diff options
Diffstat (limited to 'arch/arm/mach-pxa')
54 files changed, 2506 insertions, 609 deletions
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index dee92182749..38fbd0a0e40 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -115,6 +115,11 @@ config MACH_CM_X300 select CPU_PXA310 select HAVE_PWM +config MACH_CAPC7117 + bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM" + select CPU_PXA320 + select PXA3xx + config ARCH_GUMSTIX bool "Gumstix XScale 255 boards" select PXA25x @@ -417,6 +422,24 @@ config MACH_TREO680 Say Y here if you intend to run this kernel on Palm Treo 680 smartphone. +config MACH_RAUMFELD_RC + bool "Raumfeld Controller" + select PXA3xx + select CPU_PXA300 + select HAVE_PWM + +config MACH_RAUMFELD_CONNECTOR + bool "Raumfeld Connector" + select PXA3xx + select CPU_PXA300 + select PXA_SSP + +config MACH_RAUMFELD_SPEAKER + bool "Raumfeld Speaker" + select PXA3xx + select CPU_PXA300 + select PXA_SSP + config PXA_SHARPSL bool "SHARP Zaurus SL-5600, SL-C7xx and SL-Cxx00 Models" select SHARP_SCOOP @@ -435,6 +458,7 @@ config SHARPSL_PM config CORGI_SSP_DEPRECATED bool select PXA_SSP + select PXA_SSP_LEGACY help This option will include corgi_ssp.c and corgi_lcd.c that corgi_ts.c and other legacy drivers (corgi_bl.c @@ -446,6 +470,7 @@ config MACH_POODLE select PXA25x select SHARP_LOCOMO select PXA_SSP + select PXA_HAVE_BOARD_IRQS config MACH_CORGI bool "Enable Sharp SL-C700 (Corgi) Support" @@ -492,6 +517,11 @@ config MACH_TOSA select PXA25x select PXA_HAVE_BOARD_IRQS +config MACH_ICONTROL + bool "TMT iControl/SafeTCam based on the MXM-8x10 CoM" + select CPU_PXA320 + select PXA3xx + config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x @@ -629,6 +659,11 @@ config PXA_SSP help Enable support for PXA2xx SSP ports +config PXA_SSP_LEGACY + bool + help + Support of legacy SSP API + config TOSA_BT tristate "Control the state of built-in bluetooth chip on Sharp SL-6000" depends on MACH_TOSA diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index f64afda7e6f..86bc87b7f2d 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -48,6 +48,7 @@ obj-$(CONFIG_MACH_ARMCORE) += cm-x2xx-pci.o endif obj-$(CONFIG_MACH_EM_X270) += em-x270.o obj-$(CONFIG_MACH_CM_X300) += cm-x300.o +obj-$(CONFIG_MACH_CAPC7117) += capc7117.o mxm8x10.o obj-$(CONFIG_ARCH_GUMSTIX) += gumstix.o obj-$(CONFIG_GUMSTIX_AM200EPD) += am200epd.o obj-$(CONFIG_GUMSTIX_AM300EPD) += am300epd.o @@ -82,6 +83,7 @@ obj-$(CONFIG_PXA_SHARP_Cxx00) += spitz.o sharpsl_pm.o spitz_pm.o obj-$(CONFIG_CORGI_SSP_DEPRECATED) += corgi_ssp.o corgi_lcd.o obj-$(CONFIG_MACH_POODLE) += poodle.o obj-$(CONFIG_MACH_TOSA) += tosa.o +obj-$(CONFIG_MACH_ICONTROL) += icontrol.o mxm8x10.o obj-$(CONFIG_ARCH_PXA_ESERIES) += eseries.o obj-$(CONFIG_MACH_E330) += e330.o obj-$(CONFIG_MACH_E350) += e350.o @@ -89,6 +91,9 @@ obj-$(CONFIG_MACH_E740) += e740.o obj-$(CONFIG_MACH_E750) += e750.o obj-$(CONFIG_MACH_E400) += e400.o obj-$(CONFIG_MACH_E800) += e800.o +obj-$(CONFIG_MACH_RAUMFELD_RC) += raumfeld.o +obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR) += raumfeld.o +obj-$(CONFIG_MACH_RAUMFELD_SPEAKER) += raumfeld.o # Support for blinky lights led-y := leds.o diff --git a/arch/arm/mach-pxa/am300epd.c b/arch/arm/mach-pxa/am300epd.c index 4bd10a17332..993d75e6639 100644 --- a/arch/arm/mach-pxa/am300epd.c +++ b/arch/arm/mach-pxa/am300epd.c @@ -288,7 +288,7 @@ int __init am300_init(void) } module_param(panel_type, uint, 0); -MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97"); +MODULE_PARM_DESC(panel_type, "Select the panel type: 37, 6, 97"); MODULE_DESCRIPTION("board driver for am300 epd kit"); MODULE_AUTHOR("Jaya Kumar"); diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c index b8cd07ca938..f3b5ace815e 100644 --- a/arch/arm/mach-pxa/balloon3.c +++ b/arch/arm/mach-pxa/balloon3.c @@ -132,6 +132,14 @@ static void __init balloon3_init_irq(void) "enabled\n", __func__, BALLOON3_AUX_NIRQ); } +static unsigned long balloon3_ac97_pin_config[] = { + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + GPIO113_AC97_nRESET, +}; + static void balloon3_backlight_power(int on) { pr_debug("%s: power is %s\n", __func__, on ? "on" : "off"); @@ -140,26 +148,7 @@ static void balloon3_backlight_power(int on) static unsigned long balloon3_lcd_pin_config[] = { /* LCD - 16bpp Active TFT */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, GPIO99_GPIO, /* Backlight */ }; @@ -311,8 +300,10 @@ static void __init balloon3_init(void) pxa_set_stuart_info(NULL); pxa_set_i2c_info(NULL); - if (balloon3_has(BALLOON3_FEATURE_AUDIO)) + if (balloon3_has(BALLOON3_FEATURE_AUDIO)) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ac97_pin_config)); pxa_set_ac97_info(NULL); + } if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) { pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config)); diff --git a/arch/arm/mach-pxa/capc7117.c b/arch/arm/mach-pxa/capc7117.c new file mode 100644 index 00000000000..aae544631a8 --- /dev/null +++ b/arch/arm/mach-pxa/capc7117.c @@ -0,0 +1,158 @@ +/* + * linux/arch/arm/mach-pxa/capc7117.c + * + * Support for the Embedian CAPC-7117 Evaluation Kit + * based on the Embedian MXM-8x10 Computer on Module + * + * Copyright (C) 2009 Embedian Inc. + * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd. + * + * 2007-09-04: eric miao <eric.y.miao@gmail.com> + * rewrite to align with latest kernel + * + * 2010-01-09: Edwin Peer <epeer@tmtservices.co.za> + * Hennie van der Merwe <hvdmerwe@tmtservices.co.za> + * rework for upstream merge + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/irq.h> +#include <linux/platform_device.h> +#include <linux/ata_platform.h> +#include <linux/serial_8250.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/pxa320.h> +#include <mach/mxm8x10.h> + +#include "generic.h" + +/* IDE (PATA) Support */ +static struct pata_platform_info pata_platform_data = { + .ioport_shift = 1 +}; + +static struct resource capc7117_ide_resources[] = { + [0] = { + .start = 0x11000020, + .end = 0x1100003f, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = 0x1100001c, + .end = 0x1100001c, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76)), + .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO76)), + .flags = IORESOURCE_IRQ | IRQF_TRIGGER_RISING + } +}; + +static struct platform_device capc7117_ide_device = { + .name = "pata_platform", + .num_resources = ARRAY_SIZE(capc7117_ide_resources), + .resource = capc7117_ide_resources, + .dev = { + .platform_data = &pata_platform_data, + .coherent_dma_mask = ~0 /* grumble */ + } +}; + +static void __init capc7117_ide_init(void) +{ + platform_device_register(&capc7117_ide_device); +} + +/* TI16C752 UART support */ +#define TI16C752_FLAGS (UPF_BOOT_AUTOCONF | \ + UPF_IOREMAP | \ + UPF_BUGGY_UART | \ + UPF_SKIP_TEST) +#define TI16C752_UARTCLK (22118400) +static struct plat_serial8250_port ti16c752_platform_data[] = { + [0] = { + .mapbase = 0x14000000, + .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO78)), + .irqflags = IRQF_TRIGGER_RISING, + .flags = TI16C752_FLAGS, + .iotype = UPIO_MEM, + .regshift = 1, + .uartclk = TI16C752_UARTCLK + }, + [1] = { + .mapbase = 0x14000040, + .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO79)), + .irqflags = IRQF_TRIGGER_RISING, + .flags = TI16C752_FLAGS, + .iotype = UPIO_MEM, + .regshift = 1, + .uartclk = TI16C752_UARTCLK + }, + [2] = { + .mapbase = 0x14000080, + .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO80)), + .irqflags = IRQF_TRIGGER_RISING, + .flags = TI16C752_FLAGS, + .iotype = UPIO_MEM, + .regshift = 1, + .uartclk = TI16C752_UARTCLK + }, + [3] = { + .mapbase = 0x140000c0, + .irq = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO81)), + .irqflags = IRQF_TRIGGER_RISING, + .flags = TI16C752_FLAGS, + .iotype = UPIO_MEM, + .regshift = 1, + .uartclk = TI16C752_UARTCLK + }, + [4] = { + /* end of array */ + } +}; + +static struct platform_device ti16c752_device = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = ti16c752_platform_data + } +}; + +static void __init capc7117_uarts_init(void) +{ + platform_device_register(&ti16c752_device); +} + +static void __init capc7117_init(void) +{ + /* Init CoM */ + mxm_8x10_barebones_init(); + + /* Init evaluation board peripherals */ + mxm_8x10_ac97_init(); + mxm_8x10_usb_host_init(); + mxm_8x10_mmc_init(); + + capc7117_uarts_init(); + capc7117_ide_init(); +} + +MACHINE_START(CAPC7117, + "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM") + .phys_io = 0x40000000, + .boot_params = 0xa0000100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, + .init_machine = capc7117_init +MACHINE_END diff --git a/arch/arm/mach-pxa/cm-x255.c b/arch/arm/mach-pxa/cm-x255.c index 253fd76142d..f1a7703d771 100644 --- a/arch/arm/mach-pxa/cm-x255.c +++ b/arch/arm/mach-pxa/cm-x255.c @@ -50,26 +50,7 @@ static unsigned long cmx255_pin_config[] = { GPIO47_STUART_TXD, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* SSP1 */ GPIO23_SSP1_SCLK, diff --git a/arch/arm/mach-pxa/cm-x270.c b/arch/arm/mach-pxa/cm-x270.c index eea78b6c2bc..a9926bb7592 100644 --- a/arch/arm/mach-pxa/cm-x270.c +++ b/arch/arm/mach-pxa/cm-x270.c @@ -71,26 +71,7 @@ static unsigned long cmx270_pin_config[] = { GPIO111_MMC_DAT_3, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* I2C */ GPIO117_I2C_SCL, @@ -195,33 +176,57 @@ static struct resource cmx270_2700G_resource[] = { }, }; -static unsigned long save_lcd_regs[10]; +static unsigned long cmx270_marathon_on[] = { + GPIO58_GPIO, + GPIO59_GPIO, + GPIO60_GPIO, + GPIO61_GPIO, + GPIO62_GPIO, + GPIO63_GPIO, + GPIO64_GPIO, + GPIO65_GPIO, + GPIO66_GPIO, + GPIO67_GPIO, + GPIO68_GPIO, + GPIO69_GPIO, + GPIO70_GPIO, + GPIO71_GPIO, + GPIO72_GPIO, + GPIO73_GPIO, + GPIO74_GPIO, + GPIO75_GPIO, + GPIO76_GPIO, + GPIO77_GPIO, +}; + +static unsigned long cmx270_marathon_off[] = { + GPIOxx_LCD_TFT_16BPP, +}; static int cmx270_marathon_probe(struct fb_info *fb) { - /* save PXA-270 pin settings before enabling 2700G */ - save_lcd_regs[0] = GPDR1; - save_lcd_regs[1] = GPDR2; - save_lcd_regs[2] = GAFR1_U; - save_lcd_regs[3] = GAFR2_L; - save_lcd_regs[4] = GAFR2_U; - - /* Disable PXA-270 on-chip controller driving pins */ - GPDR1 &= ~(0xfc000000); - GPDR2 &= ~(0x00c03fff); - GAFR1_U &= ~(0xfff00000); - GAFR2_L &= ~(0x0fffffff); - GAFR2_U &= ~(0x0000f000); + int gpio, err; + + for (gpio = 58; gpio <= 77; gpio++) { + err = gpio_request(gpio, "LCD"); + if (err) + return err; + gpio_direction_input(gpio); + } + + pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_on)); return 0; } static int cmx270_marathon_remove(struct fb_info *fb) { - GPDR1 = save_lcd_regs[0]; - GPDR2 = save_lcd_regs[1]; - GAFR1_U = save_lcd_regs[2]; - GAFR2_L = save_lcd_regs[3]; - GAFR2_U = save_lcd_regs[4]; + int gpio; + + pxa2xx_mfp_config(ARRAY_AND_SIZE(cmx270_marathon_off)); + + for (gpio = 58; gpio <= 77; gpio++) + gpio_free(gpio); + return 0; } diff --git a/arch/arm/mach-pxa/cm-x2xx-pci.c b/arch/arm/mach-pxa/cm-x2xx-pci.c index 7873fa3d8fa..161fc2d6120 100644 --- a/arch/arm/mach-pxa/cm-x2xx-pci.c +++ b/arch/arm/mach-pxa/cm-x2xx-pci.c @@ -59,7 +59,7 @@ void __init cmx2xx_pci_adjust_zones(int node, unsigned long *zone_size, static void cmx2xx_it8152_irq_demux(unsigned int irq, struct irq_desc *desc) { /* clear our parent irq */ - GEDR(cmx2xx_it8152_irq_gpio) = GPIO_bit(cmx2xx_it8152_irq_gpio); + desc->chip->ack(irq); it8152_irq_demux(irq, desc); } diff --git a/arch/arm/mach-pxa/corgi_ssp.c b/arch/arm/mach-pxa/corgi_ssp.c index a5ee70735e0..1d9bc118ee3 100644 --- a/arch/arm/mach-pxa/corgi_ssp.c +++ b/arch/arm/mach-pxa/corgi_ssp.c @@ -204,7 +204,7 @@ void __init corgi_ssp_set_machinfo(struct corgissp_machinfo *machinfo) ssp_machinfo = machinfo; } -static int __init corgi_ssp_probe(struct platform_device *dev) +static int __devinit corgi_ssp_probe(struct platform_device *dev) { int ret; diff --git a/arch/arm/mach-pxa/e740.c b/arch/arm/mach-pxa/e740.c index 94b23a9e387..d578021d1a1 100644 --- a/arch/arm/mach-pxa/e740.c +++ b/arch/arm/mach-pxa/e740.c @@ -134,6 +134,12 @@ static unsigned long e740_pin_config[] __initdata = { /* IrDA */ GPIO38_GPIO | MFP_LPM_DRIVE_HIGH, + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + /* Audio power control */ GPIO16_GPIO, /* AC97 codec AVDD2 supply (analogue power) */ GPIO40_GPIO, /* Mic amp power */ diff --git a/arch/arm/mach-pxa/e750.c b/arch/arm/mach-pxa/e750.c index 5eccbce73a3..af83caa52dd 100644 --- a/arch/arm/mach-pxa/e750.c +++ b/arch/arm/mach-pxa/e750.c @@ -132,6 +132,12 @@ static unsigned long e750_pin_config[] __initdata = { /* IrDA */ GPIO38_GPIO | MFP_LPM_DRIVE_HIGH, + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + /* Audio power control */ GPIO4_GPIO, /* Headphone amp power */ GPIO7_GPIO, /* Speaker amp power */ diff --git a/arch/arm/mach-pxa/e800.c b/arch/arm/mach-pxa/e800.c index aad129bed19..8ea97bf53fe 100644 --- a/arch/arm/mach-pxa/e800.c +++ b/arch/arm/mach-pxa/e800.c @@ -35,6 +35,14 @@ /* ------------------------ e800 LCD definitions ------------------------- */ +static unsigned long e800_pin_config[] __initdata = { + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, +}; + static struct w100_gen_regs e800_lcd_regs = { .lcd_format = 0x00008003, .lcdd_cntl1 = 0x02a00000, @@ -195,6 +203,7 @@ static struct platform_device *devices[] __initdata = { static void __init e800_init(void) { + pxa2xx_mfp_config(ARRAY_AND_SIZE(e800_pin_config)); pxa_set_ffuart_info(NULL); pxa_set_btuart_info(NULL); pxa_set_stuart_info(NULL); diff --git a/arch/arm/mach-pxa/em-x270.c b/arch/arm/mach-pxa/em-x270.c index c8a01bc85fd..aab04f33e49 100644 --- a/arch/arm/mach-pxa/em-x270.c +++ b/arch/arm/mach-pxa/em-x270.c @@ -109,26 +109,7 @@ static unsigned long common_pin_config[] = { GPIO111_MMC_DAT_3, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* QCI */ GPIO84_CIF_FV, diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c new file mode 100644 index 00000000000..771137fc1a8 --- /dev/null +++ b/arch/arm/mach-pxa/icontrol.c @@ -0,0 +1,202 @@ +/* + * linux/arch/arm/mach-pxa/icontrol.c + * + * Support for the iControl and SafeTcam platforms from TMT Services + * using the Embedian MXM-8x10 Computer on Module + * + * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd. + * + * 2010-01-21 Hennie van der Merve <hvdmerwe@tmtservies.co.za> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/irq.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/pxa320.h> +#include <mach/mxm8x10.h> + +#include <linux/spi/spi.h> +#include <mach/pxa2xx_spi.h> +#include <linux/can/platform/mcp251x.h> + +#include "generic.h" + +#define ICONTROL_MCP251x_nCS1 (15) +#define ICONTROL_MCP251x_nCS2 (16) +#define ICONTROL_MCP251x_nCS3 (17) +#define ICONTROL_MCP251x_nCS4 (24) + +#define ICONTROL_MCP251x_nIRQ1 (74) +#define ICONTROL_MCP251x_nIRQ2 (75) +#define ICONTROL_MCP251x_nIRQ3 (76) +#define ICONTROL_MCP251x_nIRQ4 (77) + +static struct pxa2xx_spi_chip mcp251x_chip_info1 = { + .tx_threshold = 8, + .rx_threshold = 128, + .dma_burst_size = 8, + .timeout = 235, + .gpio_cs = ICONTROL_MCP251x_nCS1 +}; + +static struct pxa2xx_spi_chip mcp251x_chip_info2 = { + .tx_threshold = 8, + .rx_threshold = 128, + .dma_burst_size = 8, + .timeout = 235, + .gpio_cs = ICONTROL_MCP251x_nCS2 +}; + +static struct pxa2xx_spi_chip mcp251x_chip_info3 = { + .tx_threshold = 8, + .rx_threshold = 128, + .dma_burst_size = 8, + .timeout = 235, + .gpio_cs = ICONTROL_MCP251x_nCS3 +}; + +static struct pxa2xx_spi_chip mcp251x_chip_info4 = { + .tx_threshold = 8, + .rx_threshold = 128, + .dma_burst_size = 8, + .timeout = 235, + .gpio_cs = ICONTROL_MCP251x_nCS4 +}; + +static struct mcp251x_platform_data mcp251x_info = { + .oscillator_frequency = 16E6, + .model = CAN_MCP251X_MCP2515, + .board_specific_setup = NULL, + .power_enable = NULL, + .transceiver_enable = NULL +}; + +static struct spi_board_info mcp251x_board_info[] = { + { + .modalias = "mcp251x", + .max_speed_hz = 6500000, + .bus_num = 3, + .chip_select = 0, + .platform_data = &mcp251x_info, + .controller_data = &mcp251x_chip_info1, + .irq = gpio_to_irq(ICONTROL_MCP251x_nIRQ1) + }, + { + .modalias = "mcp251x", + .max_speed_hz = 6500000, + .bus_num = 3, + .chip_select = 1, + .platform_data = &mcp251x_info, + .controller_data = &mcp251x_chip_info2, + .irq = gpio_to_irq(ICONTROL_MCP251x_nIRQ2) + }, + { + .modalias = "mcp251x", + .max_speed_hz = 6500000, + .bus_num = 4, + .chip_select = 0, + .platform_data = &mcp251x_info, + .controller_data = &mcp251x_chip_info3, + .irq = gpio_to_irq(ICONTROL_MCP251x_nIRQ3) + }, + { + .modalias = "mcp251x", + .max_speed_hz = 6500000, + .bus_num = 4, + .chip_select = 1, + .platform_data = &mcp251x_info, + .controller_data = &mcp251x_chip_info4, + .irq = gpio_to_irq(ICONTROL_MCP251x_nIRQ4) + } +}; + +static struct pxa2xx_spi_master pxa_ssp3_spi_master_info = { + .clock_enable = CKEN_SSP3, + .num_chipselect = 2, + .enable_dma = 1 +}; + +static struct pxa2xx_spi_master pxa_ssp4_spi_master_info = { + .clock_enable = CKEN_SSP4, + .num_chipselect = 2, + .enable_dma = 1 +}; + +struct platform_device pxa_spi_ssp3 = { + .name = "pxa2xx-spi", + .id = 3, + .dev = { + .platform_data = &pxa_ssp3_spi_master_info, + } +}; + +struct platform_device pxa_spi_ssp4 = { + .name = "pxa2xx-spi", + .id = 4, + .dev = { + .platform_data = &pxa_ssp4_spi_master_info, + } +}; + +static struct platform_device *icontrol_spi_devices[] __initdata = { + &pxa_spi_ssp3, + &pxa_spi_ssp4, +}; + +static mfp_cfg_t mfp_can_cfg[] __initdata = { + /* CAN CS lines */ + GPIO15_GPIO, + GPIO16_GPIO, + GPIO17_GPIO, + GPIO24_GPIO, + + /* SPI (SSP3) lines */ + GPIO89_SSP3_SCLK, + GPIO91_SSP3_TXD, + GPIO92_SSP3_RXD, + + /* SPI (SSP4) lines */ + GPIO93_SSP4_SCLK, + GPIO95_SSP4_TXD, + GPIO96_SSP4_RXD, + + /* CAN nIRQ lines */ + GPIO74_GPIO | MFP_LPM_EDGE_RISE, + GPIO75_GPIO | MFP_LPM_EDGE_RISE, + GPIO76_GPIO | MFP_LPM_EDGE_RISE, + GPIO77_GPIO | MFP_LPM_EDGE_RISE +}; + +static void __init icontrol_can_init(void) +{ + pxa3xx_mfp_config(ARRAY_AND_SIZE(mfp_can_cfg)); + platform_add_devices(ARRAY_AND_SIZE(icontrol_spi_devices)); + spi_register_board_info(ARRAY_AND_SIZE(mcp251x_board_info)); +} + +static void __init icontrol_init(void) +{ + mxm_8x10_barebones_init(); + mxm_8x10_usb_host_init(); + mxm_8x10_mmc_init(); + + icontrol_can_init(); +} + +MACHINE_START(ICONTROL, "iControl/SafeTcam boards using Embedian MXM-8x10 CoM") + .phys_io = 0x40000000, + .boot_params = 0xa0000100, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, + .init_machine = icontrol_init +MACHINE_END diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c index 5c9e11d74f4..bc78c4dc0c6 100644 --- a/arch/arm/mach-pxa/idp.c +++ b/arch/arm/mach-pxa/idp.c @@ -47,25 +47,7 @@ static unsigned long idp_pin_config[] __initdata = { /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, + GPIOxx_LCD_DSTN_16BPP, /* BTUART */ GPIO42_BTUART_RXD, diff --git a/arch/arm/mach-pxa/imote2.c b/arch/arm/mach-pxa/imote2.c index 5b0862df61a..b2f878bd460 100644 --- a/arch/arm/mach-pxa/imote2.c +++ b/arch/arm/mach-pxa/imote2.c @@ -64,7 +64,6 @@ static unsigned long imote2_pin_config[] __initdata = { GPIO116_GPIO, /* CC_CCA */ GPIO0_GPIO, /* CC_FIFOP */ GPIO16_GPIO, /* CCSFD */ - GPIO39_GPIO, /* CSn */ GPIO115_GPIO, /* Power enable */ /* I2C */ @@ -72,7 +71,7 @@ static unsigned long imote2_pin_config[] __initdata = { GPIO118_I2C_SDA, /* SSP 3 - 802.15.4 radio */ - GPIO39_GPIO, /* Chip Select */ + GPIO39_GPIO, /* Chip Select */ GPIO34_SSP3_SCLK, GPIO35_SSP3_TXD, GPIO41_SSP3_RXD, diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h index bfec09b1814..1a741065045 100644 --- a/arch/arm/mach-pxa/include/mach/balloon3.h +++ b/arch/arm/mach-pxa/include/mach/balloon3.h @@ -129,6 +129,16 @@ enum balloon3_features { #define CPLD_AROUTING_LOONR2INT_BIT 6 #define CPLD_AROUTING_LOONR2EXT_BIT 7 +/* Balloon3 Interrupts */ +#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x)) + +#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0) +#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1) + +#define BALLOON3_AUX_NIRQ IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ) +#define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ) +#define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD) + extern int balloon3_has(enum balloon3_features feature); #endif diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index e741bf1bfb2..7515757d691 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -314,7 +314,6 @@ extern unsigned long get_clock_tick_rate(void); #define PCIBIOS_MIN_IO 0 #define PCIBIOS_MIN_MEM 0 #define pcibios_assign_all_busses() 1 -#define HAVE_ARCH_PCI_SET_DMA_MASK 1 #endif diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h index 3677a9af9c8..ffc8314520f 100644 --- a/arch/arm/mach-pxa/include/mach/irqs.h +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -135,82 +135,6 @@ #define IRQ_BOARD_END (IRQ_BOARD_START + 16) #endif -#define IRQ_SA1111_START (IRQ_BOARD_END) -#define IRQ_GPAIN0 (IRQ_BOARD_END + 0) -#define IRQ_GPAIN1 (IRQ_BOARD_END + 1) -#define IRQ_GPAIN2 (IRQ_BOARD_END + 2) -#define IRQ_GPAIN3 (IRQ_BOARD_END + 3) -#define IRQ_GPBIN0 (IRQ_BOARD_END + 4) -#define IRQ_GPBIN1 (IRQ_BOARD_END + 5) -#define IRQ_GPBIN2 (IRQ_BOARD_END + 6) -#define IRQ_GPBIN3 (IRQ_BOARD_END + 7) -#define IRQ_GPBIN4 (IRQ_BOARD_END + 8) -#define IRQ_GPBIN5 (IRQ_BOARD_END + 9) -#define IRQ_GPCIN0 (IRQ_BOARD_END + 10) -#define IRQ_GPCIN1 (IRQ_BOARD_END + 11) -#define IRQ_GPCIN2 (IRQ_BOARD_END + 12) -#define IRQ_GPCIN3 (IRQ_BOARD_END + 13) -#define IRQ_GPCIN4 (IRQ_BOARD_END + 14) -#define IRQ_GPCIN5 (IRQ_BOARD_END + 15) -#define IRQ_GPCIN6 (IRQ_BOARD_END + 16) -#define IRQ_GPCIN7 (IRQ_BOARD_END + 17) -#define IRQ_MSTXINT (IRQ_BOARD_END + 18) -#define IRQ_MSRXINT (IRQ_BOARD_END + 19) -#define IRQ_MSSTOPERRINT (IRQ_BOARD_END + 20) -#define IRQ_TPTXINT (IRQ_BOARD_END + 21) -#define IRQ_TPRXINT (IRQ_BOARD_END + 22) -#define IRQ_TPSTOPERRINT (IRQ_BOARD_END + 23) -#define SSPXMTINT (IRQ_BOARD_END + 24) -#define SSPRCVINT (IRQ_BOARD_END + 25) -#define SSPROR (IRQ_BOARD_END + 26) -#define AUDXMTDMADONEA (IRQ_BOARD_END + 32) -#define AUDRCVDMADONEA (IRQ_BOARD_END + 33) -#define AUDXMTDMADONEB (IRQ_BOARD_END + 34) -#define AUDRCVDMADONEB (IRQ_BOARD_END + 35) -#define AUDTFSR (IRQ_BOARD_END + 36) -#define AUDRFSR (IRQ_BOARD_END + 37) -#define AUDTUR (IRQ_BOARD_END + 38) -#define AUDROR (IRQ_BOARD_END + 39) -#define AUDDTS (IRQ_BOARD_END + 40) -#define AUDRDD (IRQ_BOARD_END + 41) -#define AUDSTO (IRQ_BOARD_END + 42) -#define IRQ_USBPWR (IRQ_BOARD_END + 43) -#define IRQ_HCIM (IRQ_BOARD_END + 44) -#define IRQ_HCIBUFFACC (IRQ_BOARD_END + 45) -#define IRQ_HCIRMTWKP (IRQ_BOARD_END + 46) -#define IRQ_NHCIMFCIR (IRQ_BOARD_END + 47) -#define IRQ_USB_PORT_RESUME (IRQ_BOARD_END + 48) -#define IRQ_S0_READY_NINT (IRQ_BOARD_END + 49) -#define IRQ_S1_READY_NINT (IRQ_BOARD_END + 50) -#define IRQ_S0_CD_VALID (IRQ_BOARD_END + 51) -#define IRQ_S1_CD_VALID (IRQ_BOARD_END + 52) -#define IRQ_S0_BVD1_STSCHG (IRQ_BOARD_END + 53) -#define IRQ_S1_BVD1_STSCHG (IRQ_BOARD_END + 54) - -#define IRQ_LOCOMO_START (IRQ_BOARD_END) -#define IRQ_LOCOMO_KEY (IRQ_BOARD_END + 0) -#define IRQ_LOCOMO_GPIO0 (IRQ_BOARD_END + 1) -#define IRQ_LOCOMO_GPIO1 (IRQ_BOARD_END + 2) -#define IRQ_LOCOMO_GPIO2 (IRQ_BOARD_END + 3) -#define IRQ_LOCOMO_GPIO3 (IRQ_BOARD_END + 4) -#define IRQ_LOCOMO_GPIO4 (IRQ_BOARD_END + 5) -#define IRQ_LOCOMO_GPIO5 (IRQ_BOARD_END + 6) -#define IRQ_LOCOMO_GPIO6 (IRQ_BOARD_END + 7) -#define IRQ_LOCOMO_GPIO7 (IRQ_BOARD_END + 8) -#define IRQ_LOCOMO_GPIO8 (IRQ_BOARD_END + 9) -#define IRQ_LOCOMO_GPIO9 (IRQ_BOARD_END + 10) -#define IRQ_LOCOMO_GPIO10 (IRQ_BOARD_END + 11) -#define IRQ_LOCOMO_GPIO11 (IRQ_BOARD_END + 12) -#define IRQ_LOCOMO_GPIO12 (IRQ_BOARD_END + 13) -#define IRQ_LOCOMO_GPIO13 (IRQ_BOARD_END + 14) -#define IRQ_LOCOMO_GPIO14 (IRQ_BOARD_END + 15) -#define IRQ_LOCOMO_GPIO15 (IRQ_BOARD_END + 16) -#define IRQ_LOCOMO_LT (IRQ_BOARD_END + 17) -#define IRQ_LOCOMO_SPI_RFR (IRQ_BOARD_END + 18) -#define IRQ_LOCOMO_SPI_RFW (IRQ_BOARD_END + 19) -#define IRQ_LOCOMO_SPI_OVRN (IRQ_BOARD_END + 20) -#define IRQ_LOCOMO_SPI_TEND (IRQ_BOARD_END + 21) - /* * Figure out the MAX IRQ number. * @@ -219,89 +143,16 @@ * Otherwise, we have the standard IRQs only. */ #ifdef CONFIG_SA1111 -#define NR_IRQS (IRQ_S1_BVD1_STSCHG + 1) -#elif defined(CONFIG_SHARP_LOCOMO) -#define NR_IRQS (IRQ_LOCOMO_SPI_TEND + 1) +#define NR_IRQS (IRQ_BOARD_END + 55) #elif defined(CONFIG_PXA_HAVE_BOARD_IRQS) #define NR_IRQS (IRQ_BOARD_END) #else #define NR_IRQS (IRQ_BOARD_START) #endif -/* - * Board specific IRQs. Define them here. - * Do not surround them with ifdefs. - */ -#define LUBBOCK_IRQ(x) (IRQ_BOARD_START + (x)) -#define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0) -#define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1) -#define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */ -#define LUBBOCK_ETH_IRQ LUBBOCK_IRQ(3) -#define LUBBOCK_UCB1400_IRQ LUBBOCK_IRQ(4) -#define LUBBOCK_BB_IRQ LUBBOCK_IRQ(5) -#define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */ -#define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6) - -#define LPD270_IRQ(x) (IRQ_BOARD_START + (x)) -#define LPD270_USBC_IRQ LPD270_IRQ(2) -#define LPD270_ETHERNET_IRQ LPD270_IRQ(3) -#define LPD270_AC97_IRQ LPD270_IRQ(4) - -#define MAINSTONE_IRQ(x) (IRQ_BOARD_START + (x)) -#define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0) -#define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1) -#define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2) -#define MAINSTONE_ETHERNET_IRQ MAINSTONE_IRQ(3) -#define MAINSTONE_AC97_IRQ MAINSTONE_IRQ(4) -#define MAINSTONE_PEN_IRQ MAINSTONE_IRQ(5) -#define MAINSTONE_MSINS_IRQ MAINSTONE_IRQ(6) -#define MAINSTONE_EXBRD_IRQ MAINSTONE_IRQ(7) -#define MAINSTONE_S0_CD_IRQ MAINSTONE_IRQ(9) -#define MAINSTONE_S0_STSCHG_IRQ MAINSTONE_IRQ(10) -#define MAINSTONE_S0_IRQ MAINSTONE_IRQ(11) -#define MAINSTONE_S1_CD_IRQ MAINSTONE_IRQ(13) -#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14) -#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15) - -/* Balloon3 Interrupts */ -#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x)) - -#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0) -#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1) - -#define BALLOON3_AUX_NIRQ IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ) -#define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ) -#define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD) - -/* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */ -#define IRQ_LOCOMO_KEY_BASE (IRQ_BOARD_START + 0) -#define IRQ_LOCOMO_GPIO_BASE (IRQ_BOARD_START + 1) -#define IRQ_LOCOMO_LT_BASE (IRQ_BOARD_START + 2) -#define IRQ_LOCOMO_SPI_BASE (IRQ_BOARD_START + 3) - -/* phyCORE-PXA270 (PCM027) Interrupts */ -#define PCM027_IRQ(x) (IRQ_BOARD_START + (x)) -#define PCM027_BTDET_IRQ PCM027_IRQ(0) -#define PCM027_FF_RI_IRQ PCM027_IRQ(1) -#define PCM027_MMCDET_IRQ PCM027_IRQ(2) -#define PCM027_PM_5V_IRQ PCM027_IRQ(3) - -/* ITE8152 irqs */ /* add IT8152 IRQs beyond BOARD_END */ #ifdef CONFIG_PCI_HOST_ITE8152 -#define IT8152_IRQ(x) (IRQ_BOARD_END + (x)) - -/* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */ -#define IT8152_LD_IRQ_COUNT 9 -#define IT8152_LP_IRQ_COUNT 16 -#define IT8152_PD_IRQ_COUNT 15 - -/* Priorities: */ -#define IT8152_PD_IRQ(i) IT8152_IRQ(i) -#define IT8152_LP_IRQ(i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT) -#define IT8152_LD_IRQ(i) (IT8152_IRQ(i) + IT8152_PD_IRQ_COUNT + IT8152_LP_IRQ_COUNT) - -#define IT8152_LAST_IRQ IT8152_LD_IRQ(IT8152_LD_IRQ_COUNT - 1) +#define IT8152_LAST_IRQ (IRQ_BOARD_END + 40) #if NR_IRQS < (IT8152_LAST_IRQ+1) #undef NR_IRQS diff --git a/arch/arm/mach-pxa/include/mach/lpd270.h b/arch/arm/mach-pxa/include/mach/lpd270.h index f89fb715266..0e6440c8168 100644 --- a/arch/arm/mach-pxa/include/mach/lpd270.h +++ b/arch/arm/mach-pxa/include/mach/lpd270.h @@ -34,5 +34,9 @@ #define LPD270_INT_ETHERNET (1 << 3) /* Ethernet controller IRQ */ #define LPD270_INT_USBC (1 << 2) /* USB client cable detection IRQ */ +#define LPD270_IRQ(x) (IRQ_BOARD_START + (x)) +#define LPD270_USBC_IRQ LPD270_IRQ(2) +#define LPD270_ETHERNET_IRQ LPD270_IRQ(3) +#define LPD270_AC97_IRQ LPD270_IRQ(4) #endif diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h index 751b74811d0..a0d4247f08f 100644 --- a/arch/arm/mach-pxa/include/mach/lubbock.h +++ b/arch/arm/mach-pxa/include/mach/lubbock.h @@ -34,6 +34,17 @@ #define LUB_IRQ_SET_CLR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x0d0) #define LUB_GP __LUB_REG(LUBBOCK_FPGA_PHYS + 0x100) +/* Board specific IRQs */ +#define LUBBOCK_IRQ(x) (IRQ_BOARD_START + (x)) +#define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0) +#define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1) +#define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */ +#define LUBBOCK_ETH_IRQ LUBBOCK_IRQ(3) +#define LUBBOCK_UCB1400_IRQ LUBBOCK_IRQ(4) +#define LUBBOCK_BB_IRQ LUBBOCK_IRQ(5) +#define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */ +#define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6) + #ifndef __ASSEMBLY__ extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set); #endif diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/include/mach/mainstone.h index 3461c4302ff..86e623abd64 100644 --- a/arch/arm/mach-pxa/include/mach/mainstone.h +++ b/arch/arm/mach-pxa/include/mach/mainstone.h @@ -117,4 +117,21 @@ #define MST_PCMCIA_PWR_VCC_33 0x8 /* voltage VCC = 3.3V */ #define MST_PCMCIA_PWR_VCC_50 0x4 /* voltage VCC = 5.0V */ +/* board specific IRQs */ +#define MAINSTONE_IRQ(x) (IRQ_BOARD_START + (x)) +#define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0) +#define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1) +#define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2) +#define MAINSTONE_ETHERNET_IRQ MAINSTONE_IRQ(3) +#define MAINSTONE_AC97_IRQ MAINSTONE_IRQ(4) +#define MAINSTONE_PEN_IRQ MAINSTONE_IRQ(5) +#define MAINSTONE_MSINS_IRQ MAINSTONE_IRQ(6) +#define MAINSTONE_EXBRD_IRQ MAINSTONE_IRQ(7) +#define MAINSTONE_S0_CD_IRQ MAINSTONE_IRQ(9) +#define MAINSTONE_S0_STSCHG_IRQ MAINSTONE_IRQ(10) +#define MAINSTONE_S0_IRQ MAINSTONE_IRQ(11) +#define MAINSTONE_S1_CD_IRQ MAINSTONE_IRQ(13) +#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14) +#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15) + #endif diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h index 9c787855cf2..cafadc33dfd 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h @@ -190,4 +190,36 @@ #define GPIO89_AC97_nRESET MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH) #endif /* CONFIG_CPU_PXA26x */ +/* commonly used pin configurations */ +#define GPIOxx_LCD_16BPP \ + GPIO58_LCD_LDD_0, \ + GPIO59_LCD_LDD_1, \ + GPIO60_LCD_LDD_2, \ + GPIO61_LCD_LDD_3, \ + GPIO62_LCD_LDD_4, \ + GPIO63_LCD_LDD_5, \ + GPIO64_LCD_LDD_6, \ + GPIO65_LCD_LDD_7, \ + GPIO66_LCD_LDD_8, \ + GPIO67_LCD_LDD_9, \ + GPIO68_LCD_LDD_10, \ + GPIO69_LCD_LDD_11, \ + GPIO70_LCD_LDD_12, \ + GPIO71_LCD_LDD_13, \ + GPIO72_LCD_LDD_14, \ + GPIO73_LCD_LDD_15 + +#define GPIOxx_LCD_DSTN_16BPP \ + GPIOxx_LCD_16BPP, \ + GPIO74_LCD_FCLK, \ + GPIO75_LCD_LCLK, \ + GPIO76_LCD_PCLK + +#define GPIOxx_LCD_TFT_16BPP \ + GPIOxx_LCD_16BPP, \ + GPIO74_LCD_FCLK, \ + GPIO75_LCD_LCLK, \ + GPIO76_LCD_PCLK, \ + GPIO77_LCD_BIAS + #endif /* __ASM_ARCH_MFP_PXA25X_H */ diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h index 6543c05f47e..ec0f0b0b674 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h @@ -434,5 +434,32 @@ #define GPIO112_nMSINS MFP_CFG_IN(GPIO112, AF2) #define GPIO32_MSSCLK MFP_CFG_OUT(GPIO32, AF1, DRIVE_LOW) +/* commonly used pin configurations */ +#define GPIOxx_LCD_16BPP \ + GPIO58_LCD_LDD_0, \ + GPIO59_LCD_LDD_1, \ + GPIO60_LCD_LDD_2, \ + GPIO61_LCD_LDD_3, \ + GPIO62_LCD_LDD_4, \ + GPIO63_LCD_LDD_5, \ + GPIO64_LCD_LDD_6, \ + GPIO65_LCD_LDD_7, \ + GPIO66_LCD_LDD_8, \ + GPIO67_LCD_LDD_9, \ + GPIO68_LCD_LDD_10, \ + GPIO69_LCD_LDD_11, \ + GPIO70_LCD_LDD_12, \ + GPIO71_LCD_LDD_13, \ + GPIO72_LCD_LDD_14, \ + GPIO73_LCD_LDD_15 + +#define GPIOxx_LCD_TFT_16BPP \ + GPIOxx_LCD_16BPP, \ + GPIO74_LCD_FCLK, \ + GPIO75_LCD_LCLK, \ + GPIO76_LCD_PCLK, \ + GPIO77_LCD_BIAS + + extern int keypad_set_wake(unsigned int on); #endif /* __ASM_ARCH_MFP_PXA27X_H */ diff --git a/arch/arm/mach-pxa/include/mach/mxm8x10.h b/arch/arm/mach-pxa/include/mach/mxm8x10.h new file mode 100644 index 00000000000..ffa15665a41 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mxm8x10.h @@ -0,0 +1,21 @@ +#ifndef __MACH_MXM_8X10_H +#define __MACH_MXM_8X10_H + +#define MXM_8X10_ETH_PHYS 0x13000000 + +#if defined(CONFIG_MMC) + +#define MXM_8X10_SD_nCD (72) +#define MXM_8X10_SD_WP (84) + +extern void mxm_8x10_mmc_init(void); +#else +static inline void mxm_8x10_mmc_init(void) {} +#endif + +extern void mxm_8x10_usb_host_init(void); +extern void mxm_8x10_ac97_init(void); + +extern void mxm_8x10_barebones_init(void); + +#endif /* __MACH_MXM_8X10_H */ diff --git a/arch/arm/mach-pxa/include/mach/pcm027.h b/arch/arm/mach-pxa/include/mach/pcm027.h index 4dcd2e8baa6..04083263167 100644 --- a/arch/arm/mach-pxa/include/mach/pcm027.h +++ b/arch/arm/mach-pxa/include/mach/pcm027.h @@ -23,6 +23,13 @@ * Definitions of CPU card resources only */ +/* phyCORE-PXA270 (PCM027) Interrupts */ +#define PCM027_IRQ(x) (IRQ_BOARD_START + (x)) +#define PCM027_BTDET_IRQ PCM027_IRQ(0) +#define PCM027_FF_RI_IRQ PCM027_IRQ(1) +#define PCM027_MMCDET_IRQ PCM027_IRQ(2) +#define PCM027_PM_5V_IRQ PCM027_IRQ(3) + /* I2C RTC */ #define PCM027_RTC_IRQ_GPIO 0 #define PCM027_RTC_IRQ IRQ_GPIO(PCM027_RTC_IRQ_GPIO) diff --git a/arch/arm/mach-pxa/include/mach/ssp.h b/arch/arm/mach-pxa/include/mach/ssp.h index cb5cb766f0f..be1be5b6db5 100644 --- a/arch/arm/mach-pxa/include/mach/ssp.h +++ b/arch/arm/mach-pxa/include/mach/ssp.h @@ -46,6 +46,7 @@ struct ssp_device { int drcmr_tx; }; +#ifdef CONFIG_PXA_SSP_LEGACY /* * SSP initialisation flags */ @@ -78,6 +79,7 @@ void ssp_restore_state(struct ssp_dev *dev, struct ssp_state *ssp); int ssp_init(struct ssp_dev *dev, u32 port, u32 init_flags); int ssp_config(struct ssp_dev *dev, u32 mode, u32 flags, u32 psp_flags, u32 speed); void ssp_exit(struct ssp_dev *dev); +#endif /* CONFIG_PXA_SSP_LEGACY */ /** * ssp_write_reg - Write to a SSP register diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h index 237734b5b1b..5ef91d9d17e 100644 --- a/arch/arm/mach-pxa/include/mach/uncompress.h +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -10,20 +10,41 @@ */ #include <linux/serial_reg.h> -#include <mach/regs-uart.h> #include <asm/mach-types.h> -#define __REG(x) ((volatile unsigned long *)x) +#define FFUART_BASE (0x40100000) +#define BTUART_BASE (0x40200000) +#define STUART_BASE (0x40700000) -static volatile unsigned long *UART = FFUART; +static unsigned long uart_base = FFUART_BASE; +static unsigned int uart_shift = 2; +static unsigned int uart_is_pxa = 1; + +static inline unsigned char uart_read(int offset) +{ + return *(volatile unsigned char *)(uart_base + (offset << uart_shift)); +} + +static inline void uart_write(unsigned char val, int offset) +{ + *(volatile unsigned char *)(uart_base + (offset << uart_shift)) = val; +} + +static inline int uart_is_enabled(void) +{ + /* assume enabled by default for non-PXA uarts */ + return uart_is_pxa ? uart_read(UART_IER) & UART_IER_UUE : 1; +} static inline void putc(char c) { - if (!(UART[UART_IER] & IER_UUE)) + if (!uart_is_enabled()) return; - while (!(UART[UART_LSR] & LSR_TDRQ)) + + while (!(uart_read(UART_LSR) & UART_LSR_THRE)) barrier(); - UART[UART_TX] = c; + + uart_write(c, UART_TX); } /* @@ -38,7 +59,13 @@ static inline void arch_decomp_setup(void) if (machine_is_littleton() || machine_is_intelmote2() || machine_is_csb726() || machine_is_stargate2() || machine_is_cm_x300() || machine_is_balloon3()) - UART = STUART; + uart_base = STUART_BASE; + + if (machine_is_arcom_zeus()) { + uart_base = 0x10000000; /* nCS4 */ + uart_shift = 1; + uart_is_pxa = 0; + } } /* diff --git a/arch/arm/mach-pxa/include/mach/zeus.h b/arch/arm/mach-pxa/include/mach/zeus.h index c387046d2f2..6e119976003 100644 --- a/arch/arm/mach-pxa/include/mach/zeus.h +++ b/arch/arm/mach-pxa/include/mach/zeus.h @@ -58,6 +58,8 @@ #define ZEUS_EXT1_GPIO(x) (ZEUS_EXT1_GPIO_BASE + (x)) #define ZEUS_USER_GPIO(x) (ZEUS_USER_GPIO_BASE + (x)) +#define ZEUS_CAN_SHDN_GPIO ZEUS_EXT1_GPIO(2) + /* * CPLD registers: * Only 4 registers, but spreaded over a 32MB address space. @@ -68,7 +70,6 @@ #define ZEUS_CPLD_VERSION (ZEUS_CPLD + 0x0000) #define ZEUS_CPLD_ISA_IRQ (ZEUS_CPLD + 0x1000) #define ZEUS_CPLD_CONTROL (ZEUS_CPLD + 0x2000) -#define ZEUS_CPLD_EXTWDOG (ZEUS_CPLD + 0x3000) /* CPLD register bits */ #define ZEUS_CPLD_CONTROL_CF_RST 0x01 diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c index 1373c22dbb8..d279507fc74 100644 --- a/arch/arm/mach-pxa/lpd270.c +++ b/arch/arm/mach-pxa/lpd270.c @@ -83,6 +83,10 @@ static unsigned long lpd270_pin_config[] __initdata = { GPIO89_USBH1_PEN, /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, GPIO45_AC97_SYSCLK, GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH, @@ -121,7 +125,7 @@ static void lpd270_irq_handler(unsigned int irq, struct irq_desc *desc) pending = __raw_readw(LPD270_INT_STATUS) & lpd270_irq_enabled; do { - GEDR(0) = GPIO_bit(0); /* clear useless edge notification */ + desc->chip->ack(irq); /* clear useless edge notification */ if (likely(pending)) { irq = LPD270_IRQ(0) + __ffs(pending); generic_handle_irq(irq); diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c index 98ee7e59029..63d65a2a038 100644 --- a/arch/arm/mach-pxa/lubbock.c +++ b/arch/arm/mach-pxa/lubbock.c @@ -66,26 +66,14 @@ static unsigned long lubbock_pin_config[] __initdata = { GPIO25_SSP1_TXD, GPIO26_SSP1_RXD, + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + /* LCD - 16bpp DSTN */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, + GPIOxx_LCD_DSTN_16BPP, /* BTUART */ GPIO42_BTUART_RXD, @@ -158,7 +146,7 @@ static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc) { unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled; do { - GEDR(0) = GPIO_bit(0); /* clear our parent irq */ + desc->chip->ack(irq); /* clear our parent irq */ if (likely(pending)) { irq = LUBBOCK_IRQ(0) + __ffs(pending); generic_handle_irq(irq); @@ -240,11 +228,18 @@ static struct resource sa1111_resources[] = { }, }; +static struct sa1111_platform_data sa1111_info = { + .irq_base = IRQ_BOARD_END, +}; + static struct platform_device sa1111_device = { .name = "sa1111", .id = -1, .num_resources = ARRAY_SIZE(sa1111_resources), .resource = sa1111_resources, + .dev = { + .platform_data = &sa1111_info, + }, }; /* ADS7846 is connected through SSP ... and if your board has J5 populated, diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c index 189f330719a..e81dd0c8e40 100644 --- a/arch/arm/mach-pxa/magician.c +++ b/arch/arm/mach-pxa/magician.c @@ -88,26 +88,7 @@ static unsigned long magician_pin_config[] __initdata = { GPIO112_MMC_CMD, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* QCI */ GPIO12_CIF_DD_7, diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index 851ee0fc32e..5543c64da9e 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c @@ -60,26 +60,7 @@ static unsigned long mainstone_pin_config[] = { GPIO15_nCS_1, /* LCD - 16bpp Active TFT */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, GPIO16_PWM0_OUT, /* Backlight */ /* MMC */ @@ -107,6 +88,10 @@ static unsigned long mainstone_pin_config[] = { GPIO57_nIOIS16, /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, GPIO45_AC97_SYSCLK, /* Keypad */ @@ -162,7 +147,7 @@ static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc) { unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled; do { - GEDR(0) = GPIO_bit(0); /* clear useless edge notification */ + desc->chip->ack(irq); /* clear useless edge notification */ if (likely(pending)) { irq = MAINSTONE_IRQ(0) + __ffs(pending); generic_handle_irq(irq); diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c index 2466a44d8fd..843fcca76e2 100644 --- a/arch/arm/mach-pxa/mioa701.c +++ b/arch/arm/mach-pxa/mioa701.c @@ -86,25 +86,7 @@ static unsigned long mioa701_pin_config[] = { MIO_CFG_OUT(GPIO22_USB_ENABLE, AF0, DRIVE_LOW), /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, + GPIOxx_LCD_TFT_16BPP, /* QCI */ GPIO12_CIF_DD_7, @@ -155,6 +137,10 @@ static unsigned long mioa701_pin_config[] = { GPIO41_FFUART_RTS, /* Sound */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, GPIO89_AC97_SYSCLK, MIO_CFG_IN(GPIO12_HPJACK_INSERT, AF0), diff --git a/arch/arm/mach-pxa/mxm8x10.c b/arch/arm/mach-pxa/mxm8x10.c new file mode 100644 index 00000000000..8c9c6f0d56b --- /dev/null +++ b/arch/arm/mach-pxa/mxm8x10.c @@ -0,0 +1,474 @@ +/* + * linux/arch/arm/mach-pxa/mxm8x10.c + * + * Support for the Embedian MXM-8x10 Computer on Module + * + * Copyright (C) 2006 Marvell International Ltd. + * Copyright (C) 2009 Embedian Inc. + * Copyright (C) 2009 TMT Services & Supplies (Pty) Ltd. + * + * 2007-09-04: eric miao <eric.y.miao@gmail.com> + * rewrite to align with latest kernel + * + * 2010-01-09: Edwin Peer <epeer@tmtservices.co.za> + * Hennie van der Merwe <hvdmerwe@tmtservices.co.za> + * rework for upstream merge + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/serial_8250.h> +#include <linux/dm9000.h> +#include <linux/gpio.h> + +#include <plat/i2c.h> +#include <plat/pxa3xx_nand.h> + +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <mach/ohci.h> +#include <mach/pxa320.h> + +#include <mach/mxm8x10.h> + +#include "devices.h" +#include "generic.h" + +/* GPIO pin definition + +External device stuff - Leave unconfigured for now... +--------------------- +GPIO0 - DREQ (External DMA Request) +GPIO3 - nGCS2 (External Chip Select) Where is nGCS0; nGCS1; nGCS4; nGCS5 ? +GPIO4 - nGCS3 +GPIO15 - EXT_GPIO1 +GPIO16 - EXT_GPIO2 +GPIO17 - EXT_GPIO3 +GPIO24 - EXT_GPIO4 +GPIO25 - EXT_GPIO5 +GPIO26 - EXT_GPIO6 +GPIO27 - EXT_GPIO7 +GPIO28 - EXT_GPIO8 +GPIO29 - EXT_GPIO9 +GPIO30 - EXT_GPIO10 +GPIO31 - EXT_GPIO11 +GPIO57 - EXT_GPIO12 +GPIO74 - EXT_IRQ1 +GPIO75 - EXT_IRQ2 +GPIO76 - EXT_IRQ3 +GPIO77 - EXT_IRQ4 +GPIO78 - EXT_IRQ5 +GPIO79 - EXT_IRQ6 +GPIO80 - EXT_IRQ7 +GPIO81 - EXT_IRQ8 +GPIO87 - VCCIO_PWREN (External Device PWREN) + +Dallas 1-Wire - Leave unconfigured for now... +------------- +GPIO0_2 - DS - 1Wire + +Ethernet +-------- +GPIO1 - DM9000 PWR +GPIO9 - DM9K_nIRQ +GPIO36 - DM9K_RESET + +Keypad - Leave unconfigured by for now... +------ +GPIO1_2 - KP_DKIN0 +GPIO5_2 - KP_MKOUT7 +GPIO82 - KP_DKIN1 +GPIO85 - KP_DKIN2 +GPIO86 - KP_DKIN3 +GPIO113 - KP_MKIN0 +GPIO114 - KP_MKIN1 +GPIO115 - KP_MKIN2 +GPIO116 - KP_MKIN3 +GPIO117 - KP_MKIN4 +GPIO118 - KP_MKIN5 +GPIO119 - KP_MKIN6 +GPIO120 - KP_MKIN7 +GPIO121 - KP_MKOUT0 +GPIO122 - KP_MKOUT1 +GPIO122 - KP_MKOUT2 +GPIO123 - KP_MKOUT3 +GPIO124 - KP_MKOUT4 +GPIO125 - KP_MKOUT5 +GPIO127 - KP_MKOUT6 + +Data Bus - Leave unconfigured for now... +-------- +GPIO2 - nWait (Data Bus) + +USB Device +---------- +GPIO4_2 - USBD_PULLUP +GPIO10 - UTM_CLK (USB Device UTM Clk) +GPIO49 - USB 2.0 Device UTM_DATA0 +GPIO50 - USB 2.0 Device UTM_DATA1 +GPIO51 - USB 2.0 Device UTM_DATA2 +GPIO52 - USB 2.0 Device UTM_DATA3 +GPIO53 - USB 2.0 Device UTM_DATA4 +GPIO54 - USB 2.0 Device UTM_DATA5 +GPIO55 - USB 2.0 Device UTM_DATA6 +GPIO56 - USB 2.0 Device UTM_DATA7 +GPIO58 - UTM_RXVALID (USB 2.0 Device) +GPIO59 - UTM_RXACTIVE (USB 2.0 Device) +GPIO60 - UTM_RXERROR +GPIO61 - UTM_OPMODE0 +GPIO62 - UTM_OPMODE1 +GPIO71 - USBD_INT (USB Device?) +GPIO73 - UTM_TXREADY (USB 2.0 Device) +GPIO83 - UTM_TXVALID (USB 2.0 Device) +GPIO98 - UTM_RESET (USB 2.0 device) +GPIO99 - UTM_XCVR_SELECT +GPIO100 - UTM_TERM_SELECT +GPIO101 - UTM_SUSPENDM_X +GPIO102 - UTM_LINESTATE0 +GPIO103 - UTM_LINESTATE1 + +Card-Bus Interface - Leave unconfigured for now... +------------------ +GPIO5 - nPIOR (I/O space output enable) +GPIO6 - nPIOW (I/O space write enable) +GPIO7 - nIOS16 (Input from I/O space telling size of data bus) +GPIO8 - nPWAIT (Input for inserting wait states) + +LCD +--- +GPIO6_2 - LDD0 +GPIO7_2 - LDD1 +GPIO8_2 - LDD2 +GPIO9_2 - LDD3 +GPIO11_2 - LDD5 +GPIO12_2 - LDD6 +GPIO13_2 - LDD7 +GPIO14_2 - VSYNC +GPIO15_2 - HSYNC +GPIO16_2 - VCLK +GPIO17_2 - HCLK +GPIO18_2 - VDEN +GPIO63 - LDD8 (CPU LCD) +GPIO64 - LDD9 (CPU LCD) +GPIO65 - LDD10 (CPU LCD) +GPIO66 - LDD11 (CPU LCD) +GPIO67 - LDD12 (CPU LCD) +GPIO68 - LDD13 (CPU LCD) +GPIO69 - LDD14 (CPU LCD) +GPIO70 - LDD15 (CPU LCD) +GPIO88 - VCCLCD_PWREN (LCD Panel PWREN) +GPIO97 - BACKLIGHT_EN +GPIO104 - LCD_PWREN + +PWM - Leave unconfigured for now... +--- +GPIO11 - PWM0 +GPIO12 - PWM1 +GPIO13 - PWM2 +GPIO14 - PWM3 + +SD-CARD +------- +GPIO18 - SDDATA0 +GPIO19 - SDDATA1 +GPIO20 - SDDATA2 +GPIO21 - SDDATA3 +GPIO22 - SDCLK +GPIO23 - SDCMD +GPIO72 - SD_WP +GPIO84 - SD_nIRQ_CD (SD-Card) + +I2C +--- +GPIO32 - I2CSCL +GPIO33 - I2CSDA + +AC97 +---- +GPIO35 - AC97_SDATA_IN +GPIO37 - AC97_SDATA_OUT +GPIO38 - AC97_SYNC +GPIO39 - AC97_BITCLK +GPIO40 - AC97_nRESET + +UART1 +----- +GPIO41 - UART_RXD1 +GPIO42 - UART_TXD1 +GPIO43 - UART_CTS1 +GPIO44 - UART_DCD1 +GPIO45 - UART_DSR1 +GPIO46 - UART_nRI1 +GPIO47 - UART_DTR1 +GPIO48 - UART_RTS1 + +UART2 +----- +GPIO109 - RTS2 +GPIO110 - RXD2 +GPIO111 - TXD2 +GPIO112 - nCTS2 + +UART3 +----- +GPIO105 - nCTS3 +GPIO106 - nRTS3 +GPIO107 - TXD3 +GPIO108 - RXD3 + +SSP3 - Leave unconfigured for now... +---- +GPIO89 - SSP3_CLK +GPIO90 - SSP3_SFRM +GPIO91 - SSP3_TXD +GPIO92 - SSP3_RXD + +SSP4 +GPIO93 - SSP4_CLK +GPIO94 - SSP4_SFRM +GPIO95 - SSP4_TXD +GPIO96 - SSP4_RXD +*/ + +static mfp_cfg_t mfp_cfg[] __initdata = { + /* USB */ + GPIO10_UTM_CLK, + GPIO49_U2D_PHYDATA_0, + GPIO50_U2D_PHYDATA_1, + GPIO51_U2D_PHYDATA_2, + GPIO52_U2D_PHYDATA_3, + GPIO53_U2D_PHYDATA_4, + GPIO54_U2D_PHYDATA_5, + GPIO55_U2D_PHYDATA_6, + GPIO56_U2D_PHYDATA_7, + GPIO58_UTM_RXVALID, + GPIO59_UTM_RXACTIVE, + GPIO60_U2D_RXERROR, + GPIO61_U2D_OPMODE0, + GPIO62_U2D_OPMODE1, + GPIO71_GPIO, /* USBD_INT */ + GPIO73_UTM_TXREADY, + GPIO83_U2D_TXVALID, + GPIO98_U2D_RESET, + GPIO99_U2D_XCVR_SEL, + GPIO100_U2D_TERM_SEL, + GPIO101_U2D_SUSPEND, + GPIO102_UTM_LINESTATE_0, + GPIO103_UTM_LINESTATE_1, + GPIO4_2_GPIO | MFP_PULL_HIGH, /* UTM_PULLUP */ + + /* DM9000 */ + GPIO1_GPIO, + GPIO9_GPIO, + GPIO36_GPIO, + + /* AC97 */ + GPIO35_AC97_SDATA_IN_0, + GPIO37_AC97_SDATA_OUT, + GPIO38_AC97_SYNC, + GPIO39_AC97_BITCLK, + GPIO40_AC97_nACRESET, + + /* UARTS */ + GPIO41_UART1_RXD, + GPIO42_UART1_TXD, + GPIO43_UART1_CTS, + GPIO44_UART1_DCD, + GPIO45_UART1_DSR, + GPIO46_UART1_RI, + GPIO47_UART1_DTR, + GPIO48_UART1_RTS, + + GPIO109_UART2_RTS, + GPIO110_UART2_RXD, + GPIO111_UART2_TXD, + GPIO112_UART2_CTS, + + GPIO105_UART3_CTS, + GPIO106_UART3_RTS, + GPIO107_UART3_TXD, + GPIO108_UART3_RXD, + + GPIO78_GPIO, + GPIO79_GPIO, + GPIO80_GPIO, + GPIO81_GPIO, + + /* I2C */ + GPIO32_I2C_SCL, + GPIO33_I2C_SDA, + + /* MMC */ + GPIO18_MMC1_DAT0, + GPIO19_MMC1_DAT1, + GPIO20_MMC1_DAT2, + GPIO21_MMC1_DAT3, + GPIO22_MMC1_CLK, + GPIO23_MMC1_CMD, + GPIO72_GPIO | MFP_PULL_HIGH, /* Card Detect */ + GPIO84_GPIO | MFP_PULL_LOW, /* Write Protect */ + + /* IRQ */ + GPIO74_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ1 */ + GPIO75_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ2 */ + GPIO76_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ3 */ + GPIO77_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ4 */ + GPIO78_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ5 */ + GPIO79_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ6 */ + GPIO80_GPIO | MFP_LPM_EDGE_RISE, /* EXT_IRQ7 */ + GPIO81_GPIO | MFP_LPM_EDGE_RISE /* EXT_IRQ8 */ +}; + +/* MMC/MCI Support */ +#if defined(CONFIG_MMC) +static struct pxamci_platform_data mxm_8x10_mci_platform_data = { + .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, + .detect_delay = 1, + .gpio_card_detect = MXM_8X10_SD_nCD, + .gpio_card_ro = MXM_8X10_SD_WP, + .gpio_power = -1 +}; + +void __init mxm_8x10_mmc_init(void) +{ + pxa_set_mci_info(&mxm_8x10_mci_platform_data); +} +#endif + +/* USB Open Host Controler Interface */ +static struct pxaohci_platform_data mxm_8x10_ohci_platform_data = { + .port_mode = PMM_NPS_MODE, + .flags = ENABLE_PORT_ALL +}; + +void __init mxm_8x10_usb_host_init(void) +{ + pxa_set_ohci_info(&mxm_8x10_ohci_platform_data); +} + +/* AC97 Sound Support */ +static struct platform_device mxm_8x10_ac97_device = { + .name = "pxa2xx-ac97" +}; + +void __init mxm_8x10_ac97_init(void) +{ + platform_device_register(&mxm_8x10_ac97_device); +} + +/* NAND flash Support */ +#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE) +#define NAND_BLOCK_SIZE SZ_128K +#define NB(x) (NAND_BLOCK_SIZE * (x)) +static struct mtd_partition mxm_8x10_nand_partitions[] = { + [0] = { + .name = "boot", + .size = NB(0x002), + .offset = NB(0x000), + .mask_flags = MTD_WRITEABLE + }, + [1] = { + .name = "kernel", + .size = NB(0x010), + .offset = NB(0x002), + .mask_flags = MTD_WRITEABLE + }, + [2] = { + .name = "root", + .size = NB(0x36c), + .offset = NB(0x012) + }, + [3] = { + .name = "bbt", + .size = NB(0x082), + .offset = NB(0x37e), + .mask_flags = MTD_WRITEABLE + } +}; + +static struct pxa3xx_nand_platform_data mxm_8x10_nand_info = { + .enable_arbiter = 1, + .keep_config = 1, + .parts = mxm_8x10_nand_partitions, + .nr_parts = ARRAY_SIZE(mxm_8x10_nand_partitions) +}; + +static void __init mxm_8x10_nand_init(void) +{ + pxa3xx_set_nand_info(&mxm_8x10_nand_info); +} +#else +static inline void mxm_8x10_nand_init(void) {} +#endif /* CONFIG_MTD_NAND_PXA3xx || CONFIG_MTD_NAND_PXA3xx_MODULE */ + +/* Ethernet support: Davicom DM9000 */ +static struct resource dm9k_resources[] = { + [0] = { + .start = MXM_8X10_ETH_PHYS + 0x300, + .end = MXM_8X10_ETH_PHYS + 0x300, + .flags = IORESOURCE_MEM + }, + [1] = { + .start = MXM_8X10_ETH_PHYS + 0x308, + .end = MXM_8X10_ETH_PHYS + 0x308, + .flags = IORESOURCE_MEM + }, + [2] = { + .start = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO9)), + .end = gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO9)), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE + } +}; + +static struct dm9000_plat_data dm9k_plat_data = { + .flags = DM9000_PLATF_16BITONLY +}; + +static struct platform_device dm9k_device = { + .name = "dm9000", + .id = 0, + .num_resources = ARRAY_SIZE(dm9k_resources), + .resource = dm9k_resources, + .dev = { + .platform_data = &dm9k_plat_data + } +}; + +static void __init mxm_8x10_ethernet_init(void) +{ + platform_device_register(&dm9k_device); +} + +/* PXA UARTs */ +static void __init mxm_8x10_uarts_init(void) +{ + pxa_set_ffuart_info(NULL); + pxa_set_btuart_info(NULL); + pxa_set_stuart_info(NULL); +} + +/* I2C and Real Time Clock */ +static struct i2c_board_info __initdata mxm_8x10_i2c_devices[] = { + { + I2C_BOARD_INFO("ds1337", 0x68) + } +}; + +static void __init mxm_8x10_i2c_init(void) +{ + i2c_register_board_info(0, mxm_8x10_i2c_devices, + ARRAY_SIZE(mxm_8x10_i2c_devices)); + pxa_set_i2c_info(NULL); +} + +void __init mxm_8x10_barebones_init(void) +{ + pxa3xx_mfp_config(ARRAY_AND_SIZE(mfp_cfg)); + + mxm_8x10_uarts_init(); + mxm_8x10_nand_init(); + mxm_8x10_i2c_init(); + mxm_8x10_ethernet_init(); +} diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c index e100af78b16..f70c75b3876 100644 --- a/arch/arm/mach-pxa/palmld.c +++ b/arch/arm/mach-pxa/palmld.c @@ -83,26 +83,7 @@ static unsigned long palmld_pin_config[] __initdata = { GPIO105_KP_MKOUT_2, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* PWM */ GPIO16_PWM0_OUT, diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c index 8fe3ec27568..d902a813aae 100644 --- a/arch/arm/mach-pxa/palmt5.c +++ b/arch/arm/mach-pxa/palmt5.c @@ -87,26 +87,7 @@ static unsigned long palmt5_pin_config[] __initdata = { GPIO105_KP_MKOUT_2, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* PWM */ GPIO16_PWM0_OUT, diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index b992f07ece2..717d7a63867 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -84,26 +84,7 @@ static unsigned long palmtc_pin_config[] __initdata = { GPIO36_GPIO, /* pullup */ /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* MATRIX KEYPAD */ GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 0 */ diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c index dc728d6ab94..3d284ff1a64 100644 --- a/arch/arm/mach-pxa/palmte2.c +++ b/arch/arm/mach-pxa/palmte2.c @@ -73,26 +73,7 @@ static unsigned long palmte2_pin_config[] __initdata = { GPIO47_FICP_TXD, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* GPIO KEYS */ GPIO5_GPIO, /* notes */ diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c index b433bb49671..d8b4469607a 100644 --- a/arch/arm/mach-pxa/palmtreo.c +++ b/arch/arm/mach-pxa/palmtreo.c @@ -99,25 +99,7 @@ static unsigned long treo_pin_config[] __initdata = { GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH, /* Hotsync button */ /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, + GPIOxx_LCD_TFT_16BPP, /* Quick Capture Interface */ GPIO84_CIF_FV, diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index b37a025c0b7..007b58c11f8 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -110,26 +110,7 @@ static unsigned long palmtx_pin_config[] __initdata = { GPIO105_KP_MKOUT_2, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* FFUART */ GPIO34_FFUART_RXD, diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c index 1c5d68a9451..3a7925ca394 100644 --- a/arch/arm/mach-pxa/palmz72.c +++ b/arch/arm/mach-pxa/palmz72.c @@ -95,26 +95,8 @@ static unsigned long palmz72_pin_config[] __initdata = { GPIO105_KP_MKOUT_2, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, + GPIO20_GPIO, /* bl power */ GPIO21_GPIO, /* LCD border switch */ GPIO22_GPIO, /* LCD border color */ diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c index d5255ae74fe..9d0ecea1760 100644 --- a/arch/arm/mach-pxa/pcm990-baseboard.c +++ b/arch/arm/mach-pxa/pcm990-baseboard.c @@ -58,6 +58,12 @@ static unsigned long pcm990_pin_config[] __initdata = { /* I2C */ GPIO117_I2C_SCL, GPIO118_I2C_SDA, + + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, }; /* @@ -259,8 +265,7 @@ static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc) unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled; do { - GEDR(PCM990_CTRL_INT_IRQ_GPIO) = - GPIO_bit(PCM990_CTRL_INT_IRQ_GPIO); + desc->chip->ack(irq); /* clear our parent IRQ */ if (likely(pending)) { irq = PCM027_IRQ(0) + __ffs(pending); generic_handle_irq(irq); diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c index c2b938a4d5c..d58a52415d7 100644 --- a/arch/arm/mach-pxa/poodle.c +++ b/arch/arm/mach-pxa/poodle.c @@ -91,26 +91,7 @@ static unsigned long poodle_pin_config[] __initdata = { GPIO35_FFUART_CTS, /* LCD */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* PC Card */ GPIO48_nPOE, @@ -193,11 +174,18 @@ static struct resource locomo_resources[] = { }, }; +static struct locomo_platform_data locomo_info = { + .irq_base = IRQ_BOARD_START, +}; + struct platform_device poodle_locomo_device = { .name = "locomo", .id = 0, .num_resources = ARRAY_SIZE(locomo_resources), .resource = locomo_resources, + .dev = { + .platform_data = &locomo_info, + }, }; EXPORT_SYMBOL(poodle_locomo_device); diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c index d783123e2d4..0af36177ff0 100644 --- a/arch/arm/mach-pxa/pxa27x.c +++ b/arch/arm/mach-pxa/pxa27x.c @@ -40,6 +40,25 @@ void pxa27x_clear_otgph(void) } EXPORT_SYMBOL(pxa27x_clear_otgph); +static unsigned long ac97_reset_config[] = { + GPIO95_AC97_nRESET, + GPIO95_GPIO, + GPIO113_AC97_nRESET, + GPIO113_GPIO, +}; + +void pxa27x_assert_ac97reset(int reset_gpio, int on) +{ + if (reset_gpio == 113) + pxa2xx_mfp_config(on ? &ac97_reset_config[0] : + &ac97_reset_config[1], 1); + + if (reset_gpio == 95) + pxa2xx_mfp_config(on ? &ac97_reset_config[2] : + &ac97_reset_config[3], 1); +} +EXPORT_SYMBOL_GPL(pxa27x_assert_ac97reset); + /* Crystal clock: 13MHz */ #define BASE_CLK 13000000 diff --git a/arch/arm/mach-pxa/raumfeld.c b/arch/arm/mach-pxa/raumfeld.c new file mode 100644 index 00000000000..3184bdc1452 --- /dev/null +++ b/arch/arm/mach-pxa/raumfeld.c @@ -0,0 +1,1108 @@ +/* + * arch/arm/mach-pxa/raumfeld.c + * + * Support for the following Raumfeld devices: + * + * * Controller + * * Connector + * * Speaker S/M + * + * See http://www.raumfeld.com for details. + * + * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/sysdev.h> +#include <linux/platform_device.h> +#include <linux/interrupt.h> +#include <linux/gpio.h> +#include <linux/smsc911x.h> +#include <linux/input.h> +#include <linux/rotary_encoder.h> +#include <linux/gpio_keys.h> +#include <linux/input/eeti_ts.h> +#include <linux/leds.h> +#include <linux/w1-gpio.h> +#include <linux/sched.h> +#include <linux/pwm_backlight.h> +#include <linux/i2c.h> +#include <linux/spi/spi.h> +#include <linux/spi/spi_gpio.h> +#include <linux/lis3lv02d.h> +#include <linux/pda_power.h> +#include <linux/power_supply.h> +#include <linux/pda_power.h> +#include <linux/power_supply.h> +#include <linux/regulator/max8660.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <linux/regulator/consumer.h> +#include <linux/delay.h> + +#include <asm/mach-types.h> +#include <asm/mach/arch.h> + +#include <mach/hardware.h> +#include <mach/pxa3xx-regs.h> +#include <mach/mfp-pxa3xx.h> +#include <mach/mfp-pxa300.h> +#include <mach/ohci.h> +#include <mach/pxafb.h> +#include <mach/mmc.h> +#include <plat/i2c.h> +#include <plat/pxa3xx_nand.h> + +#include "generic.h" +#include "devices.h" +#include "clock.h" + +/* common GPIO definitions */ + +/* inputs */ +#define GPIO_ON_OFF (14) +#define GPIO_VOLENC_A (19) +#define GPIO_VOLENC_B (20) +#define GPIO_CHARGE_DONE (23) +#define GPIO_CHARGE_IND (27) +#define GPIO_TOUCH_IRQ (32) +#define GPIO_ETH_IRQ (40) +#define GPIO_SPI_MISO (98) +#define GPIO_ACCEL_IRQ (104) +#define GPIO_RESCUE_BOOT (115) +#define GPIO_DOCK_DETECT (116) +#define GPIO_KEY1 (117) +#define GPIO_KEY2 (118) +#define GPIO_KEY3 (119) +#define GPIO_CHARGE_USB_OK (112) +#define GPIO_CHARGE_DC_OK (101) +#define GPIO_CHARGE_USB_SUSP (102) + +/* outputs */ +#define GPIO_SHUTDOWN_SUPPLY (16) +#define GPIO_SHUTDOWN_BATT (18) +#define GPIO_CHRG_PEN2 (31) +#define GPIO_TFT_VA_EN (33) +#define GPIO_SPDIF_CS (34) +#define GPIO_LED2 (35) +#define GPIO_LED1 (36) +#define GPIO_SPDIF_RESET (38) +#define GPIO_SPI_CLK (95) +#define GPIO_MCLK_DAC_CS (96) +#define GPIO_SPI_MOSI (97) +#define GPIO_W1_PULLUP_ENABLE (105) +#define GPIO_DISPLAY_ENABLE (106) +#define GPIO_MCLK_RESET (111) +#define GPIO_W2W_RESET (113) +#define GPIO_W2W_PDN (114) +#define GPIO_CODEC_RESET (120) +#define GPIO_AUDIO_VA_ENABLE (124) +#define GPIO_ACCEL_CS (125) +#define GPIO_ONE_WIRE (126) + +/* + * GPIO configurations + */ +static mfp_cfg_t raumfeld_controller_pin_config[] __initdata = { + /* UART1 */ + GPIO77_UART1_RXD, + GPIO78_UART1_TXD, + GPIO79_UART1_CTS, + GPIO81_UART1_DSR, + GPIO83_UART1_DTR, + GPIO84_UART1_RTS, + + /* UART3 */ + GPIO110_UART3_RXD, + + /* USB Host */ + GPIO0_2_USBH_PEN, + GPIO1_2_USBH_PWR, + + /* I2C */ + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + + /* SPI */ + GPIO34_GPIO, /* SPDIF_CS */ + GPIO96_GPIO, /* MCLK_CS */ + GPIO125_GPIO, /* ACCEL_CS */ + + /* MMC */ + GPIO3_MMC1_DAT0, + GPIO4_MMC1_DAT1, + GPIO5_MMC1_DAT2, + GPIO6_MMC1_DAT3, + GPIO7_MMC1_CLK, + GPIO8_MMC1_CMD, + + /* One-wire */ + GPIO126_GPIO | MFP_LPM_FLOAT, + GPIO105_GPIO | MFP_PULL_LOW | MFP_LPM_PULL_LOW, + + /* CHRG_USB_OK */ + GPIO101_GPIO | MFP_PULL_HIGH, + /* CHRG_USB_OK */ + GPIO112_GPIO | MFP_PULL_HIGH, + /* CHRG_USB_SUSP */ + GPIO102_GPIO, + /* DISPLAY_ENABLE */ + GPIO106_GPIO, + /* DOCK_DETECT */ + GPIO116_GPIO | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + + /* LCD */ + GPIO54_LCD_LDD_0, + GPIO55_LCD_LDD_1, + GPIO56_LCD_LDD_2, + GPIO57_LCD_LDD_3, + GPIO58_LCD_LDD_4, + GPIO59_LCD_LDD_5, + GPIO60_LCD_LDD_6, + GPIO61_LCD_LDD_7, + GPIO62_LCD_LDD_8, + GPIO63_LCD_LDD_9, + GPIO64_LCD_LDD_10, + GPIO65_LCD_LDD_11, + GPIO66_LCD_LDD_12, + GPIO67_LCD_LDD_13, + GPIO68_LCD_LDD_14, + GPIO69_LCD_LDD_15, + GPIO70_LCD_LDD_16, + GPIO71_LCD_LDD_17, + GPIO72_LCD_FCLK, + GPIO73_LCD_LCLK, + GPIO74_LCD_PCLK, + GPIO75_LCD_BIAS, +}; + +static mfp_cfg_t raumfeld_connector_pin_config[] __initdata = { + /* UART1 */ + GPIO77_UART1_RXD, + GPIO78_UART1_TXD, + GPIO79_UART1_CTS, + GPIO81_UART1_DSR, + GPIO83_UART1_DTR, + GPIO84_UART1_RTS, + + /* UART3 */ + GPIO110_UART3_RXD, + + /* USB Host */ + GPIO0_2_USBH_PEN, + GPIO1_2_USBH_PWR, + + /* I2C */ + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + + /* SPI */ + GPIO34_GPIO, /* SPDIF_CS */ + GPIO96_GPIO, /* MCLK_CS */ + GPIO125_GPIO, /* ACCEL_CS */ + + /* MMC */ + GPIO3_MMC1_DAT0, + GPIO4_MMC1_DAT1, + GPIO5_MMC1_DAT2, + GPIO6_MMC1_DAT3, + GPIO7_MMC1_CLK, + GPIO8_MMC1_CMD, + + /* Ethernet */ + GPIO1_nCS2, /* CS */ + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */ + + /* SSP for I2S */ + GPIO85_SSP1_SCLK, + GPIO89_SSP1_EXTCLK, + GPIO86_SSP1_FRM, + GPIO87_SSP1_TXD, + GPIO88_SSP1_RXD, + GPIO90_SSP1_SYSCLK, + + /* SSP2 for S/PDIF */ + GPIO25_SSP2_SCLK, + GPIO26_SSP2_FRM, + GPIO27_SSP2_TXD, + GPIO29_SSP2_EXTCLK, + + /* LEDs */ + GPIO35_GPIO | MFP_LPM_PULL_LOW, + GPIO36_GPIO | MFP_LPM_DRIVE_HIGH, +}; + +static mfp_cfg_t raumfeld_speaker_pin_config[] __initdata = { + /* UART1 */ + GPIO77_UART1_RXD, + GPIO78_UART1_TXD, + GPIO79_UART1_CTS, + GPIO81_UART1_DSR, + GPIO83_UART1_DTR, + GPIO84_UART1_RTS, + + /* UART3 */ + GPIO110_UART3_RXD, + + /* USB Host */ + GPIO0_2_USBH_PEN, + GPIO1_2_USBH_PWR, + + /* I2C */ + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT, + + /* SPI */ + GPIO34_GPIO, /* SPDIF_CS */ + GPIO96_GPIO, /* MCLK_CS */ + GPIO125_GPIO, /* ACCEL_CS */ + + /* MMC */ + GPIO3_MMC1_DAT0, + GPIO4_MMC1_DAT1, + GPIO5_MMC1_DAT2, + GPIO6_MMC1_DAT3, + GPIO7_MMC1_CLK, + GPIO8_MMC1_CMD, + + /* Ethernet */ + GPIO1_nCS2, /* CS */ + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */ + + /* SSP for I2S */ + GPIO85_SSP1_SCLK, + GPIO89_SSP1_EXTCLK, + GPIO86_SSP1_FRM, + GPIO87_SSP1_TXD, + GPIO88_SSP1_RXD, + GPIO90_SSP1_SYSCLK, + + /* LEDs */ + GPIO35_GPIO | MFP_LPM_PULL_LOW, + GPIO36_GPIO | MFP_LPM_DRIVE_HIGH, +}; + +/* + * SMSC LAN9220 Ethernet + */ + +static struct resource smc91x_resources[] = { + { + .start = PXA3xx_CS2_PHYS, + .end = PXA3xx_CS2_PHYS + 0xfffff, + .flags = IORESOURCE_MEM, + }, + { + .start = gpio_to_irq(GPIO_ETH_IRQ), + .end = gpio_to_irq(GPIO_ETH_IRQ), + .flags = IORESOURCE_IRQ | IRQF_TRIGGER_FALLING, + } +}; + +static struct smsc911x_platform_config raumfeld_smsc911x_config = { + .phy_interface = PHY_INTERFACE_MODE_MII, + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS, +}; + +static struct platform_device smc91x_device = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &raumfeld_smsc911x_config, + } +}; + +/** + * NAND + */ + +static struct mtd_partition raumfeld_nand_partitions[] = { + { + .name = "Bootloader", + .offset = 0, + .size = 0xa0000, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, + { + .name = "BootloaderEnvironment", + .offset = 0xa0000, + .size = 0x20000, + }, + { + .name = "BootloaderSplashScreen", + .offset = 0xc0000, + .size = 0x60000, + }, + { + .name = "UBI", + .offset = 0x120000, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct pxa3xx_nand_platform_data raumfeld_nand_info = { + .enable_arbiter = 1, + .keep_config = 1, + .parts = raumfeld_nand_partitions, + .nr_parts = ARRAY_SIZE(raumfeld_nand_partitions), +}; + +/** + * USB (OHCI) support + */ + +static struct pxaohci_platform_data raumfeld_ohci_info = { + .port_mode = PMM_GLOBAL_MODE, + .flags = ENABLE_PORT1, +}; + +/** + * Rotary encoder input device + */ + +static struct rotary_encoder_platform_data raumfeld_rotary_encoder_info = { + .steps = 24, + .axis = REL_X, + .relative_axis = 1, + .gpio_a = GPIO_VOLENC_A, + .gpio_b = GPIO_VOLENC_B, + .inverted_a = 1, + .inverted_b = 0, +}; + +static struct platform_device rotary_encoder_device = { + .name = "rotary-encoder", + .id = 0, + .dev = { + .platform_data = &raumfeld_rotary_encoder_info, + } +}; + +/** + * GPIO buttons + */ + +static struct gpio_keys_button gpio_keys_button[] = { + { + .code = KEY_F1, + .type = EV_KEY, + .gpio = GPIO_KEY1, + .active_low = 1, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "Button 1", + }, + { + .code = KEY_F2, + .type = EV_KEY, + .gpio = GPIO_KEY2, + .active_low = 1, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "Button 2", + }, + { + .code = KEY_F3, + .type = EV_KEY, + .gpio = GPIO_KEY3, + .active_low = 1, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "Button 3", + }, + { + .code = KEY_F4, + .type = EV_KEY, + .gpio = GPIO_RESCUE_BOOT, + .active_low = 0, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "rescue boot button", + }, + { + .code = KEY_F5, + .type = EV_KEY, + .gpio = GPIO_DOCK_DETECT, + .active_low = 1, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "dock detect", + }, + { + .code = KEY_F6, + .type = EV_KEY, + .gpio = GPIO_ON_OFF, + .active_low = 0, + .wakeup = 0, + .debounce_interval = 5, /* ms */ + .desc = "on/off button", + }, +}; + +static struct gpio_keys_platform_data gpio_keys_platform_data = { + .buttons = gpio_keys_button, + .nbuttons = ARRAY_SIZE(gpio_keys_button), + .rep = 0, +}; + +static struct platform_device raumfeld_gpio_keys_device = { + .name = "gpio-keys", + .id = -1, + .dev = { + .platform_data = &gpio_keys_platform_data, + } +}; + +/** + * GPIO LEDs + */ + +static struct gpio_led raumfeld_leds[] = { + { + .name = "raumfeld:1", + .gpio = GPIO_LED1, + .active_low = 1, + .default_state = LEDS_GPIO_DEFSTATE_ON, + }, + { + .name = "raumfeld:2", + .gpio = GPIO_LED2, + .active_low = 0, + .default_state = LEDS_GPIO_DEFSTATE_OFF, + } +}; + +static struct gpio_led_platform_data raumfeld_led_platform_data = { + .leds = raumfeld_leds, + .num_leds = ARRAY_SIZE(raumfeld_leds), +}; + +static struct platform_device raumfeld_led_device = { + .name = "leds-gpio", + .id = -1, + .dev = { + .platform_data = &raumfeld_led_platform_data, + }, +}; + +/** + * One-wire (W1 bus) support + */ + +static void w1_enable_external_pullup(int enable) +{ + gpio_set_value(GPIO_W1_PULLUP_ENABLE, enable); + msleep(100); +} + +static struct w1_gpio_platform_data w1_gpio_platform_data = { + .pin = GPIO_ONE_WIRE, + .is_open_drain = 0, + .enable_external_pullup = w1_enable_external_pullup, +}; + +struct platform_device raumfeld_w1_gpio_device = { + .name = "w1-gpio", + .dev = { + .platform_data = &w1_gpio_platform_data + } +}; + +static void __init raumfeld_w1_init(void) +{ + int ret = gpio_request(GPIO_W1_PULLUP_ENABLE, + "W1 external pullup enable"); + + if (ret < 0) + pr_warning("Unable to request GPIO_W1_PULLUP_ENABLE\n"); + else + gpio_direction_output(GPIO_W1_PULLUP_ENABLE, 0); + + platform_device_register(&raumfeld_w1_gpio_device); +} + +/** + * Framebuffer device + */ + +/* PWM controlled backlight */ +static struct platform_pwm_backlight_data raumfeld_pwm_backlight_data = { + .pwm_id = 0, + .max_brightness = 100, + .dft_brightness = 100, + /* 10000 ns = 10 ms ^= 100 kHz */ + .pwm_period_ns = 10000, +}; + +static struct platform_device raumfeld_pwm_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa27x_device_pwm0.dev, + .platform_data = &raumfeld_pwm_backlight_data, + } +}; + +/* LT3593 controlled backlight */ +static struct gpio_led raumfeld_lt3593_led = { + .name = "backlight", + .gpio = mfp_to_gpio(MFP_PIN_GPIO17), + .default_state = LEDS_GPIO_DEFSTATE_ON, +}; + +static struct gpio_led_platform_data raumfeld_lt3593_platform_data = { + .leds = &raumfeld_lt3593_led, + .num_leds = 1, +}; + +static struct platform_device raumfeld_lt3593_device = { + .name = "leds-lt3593", + .id = -1, + .dev = { + .platform_data = &raumfeld_lt3593_platform_data, + }, +}; + +static struct pxafb_mode_info sharp_lq043t3dx02_mode = { + .pixclock = 111000, + .xres = 480, + .yres = 272, + .bpp = 16, + .hsync_len = 4, + .left_margin = 2, + .right_margin = 1, + .vsync_len = 1, + .upper_margin = 3, + .lower_margin = 1, + .sync = 0, +}; + +static struct pxafb_mach_info raumfeld_sharp_lcd_info = { + .modes = &sharp_lq043t3dx02_mode, + .num_modes = 1, + .video_mem_size = 0x400000, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +static void __init raumfeld_lcd_init(void) +{ + int ret; + + set_pxa_fb_info(&raumfeld_sharp_lcd_info); + + /* Earlier devices had the backlight regulator controlled + * via PWM, later versions use another controller for that */ + if ((system_rev & 0xff) < 2) { + mfp_cfg_t raumfeld_pwm_pin_config = GPIO17_PWM0_OUT; + pxa3xx_mfp_config(&raumfeld_pwm_pin_config, 1); + platform_device_register(&raumfeld_pwm_backlight_device); + } else + platform_device_register(&raumfeld_lt3593_device); + + ret = gpio_request(GPIO_TFT_VA_EN, "display VA enable"); + if (ret < 0) + pr_warning("Unable to request GPIO_TFT_VA_EN\n"); + else + gpio_direction_output(GPIO_TFT_VA_EN, 1); + + ret = gpio_request(GPIO_DISPLAY_ENABLE, "display enable"); + if (ret < 0) + pr_warning("Unable to request GPIO_DISPLAY_ENABLE\n"); + else + gpio_direction_output(GPIO_DISPLAY_ENABLE, 1); +} + +/** + * SPI devices + */ + +struct spi_gpio_platform_data raumfeld_spi_platform_data = { + .sck = GPIO_SPI_CLK, + .mosi = GPIO_SPI_MOSI, + .miso = GPIO_SPI_MISO, + .num_chipselect = 3, +}; + +static struct platform_device raumfeld_spi_device = { + .name = "spi_gpio", + .id = 0, + .dev = { + .platform_data = &raumfeld_spi_platform_data, + } +}; + +static struct lis3lv02d_platform_data lis3_pdata = { + .click_flags = LIS3_CLICK_SINGLE_X | + LIS3_CLICK_SINGLE_Y | + LIS3_CLICK_SINGLE_Z, + .irq_cfg = LIS3_IRQ1_CLICK | LIS3_IRQ2_CLICK, + .wakeup_flags = LIS3_WAKEUP_X_LO | LIS3_WAKEUP_X_HI | + LIS3_WAKEUP_Y_LO | LIS3_WAKEUP_Y_HI | + LIS3_WAKEUP_Z_LO | LIS3_WAKEUP_Z_HI, + .wakeup_thresh = 10, + .click_thresh_x = 10, + .click_thresh_y = 10, + .click_thresh_z = 10, +}; + +#define SPI_AK4104 \ +{ \ + .modalias = "ak4104", \ + .max_speed_hz = 10000, \ + .bus_num = 0, \ + .chip_select = 0, \ + .controller_data = (void *) GPIO_SPDIF_CS, \ +} + +#define SPI_LIS3 \ +{ \ + .modalias = "lis3lv02d_spi", \ + .max_speed_hz = 1000000, \ + .bus_num = 0, \ + .chip_select = 1, \ + .controller_data = (void *) GPIO_ACCEL_CS, \ + .platform_data = &lis3_pdata, \ + .irq = gpio_to_irq(GPIO_ACCEL_IRQ), \ +} + +#define SPI_DAC7512 \ +{ \ + .modalias = "dac7512", \ + .max_speed_hz = 1000000, \ + .bus_num = 0, \ + .chip_select = 2, \ + .controller_data = (void *) GPIO_MCLK_DAC_CS, \ +} + +static struct spi_board_info connector_spi_devices[] __initdata = { + SPI_AK4104, + SPI_DAC7512, +}; + +static struct spi_board_info speaker_spi_devices[] __initdata = { + SPI_DAC7512, +}; + +static struct spi_board_info controller_spi_devices[] __initdata = { + SPI_LIS3, +}; + +/** + * MMC for Marvell Libertas 8688 via SDIO + */ + +static int raumfeld_mci_init(struct device *dev, irq_handler_t isr, void *data) +{ + gpio_set_value(GPIO_W2W_RESET, 1); + gpio_set_value(GPIO_W2W_PDN, 1); + + return 0; +} + +static void raumfeld_mci_exit(struct device *dev, void *data) +{ + gpio_set_value(GPIO_W2W_RESET, 0); + gpio_set_value(GPIO_W2W_PDN, 0); +} + +static struct pxamci_platform_data raumfeld_mci_platform_data = { + .init = raumfeld_mci_init, + .exit = raumfeld_mci_exit, + .detect_delay = 20, + .gpio_card_detect = -1, + .gpio_card_ro = -1, + .gpio_power = -1, +}; + +/* + * External power / charge logic + */ + +static int power_supply_init(struct device *dev) +{ + return 0; +} + +static void power_supply_exit(struct device *dev) +{ +} + +static int raumfeld_is_ac_online(void) +{ + return !gpio_get_value(GPIO_CHARGE_DC_OK); +} + +static int raumfeld_is_usb_online(void) +{ + return 0; +} + +static char *raumfeld_power_supplicants[] = { "ds2760-battery.0" }; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = raumfeld_is_ac_online, + .is_usb_online = raumfeld_is_usb_online, + .exit = power_supply_exit, + .supplied_to = raumfeld_power_supplicants, + .num_supplicants = ARRAY_SIZE(raumfeld_power_supplicants) +}; + +static struct resource power_supply_resources[] = { + { + .name = "ac", + .flags = IORESOURCE_IRQ | + IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE, + .start = GPIO_CHARGE_DC_OK, + .end = GPIO_CHARGE_DC_OK, + }, +}; + +static irqreturn_t charge_done_irq(int irq, void *dev_id) +{ + struct power_supply *psy; + + psy = power_supply_get_by_name("ds2760-battery.0"); + + if (psy) + power_supply_set_battery_charged(psy); + + return IRQ_HANDLED; +} + +static struct platform_device raumfeld_power_supply = { + .name = "pda-power", + .id = -1, + .dev = { + .platform_data = &power_supply_info, + }, + .resource = power_supply_resources, + .num_resources = ARRAY_SIZE(power_supply_resources), +}; + +static void __init raumfeld_power_init(void) +{ + int ret; + + /* Set PEN2 high to enable maximum charge current */ + ret = gpio_request(GPIO_CHRG_PEN2, "CHRG_PEN2"); + if (ret < 0) + pr_warning("Unable to request GPIO_CHRG_PEN2\n"); + else + gpio_direction_output(GPIO_CHRG_PEN2, 1); + + ret = gpio_request(GPIO_CHARGE_DC_OK, "CABLE_DC_OK"); + if (ret < 0) + pr_warning("Unable to request GPIO_CHARGE_DC_OK\n"); + + ret = gpio_request(GPIO_CHARGE_USB_SUSP, "CHARGE_USB_SUSP"); + if (ret < 0) + pr_warning("Unable to request GPIO_CHARGE_USB_SUSP\n"); + else + gpio_direction_output(GPIO_CHARGE_USB_SUSP, 0); + + power_supply_resources[0].start = gpio_to_irq(GPIO_CHARGE_DC_OK); + power_supply_resources[0].end = gpio_to_irq(GPIO_CHARGE_DC_OK); + + ret = request_irq(gpio_to_irq(GPIO_CHARGE_DONE), + &charge_done_irq, IORESOURCE_IRQ_LOWEDGE, + "charge_done", NULL); + + if (ret < 0) + printk(KERN_ERR "%s: unable to register irq %d\n", __func__, + GPIO_CHARGE_DONE); + else + platform_device_register(&raumfeld_power_supply); +} + +/* Fixed regulator for AUDIO_VA, 0-0048 maps to the cs4270 codec device */ + +static struct regulator_consumer_supply audio_va_consumer_supply = + REGULATOR_SUPPLY("va", "0-0048"); + +struct regulator_init_data audio_va_initdata = { + .consumer_supplies = &audio_va_consumer_supply, + .num_consumer_supplies = 1, + .constraints = { + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, +}; + +static struct fixed_voltage_config audio_va_config = { + .supply_name = "audio_va", + .microvolts = 5000000, + .gpio = GPIO_AUDIO_VA_ENABLE, + .enable_high = 1, + .enabled_at_boot = 0, + .init_data = &audio_va_initdata, +}; + +static struct platform_device audio_va_device = { + .name = "reg-fixed-voltage", + .id = 0, + .dev = { + .platform_data = &audio_va_config, + }, +}; + +/* Dummy supplies for Codec's VD/VLC */ + +static struct regulator_consumer_supply audio_dummy_supplies[] = { + REGULATOR_SUPPLY("vd", "0-0048"), + REGULATOR_SUPPLY("vlc", "0-0048"), +}; + +struct regulator_init_data audio_dummy_initdata = { + .consumer_supplies = audio_dummy_supplies, + .num_consumer_supplies = ARRAY_SIZE(audio_dummy_supplies), + .constraints = { + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, +}; + +static struct fixed_voltage_config audio_dummy_config = { + .supply_name = "audio_vd", + .microvolts = 3300000, + .gpio = -1, + .init_data = &audio_dummy_initdata, +}; + +static struct platform_device audio_supply_dummy_device = { + .name = "reg-fixed-voltage", + .id = 1, + .dev = { + .platform_data = &audio_dummy_config, + }, +}; + +static struct platform_device *audio_regulator_devices[] = { + &audio_va_device, + &audio_supply_dummy_device, +}; + +/** + * Regulator support via MAX8660 + */ + +static struct regulator_consumer_supply vcc_mmc_supply = + REGULATOR_SUPPLY("vmmc", "pxa2xx-mci.0"); + +static struct regulator_init_data vcc_mmc_init_data = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL, + .valid_ops_mask = REGULATOR_CHANGE_STATUS | + REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_MODE, + }, + .consumer_supplies = &vcc_mmc_supply, + .num_consumer_supplies = 1, +}; + +struct max8660_subdev_data max8660_v6_subdev_data = { + .id = MAX8660_V6, + .name = "vmmc", + .platform_data = &vcc_mmc_init_data, +}; + +static struct max8660_platform_data max8660_pdata = { + .subdevs = &max8660_v6_subdev_data, + .num_subdevs = 1, +}; + +/** + * I2C devices + */ + +static struct i2c_board_info raumfeld_pwri2c_board_info = { + .type = "max8660", + .addr = 0x34, + .platform_data = &max8660_pdata, +}; + +static struct i2c_board_info raumfeld_connector_i2c_board_info __initdata = { + .type = "cs4270", + .addr = 0x48, +}; + +static struct eeti_ts_platform_data eeti_ts_pdata = { + .irq_active_high = 1, +}; + +static struct i2c_board_info raumfeld_controller_i2c_board_info __initdata = { + .type = "eeti_ts", + .addr = 0x0a, + .irq = gpio_to_irq(GPIO_TOUCH_IRQ), + .platform_data = &eeti_ts_pdata, +}; + +static struct platform_device *raumfeld_common_devices[] = { + &raumfeld_gpio_keys_device, + &raumfeld_led_device, + &raumfeld_spi_device, +}; + +static void __init raumfeld_audio_init(void) +{ + int ret; + + ret = gpio_request(GPIO_CODEC_RESET, "cs4270 reset"); + if (ret < 0) + pr_warning("unable to request GPIO_CODEC_RESET\n"); + else + gpio_direction_output(GPIO_CODEC_RESET, 1); + + ret = gpio_request(GPIO_SPDIF_RESET, "ak4104 s/pdif reset"); + if (ret < 0) + pr_warning("unable to request GPIO_SPDIF_RESET\n"); + else + gpio_direction_output(GPIO_SPDIF_RESET, 1); + + ret = gpio_request(GPIO_MCLK_RESET, "MCLK reset"); + if (ret < 0) + pr_warning("unable to request GPIO_MCLK_RESET\n"); + else + gpio_direction_output(GPIO_MCLK_RESET, 1); + + platform_add_devices(ARRAY_AND_SIZE(audio_regulator_devices)); +} + +static void __init raumfeld_common_init(void) +{ + int ret; + + /* The on/off button polarity has changed after revision 1 */ + if ((system_rev & 0xff) > 1) { + int i; + + for (i = 0; i < ARRAY_SIZE(gpio_keys_button); i++) + if (!strcmp(gpio_keys_button[i].desc, "on/off button")) + gpio_keys_button[i].active_low = 1; + } + + enable_irq_wake(IRQ_WAKEUP0); + + pxa3xx_set_nand_info(&raumfeld_nand_info); + pxa3xx_set_i2c_power_info(NULL); + pxa_set_ohci_info(&raumfeld_ohci_info); + pxa_set_mci_info(&raumfeld_mci_platform_data); + pxa_set_i2c_info(NULL); + pxa_set_ffuart_info(NULL); + + ret = gpio_request(GPIO_W2W_RESET, "Wi2Wi reset"); + if (ret < 0) + pr_warning("Unable to request GPIO_W2W_RESET\n"); + else + gpio_direction_output(GPIO_W2W_RESET, 0); + + ret = gpio_request(GPIO_W2W_PDN, "Wi2Wi powerup"); + if (ret < 0) + pr_warning("Unable to request GPIO_W2W_PDN\n"); + else + gpio_direction_output(GPIO_W2W_PDN, 0); + + /* this can be used to switch off the device */ + ret = gpio_request(GPIO_SHUTDOWN_SUPPLY, + "supply shutdown"); + if (ret < 0) + pr_warning("Unable to request GPIO_SHUTDOWN_SUPPLY\n"); + else + gpio_direction_output(GPIO_SHUTDOWN_SUPPLY, 0); + + platform_add_devices(ARRAY_AND_SIZE(raumfeld_common_devices)); + i2c_register_board_info(1, &raumfeld_pwri2c_board_info, 1); +} + +static void __init raumfeld_controller_init(void) +{ + int ret; + + pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_controller_pin_config)); + platform_device_register(&rotary_encoder_device); + spi_register_board_info(ARRAY_AND_SIZE(controller_spi_devices)); + i2c_register_board_info(0, &raumfeld_controller_i2c_board_info, 1); + + ret = gpio_request(GPIO_SHUTDOWN_BATT, "battery shutdown"); + if (ret < 0) + pr_warning("Unable to request GPIO_SHUTDOWN_BATT\n"); + else + gpio_direction_output(GPIO_SHUTDOWN_BATT, 0); + + raumfeld_common_init(); + raumfeld_power_init(); + raumfeld_lcd_init(); + raumfeld_w1_init(); +} + +static void __init raumfeld_connector_init(void) +{ + pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_connector_pin_config)); + spi_register_board_info(ARRAY_AND_SIZE(connector_spi_devices)); + i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1); + + platform_device_register(&smc91x_device); + + raumfeld_audio_init(); + raumfeld_common_init(); +} + +static void __init raumfeld_speaker_init(void) +{ + pxa3xx_mfp_config(ARRAY_AND_SIZE(raumfeld_speaker_pin_config)); + spi_register_board_info(ARRAY_AND_SIZE(speaker_spi_devices)); + i2c_register_board_info(0, &raumfeld_connector_i2c_board_info, 1); + + platform_device_register(&smc91x_device); + platform_device_register(&rotary_encoder_device); + + raumfeld_audio_init(); + raumfeld_common_init(); +} + +/* physical memory regions */ +#define RAUMFELD_SDRAM_BASE 0xa0000000 /* SDRAM region */ + +#ifdef CONFIG_MACH_RAUMFELD_RC +MACHINE_START(RAUMFELD_RC, "Raumfeld Controller") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = RAUMFELD_SDRAM_BASE + 0x100, + .init_machine = raumfeld_controller_init, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_RAUMFELD_CONNECTOR +MACHINE_START(RAUMFELD_CONNECTOR, "Raumfeld Connector") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = RAUMFELD_SDRAM_BASE + 0x100, + .init_machine = raumfeld_connector_init, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, +MACHINE_END +#endif + +#ifdef CONFIG_MACH_RAUMFELD_SPEAKER +MACHINE_START(RAUMFELD_SPEAKER, "Raumfeld Speaker") + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = RAUMFELD_SDRAM_BASE + 0x100, + .init_machine = raumfeld_speaker_init, + .map_io = pxa_map_io, + .init_irq = pxa3xx_init_irq, + .timer = &pxa_timer, +MACHINE_END +#endif diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c index 67229a1ef55..463d874bb86 100644 --- a/arch/arm/mach-pxa/sharpsl_pm.c +++ b/arch/arm/mach-pxa/sharpsl_pm.c @@ -900,7 +900,7 @@ static struct platform_suspend_ops sharpsl_pm_ops = { }; #endif -static int __init sharpsl_pm_probe(struct platform_device *pdev) +static int __devinit sharpsl_pm_probe(struct platform_device *pdev) { int ret; diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c index 28352c0b8c3..19b5109d980 100644 --- a/arch/arm/mach-pxa/spitz.c +++ b/arch/arm/mach-pxa/spitz.c @@ -56,25 +56,7 @@ static unsigned long spitz_pin_config[] __initdata = { GPIO80_nCS_4, /* SCOOP #1 */ /* LCD - 16bpp Active TFT */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, + GPIOxx_LCD_TFT_16BPP, /* PC Card */ GPIO48_nPOE, diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c index 9ebe658590f..a81d6dbf662 100644 --- a/arch/arm/mach-pxa/ssp.c +++ b/arch/arm/mach-pxa/ssp.c @@ -35,6 +35,8 @@ #include <mach/ssp.h> #include <mach/regs-ssp.h> +#ifdef CONFIG_PXA_SSP_LEGACY + #define TIMEOUT 100000 static irqreturn_t ssp_interrupt(int irq, void *dev_id) @@ -303,6 +305,7 @@ void ssp_exit(struct ssp_dev *dev) clk_disable(ssp->clk); ssp_free(ssp); } +#endif /* CONFIG_PXA_SSP_LEGACY */ static DEFINE_MUTEX(ssp_lock); static LIST_HEAD(ssp_list); @@ -488,6 +491,7 @@ static void __exit pxa_ssp_exit(void) arch_initcall(pxa_ssp_init); module_exit(pxa_ssp_exit); +#ifdef CONFIG_PXA_SSP_LEGACY EXPORT_SYMBOL(ssp_write_word); EXPORT_SYMBOL(ssp_read_word); EXPORT_SYMBOL(ssp_flush); @@ -498,6 +502,7 @@ EXPORT_SYMBOL(ssp_restore_state); EXPORT_SYMBOL(ssp_init); EXPORT_SYMBOL(ssp_exit); EXPORT_SYMBOL(ssp_config); +#endif MODULE_DESCRIPTION("PXA SSP driver"); MODULE_AUTHOR("Liam Girdwood"); diff --git a/arch/arm/mach-pxa/time.c b/arch/arm/mach-pxa/time.c index 750c448db67..293e40aeaf2 100644 --- a/arch/arm/mach-pxa/time.c +++ b/arch/arm/mach-pxa/time.c @@ -76,14 +76,12 @@ pxa_ost0_interrupt(int irq, void *dev_id) static int pxa_osmr0_set_next_event(unsigned long delta, struct clock_event_device *dev) { - unsigned long flags, next, oscr; + unsigned long next, oscr; - raw_local_irq_save(flags); OIER |= OIER_E0; next = OSCR + delta; OSMR0 = next; oscr = OSCR; - raw_local_irq_restore(flags); return (signed)(next - oscr) <= MIN_OSCR_DELTA ? -ETIME : 0; } @@ -91,23 +89,17 @@ pxa_osmr0_set_next_event(unsigned long delta, struct clock_event_device *dev) static void pxa_osmr0_set_mode(enum clock_event_mode mode, struct clock_event_device *dev) { - unsigned long irqflags; - switch (mode) { case CLOCK_EVT_MODE_ONESHOT: - raw_local_irq_save(irqflags); OIER &= ~OIER_E0; OSSR = OSSR_M0; - raw_local_irq_restore(irqflags); break; case CLOCK_EVT_MODE_UNUSED: case CLOCK_EVT_MODE_SHUTDOWN: /* initializing, released, or preparing for suspend */ - raw_local_irq_save(irqflags); OIER &= ~OIER_E0; OSSR = OSSR_M0; - raw_local_irq_restore(irqflags); break; case CLOCK_EVT_MODE_RESUME: diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c index c854c168a45..ad552791c4c 100644 --- a/arch/arm/mach-pxa/tosa.c +++ b/arch/arm/mach-pxa/tosa.c @@ -32,6 +32,7 @@ #include <linux/gpio.h> #include <linux/pda_power.h> #include <linux/spi/spi.h> +#include <linux/input/matrix_keypad.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -131,24 +132,24 @@ static unsigned long tosa_pin_config[] = { GPIO45_BTUART_RTS, /* Keybd */ - GPIO58_GPIO | MFP_LPM_DRIVE_LOW, - GPIO59_GPIO | MFP_LPM_DRIVE_LOW, - GPIO60_GPIO | MFP_LPM_DRIVE_LOW, - GPIO61_GPIO | MFP_LPM_DRIVE_LOW, - GPIO62_GPIO | MFP_LPM_DRIVE_LOW, - GPIO63_GPIO | MFP_LPM_DRIVE_LOW, - GPIO64_GPIO | MFP_LPM_DRIVE_LOW, - GPIO65_GPIO | MFP_LPM_DRIVE_LOW, - GPIO66_GPIO | MFP_LPM_DRIVE_LOW, - GPIO67_GPIO | MFP_LPM_DRIVE_LOW, - GPIO68_GPIO | MFP_LPM_DRIVE_LOW, - GPIO69_GPIO | MFP_LPM_DRIVE_LOW, - GPIO70_GPIO | MFP_LPM_DRIVE_LOW, - GPIO71_GPIO | MFP_LPM_DRIVE_LOW, - GPIO72_GPIO | MFP_LPM_DRIVE_LOW, - GPIO73_GPIO | MFP_LPM_DRIVE_LOW, - GPIO74_GPIO | MFP_LPM_DRIVE_LOW, - GPIO75_GPIO | MFP_LPM_DRIVE_LOW, + GPIO58_GPIO | MFP_LPM_DRIVE_LOW, /* Column 0 */ + GPIO59_GPIO | MFP_LPM_DRIVE_LOW, /* Column 1 */ + GPIO60_GPIO | MFP_LPM_DRIVE_LOW, /* Column 2 */ + GPIO61_GPIO | MFP_LPM_DRIVE_LOW, /* Column 3 */ + GPIO62_GPIO | MFP_LPM_DRIVE_LOW, /* Column 4 */ + GPIO63_GPIO | MFP_LPM_DRIVE_LOW, /* Column 5 */ + GPIO64_GPIO | MFP_LPM_DRIVE_LOW, /* Column 6 */ + GPIO65_GPIO | MFP_LPM_DRIVE_LOW, /* Column 7 */ + GPIO66_GPIO | MFP_LPM_DRIVE_LOW, /* Column 8 */ + GPIO67_GPIO | MFP_LPM_DRIVE_LOW, /* Column 9 */ + GPIO68_GPIO | MFP_LPM_DRIVE_LOW, /* Column 10 */ + GPIO69_GPIO | MFP_LPM_DRIVE_LOW, /* Row 0 */ + GPIO70_GPIO | MFP_LPM_DRIVE_LOW, /* Row 1 */ + GPIO71_GPIO | MFP_LPM_DRIVE_LOW, /* Row 2 */ + GPIO72_GPIO | MFP_LPM_DRIVE_LOW, /* Row 3 */ + GPIO73_GPIO | MFP_LPM_DRIVE_LOW, /* Row 4 */ + GPIO74_GPIO | MFP_LPM_DRIVE_LOW, /* Row 5 */ + GPIO75_GPIO | MFP_LPM_DRIVE_LOW, /* Row 6 */ /* SPI */ GPIO81_SSP2_CLK_OUT, @@ -411,9 +412,87 @@ static struct platform_device tosa_power_device = { /* * Tosa Keyboard */ +static const uint32_t tosakbd_keymap[] = { + KEY(0, 2, KEY_W), + KEY(0, 6, KEY_K), + KEY(0, 7, KEY_BACKSPACE), + KEY(0, 8, KEY_P), + KEY(1, 1, KEY_Q), + KEY(1, 2, KEY_E), + KEY(1, 3, KEY_T), + KEY(1, 4, KEY_Y), + KEY(1, 6, KEY_O), + KEY(1, 7, KEY_I), + KEY(1, 8, KEY_COMMA), + KEY(2, 1, KEY_A), + KEY(2, 2, KEY_D), + KEY(2, 3, KEY_G), + KEY(2, 4, KEY_U), + KEY(2, 6, KEY_L), + KEY(2, 7, KEY_ENTER), + KEY(2, 8, KEY_DOT), + KEY(3, 1, KEY_Z), + KEY(3, 2, KEY_C), + KEY(3, 3, KEY_V), + KEY(3, 4, KEY_J), + KEY(3, 5, TOSA_KEY_ADDRESSBOOK), + KEY(3, 6, TOSA_KEY_CANCEL), + KEY(3, 7, TOSA_KEY_CENTER), + KEY(3, 8, TOSA_KEY_OK), + KEY(3, 9, KEY_LEFTSHIFT), + KEY(4, 1, KEY_S), + KEY(4, 2, KEY_R), + KEY(4, 3, KEY_B), + KEY(4, 4, KEY_N), + KEY(4, 5, TOSA_KEY_CALENDAR), + KEY(4, 6, TOSA_KEY_HOMEPAGE), + KEY(4, 7, KEY_LEFTCTRL), + KEY(4, 8, TOSA_KEY_LIGHT), + KEY(4, 10, KEY_RIGHTSHIFT), + KEY(5, 1, KEY_TAB), + KEY(5, 2, KEY_SLASH), + KEY(5, 3, KEY_H), + KEY(5, 4, KEY_M), + KEY(5, 5, TOSA_KEY_MENU), + KEY(5, 7, KEY_UP), + KEY(5, 11, TOSA_KEY_FN), + KEY(6, 1, KEY_X), + KEY(6, 2, KEY_F), + KEY(6, 3, KEY_SPACE), + KEY(6, 4, KEY_APOSTROPHE), + KEY(6, 5, TOSA_KEY_MAIL), + KEY(6, 6, KEY_LEFT), + KEY(6, 7, KEY_DOWN), + KEY(6, 8, KEY_RIGHT), +}; + +static struct matrix_keymap_data tosakbd_keymap_data = { + .keymap = tosakbd_keymap, + .keymap_size = ARRAY_SIZE(tosakbd_keymap), +}; + +static const int tosakbd_col_gpios[] = + { 58, 59, 60, 61, 62, 63, 64, 65, 66, 67, 68 }; +static const int tosakbd_row_gpios[] = + { 69, 70, 71, 72, 73, 74, 75 }; + +static struct matrix_keypad_platform_data tosakbd_pdata = { + .keymap_data = &tosakbd_keymap_data, + .row_gpios = tosakbd_row_gpios, + .col_gpios = tosakbd_col_gpios, + .num_row_gpios = ARRAY_SIZE(tosakbd_row_gpios), + .num_col_gpios = ARRAY_SIZE(tosakbd_col_gpios), + .col_scan_delay_us = 10, + .debounce_ms = 10, + .wakeup = 1, +}; + static struct platform_device tosakbd_device = { - .name = "tosa-keyboard", + .name = "matrix-keypad", .id = -1, + .dev = { + .platform_data = &tosakbd_pdata, + }, }; static struct gpio_keys_button tosa_gpio_keys[] = { diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c index 0aa858ebc57..797f2544d0c 100644 --- a/arch/arm/mach-pxa/trizeps4.c +++ b/arch/arm/mach-pxa/trizeps4.c @@ -72,27 +72,14 @@ static unsigned long trizeps4_pin_config[] __initdata = { GPIO79_nCS_3, /* Logic CS */ GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, /* Logic irq */ + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + /* LCD - 16bpp Active TFT */ - GPIO58_LCD_LDD_0, - GPIO59_LCD_LDD_1, - GPIO60_LCD_LDD_2, - GPIO61_LCD_LDD_3, - GPIO62_LCD_LDD_4, - GPIO63_LCD_LDD_5, - GPIO64_LCD_LDD_6, - GPIO65_LCD_LDD_7, - GPIO66_LCD_LDD_8, - GPIO67_LCD_LDD_9, - GPIO68_LCD_LDD_10, - GPIO69_LCD_LDD_11, - GPIO70_LCD_LDD_12, - GPIO71_LCD_LDD_13, - GPIO72_LCD_LDD_14, - GPIO73_LCD_LDD_15, - GPIO74_LCD_FCLK, - GPIO75_LCD_LCLK, - GPIO76_LCD_PCLK, - GPIO77_LCD_BIAS, + GPIOxx_LCD_TFT_16BPP, /* UART */ GPIO9_FFUART_CTS, diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c index 89f258c9e12..1dd13346f97 100644 --- a/arch/arm/mach-pxa/viper.c +++ b/arch/arm/mach-pxa/viper.c @@ -281,7 +281,7 @@ static void viper_irq_handler(unsigned int irq, struct irq_desc *desc) do { /* we're in a chained irq handler, * so ack the interrupt by hand */ - GEDR(VIPER_CPLD_GPIO) = GPIO_bit(VIPER_CPLD_GPIO); + desc->chip->ack(irq); if (likely(pending)) { irq = viper_bit_to_irq(__ffs(pending)); @@ -711,6 +711,12 @@ static mfp_cfg_t viper_pin_config[] __initdata = { GPIO80_nCS_4, GPIO33_nCS_5, + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + /* FP Backlight */ GPIO9_GPIO, /* VIPER_BCKLIGHT_EN_GPIO */ GPIO10_GPIO, /* VIPER_LCD_EN_GPIO */ diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c index 75f2a37f945..39896d88358 100644 --- a/arch/arm/mach-pxa/zeus.c +++ b/arch/arm/mach-pxa/zeus.c @@ -26,6 +26,7 @@ #include <linux/i2c.h> #include <linux/i2c/pca953x.h> #include <linux/apm-emulation.h> +#include <linux/can/platform/mcp251x.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -387,11 +388,47 @@ static struct pxa2xx_spi_master pxa2xx_spi_ssp3_master_info = { .enable_dma = 1, }; -static struct platform_device pxa2xx_spi_ssp3_device = { - .name = "pxa2xx-spi", - .id = 3, - .dev = { - .platform_data = &pxa2xx_spi_ssp3_master_info, +/* CAN bus on SPI */ +static int zeus_mcp2515_setup(struct spi_device *sdev) +{ + int err; + + err = gpio_request(ZEUS_CAN_SHDN_GPIO, "CAN shutdown"); + if (err) + return err; + + err = gpio_direction_output(ZEUS_CAN_SHDN_GPIO, 1); + if (err) { + gpio_free(ZEUS_CAN_SHDN_GPIO); + return err; + } + + return 0; +} + +static int zeus_mcp2515_transceiver_enable(int enable) +{ + gpio_set_value(ZEUS_CAN_SHDN_GPIO, !enable); + return 0; +} + +static struct mcp251x_platform_data zeus_mcp2515_pdata = { + .oscillator_frequency = 16*1000*1000, + .model = CAN_MCP251X_MCP2515, + .board_specific_setup = zeus_mcp2515_setup, + .transceiver_enable = zeus_mcp2515_transceiver_enable, + .power_enable = zeus_mcp2515_transceiver_enable, +}; + +static struct spi_board_info zeus_spi_board_info[] = { + [0] = { + .modalias = "mcp251x", + .platform_data = &zeus_mcp2515_pdata, + .irq = gpio_to_irq(ZEUS_CAN_GPIO), + .max_speed_hz = 1*1000*1000, + .bus_num = 3, + .mode = SPI_MODE_0, + .chip_select = 0, }, }; @@ -457,15 +494,28 @@ static struct platform_device zeus_pcmcia_device = { }, }; +static struct resource zeus_max6369_resource = { + .start = ZEUS_CPLD_EXTWDOG_PHYS, + .end = ZEUS_CPLD_EXTWDOG_PHYS, + .flags = IORESOURCE_MEM, +}; + +struct platform_device zeus_max6369_device = { + .name = "max6369_wdt", + .id = -1, + .resource = &zeus_max6369_resource, + .num_resources = 1, +}; + static struct platform_device *zeus_devices[] __initdata = { &zeus_serial_device, &zeus_mtd_devices[0], &zeus_dm9k0_device, &zeus_dm9k1_device, &zeus_sram_device, - &pxa2xx_spi_ssp3_device, &zeus_leds_device, &zeus_pcmcia_device, + &zeus_max6369_device, }; /* AC'97 */ @@ -509,7 +559,9 @@ static void zeus_ohci_exit(struct device *dev) static struct pxaohci_platform_data zeus_ohci_platform_data = { .port_mode = PMM_NPS_MODE, - .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW, + /* Clear Power Control Polarity Low and set Power Sense + * Polarity Low. Supply power to USB ports. */ + .flags = ENABLE_PORT_ALL | POWER_SENSE_LOW, .init = zeus_ohci_init, .exit = zeus_ohci_exit, }; @@ -621,11 +673,15 @@ static struct pxa2xx_udc_mach_info zeus_udc_info = { .udc_command = zeus_udc_command, }; +#ifdef CONFIG_PM static void zeus_power_off(void) { local_irq_disable(); pxa27x_cpu_suspend(PWRMODE_DEEPSLEEP); } +#else +#define zeus_power_off NULL +#endif #ifdef CONFIG_APM_EMULATION static void zeus_get_power_status(struct apm_power_info *info) @@ -706,6 +762,12 @@ static struct i2c_board_info __initdata zeus_i2c_devices[] = { }; static mfp_cfg_t zeus_pin_config[] __initdata = { + /* AC97 */ + GPIO28_AC97_BITCLK, + GPIO29_AC97_SDATA_IN_0, + GPIO30_AC97_SDATA_OUT, + GPIO31_AC97_SYNC, + GPIO15_nCS_1, GPIO78_nCS_2, GPIO80_nCS_4, @@ -731,6 +793,11 @@ static mfp_cfg_t zeus_pin_config[] __initdata = { GPIO104_CIF_DD_2, GPIO105_CIF_DD_1, + GPIO81_SSP3_TXD, + GPIO82_SSP3_RXD, + GPIO83_SSP3_SFRM, + GPIO84_SSP3_SCLK, + GPIO48_nPOE, GPIO49_nPWE, GPIO50_nPIOR, @@ -785,6 +852,8 @@ static void __init zeus_init(void) pxa_set_ac97_info(&zeus_ac97_info); pxa_set_i2c_info(NULL); i2c_register_board_info(0, ARRAY_AND_SIZE(zeus_i2c_devices)); + pxa2xx_set_spi_info(3, &pxa2xx_spi_ssp3_master_info); + spi_register_board_info(zeus_spi_board_info, ARRAY_SIZE(zeus_spi_board_info)); } static struct map_desc zeus_io_desc[] __initdata = { @@ -807,12 +876,6 @@ static struct map_desc zeus_io_desc[] __initdata = { .type = MT_DEVICE, }, { - .virtual = ZEUS_CPLD_EXTWDOG, - .pfn = __phys_to_pfn(ZEUS_CPLD_EXTWDOG_PHYS), - .length = 0x1000, - .type = MT_DEVICE, - }, - { .virtual = ZEUS_PC104IO, .pfn = __phys_to_pfn(ZEUS_PC104IO_PHYS), .length = 0x00800000, @@ -837,7 +900,7 @@ static void __init zeus_map_io(void) PCFR = PCFR_OPDE | PCFR_DC_EN | PCFR_FS | PCFR_FP; } -MACHINE_START(ARCOM_ZEUS, "Arcom ZEUS") +MACHINE_START(ARCOM_ZEUS, "Arcom/Eurotech ZEUS") /* Maintainer: Marc Zyngier <maz@misterjones.org> */ .phys_io = 0x40000000, .io_pg_offst = ((io_p2v(0x40000000) >> 18) & 0xfffc), |