diff options
Diffstat (limited to 'arch/arm/mach-realview')
| -rw-r--r-- | arch/arm/mach-realview/Makefile | 3 | ||||
| -rw-r--r-- | arch/arm/mach-realview/core.c | 233 | ||||
| -rw-r--r-- | arch/arm/mach-realview/core.h | 2 | ||||
| -rw-r--r-- | arch/arm/mach-realview/headsmp.S | 40 | ||||
| -rw-r--r-- | arch/arm/mach-realview/include/mach/barriers.h | 2 | ||||
| -rw-r--r-- | arch/arm/mach-realview/localtimer.c | 26 | ||||
| -rw-r--r-- | arch/arm/mach-realview/platsmp.c | 98 | ||||
| -rw-r--r-- | arch/arm/mach-realview/realview_eb.c | 24 | ||||
| -rw-r--r-- | arch/arm/mach-realview/realview_pb1176.c | 22 | ||||
| -rw-r--r-- | arch/arm/mach-realview/realview_pb11mp.c | 22 | ||||
| -rw-r--r-- | arch/arm/mach-realview/realview_pba8.c | 22 | ||||
| -rw-r--r-- | arch/arm/mach-realview/realview_pbx.c | 22 |
12 files changed, 52 insertions, 464 deletions
diff --git a/arch/arm/mach-realview/Makefile b/arch/arm/mach-realview/Makefile index a01b76b7c95..541fa4c109e 100644 --- a/arch/arm/mach-realview/Makefile +++ b/arch/arm/mach-realview/Makefile @@ -8,6 +8,5 @@ obj-$(CONFIG_MACH_REALVIEW_PB11MP) += realview_pb11mp.o obj-$(CONFIG_MACH_REALVIEW_PB1176) += realview_pb1176.o obj-$(CONFIG_MACH_REALVIEW_PBA8) += realview_pba8.o obj-$(CONFIG_MACH_REALVIEW_PBX) += realview_pbx.o -obj-$(CONFIG_SMP) += platsmp.o headsmp.o +obj-$(CONFIG_SMP) += platsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o -obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o diff --git a/arch/arm/mach-realview/core.c b/arch/arm/mach-realview/core.c index 1c6602cf50e..75dbc8791d0 100644 --- a/arch/arm/mach-realview/core.c +++ b/arch/arm/mach-realview/core.c @@ -51,6 +51,7 @@ #include <mach/irqs.h> #include <asm/hardware/timer-sp.h> +#include <plat/clcd.h> #include <plat/sched_clock.h> #include "core.h" @@ -359,18 +360,19 @@ static struct clk_lookup lookups[] = { } }; -static int __init clk_init(void) +void __init realview_init_early(void) { + void __iomem *sys = __io_address(REALVIEW_SYS_BASE); + if (machine_is_realview_pb1176()) - oscvco_clk.vcoreg = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_OSC0_OFFSET; + oscvco_clk.vcoreg = sys + REALVIEW_SYS_OSC0_OFFSET; else - oscvco_clk.vcoreg = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_OSC4_OFFSET; + oscvco_clk.vcoreg = sys + REALVIEW_SYS_OSC4_OFFSET; clkdev_add_table(lookups, ARRAY_SIZE(lookups)); - return 0; + versatile_sched_clock_init(sys + REALVIEW_SYS_24MHz_OFFSET, 24000000); } -core_initcall(clk_init); /* * CLCD support. @@ -385,157 +387,6 @@ core_initcall(clk_init); #define SYS_CLCD_ID_SANYO_2_5 (0x07 << 8) #define SYS_CLCD_ID_VGA (0x1f << 8) -static struct clcd_panel vga = { - .mode = { - .name = "VGA", - .refresh = 60, - .xres = 640, - .yres = 480, - .pixclock = 39721, - .left_margin = 40, - .right_margin = 24, - .upper_margin = 32, - .lower_margin = 11, - .hsync_len = 96, - .vsync_len = 2, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, - .width = -1, - .height = -1, - .tim2 = TIM2_BCD | TIM2_IPC, - .cntl = CNTL_LCDTFT | CNTL_BGR | CNTL_LCDVCOMP(1), - .bpp = 16, -}; - -static struct clcd_panel xvga = { - .mode = { - .name = "XVGA", - .refresh = 60, - .xres = 1024, - .yres = 768, - .pixclock = 15748, - .left_margin = 152, - .right_margin = 48, - .upper_margin = 23, - .lower_margin = 3, - .hsync_len = 104, - .vsync_len = 4, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, - .width = -1, - .height = -1, - .tim2 = TIM2_BCD | TIM2_IPC, - .cntl = CNTL_LCDTFT | CNTL_BGR | CNTL_LCDVCOMP(1), - .bpp = 16, -}; - -static struct clcd_panel sanyo_3_8_in = { - .mode = { - .name = "Sanyo QVGA", - .refresh = 116, - .xres = 320, - .yres = 240, - .pixclock = 100000, - .left_margin = 6, - .right_margin = 6, - .upper_margin = 5, - .lower_margin = 5, - .hsync_len = 6, - .vsync_len = 6, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, - .width = -1, - .height = -1, - .tim2 = TIM2_BCD, - .cntl = CNTL_LCDTFT | CNTL_BGR | CNTL_LCDVCOMP(1), - .bpp = 16, -}; - -static struct clcd_panel sanyo_2_5_in = { - .mode = { - .name = "Sanyo QVGA Portrait", - .refresh = 116, - .xres = 240, - .yres = 320, - .pixclock = 100000, - .left_margin = 20, - .right_margin = 10, - .upper_margin = 2, - .lower_margin = 2, - .hsync_len = 10, - .vsync_len = 2, - .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, - .vmode = FB_VMODE_NONINTERLACED, - }, - .width = -1, - .height = -1, - .tim2 = TIM2_IVS | TIM2_IHS | TIM2_IPC, - .cntl = CNTL_LCDTFT | CNTL_BGR | CNTL_LCDVCOMP(1), - .bpp = 16, -}; - -static struct clcd_panel epson_2_2_in = { - .mode = { - .name = "Epson QCIF", - .refresh = 390, - .xres = 176, - .yres = 220, - .pixclock = 62500, - .left_margin = 3, - .right_margin = 2, - .upper_margin = 1, - .lower_margin = 0, - .hsync_len = 3, - .vsync_len = 2, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED, - }, - .width = -1, - .height = -1, - .tim2 = TIM2_BCD | TIM2_IPC, - .cntl = CNTL_LCDTFT | CNTL_BGR | CNTL_LCDVCOMP(1), - .bpp = 16, -}; - -/* - * Detect which LCD panel is connected, and return the appropriate - * clcd_panel structure. Note: we do not have any information on - * the required timings for the 8.4in panel, so we presently assume - * VGA timings. - */ -static struct clcd_panel *realview_clcd_panel(void) -{ - void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET; - struct clcd_panel *vga_panel; - struct clcd_panel *panel; - u32 val; - - if (machine_is_realview_eb()) - vga_panel = &vga; - else - vga_panel = &xvga; - - val = readl(sys_clcd) & SYS_CLCD_ID_MASK; - if (val == SYS_CLCD_ID_SANYO_3_8) - panel = &sanyo_3_8_in; - else if (val == SYS_CLCD_ID_SANYO_2_5) - panel = &sanyo_2_5_in; - else if (val == SYS_CLCD_ID_EPSON_2_2) - panel = &epson_2_2_in; - else if (val == SYS_CLCD_ID_VGA) - panel = vga_panel; - else { - printk(KERN_ERR "CLCD: unknown LCD panel ID 0x%08x, using VGA\n", - val); - panel = vga_panel; - } - - return panel; -} - /* * Disable all display connectors on the interface module. */ @@ -565,56 +416,60 @@ static void realview_clcd_enable(struct clcd_fb *fb) writel(val, sys_clcd); } +/* + * Detect which LCD panel is connected, and return the appropriate + * clcd_panel structure. Note: we do not have any information on + * the required timings for the 8.4in panel, so we presently assume + * VGA timings. + */ static int realview_clcd_setup(struct clcd_fb *fb) { + void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET; + const char *panel_name, *vga_panel_name; unsigned long framesize; - dma_addr_t dma; + u32 val; - if (machine_is_realview_eb()) + if (machine_is_realview_eb()) { /* VGA, 16bpp */ framesize = 640 * 480 * 2; - else + vga_panel_name = "VGA"; + } else { /* XVGA, 16bpp */ framesize = 1024 * 768 * 2; - - fb->panel = realview_clcd_panel(); - - fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize, - &dma, GFP_KERNEL | GFP_DMA); - if (!fb->fb.screen_base) { - printk(KERN_ERR "CLCD: unable to map framebuffer\n"); - return -ENOMEM; + vga_panel_name = "XVGA"; } - fb->fb.fix.smem_start = dma; - fb->fb.fix.smem_len = framesize; - - return 0; -} + val = readl(sys_clcd) & SYS_CLCD_ID_MASK; + if (val == SYS_CLCD_ID_SANYO_3_8) + panel_name = "Sanyo TM38QV67A02A"; + else if (val == SYS_CLCD_ID_SANYO_2_5) + panel_name = "Sanyo QVGA Portrait"; + else if (val == SYS_CLCD_ID_EPSON_2_2) + panel_name = "Epson L2F50113T00"; + else if (val == SYS_CLCD_ID_VGA) + panel_name = vga_panel_name; + else { + pr_err("CLCD: unknown LCD panel ID 0x%08x, using VGA\n", val); + panel_name = vga_panel_name; + } -static int realview_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma) -{ - return dma_mmap_writecombine(&fb->dev->dev, vma, - fb->fb.screen_base, - fb->fb.fix.smem_start, - fb->fb.fix.smem_len); -} + fb->panel = versatile_clcd_get_panel(panel_name); + if (!fb->panel) + return -EINVAL; -static void realview_clcd_remove(struct clcd_fb *fb) -{ - dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len, - fb->fb.screen_base, fb->fb.fix.smem_start); + return versatile_clcd_setup_dma(fb, framesize); } struct clcd_board clcd_plat_data = { .name = "RealView", + .caps = CLCD_CAP_ALL, .check = clcdfb_check, .decode = clcdfb_decode, .disable = realview_clcd_disable, .enable = realview_clcd_enable, .setup = realview_clcd_setup, - .mmap = realview_clcd_mmap, - .remove = realview_clcd_remove, + .mmap = versatile_clcd_mmap_dma, + .remove = versatile_clcd_remove_dma, }; #ifdef CONFIG_LEDS @@ -656,12 +511,6 @@ void realview_leds_event(led_event_t ledevt) #endif /* CONFIG_LEDS */ /* - * The sched_clock counter - */ -#define REFCOUNTER (__io_address(REALVIEW_SYS_BASE) + \ - REALVIEW_SYS_24MHz_OFFSET) - -/* * Where is the timer (VA)? */ void __iomem *timer0_va_base; @@ -676,8 +525,6 @@ void __init realview_timer_init(unsigned int timer_irq) { u32 val; - versatile_sched_clock_init(REFCOUNTER, 24000000); - /* * set clock frequency: * REALVIEW_REFCLK is 32KHz diff --git a/arch/arm/mach-realview/core.h b/arch/arm/mach-realview/core.h index 693239ddc39..5c83d1e87a0 100644 --- a/arch/arm/mach-realview/core.h +++ b/arch/arm/mach-realview/core.h @@ -42,7 +42,6 @@ static struct amba_device name##_device = { \ }, \ .dma_mask = ~0, \ .irq = base##_IRQ, \ - /* .dma = base##_DMA,*/ \ } struct machine_desc; @@ -63,6 +62,7 @@ extern void realview_timer_init(unsigned int timer_irq); extern int realview_flash_register(struct resource *res, u32 num); extern int realview_eth_register(const char *name, struct resource *res); extern int realview_usb_register(struct resource *res); +extern void realview_init_early(void); extern void realview_fixup(struct machine_desc *mdesc, struct tag *tags, char **from, struct meminfo *meminfo); extern void (*realview_reset)(char); diff --git a/arch/arm/mach-realview/headsmp.S b/arch/arm/mach-realview/headsmp.S deleted file mode 100644 index b34be4554d4..00000000000 --- a/arch/arm/mach-realview/headsmp.S +++ /dev/null @@ -1,40 +0,0 @@ -/* - * linux/arch/arm/mach-realview/headsmp.S - * - * Copyright (c) 2003 ARM Limited - * All Rights Reserved - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/linkage.h> -#include <linux/init.h> - - __INIT - -/* - * Realview specific entry point for secondary CPUs. This provides - * a "holding pen" into which all secondary cores are held until we're - * ready for them to initialise. - */ -ENTRY(realview_secondary_startup) - mrc p15, 0, r0, c0, c0, 5 - and r0, r0, #15 - adr r4, 1f - ldmia r4, {r5, r6} - sub r4, r4, r5 - add r6, r6, r4 -pen: ldr r7, [r6] - cmp r7, r0 - bne pen - - /* - * we've been released from the holding pen: secondary_stack - * should now contain the SVC stack for this core - */ - b secondary_startup - - .align -1: .long . - .long pen_release diff --git a/arch/arm/mach-realview/include/mach/barriers.h b/arch/arm/mach-realview/include/mach/barriers.h index 0c5d749d7b5..9a732195aa1 100644 --- a/arch/arm/mach-realview/include/mach/barriers.h +++ b/arch/arm/mach-realview/include/mach/barriers.h @@ -4,5 +4,5 @@ * operation to deadlock the system. */ #define mb() dsb() -#define rmb() dmb() +#define rmb() dsb() #define wmb() mb() diff --git a/arch/arm/mach-realview/localtimer.c b/arch/arm/mach-realview/localtimer.c deleted file mode 100644 index 60b4e111f45..00000000000 --- a/arch/arm/mach-realview/localtimer.c +++ /dev/null @@ -1,26 +0,0 @@ -/* - * linux/arch/arm/mach-realview/localtimer.c - * - * Copyright (C) 2002 ARM Ltd. - * All Rights Reserved - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -#include <linux/init.h> -#include <linux/smp.h> -#include <linux/clockchips.h> - -#include <asm/irq.h> -#include <asm/smp_twd.h> -#include <asm/localtimer.h> - -/* - * Setup the local clock events for a CPU. - */ -void __cpuinit local_timer_setup(struct clock_event_device *evt) -{ - evt->irq = IRQ_LOCALTIMER; - twd_timer_setup(evt); -} diff --git a/arch/arm/mach-realview/platsmp.c b/arch/arm/mach-realview/platsmp.c index 6959d13d908..23919229e12 100644 --- a/arch/arm/mach-realview/platsmp.c +++ b/arch/arm/mach-realview/platsmp.c @@ -10,44 +10,21 @@ */ #include <linux/init.h> #include <linux/errno.h> -#include <linux/delay.h> -#include <linux/device.h> -#include <linux/jiffies.h> #include <linux/smp.h> #include <linux/io.h> -#include <asm/cacheflush.h> #include <mach/hardware.h> #include <asm/mach-types.h> +#include <asm/smp_scu.h> #include <asm/unified.h> #include <mach/board-eb.h> #include <mach/board-pb11mp.h> #include <mach/board-pbx.h> -#include <asm/smp_scu.h> #include "core.h" -extern void realview_secondary_startup(void); - -/* - * control for which core is the next to come out of the secondary - * boot "holding pen" - */ -volatile int __cpuinitdata pen_release = -1; - -/* - * Write pen_release in a way that is guaranteed to be visible to all - * observers, irrespective of whether they're taking part in coherency - * or not. This is necessary for the hotplug code to work reliably. - */ -static void __cpuinit write_pen_release(int val) -{ - pen_release = val; - smp_wmb(); - __cpuc_flush_dcache_area((void *)&pen_release, sizeof(pen_release)); - outer_clean_range(__pa(&pen_release), __pa(&pen_release + 1)); -} +extern void versatile_secondary_startup(void); static void __iomem *scu_base_addr(void) { @@ -62,75 +39,6 @@ static void __iomem *scu_base_addr(void) return (void __iomem *)0; } -static DEFINE_SPINLOCK(boot_lock); - -void __cpuinit platform_secondary_init(unsigned int cpu) -{ - /* - * if any interrupts are already enabled for the primary - * core (e.g. timer irq), then they will not have been enabled - * for us: do so - */ - gic_secondary_init(0); - - /* - * let the primary processor know we're out of the - * pen, then head off into the C entry point - */ - write_pen_release(-1); - - /* - * Synchronise with the boot thread. - */ - spin_lock(&boot_lock); - spin_unlock(&boot_lock); -} - -int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) -{ - unsigned long timeout; - - /* - * set synchronisation state between this boot processor - * and the secondary one - */ - spin_lock(&boot_lock); - - /* - * The secondary processor is waiting to be released from - * the holding pen - release it, then wait for it to flag - * that it has been released by resetting pen_release. - * - * Note that "pen_release" is the hardware CPU ID, whereas - * "cpu" is Linux's internal ID. - */ - write_pen_release(cpu); - - /* - * Send the secondary CPU a soft interrupt, thereby causing - * the boot monitor to read the system wide flags register, - * and branch to the address found there. - */ - smp_cross_call(cpumask_of(cpu), 1); - - timeout = jiffies + (1 * HZ); - while (time_before(jiffies, timeout)) { - smp_rmb(); - if (pen_release == -1) - break; - - udelay(10); - } - - /* - * now the secondary core is starting up let it run its - * calibrations, then wait for it to finish - */ - spin_unlock(&boot_lock); - - return pen_release != -1 ? -ENOSYS : 0; -} - /* * Initialise the CPU possible map early - this describes the CPUs * which may be present or become present in the system. @@ -174,6 +82,6 @@ void __init platform_smp_prepare_cpus(unsigned int max_cpus) * until it receives a soft interrupt, and then the * secondary CPU branches to this address. */ - __raw_writel(BSYM(virt_to_phys(realview_secondary_startup)), + __raw_writel(BSYM(virt_to_phys(versatile_secondary_startup)), __io_address(REALVIEW_SYS_FLAGSSET)); } diff --git a/arch/arm/mach-realview/realview_eb.c b/arch/arm/mach-realview/realview_eb.c index 8ede983b861..10e75faba4c 100644 --- a/arch/arm/mach-realview/realview_eb.c +++ b/arch/arm/mach-realview/realview_eb.c @@ -144,60 +144,39 @@ static struct pl022_ssp_controller ssp0_plat_data = { * These devices are connected via the core APB bridge */ #define GPIO2_IRQ { IRQ_EB_GPIO2, NO_IRQ } -#define GPIO2_DMA { 0, 0 } #define GPIO3_IRQ { IRQ_EB_GPIO3, NO_IRQ } -#define GPIO3_DMA { 0, 0 } #define AACI_IRQ { IRQ_EB_AACI, NO_IRQ } -#define AACI_DMA { 0x80, 0x81 } #define MMCI0_IRQ { IRQ_EB_MMCI0A, IRQ_EB_MMCI0B } -#define MMCI0_DMA { 0x84, 0 } #define KMI0_IRQ { IRQ_EB_KMI0, NO_IRQ } -#define KMI0_DMA { 0, 0 } #define KMI1_IRQ { IRQ_EB_KMI1, NO_IRQ } -#define KMI1_DMA { 0, 0 } /* * These devices are connected directly to the multi-layer AHB switch */ #define EB_SMC_IRQ { NO_IRQ, NO_IRQ } -#define EB_SMC_DMA { 0, 0 } #define MPMC_IRQ { NO_IRQ, NO_IRQ } -#define MPMC_DMA { 0, 0 } #define EB_CLCD_IRQ { IRQ_EB_CLCD, NO_IRQ } -#define EB_CLCD_DMA { 0, 0 } #define DMAC_IRQ { IRQ_EB_DMA, NO_IRQ } -#define DMAC_DMA { 0, 0 } /* * These devices are connected via the core APB bridge */ #define SCTL_IRQ { NO_IRQ, NO_IRQ } -#define SCTL_DMA { 0, 0 } #define EB_WATCHDOG_IRQ { IRQ_EB_WDOG, NO_IRQ } -#define EB_WATCHDOG_DMA { 0, 0 } #define EB_GPIO0_IRQ { IRQ_EB_GPIO0, NO_IRQ } -#define EB_GPIO0_DMA { 0, 0 } #define GPIO1_IRQ { IRQ_EB_GPIO1, NO_IRQ } -#define GPIO1_DMA { 0, 0 } #define EB_RTC_IRQ { IRQ_EB_RTC, NO_IRQ } -#define EB_RTC_DMA { 0, 0 } /* * These devices are connected via the DMA APB bridge */ #define SCI_IRQ { IRQ_EB_SCI, NO_IRQ } -#define SCI_DMA { 7, 6 } #define EB_UART0_IRQ { IRQ_EB_UART0, NO_IRQ } -#define EB_UART0_DMA { 15, 14 } #define EB_UART1_IRQ { IRQ_EB_UART1, NO_IRQ } -#define EB_UART1_DMA { 13, 12 } #define EB_UART2_IRQ { IRQ_EB_UART2, NO_IRQ } -#define EB_UART2_DMA { 11, 10 } #define EB_UART3_IRQ { IRQ_EB_UART3, NO_IRQ } -#define EB_UART3_DMA { 0x86, 0x87 } #define EB_SSP_IRQ { IRQ_EB_SSP, NO_IRQ } -#define EB_SSP_DMA { 9, 8 } /* FPGA Primecells */ AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL); @@ -369,7 +348,7 @@ static void __init gic_init_irq(void) #ifndef CONFIG_REALVIEW_EB_ARM11MP_REVB /* board GIC, secondary */ - gic_init(1, 64, __io_address(REALVIEW_EB_GIC_DIST_BASE), + gic_init(1, 96, __io_address(REALVIEW_EB_GIC_DIST_BASE), __io_address(REALVIEW_EB_GIC_CPU_BASE)); gic_cascade_irq(1, IRQ_EB11MP_EB_IRQ1); #endif @@ -487,6 +466,7 @@ MACHINE_START(REALVIEW_EB, "ARM-RealView EB") .boot_params = PLAT_PHYS_OFFSET + 0x00000100, .fixup = realview_fixup, .map_io = realview_eb_map_io, + .init_early = realview_init_early, .init_irq = gic_init_irq, .timer = &realview_eb_timer, .init_machine = realview_eb_init, diff --git a/arch/arm/mach-realview/realview_pb1176.c b/arch/arm/mach-realview/realview_pb1176.c index 9f26369555c..eab6070f66d 100644 --- a/arch/arm/mach-realview/realview_pb1176.c +++ b/arch/arm/mach-realview/realview_pb1176.c @@ -134,47 +134,26 @@ static struct pl022_ssp_controller ssp0_plat_data = { * RealView PB1176 AMBA devices */ #define GPIO2_IRQ { IRQ_PB1176_GPIO2, NO_IRQ } -#define GPIO2_DMA { 0, 0 } #define GPIO3_IRQ { IRQ_PB1176_GPIO3, NO_IRQ } -#define GPIO3_DMA { 0, 0 } #define AACI_IRQ { IRQ_PB1176_AACI, NO_IRQ } -#define AACI_DMA { 0x80, 0x81 } #define MMCI0_IRQ { IRQ_PB1176_MMCI0A, IRQ_PB1176_MMCI0B } -#define MMCI0_DMA { 0x84, 0 } #define KMI0_IRQ { IRQ_PB1176_KMI0, NO_IRQ } -#define KMI0_DMA { 0, 0 } #define KMI1_IRQ { IRQ_PB1176_KMI1, NO_IRQ } -#define KMI1_DMA { 0, 0 } #define PB1176_SMC_IRQ { NO_IRQ, NO_IRQ } -#define PB1176_SMC_DMA { 0, 0 } #define MPMC_IRQ { NO_IRQ, NO_IRQ } -#define MPMC_DMA { 0, 0 } #define PB1176_CLCD_IRQ { IRQ_DC1176_CLCD, NO_IRQ } -#define PB1176_CLCD_DMA { 0, 0 } #define SCTL_IRQ { NO_IRQ, NO_IRQ } -#define SCTL_DMA { 0, 0 } #define PB1176_WATCHDOG_IRQ { IRQ_DC1176_WATCHDOG, NO_IRQ } -#define PB1176_WATCHDOG_DMA { 0, 0 } #define PB1176_GPIO0_IRQ { IRQ_PB1176_GPIO0, NO_IRQ } -#define PB1176_GPIO0_DMA { 0, 0 } #define GPIO1_IRQ { IRQ_PB1176_GPIO1, NO_IRQ } -#define GPIO1_DMA { 0, 0 } #define PB1176_RTC_IRQ { IRQ_DC1176_RTC, NO_IRQ } -#define PB1176_RTC_DMA { 0, 0 } #define SCI_IRQ { IRQ_PB1176_SCI, NO_IRQ } -#define SCI_DMA { 7, 6 } #define PB1176_UART0_IRQ { IRQ_DC1176_UART0, NO_IRQ } -#define PB1176_UART0_DMA { 15, 14 } #define PB1176_UART1_IRQ { IRQ_DC1176_UART1, NO_IRQ } -#define PB1176_UART1_DMA { 13, 12 } #define PB1176_UART2_IRQ { IRQ_DC1176_UART2, NO_IRQ } -#define PB1176_UART2_DMA { 11, 10 } #define PB1176_UART3_IRQ { IRQ_DC1176_UART3, NO_IRQ } -#define PB1176_UART3_DMA { 0x86, 0x87 } #define PB1176_UART4_IRQ { IRQ_PB1176_UART4, NO_IRQ } -#define PB1176_UART4_DMA { 0, 0 } #define PB1176_SSP_IRQ { IRQ_DC1176_SSP, NO_IRQ } -#define PB1176_SSP_DMA { 9, 8 } /* FPGA Primecells */ AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL); @@ -382,6 +361,7 @@ MACHINE_START(REALVIEW_PB1176, "ARM-RealView PB1176") .boot_params = PLAT_PHYS_OFFSET + 0x00000100, .fixup = realview_pb1176_fixup, .map_io = realview_pb1176_map_io, + .init_early = realview_init_early, .init_irq = gic_init_irq, .timer = &realview_pb1176_timer, .init_machine = realview_pb1176_init, diff --git a/arch/arm/mach-realview/realview_pb11mp.c b/arch/arm/mach-realview/realview_pb11mp.c index dea06b2da3a..b2985fc7cd4 100644 --- a/arch/arm/mach-realview/realview_pb11mp.c +++ b/arch/arm/mach-realview/realview_pb11mp.c @@ -136,47 +136,26 @@ static struct pl022_ssp_controller ssp0_plat_data = { */ #define GPIO2_IRQ { IRQ_PB11MP_GPIO2, NO_IRQ } -#define GPIO2_DMA { 0, 0 } #define GPIO3_IRQ { IRQ_PB11MP_GPIO3, NO_IRQ } -#define GPIO3_DMA { 0, 0 } #define AACI_IRQ { IRQ_TC11MP_AACI, NO_IRQ } -#define AACI_DMA { 0x80, 0x81 } #define MMCI0_IRQ { IRQ_TC11MP_MMCI0A, IRQ_TC11MP_MMCI0B } -#define MMCI0_DMA { 0x84, 0 } #define KMI0_IRQ { IRQ_TC11MP_KMI0, NO_IRQ } -#define KMI0_DMA { 0, 0 } #define KMI1_IRQ { IRQ_TC11MP_KMI1, NO_IRQ } -#define KMI1_DMA { 0, 0 } #define PB11MP_SMC_IRQ { NO_IRQ, NO_IRQ } -#define PB11MP_SMC_DMA { 0, 0 } #define MPMC_IRQ { NO_IRQ, NO_IRQ } -#define MPMC_DMA { 0, 0 } #define PB11MP_CLCD_IRQ { IRQ_PB11MP_CLCD, NO_IRQ } -#define PB11MP_CLCD_DMA { 0, 0 } #define DMAC_IRQ { IRQ_PB11MP_DMAC, NO_IRQ } -#define DMAC_DMA { 0, 0 } #define SCTL_IRQ { NO_IRQ, NO_IRQ } -#define SCTL_DMA { 0, 0 } #define PB11MP_WATCHDOG_IRQ { IRQ_PB11MP_WATCHDOG, NO_IRQ } -#define PB11MP_WATCHDOG_DMA { 0, 0 } #define PB11MP_GPIO0_IRQ { IRQ_PB11MP_GPIO0, NO_IRQ } -#define PB11MP_GPIO0_DMA { 0, 0 } #define GPIO1_IRQ { IRQ_PB11MP_GPIO1, NO_IRQ } -#define GPIO1_DMA { 0, 0 } #define PB11MP_RTC_IRQ { IRQ_TC11MP_RTC, NO_IRQ } -#define PB11MP_RTC_DMA { 0, 0 } #define SCI_IRQ { IRQ_PB11MP_SCI, NO_IRQ } -#define SCI_DMA { 7, 6 } #define PB11MP_UART0_IRQ { IRQ_TC11MP_UART0, NO_IRQ } -#define PB11MP_UART0_DMA { 15, 14 } #define PB11MP_UART1_IRQ { IRQ_TC11MP_UART1, NO_IRQ } -#define PB11MP_UART1_DMA { 13, 12 } #define PB11MP_UART2_IRQ { IRQ_PB11MP_UART2, NO_IRQ } -#define PB11MP_UART2_DMA { 11, 10 } #define PB11MP_UART3_IRQ { IRQ_PB11MP_UART3, NO_IRQ } -#define PB11MP_UART3_DMA { 0x86, 0x87 } #define PB11MP_SSP_IRQ { IRQ_PB11MP_SSP, NO_IRQ } -#define PB11MP_SSP_DMA { 9, 8 } /* FPGA Primecells */ AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL); @@ -384,6 +363,7 @@ MACHINE_START(REALVIEW_PB11MP, "ARM-RealView PB11MPCore") .boot_params = PLAT_PHYS_OFFSET + 0x00000100, .fixup = realview_fixup, .map_io = realview_pb11mp_map_io, + .init_early = realview_init_early, .init_irq = gic_init_irq, .timer = &realview_pb11mp_timer, .init_machine = realview_pb11mp_init, diff --git a/arch/arm/mach-realview/realview_pba8.c b/arch/arm/mach-realview/realview_pba8.c index 7d0f1734a21..fb686655876 100644 --- a/arch/arm/mach-realview/realview_pba8.c +++ b/arch/arm/mach-realview/realview_pba8.c @@ -126,47 +126,26 @@ static struct pl022_ssp_controller ssp0_plat_data = { */ #define GPIO2_IRQ { IRQ_PBA8_GPIO2, NO_IRQ } -#define GPIO2_DMA { 0, 0 } #define GPIO3_IRQ { IRQ_PBA8_GPIO3, NO_IRQ } -#define GPIO3_DMA { 0, 0 } #define AACI_IRQ { IRQ_PBA8_AACI, NO_IRQ } -#define AACI_DMA { 0x80, 0x81 } #define MMCI0_IRQ { IRQ_PBA8_MMCI0A, IRQ_PBA8_MMCI0B } -#define MMCI0_DMA { 0x84, 0 } #define KMI0_IRQ { IRQ_PBA8_KMI0, NO_IRQ } -#define KMI0_DMA { 0, 0 } #define KMI1_IRQ { IRQ_PBA8_KMI1, NO_IRQ } -#define KMI1_DMA { 0, 0 } #define PBA8_SMC_IRQ { NO_IRQ, NO_IRQ } -#define PBA8_SMC_DMA { 0, 0 } #define MPMC_IRQ { NO_IRQ, NO_IRQ } -#define MPMC_DMA { 0, 0 } #define PBA8_CLCD_IRQ { IRQ_PBA8_CLCD, NO_IRQ } -#define PBA8_CLCD_DMA { 0, 0 } #define DMAC_IRQ { IRQ_PBA8_DMAC, NO_IRQ } -#define DMAC_DMA { 0, 0 } #define SCTL_IRQ { NO_IRQ, NO_IRQ } -#define SCTL_DMA { 0, 0 } #define PBA8_WATCHDOG_IRQ { IRQ_PBA8_WATCHDOG, NO_IRQ } -#define PBA8_WATCHDOG_DMA { 0, 0 } #define PBA8_GPIO0_IRQ { IRQ_PBA8_GPIO0, NO_IRQ } -#define PBA8_GPIO0_DMA { 0, 0 } #define GPIO1_IRQ { IRQ_PBA8_GPIO1, NO_IRQ } -#define GPIO1_DMA { 0, 0 } #define PBA8_RTC_IRQ { IRQ_PBA8_RTC, NO_IRQ } -#define PBA8_RTC_DMA { 0, 0 } #define SCI_IRQ { IRQ_PBA8_SCI, NO_IRQ } -#define SCI_DMA { 7, 6 } #define PBA8_UART0_IRQ { IRQ_PBA8_UART0, NO_IRQ } -#define PBA8_UART0_DMA { 15, 14 } #define PBA8_UART1_IRQ { IRQ_PBA8_UART1, NO_IRQ } -#define PBA8_UART1_DMA { 13, 12 } #define PBA8_UART2_IRQ { IRQ_PBA8_UART2, NO_IRQ } -#define PBA8_UART2_DMA { 11, 10 } #define PBA8_UART3_IRQ { IRQ_PBA8_UART3, NO_IRQ } -#define PBA8_UART3_DMA { 0x86, 0x87 } #define PBA8_SSP_IRQ { IRQ_PBA8_SSP, NO_IRQ } -#define PBA8_SSP_DMA { 9, 8 } /* FPGA Primecells */ AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL); @@ -334,6 +313,7 @@ MACHINE_START(REALVIEW_PBA8, "ARM-RealView PB-A8") .boot_params = PLAT_PHYS_OFFSET + 0x00000100, .fixup = realview_fixup, .map_io = realview_pba8_map_io, + .init_early = realview_init_early, .init_irq = gic_init_irq, .timer = &realview_pba8_timer, .init_machine = realview_pba8_init, diff --git a/arch/arm/mach-realview/realview_pbx.c b/arch/arm/mach-realview/realview_pbx.c index b89e28f8853..92ace2cf2b2 100644 --- a/arch/arm/mach-realview/realview_pbx.c +++ b/arch/arm/mach-realview/realview_pbx.c @@ -148,47 +148,26 @@ static struct pl022_ssp_controller ssp0_plat_data = { */ #define GPIO2_IRQ { IRQ_PBX_GPIO2, NO_IRQ } -#define GPIO2_DMA { 0, 0 } #define GPIO3_IRQ { IRQ_PBX_GPIO3, NO_IRQ } -#define GPIO3_DMA { 0, 0 } #define AACI_IRQ { IRQ_PBX_AACI, NO_IRQ } -#define AACI_DMA { 0x80, 0x81 } #define MMCI0_IRQ { IRQ_PBX_MMCI0A, IRQ_PBX_MMCI0B } -#define MMCI0_DMA { 0x84, 0 } #define KMI0_IRQ { IRQ_PBX_KMI0, NO_IRQ } -#define KMI0_DMA { 0, 0 } #define KMI1_IRQ { IRQ_PBX_KMI1, NO_IRQ } -#define KMI1_DMA { 0, 0 } #define PBX_SMC_IRQ { NO_IRQ, NO_IRQ } -#define PBX_SMC_DMA { 0, 0 } #define MPMC_IRQ { NO_IRQ, NO_IRQ } -#define MPMC_DMA { 0, 0 } #define PBX_CLCD_IRQ { IRQ_PBX_CLCD, NO_IRQ } -#define PBX_CLCD_DMA { 0, 0 } #define DMAC_IRQ { IRQ_PBX_DMAC, NO_IRQ } -#define DMAC_DMA { 0, 0 } #define SCTL_IRQ { NO_IRQ, NO_IRQ } -#define SCTL_DMA { 0, 0 } #define PBX_WATCHDOG_IRQ { IRQ_PBX_WATCHDOG, NO_IRQ } -#define PBX_WATCHDOG_DMA { 0, 0 } #define PBX_GPIO0_IRQ { IRQ_PBX_GPIO0, NO_IRQ } -#define PBX_GPIO0_DMA { 0, 0 } #define GPIO1_IRQ { IRQ_PBX_GPIO1, NO_IRQ } -#define GPIO1_DMA { 0, 0 } #define PBX_RTC_IRQ { IRQ_PBX_RTC, NO_IRQ } -#define PBX_RTC_DMA { 0, 0 } #define SCI_IRQ { IRQ_PBX_SCI, NO_IRQ } -#define SCI_DMA { 7, 6 } #define PBX_UART0_IRQ { IRQ_PBX_UART0, NO_IRQ } -#define PBX_UART0_DMA { 15, 14 } #define PBX_UART1_IRQ { IRQ_PBX_UART1, NO_IRQ } -#define PBX_UART1_DMA { 13, 12 } #define PBX_UART2_IRQ { IRQ_PBX_UART2, NO_IRQ } -#define PBX_UART2_DMA { 11, 10 } #define PBX_UART3_IRQ { IRQ_PBX_UART3, NO_IRQ } -#define PBX_UART3_DMA { 0x86, 0x87 } #define PBX_SSP_IRQ { IRQ_PBX_SSP, NO_IRQ } -#define PBX_SSP_DMA { 9, 8 } /* FPGA Primecells */ AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL); @@ -417,6 +396,7 @@ MACHINE_START(REALVIEW_PBX, "ARM-RealView PBX") .boot_params = PLAT_PHYS_OFFSET + 0x00000100, .fixup = realview_pbx_fixup, .map_io = realview_pbx_map_io, + .init_early = realview_init_early, .init_irq = gic_init_irq, .timer = &realview_pbx_timer, .init_machine = realview_pbx_init, |