Dual Single/Dual panel + * LCCR0_Mono or LCCR0_Color Mono/Color + * LCCR0_4PixMono or LCCR0_8PixMono (in mono single mode) + * LCCR0_DMADel(Tcpu) (optional) DMA request delay + * + * The following should not be defined in LCCR0: + * LCCR0_OUM, LCCR0_BM, LCCR0_QDM, LCCR0_DIS, LCCR0_EFM + * LCCR0_IUM, LCCR0_SFM, LCCR0_LDM, LCCR0_ENB + */ + u_int lccr0; + /* The following should be defined in LCCR3 + * LCCR3_OutEnH or LCCR3_OutEnL Output enable polarity + * LCCR3_PixRsEdg or LCCR3_PixFlEdg Pixel clock edge type + * LCCR3_Acb(X) AB Bias pin frequency + * LCCR3_DPC (optional) Double Pixel Clock mode (untested) + * + * The following should not be defined in LCCR3 + * LCCR3_HSP, LCCR3_VSP, LCCR0_Pcd(x), LCCR3_Bpp + */ + u_int lccr3; + /* The following should be defined in LCCR4 + * LCCR4_PAL_FOR_0 or LCCR4_PAL_FOR_1 or LCCR4_PAL_FOR_2 + * + * All other bits in LCCR4 should be left alone. + */ + u_int lccr4; + void (*pxafb_backlight_power)(int); + void (*pxafb_lcd_power)(int, struct fb_var_screeninfo *); + void (*smart_update)(struct fb_info *); +}; +void set_pxa_fb_info(struct pxafb_mach_info *hard_pxa_fb_info); +void set_pxa_fb_parent(struct device *parent_dev); +unsigned long pxafb_get_hsync_time(struct device *dev); + +extern int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int); +extern int pxafb_smart_flush(struct fb_info *info); |