diff options
Diffstat (limited to 'arch/arm/mach-s3c2410')
28 files changed, 419 insertions, 169 deletions
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 554731868b0..7245a55795d 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -6,6 +6,7 @@ config CPU_S3C2410 bool depends on ARCH_S3C2410 select CPU_ARM920T + select S3C_GPIO_PULL_UP select S3C2410_CLOCK select S3C2410_GPIO select CPU_LLSERIAL_S3C2410 @@ -76,6 +77,7 @@ config ARCH_H1940 select PM_H1940 if PM select S3C_DEV_USB_HOST select S3C_DEV_NAND + select S3C2410_SETUP_TS help Say Y here if you are using the HP IPAQ H1940 @@ -95,12 +97,19 @@ config PM_H1940 config MACH_N30 bool "Acer N30 family" select CPU_S3C2410 + select MACH_N35 select S3C_DEV_USB_HOST select S3C_DEV_NAND help Say Y here if you want suppt for the Acer N30, Acer N35, Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs. +config MACH_N35 + bool + help + Internal node in order to enable support for Acer N35 if Acer N30 is + selected. + config ARCH_BAST bool "Simtec Electronics BAST (EB2410ITX)" select CPU_S3C2410 @@ -110,6 +119,7 @@ config ARCH_BAST select MACH_BAST_IDE select S3C24XX_DCLK select ISA + select S3C_DEV_HWMON select S3C_DEV_USB_HOST select S3C_DEV_NAND help diff --git a/arch/arm/mach-s3c2410/Makefile.boot b/arch/arm/mach-s3c2410/Makefile.boot index 7dab2a0325b..58c1dd7f8e1 100644 --- a/arch/arm/mach-s3c2410/Makefile.boot +++ b/arch/arm/mach-s3c2410/Makefile.boot @@ -1,3 +1,7 @@ - zreladdr-y := 0x30008000 -params_phys-y := 0x30000100 - +ifeq ($(CONFIG_PM_H1940),y) + zreladdr-y := 0x30108000 + params_phys-y := 0x30100100 +else + zreladdr-y := 0x30008000 + params_phys-y := 0x30000100 +endif diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c index a3f3c7b1ca3..8cdeb14af59 100644 --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c @@ -33,14 +33,15 @@ static void h1940bt_enable(int on) h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER); /* Reset the chip */ mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 1); + + gpio_set_value(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 0); + gpio_set_value(S3C2410_GPH(1), 0); } else { - s3c2410_gpio_setpin(S3C2410_GPH(1), 1); + gpio_set_value(S3C2410_GPH(1), 1); mdelay(10); - s3c2410_gpio_setpin(S3C2410_GPH(1), 0); + gpio_set_value(S3C2410_GPH(1), 0); mdelay(10); h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0); } @@ -61,15 +62,21 @@ static int __devinit h1940bt_probe(struct platform_device *pdev) struct rfkill *rfk; int ret = 0; + ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev)); + if (ret) { + dev_err(&pdev->dev, "could not get GPH1\n");\ + return ret; + } + /* Configures BT serial port GPIOs */ - s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); - s3c2410_gpio_pullup(S3C2410_GPH(0), 1); - s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_pullup(S3C2410_GPH(1), 1); - s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0); - s3c2410_gpio_pullup(S3C2410_GPH(2), 1); - s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0); - s3c2410_gpio_pullup(S3C2410_GPH(3), 1); + s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0); + s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE); + s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT); + s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE); + s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0); + s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE); + s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0); + s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE); rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH, @@ -100,6 +107,7 @@ static int h1940bt_remove(struct platform_device *pdev) struct rfkill *rfk = platform_get_drvdata(pdev); platform_set_drvdata(pdev, NULL); + gpio_free(S3C2410_GPH(1)); if (rfk) { rfkill_unregister(rfk); diff --git a/arch/arm/mach-s3c2410/include/mach/dma.h b/arch/arm/mach-s3c2410/include/mach/dma.h index 08ac5f96c01..cf68136cc66 100644 --- a/arch/arm/mach-s3c2410/include/mach/dma.h +++ b/arch/arm/mach-s3c2410/include/mach/dma.h @@ -54,7 +54,7 @@ enum dma_ch { #define DMACH_LOW_LEVEL (1<<28) /* use this to specifiy hardware ch no */ /* we have 4 dma channels */ -#ifndef CONFIG_CPU_S3C2443 +#if !defined(CONFIG_CPU_S3C2443) && !defined(CONFIG_CPU_S3C2416) #define S3C_DMA_CHANNELS (4) #else #define S3C_DMA_CHANNELS (6) diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h index 035a493952d..f453c4f2cb8 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-fns.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-fns.h @@ -10,14 +10,28 @@ * published by the Free Software Foundation. */ +#ifndef __MACH_GPIO_FNS_H +#define __MACH_GPIO_FNS_H __FILE__ + /* These functions are in the to-be-removed category and it is strongly * encouraged not to use these in new code. They will be marked deprecated * very soon. * * Most of the functionality can be either replaced by the gpiocfg calls * for the s3c platform or by the generic GPIOlib API. + * + * As of 2.6.35-rc, these will be removed, with the few drivers using them + * either replaced or given a wrapper until the calls can be removed. */ +#include <plat/gpio-cfg.h> + +static inline void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int cfg) +{ + /* 1:1 mapping between cfgpin and setcfg calls at the moment */ + s3c_gpio_cfgpin(pin, cfg); +} + /* external functions for GPIO support * * These allow various different clients to access the same GPIO @@ -25,17 +39,6 @@ * GPIO register, then it is safe to ioremap/__raw_{read|write} to it. */ -/* s3c2410_gpio_cfgpin - * - * set the configuration of the given pin to the value passed. - * - * eg: - * s3c2410_gpio_cfgpin(S3C2410_GPA(0), S3C2410_GPA0_ADDR0); - * s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1); -*/ - -extern void s3c2410_gpio_cfgpin(unsigned int pin, unsigned int function); - extern unsigned int s3c2410_gpio_getcfg(unsigned int pin); /* s3c2410_gpio_getirq @@ -73,6 +76,14 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, /* s3c2410_gpio_pullup * + * This call should be replaced with s3c_gpio_setpull(). + * + * As a note, there is currently no distinction between pull-up and pull-down + * in the s3c24xx series devices with only an on/off configuration. + */ + +/* s3c2410_gpio_pullup + * * configure the pull-up control on the given pin * * to = 1 => disable the pull-up @@ -86,18 +97,8 @@ extern int s3c2410_gpio_irqfilter(unsigned int pin, unsigned int on, extern void s3c2410_gpio_pullup(unsigned int pin, unsigned int to); -/* s3c2410_gpio_getpull - * - * Read the state of the pull-up on a given pin - * - * return: - * < 0 => error code - * 0 => enabled - * 1 => disabled -*/ - -extern int s3c2410_gpio_getpull(unsigned int pin); - extern void s3c2410_gpio_setpin(unsigned int pin, unsigned int to); extern unsigned int s3c2410_gpio_getpin(unsigned int pin); + +#endif /* __MACH_GPIO_FNS_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h index 2edbb9c88ab..4f7bf3272e8 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-nrs.h @@ -16,15 +16,28 @@ #define S3C2410_GPIONO(bank,offset) ((bank) + (offset)) -#define S3C2410_GPIO_BANKA (32*0) -#define S3C2410_GPIO_BANKB (32*1) -#define S3C2410_GPIO_BANKC (32*2) -#define S3C2410_GPIO_BANKD (32*3) -#define S3C2410_GPIO_BANKE (32*4) -#define S3C2410_GPIO_BANKF (32*5) #define S3C2410_GPIO_BANKG (32*6) #define S3C2410_GPIO_BANKH (32*7) +/* GPIO sizes for various SoCs: + * + * 2442 + * 2410 2412 2440 2443 2416 + * ---- ---- ---- ---- ---- + * A 23 22 25 16 25 + * B 11 11 11 11 9 + * C 16 15 16 16 16 + * D 16 16 16 16 16 + * E 16 16 16 16 16 + * F 8 8 8 8 8 + * G 16 16 16 16 8 + * H 11 11 9 15 15 + * J -- -- 13 16 -- + * K -- -- -- -- 16 + * L -- -- -- 15 7 + * M -- -- -- 2 2 + */ + /* GPIO bank sizes */ #define S3C2410_GPIO_A_NR (32) #define S3C2410_GPIO_B_NR (32) @@ -34,6 +47,10 @@ #define S3C2410_GPIO_F_NR (32) #define S3C2410_GPIO_G_NR (32) #define S3C2410_GPIO_H_NR (32) +#define S3C2410_GPIO_J_NR (32) /* technically 16. */ +#define S3C2410_GPIO_K_NR (32) /* technically 16. */ +#define S3C2410_GPIO_L_NR (32) /* technically 15. */ +#define S3C2410_GPIO_M_NR (32) /* technically 2. */ #if CONFIG_S3C_GPIO_SPACE != 0 #error CONFIG_S3C_GPIO_SPACE cannot be zero at the moment @@ -53,6 +70,10 @@ enum s3c_gpio_number { S3C2410_GPIO_F_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_E), S3C2410_GPIO_G_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_F), S3C2410_GPIO_H_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_G), + S3C2410_GPIO_J_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_H), + S3C2410_GPIO_K_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_J), + S3C2410_GPIO_L_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_K), + S3C2410_GPIO_M_START = S3C2410_GPIO_NEXT(S3C2410_GPIO_L), }; #endif /* __ASSEMBLY__ */ @@ -67,6 +88,10 @@ enum s3c_gpio_number { #define S3C2410_GPF(_nr) (S3C2410_GPIO_F_START + (_nr)) #define S3C2410_GPG(_nr) (S3C2410_GPIO_G_START + (_nr)) #define S3C2410_GPH(_nr) (S3C2410_GPIO_H_START + (_nr)) +#define S3C2410_GPJ(_nr) (S3C2410_GPIO_J_START + (_nr)) +#define S3C2410_GPK(_nr) (S3C2410_GPIO_K_START + (_nr)) +#define S3C2410_GPL(_nr) (S3C2410_GPIO_L_START + (_nr)) +#define S3C2410_GPM(_nr) (S3C2410_GPIO_M_START + (_nr)) /* compatibility until drivers can be modified */ diff --git a/arch/arm/mach-s3c2410/include/mach/gpio-track.h b/arch/arm/mach-s3c2410/include/mach/gpio-track.h index acb25910380..d67819dde42 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio-track.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio-track.h @@ -23,11 +23,11 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin) { struct s3c_gpio_chip *chip; - if (pin > S3C2410_GPG(10)) + if (pin > S3C_GPIO_END) return NULL; chip = &s3c24xx_gpios[pin/32]; - return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL; + return ((pin - chip->chip.base) < chip->chip.ngpio) ? chip : NULL; } #endif /* __ASM_ARCH_GPIO_CORE_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/gpio.h b/arch/arm/mach-s3c2410/include/mach/gpio.h index 15f0b3e7ce6..b649bf2ccd5 100644 --- a/arch/arm/mach-s3c2410/include/mach/gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/gpio.h @@ -20,10 +20,18 @@ * devices that need GPIO. */ +#ifdef CONFIG_CPU_S3C244X +#define ARCH_NR_GPIOS (32 * 9 + CONFIG_S3C24XX_GPIO_EXTRA) +#else #define ARCH_NR_GPIOS (256 + CONFIG_S3C24XX_GPIO_EXTRA) +#endif #include <asm-generic/gpio.h> #include <mach/gpio-nrs.h> #include <mach/gpio-fns.h> +#ifdef CONFIG_CPU_S3C24XX +#define S3C_GPIO_END (S3C2410_GPIO_BANKJ + 32) +#else #define S3C_GPIO_END (S3C2410_GPIO_BANKH + 32) +#endif diff --git a/arch/arm/mach-s3c2410/include/mach/irqs.h b/arch/arm/mach-s3c2410/include/mach/irqs.h index 6c12c6312ad..11bb0f08fe6 100644 --- a/arch/arm/mach-s3c2410/include/mach/irqs.h +++ b/arch/arm/mach-s3c2410/include/mach/irqs.h @@ -115,6 +115,26 @@ #define IRQ_S3C2412_SDI S3C2410_IRQSUB(13) #define IRQ_S3C2412_CF S3C2410_IRQSUB(14) + +#define IRQ_S3C2416_EINT8t15 S3C2410_IRQ(5) +#define IRQ_S3C2416_DMA S3C2410_IRQ(17) +#define IRQ_S3C2416_UART3 S3C2410_IRQ(18) +#define IRQ_S3C2416_SDI1 S3C2410_IRQ(20) +#define IRQ_S3C2416_SDI0 S3C2410_IRQ(21) + +#define IRQ_S3C2416_LCD2 S3C2410_IRQSUB(15) +#define IRQ_S3C2416_LCD3 S3C2410_IRQSUB(16) +#define IRQ_S3C2416_LCD4 S3C2410_IRQSUB(17) +#define IRQ_S3C2416_DMA0 S3C2410_IRQSUB(18) +#define IRQ_S3C2416_DMA1 S3C2410_IRQSUB(19) +#define IRQ_S3C2416_DMA2 S3C2410_IRQSUB(20) +#define IRQ_S3C2416_DMA3 S3C2410_IRQSUB(21) +#define IRQ_S3C2416_DMA4 S3C2410_IRQSUB(22) +#define IRQ_S3C2416_DMA5 S3C2410_IRQSUB(23) +#define IRQ_S32416_WDT S3C2410_IRQSUB(27) +#define IRQ_S32416_AC97 S3C2410_IRQSUB(28) + + /* extra irqs for s3c2440 */ #define IRQ_S3C2440_CAM_C S3C2410_IRQSUB(11) /* S3C2443 too */ @@ -130,7 +150,10 @@ #define IRQ_S3C2443_HSMMC S3C2410_IRQ(20) /* IRQ_SDI */ #define IRQ_S3C2443_NAND S3C2410_IRQ(24) /* reserved */ +#define IRQ_S3C2416_HSMMC0 S3C2410_IRQ(21) /* S3C2416/S3C2450 */ + #define IRQ_HSMMC0 IRQ_S3C2443_HSMMC +#define IRQ_HSMMC1 IRQ_S3C2416_HSMMC0 #define IRQ_S3C2443_LCD1 S3C2410_IRQSUB(14) #define IRQ_S3C2443_LCD2 S3C2410_IRQSUB(15) @@ -152,7 +175,7 @@ #define IRQ_S3C2443_WDT S3C2410_IRQSUB(27) #define IRQ_S3C2443_AC97 S3C2410_IRQSUB(28) -#ifdef CONFIG_CPU_S3C2443 +#if defined(CONFIG_CPU_S3C2443) || defined(CONFIG_CPU_S3C2416) #define NR_IRQS (IRQ_S3C2443_AC97+1) #else #define NR_IRQS (IRQ_S3C2440_AC97+1) @@ -164,6 +187,9 @@ #define IRQ_S3CUART_TX3 IRQ_S3C2443_TX3 #define IRQ_S3CUART_ERR3 IRQ_S3C2443_ERR3 +#define IRQ_LCD_VSYNC IRQ_S3C2443_LCD3 +#define IRQ_LCD_SYSTEM IRQ_S3C2443_LCD2 + #ifdef CONFIG_CPU_S3C2440 #define IRQ_S3C244x_AC97 IRQ_S3C2440_AC97 #else diff --git a/arch/arm/mach-s3c2410/include/mach/map.h b/arch/arm/mach-s3c2410/include/mach/map.h index b049e61460b..091c98a639d 100644 --- a/arch/arm/mach-s3c2410/include/mach/map.h +++ b/arch/arm/mach-s3c2410/include/mach/map.h @@ -63,9 +63,11 @@ #define S3C2440_PA_AC97 (0x5B000000) #define S3C2440_SZ_AC97 SZ_1M -/* S3C2443 High-speed SD/MMC */ +/* S3C2443/S3C2416 High-speed SD/MMC */ #define S3C2443_PA_HSMMC (0x4A800000) -#define S3C2443_SZ_HSMMC (256) +#define S3C2416_PA_HSMMC0 (0x4AC00000) + +#define S3C2443_PA_FB (0x4C800000) /* S3C2412 memory and IO controls */ #define S3C2412_PA_SSMC (0x4F000000) @@ -106,10 +108,12 @@ #define S3C24XX_PA_SDI S3C2410_PA_SDI #define S3C24XX_PA_NAND S3C2410_PA_NAND +#define S3C_PA_FB S3C2443_PA_FB #define S3C_PA_IIC S3C2410_PA_IIC #define S3C_PA_UART S3C24XX_PA_UART #define S3C_PA_USBHOST S3C2410_PA_USBHOST #define S3C_PA_HSMMC0 S3C2443_PA_HSMMC +#define S3C_PA_HSMMC1 S3C2416_PA_HSMMC0 #define S3C_PA_NAND S3C24XX_PA_NAND #endif /* __ASM_ARCH_MAP_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-clock.h b/arch/arm/mach-s3c2410/include/mach/regs-clock.h index 9a0d169be13..3415b60082d 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-clock.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-clock.h @@ -161,4 +161,6 @@ #endif /* CONFIG_CPU_S3C2412 | CONFIG_CPU_S3C2413 */ +#define S3C2416_CLKDIV2 S3C2410_CLKREG(0x28) + #endif /* __ASM_ARM_REGS_CLOCK */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-dsc.h b/arch/arm/mach-s3c2410/include/mach/regs-dsc.h index 3c3853cd3cf..98fd4a05587 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-dsc.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-dsc.h @@ -19,6 +19,42 @@ #define S3C2412_DSC1 S3C2410_GPIOREG(0xe0) #endif +#if defined(CONFIG_CPU_S3C2416) +#define S3C2416_DSC0 S3C2410_GPIOREG(0xc0) +#define S3C2416_DSC1 S3C2410_GPIOREG(0xc4) +#define S3C2416_DSC2 S3C2410_GPIOREG(0xc8) +#define S3C2416_DSC3 S3C2410_GPIOREG(0x110) + +#define S3C2416_SELECT_DSC0 (0 << 30) +#define S3C2416_SELECT_DSC1 (1 << 30) +#define S3C2416_SELECT_DSC2 (2 << 30) +#define S3C2416_SELECT_DSC3 (3 << 30) + +#define S3C2416_DSC_GETSHIFT(x) (x & 30) + +#define S3C2416_DSC0_CF (S3C2416_SELECT_DSC0 | 28) +#define S3C2416_DSC0_CF_5mA (0 << 28) +#define S3C2416_DSC0_CF_10mA (1 << 28) +#define S3C2416_DSC0_CF_15mA (2 << 28) +#define S3C2416_DSC0_CF_21mA (3 << 28) +#define S3C2416_DSC0_CF_MASK (3 << 28) + +#define S3C2416_DSC0_nRBE (S3C2416_SELECT_DSC0 | 26) +#define S3C2416_DSC0_nRBE_5mA (0 << 26) +#define S3C2416_DSC0_nRBE_10mA (1 << 26) +#define S3C2416_DSC0_nRBE_15mA (2 << 26) +#define S3C2416_DSC0_nRBE_21mA (3 << 26) +#define S3C2416_DSC0_nRBE_MASK (3 << 26) + +#define S3C2416_DSC0_nROE (S3C2416_SELECT_DSC0 | 24) +#define S3C2416_DSC0_nROE_5mA (0 << 24) +#define S3C2416_DSC0_nROE_10mA (1 << 24) +#define S3C2416_DSC0_nROE_15mA (2 << 24) +#define S3C2416_DSC0_nROE_21mA (3 << 24) +#define S3C2416_DSC0_nROE_MASK (3 << 24) + +#endif + #if defined(CONFIG_CPU_S3C244X) #define S3C2440_DSC0 S3C2410_GPIOREG(0xc4) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h index fd672f330bf..a0a89d42929 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-gpio.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-gpio.h @@ -17,29 +17,11 @@ #include <mach/gpio-nrs.h> #ifdef CONFIG_CPU_S3C2400 -#define S3C24XX_GPIO_BASE(x) S3C2400_GPIO_BASE(x) -#define S3C24XX_MISCCR S3C2400_MISCCR +#define S3C24XX_MISCCR S3C2400_MISCCR #else -#define S3C24XX_GPIO_BASE(x) S3C2410_GPIO_BASE(x) -#define S3C24XX_MISCCR S3C24XX_GPIOREG2(0x80) +#define S3C24XX_MISCCR S3C24XX_GPIOREG2(0x80) #endif /* CONFIG_CPU_S3C2400 */ - -/* S3C2400 doesn't have a 1:1 mapping to S3C2410 gpio base pins */ - -#define S3C2400_BANKNUM(pin) (((pin) & ~31) / 32) -#define S3C2400_BASEA2B(pin) ((((pin) & ~31) >> 2)) -#define S3C2400_BASEC2H(pin) ((S3C2400_BANKNUM(pin) * 10) + \ - (2 * (S3C2400_BANKNUM(pin)-2))) - -#define S3C2400_GPIO_BASE(pin) (pin < S3C2410_GPIO_BANKC ? \ - S3C2400_BASEA2B(pin)+S3C24XX_VA_GPIO : \ - S3C2400_BASEC2H(pin)+S3C24XX_VA_GPIO) - - -#define S3C2410_GPIO_BASE(pin) ((((pin) & ~31) >> 1) + S3C24XX_VA_GPIO) -#define S3C2410_GPIO_OFFSET(pin) ((pin) & 31) - /* general configuration options */ #define S3C2410_GPIO_LEAVE (0xFFFFFFFF) @@ -610,35 +592,73 @@ #define S3C2410_GPHUP S3C2410_GPIOREG(0x78) #define S3C2410_GPH0_nCTS0 (0x02 << 0) +#define S3C2416_GPH0_TXD0 (0x02 << 0) #define S3C2410_GPH1_nRTS0 (0x02 << 2) +#define S3C2416_GPH1_RXD0 (0x02 << 2) #define S3C2410_GPH2_TXD0 (0x02 << 4) +#define S3C2416_GPH2_TXD1 (0x02 << 4) #define S3C2410_GPH3_RXD0 (0x02 << 6) +#define S3C2416_GPH3_RXD1 (0x02 << 6) #define S3C2410_GPH4_TXD1 (0x02 << 8) +#define S3C2416_GPH4_TXD2 (0x02 << 8) #define S3C2410_GPH5_RXD1 (0x02 << 10) +#define S3C2416_GPH5_RXD2 (0x02 << 10) #define S3C2410_GPH6_TXD2 (0x02 << 12) +#define S3C2416_GPH6_TXD3 (0x02 << 12) #define S3C2410_GPH6_nRTS1 (0x03 << 12) +#define S3C2416_GPH6_nRTS2 (0x03 << 12) #define S3C2410_GPH7_RXD2 (0x02 << 14) +#define S3C2416_GPH7_RXD3 (0x02 << 14) #define S3C2410_GPH7_nCTS1 (0x03 << 14) +#define S3C2416_GPH7_nCTS2 (0x03 << 14) #define S3C2410_GPH8_UCLK (0x02 << 16) +#define S3C2416_GPH8_nCTS0 (0x02 << 16) #define S3C2410_GPH9_CLKOUT0 (0x02 << 18) #define S3C2442_GPH9_nSPICS0 (0x03 << 18) +#define S3C2416_GPH9_nRTS0 (0x02 << 18) #define S3C2410_GPH10_CLKOUT1 (0x02 << 20) +#define S3C2416_GPH10_nCTS1 (0x02 << 20) + +#define S3C2416_GPH11_nRTS1 (0x02 << 22) + +#define S3C2416_GPH12_EXTUARTCLK (0x02 << 24) + +#define S3C2416_GPH13_CLKOUT0 (0x02 << 26) + +#define S3C2416_GPH14_CLKOUT1 (0x02 << 28) /* The S3C2412 and S3C2413 move the GPJ register set to after * GPH, which means all registers after 0x80 are now offset by 0x10 * for the 2412/2413 from the 2410/2440/2442 */ +/* S3C2443 and above */ +#define S3C2440_GPJCON S3C2410_GPIOREG(0xD0) +#define S3C2440_GPJDAT S3C2410_GPIOREG(0xD4) +#define S3C2440_GPJUP S3C2410_GPIOREG(0xD8) + +#define S3C2443_GPKCON S3C2410_GPIOREG(0xE0) +#define S3C2443_GPKDAT S3C2410_GPIOREG(0xE4) +#define S3C2443_GPKUP S3C2410_GPIOREG(0xE8) + +#define S3C2443_GPLCON S3C2410_GPIOREG(0xF0) +#define S3C2443_GPLDAT S3C2410_GPIOREG(0xF4) +#define S3C2443_GPLUP S3C2410_GPIOREG(0xF8) + +#define S3C2443_GPMCON S3C2410_GPIOREG(0x100) +#define S3C2443_GPMDAT S3C2410_GPIOREG(0x104) +#define S3C2443_GPMUP S3C2410_GPIOREG(0x108) + /* miscellaneous control */ #define S3C2400_MISCCR S3C2410_GPIOREG(0x54) #define S3C2410_MISCCR S3C2410_GPIOREG(0x80) @@ -686,6 +706,7 @@ #define S3C2412_MISCCR_CLK1_CLKsrc (0<<8) #define S3C2410_MISCCR_USBSUSPND0 (1<<12) +#define S3C2416_MISCCR_SEL_SUSPND (1<<12) #define S3C2410_MISCCR_USBSUSPND1 (1<<13) #define S3C2410_MISCCR_nRSTCON (1<<16) @@ -695,6 +716,9 @@ #define S3C2410_MISCCR_nEN_SCLKE (1<<19) /* not 2412 */ #define S3C2410_MISCCR_SDSLEEP (7<<17) +#define S3C2416_MISCCR_FLT_I2C (1<<24) +#define S3C2416_MISCCR_HSSPI_EN2 (1<<31) + /* external interrupt control... */ /* S3C2410_EXTINT0 -> irq sense control for EINT0..EINT7 * S3C2410_EXTINT1 -> irq sense control for EINT8..EINT15 @@ -762,8 +786,11 @@ #define S3C2410_GSTATUS1_IDMASK (0xffff0000) #define S3C2410_GSTATUS1_2410 (0x32410000) #define S3C2410_GSTATUS1_2412 (0x32412001) +#define S3C2410_GSTATUS1_2416 (0x32416003) #define S3C2410_GSTATUS1_2440 (0x32440000) #define S3C2410_GSTATUS1_2442 (0x32440aaa) +/* some 2416 CPUs report this value also */ +#define S3C2410_GSTATUS1_2450 (0x32450003) #define S3C2410_GSTATUS2_WTRESET (1<<2) #define S3C2410_GSTATUS2_OFFRESET (1<<1) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-gpioj.h b/arch/arm/mach-s3c2410/include/mach/regs-gpioj.h index 1202ca5e99f..19575e06111 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-gpioj.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-gpioj.h @@ -22,85 +22,49 @@ * pull up works like all other ports. */ -#define S3C2440_GPIO_BANKJ (416) - -#define S3C2440_GPJCON S3C2410_GPIOREG(0xd0) -#define S3C2440_GPJDAT S3C2410_GPIOREG(0xd4) -#define S3C2440_GPJUP S3C2410_GPIOREG(0xd8) - #define S3C2413_GPJCON S3C2410_GPIOREG(0x80) #define S3C2413_GPJDAT S3C2410_GPIOREG(0x84) #define S3C2413_GPJUP S3C2410_GPIOREG(0x88) #define S3C2413_GPJSLPCON S3C2410_GPIOREG(0x8C) -#define S3C2440_GPJ0 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 0) -#define S3C2440_GPJ0_INP (0x00 << 0) #define S3C2440_GPJ0_OUTP (0x01 << 0) #define S3C2440_GPJ0_CAMDATA0 (0x02 << 0) -#define S3C2440_GPJ1 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 1) -#define S3C2440_GPJ1_INP (0x00 << 2) #define S3C2440_GPJ1_OUTP (0x01 << 2) #define S3C2440_GPJ1_CAMDATA1 (0x02 << 2) -#define S3C2440_GPJ2 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 2) -#define S3C2440_GPJ2_INP (0x00 << 4) #define S3C2440_GPJ2_OUTP (0x01 << 4) #define S3C2440_GPJ2_CAMDATA2 (0x02 << 4) -#define S3C2440_GPJ3 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 3) -#define S3C2440_GPJ3_INP (0x00 << 6) #define S3C2440_GPJ3_OUTP (0x01 << 6) #define S3C2440_GPJ3_CAMDATA3 (0x02 << 6) -#define S3C2440_GPJ4 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 4) -#define S3C2440_GPJ4_INP (0x00 << 8) #define S3C2440_GPJ4_OUTP (0x01 << 8) #define S3C2440_GPJ4_CAMDATA4 (0x02 << 8) -#define S3C2440_GPJ5 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 5) -#define S3C2440_GPJ5_INP (0x00 << 10) #define S3C2440_GPJ5_OUTP (0x01 << 10) #define S3C2440_GPJ5_CAMDATA5 (0x02 << 10) -#define S3C2440_GPJ6 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 6) -#define S3C2440_GPJ6_INP (0x00 << 12) #define S3C2440_GPJ6_OUTP (0x01 << 12) #define S3C2440_GPJ6_CAMDATA6 (0x02 << 12) -#define S3C2440_GPJ7 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 7) -#define S3C2440_GPJ7_INP (0x00 << 14) #define S3C2440_GPJ7_OUTP (0x01 << 14) #define S3C2440_GPJ7_CAMDATA7 (0x02 << 14) -#define S3C2440_GPJ8 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 8) -#define S3C2440_GPJ8_INP (0x00 << 16) #define S3C2440_GPJ8_OUTP (0x01 << 16) #define S3C2440_GPJ8_CAMPCLK (0x02 << 16) -#define S3C2440_GPJ9 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 9) -#define S3C2440_GPJ9_INP (0x00 << 18) #define S3C2440_GPJ9_OUTP (0x01 << 18) #define S3C2440_GPJ9_CAMVSYNC (0x02 << 18) -#define S3C2440_GPJ10 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 10) -#define S3C2440_GPJ10_INP (0x00 << 20) #define S3C2440_GPJ10_OUTP (0x01 << 20) #define S3C2440_GPJ10_CAMHREF (0x02 << 20) -#define S3C2440_GPJ11 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 11) -#define S3C2440_GPJ11_INP (0x00 << 22) #define S3C2440_GPJ11_OUTP (0x01 << 22) #define S3C2440_GPJ11_CAMCLKOUT (0x02 << 22) -#define S3C2440_GPJ12 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 12) -#define S3C2440_GPJ12_INP (0x00 << 24) #define S3C2440_GPJ12_OUTP (0x01 << 24) #define S3C2440_GPJ12_CAMRESET (0x02 << 24) -#define S3C2443_GPJ13 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 13) -#define S3C2443_GPJ14 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 14) -#define S3C2443_GPJ15 S3C2410_GPIONO(S3C2440_GPIO_BANKJ, 15) - #endif /* __ASM_ARCH_REGS_GPIOJ_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-irq.h b/arch/arm/mach-s3c2410/include/mach/regs-irq.h index de86ee8812b..0f07ba30b1f 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-irq.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-irq.h @@ -27,6 +27,16 @@ #define S3C2410_SUBSRCPND S3C2410_IRQREG(0x018) #define S3C2410_INTSUBMSK S3C2410_IRQREG(0x01C) +#define S3C2416_PRIORITY_MODE1 S3C2410_IRQREG(0x030) +#define S3C2416_PRIORITY_UPDATE1 S3C2410_IRQREG(0x034) +#define S3C2416_SRCPND2 S3C2410_IRQREG(0x040) +#define S3C2416_INTMOD2 S3C2410_IRQREG(0x044) +#define S3C2416_INTMSK2 S3C2410_IRQREG(0x048) +#define S3C2416_INTPND2 S3C2410_IRQREG(0x050) +#define S3C2416_INTOFFSET2 S3C2410_IRQREG(0x054) +#define S3C2416_PRIORITY_MODE2 S3C2410_IRQREG(0x070) +#define S3C2416_PRIORITY_UPDATE2 S3C2410_IRQREG(0x074) + /* mask: 0=enable, 1=disable * 1 bit EINT, 4=EINT4, 23=EINT23 * EINT0,1,2,3 are not handled here. diff --git a/arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h b/arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h new file mode 100644 index 00000000000..2f31b74974a --- /dev/null +++ b/arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h @@ -0,0 +1,30 @@ +/* arch/arm/mach-s3c2410/include/mach/regs-s3c2416-mem.h + * + * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>, + * as part of OpenInkpot project + * Copyright (c) 2009 Promwad Innovation Company + * Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * S3C2416 memory register definitions +*/ + +#ifndef __ASM_ARM_REGS_S3C2416_MEM +#define __ASM_ARM_REGS_S3C2416_MEM + +#ifndef S3C2416_MEMREG +#define S3C2416_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x)) +#endif + +#define S3C2416_BANKCFG S3C2416_MEMREG(0x00) +#define S3C2416_BANKCON1 S3C2416_MEMREG(0x04) +#define S3C2416_BANKCON2 S3C2416_MEMREG(0x08) +#define S3C2416_BANKCON3 S3C2416_MEMREG(0x0C) + +#define S3C2416_REFRESH S3C2416_MEMREG(0x10) +#define S3C2416_TIMEOUT S3C2416_MEMREG(0x14) + +#endif /* __ASM_ARM_REGS_S3C2416_MEM */ diff --git a/arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h b/arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h new file mode 100644 index 00000000000..e443167efb8 --- /dev/null +++ b/arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h @@ -0,0 +1,24 @@ +/* arch/arm/mach-s3c2410/include/mach/regs-s3c2416.h + * + * Copyright (c) 2009 Yauhen Kharuzhy <jekhor@gmail.com>, + * as part of OpenInkpot project + * Copyright (c) 2009 Promwad Innovation Company + * Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * S3C2416 specific register definitions +*/ + +#ifndef __ASM_ARCH_REGS_S3C2416_H +#define __ASM_ARCH_REGS_S3C2416_H "s3c2416" + +#define S3C2416_SWRST (S3C24XX_VA_CLKPWR + 0x44) +#define S3C2416_SWRST_RESET (0x533C2416) + +/* see regs-power.h for the other registers in the power block. */ + +#endif /* __ASM_ARCH_REGS_S3C2416_H */ + diff --git a/arch/arm/mach-s3c2410/include/mach/regs-s3c2443-clock.h b/arch/arm/mach-s3c2410/include/mach/regs-s3c2443-clock.h index d87ebe0cb62..08ab9dfb6ae 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-s3c2443-clock.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-s3c2443-clock.h @@ -83,8 +83,7 @@ #define S3C2443_HCLKCON_DMA4 (1<<4) #define S3C2443_HCLKCON_DMA5 (1<<5) #define S3C2443_HCLKCON_CAMIF (1<<8) -#define S3C2443_HCLKCON_DISP (1<<9) -#define S3C2443_HCLKCON_LCDC (1<<10) +#define S3C2443_HCLKCON_LCDC (1<<9) #define S3C2443_HCLKCON_USBH (1<<11) #define S3C2443_HCLKCON_USBD (1<<12) #define S3C2443_HCLKCON_HSMMC (1<<16) diff --git a/arch/arm/mach-s3c2410/include/mach/ts.h b/arch/arm/mach-s3c2410/include/mach/ts.h deleted file mode 100644 index dc361700d69..00000000000 --- a/arch/arm/mach-s3c2410/include/mach/ts.h +++ /dev/null @@ -1,21 +0,0 @@ -/* linux/include/asm/arch-s3c2410/ts.h - * - * Copyright (c) 2005 Arnaud Patard <arnaud.patard@rtp-net.org> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#ifndef __ASM_ARM_TS_H -#define __ASM_ARM_TS_H - -struct s3c2410_ts_mach_info { - int delay; - int presc; - int oversampling_shift; -}; - -extern void s3c24xx_ts_set_platdata(struct s3c2410_ts_mach_info *); - -#endif /* __ASM_ARM_TS_H */ diff --git a/arch/arm/mach-s3c2410/include/mach/uncompress.h b/arch/arm/mach-s3c2410/include/mach/uncompress.h index 72f756c5e50..8b283f847da 100644 --- a/arch/arm/mach-s3c2410/include/mach/uncompress.h +++ b/arch/arm/mach-s3c2410/include/mach/uncompress.h @@ -40,7 +40,9 @@ static void arch_detect_cpu(void) cpuid &= S3C2410_GSTATUS1_IDMASK; if (is_arm926() || cpuid == S3C2410_GSTATUS1_2440 || - cpuid == S3C2410_GSTATUS1_2442) { + cpuid == S3C2410_GSTATUS1_2442 || + cpuid == S3C2410_GSTATUS1_2416 || + cpuid == S3C2410_GSTATUS1_2450) { fifo_mask = S3C2440_UFSTAT_TXMASK; fifo_max = 63 << S3C2440_UFSTAT_TXSHIFT; } else { diff --git a/arch/arm/mach-s3c2410/mach-amlm5900.c b/arch/arm/mach-s3c2410/mach-amlm5900.c index 7047317ed7f..34fc05a4244 100644 --- a/arch/arm/mach-s3c2410/mach-amlm5900.c +++ b/arch/arm/mach-s3c2410/mach-amlm5900.c @@ -56,6 +56,7 @@ #include <plat/iic.h> #include <plat/devs.h> #include <plat/cpu.h> +#include <plat/gpio-cfg.h> #ifdef CONFIG_MTD_PARTITIONS @@ -225,8 +226,8 @@ static void amlm5900_init_pm(void) } else { enable_irq_wake(IRQ_EINT9); /* configure the suspend/resume status pin */ - s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_pullup(S3C2410_GPF(2), 0); + s3c_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); + s3c_gpio_setpull(S3C2410_GPF(2), S3C_GPIO_PULL_UP); } } static void __init amlm5900_init(void) diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 02b1b6220cb..c1f90f6fab4 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -61,6 +61,7 @@ #include <plat/devs.h> #include <plat/cpu.h> #include <plat/cpu-freq.h> +#include <plat/gpio-cfg.h> #include <plat/audio-simtec.h> #include "usb-simtec.h" @@ -216,15 +217,13 @@ static struct s3c2410_uartcfg bast_uartcfgs[] __initdata = { static int bast_pm_suspend(struct sys_device *sd, pm_message_t state) { /* ensure that an nRESET is not generated on resume. */ - s3c2410_gpio_setpin(S3C2410_GPA(21), 1); - s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT); - + gpio_direction_output(S3C2410_GPA(21), 1); return 0; } static int bast_pm_resume(struct sys_device *sd) { - s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); + s3c_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT); return 0; } @@ -634,7 +633,7 @@ static void __init bast_map_io(void) s3c24xx_register_clocks(bast_clocks, ARRAY_SIZE(bast_clocks)); - s3c_device_hwmon.dev.platform_data = &bast_hwmon_info; + s3c_hwmon_set_platdata(&bast_hwmon_info); s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc)); s3c24xx_init_clocks(0); @@ -658,6 +657,8 @@ static void __init bast_init(void) nor_simtec_init(); simtec_audio_add(NULL, true, &bast_audio); + WARN_ON(gpio_request(S3C2410_GPA(21), "bast nreset")); + s3c_cpufreq_setboard(&bast_cpufreq); } diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c index fbedd076094..779b45b3f80 100644 --- a/arch/arm/mach-s3c2410/mach-h1940.c +++ b/arch/arm/mach-s3c2410/mach-h1940.c @@ -46,16 +46,17 @@ #include <mach/h1940.h> #include <mach/h1940-latch.h> #include <mach/fb.h> -#include <mach/ts.h> #include <plat/udc.h> #include <plat/iic.h> +#include <plat/gpio-cfg.h> #include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <plat/pll.h> #include <plat/pm.h> #include <plat/mci.h> +#include <plat/ts.h> static struct map_desc h1940_iodesc[] __initdata = { [0] = { @@ -145,6 +146,7 @@ static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = { .delay = 10000, .presc = 49, .oversampling_shift = 2, + .cfg_gpio = s3c24xx_ts_cfg_gpio, }; /** @@ -162,8 +164,8 @@ static struct s3c2410fb_display h1940_lcd __initdata = { .xres = 240, .yres = 320, .bpp = 16, - .left_margin = 20, - .right_margin = 8, + .left_margin = 8, + .right_margin = 20, .hsync_len = 4, .upper_margin = 8, .lower_margin = 7, @@ -207,16 +209,16 @@ static int h1940_backlight_init(struct device *dev) { gpio_request(S3C2410_GPB(0), "Backlight"); - s3c2410_gpio_setpin(S3C2410_GPB(0), 0); - s3c2410_gpio_pullup(S3C2410_GPB(0), 0); - s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0); + gpio_direction_output(S3C2410_GPB(0), 0); + s3c_gpio_setpull(S3C2410_GPB(0), S3C_GPIO_PULL_NONE); + s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPB0_TOUT0); return 0; } static void h1940_backlight_exit(struct device *dev) { - s3c2410_gpio_cfgpin(S3C2410_GPB(0), 1/*S3C2410_GPB0_OUTP*/); + gpio_direction_output(S3C2410_GPB(0), 1); } static struct platform_pwm_backlight_data backlight_data = { @@ -245,18 +247,18 @@ static void h1940_lcd_power_set(struct plat_lcd_data *pd, if (!power) { /* set to 3ec */ - s3c2410_gpio_setpin(S3C2410_GPC(0), 0); + gpio_direction_output(S3C2410_GPC(0), 0); /* wait for 3ac */ do { - value = s3c2410_gpio_getpin(S3C2410_GPC(6)); + value = gpio_get_value(S3C2410_GPC(6)); } while (value); /* set to 38c */ - s3c2410_gpio_setpin(S3C2410_GPC(5), 0); + gpio_direction_output(S3C2410_GPC(5), 0); } else { /* Set to 3ac */ - s3c2410_gpio_setpin(S3C2410_GPC(5), 1); + gpio_direction_output(S3C2410_GPC(5), 1); /* Set to 3ad */ - s3c2410_gpio_setpin(S3C2410_GPC(0), 1); + gpio_direction_output(S3C2410_GPC(0), 1); } } @@ -271,7 +273,6 @@ static struct platform_device h1940_lcd_powerdev = { }; static struct platform_device *h1940_devices[] __initdata = { - &s3c_device_ts, &s3c_device_ohci, &s3c_device_lcd, &s3c_device_wdt, @@ -285,6 +286,8 @@ static struct platform_device *h1940_devices[] __initdata = { &s3c_device_timer[0], &h1940_backlight, &h1940_lcd_powerdev, + &s3c_device_adc, + &s3c_device_ts, }; static void __init h1940_map_io(void) @@ -332,12 +335,13 @@ static void __init h1940_init(void) gpio_request(S3C2410_GPC(5), "LCD power"); gpio_request(S3C2410_GPC(6), "LCD power"); + gpio_direction_input(S3C2410_GPC(6)); platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices)); } MACHINE_START(H1940, "IPAQ-H1940") - /* Maintainer: Ben Dooks <ben@fluff.org> */ + /* Maintainer: Ben Dooks <ben-linux@fluff.org> */ .phys_io = S3C2410_PA_UART, .io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc, .boot_params = S3C2410_SDRAM_PA + 0x100, diff --git a/arch/arm/mach-s3c2410/mach-n30.c b/arch/arm/mach-s3c2410/mach-n30.c index 684710f8814..41f299d983e 100644 --- a/arch/arm/mach-s3c2410/mach-n30.c +++ b/arch/arm/mach-s3c2410/mach-n30.c @@ -26,6 +26,7 @@ #include <linux/serial_core.h> #include <linux/timer.h> #include <linux/io.h> +#include <linux/mmc/host.h> #include <mach/hardware.h> #include <asm/irq.h> @@ -46,6 +47,7 @@ #include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> +#include <plat/mci.h> #include <plat/s3c2410.h> #include <plat/udc.h> @@ -86,10 +88,10 @@ static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd) { switch (cmd) { case S3C2410_UDC_P_ENABLE : - s3c2410_gpio_setpin(S3C2410_GPB(3), 1); + gpio_set_value(S3C2410_GPB(3), 1); break; case S3C2410_UDC_P_DISABLE : - s3c2410_gpio_setpin(S3C2410_GPB(3), 0); + gpio_set_value(S3C2410_GPB(3), 0); break; case S3C2410_UDC_P_RESET : break; @@ -172,8 +174,10 @@ static struct gpio_keys_button n35_buttons[] = { { .gpio = S3C2410_GPF(0), .code = KEY_POWER, + .type = EV_PWR, .desc = "Power", .active_low = 0, + .wakeup = 1, }, { .gpio = S3C2410_GPG(9), @@ -264,6 +268,14 @@ static struct s3c24xx_led_platdata n30_blue_led_pdata = { .def_trigger = "", }; +/* This is the blue LED on the device. Originaly used to indicate GPS activity + * by flashing. */ +static struct s3c24xx_led_platdata n35_blue_led_pdata = { + .name = "blue_led", + .gpio = S3C2410_GPD(8), + .def_trigger = "", +}; + /* This LED is driven by the battery microcontroller, and is blinking * red, blinking green or solid green when the battery is low, * charging or full respectively. By driving GPD9 low, it's possible @@ -275,6 +287,13 @@ static struct s3c24xx_led_platdata n30_warning_led_pdata = { .def_trigger = "", }; +static struct s3c24xx_led_platdata n35_warning_led_pdata = { + .name = "warning_led", + .flags = S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE, + .gpio = S3C2410_GPD(9), + .def_trigger = "", +}; + static struct platform_device n30_blue_led = { .name = "s3c24xx_led", .id = 1, @@ -283,6 +302,14 @@ static struct platform_device n30_blue_led = { }, }; +static struct platform_device n35_blue_led = { + .name = "s3c24xx_led", + .id = 1, + .dev = { + .platform_data = &n35_blue_led_pdata, + }, +}; + static struct platform_device n30_warning_led = { .name = "s3c24xx_led", .id = 2, @@ -291,6 +318,14 @@ static struct platform_device n30_warning_led = { }, }; +static struct platform_device n35_warning_led = { + .name = "s3c24xx_led", + .id = 2, + .dev = { + .platform_data = &n35_warning_led_pdata, + }, +}; + static struct s3c2410fb_display n30_display __initdata = { .type = S3C2410_LCDCON1_TFT, .width = 240, @@ -317,13 +352,36 @@ static struct s3c2410fb_mach_info n30_fb_info __initdata = { .lpcsel = 0x06, }; +static void n30_sdi_set_power(unsigned char power_mode, unsigned short vdd) +{ + switch (power_mode) { + case MMC_POWER_ON: + case MMC_POWER_UP: + gpio_set_value(S3C2410_GPG(4), 1); + break; + case MMC_POWER_OFF: + default: + gpio_set_value(S3C2410_GPG(4), 0); + break; + } +} + +static struct s3c24xx_mci_pdata n30_mci_cfg __initdata = { + .gpio_detect = S3C2410_GPF(1), + .gpio_wprotect = S3C2410_GPG(10), + .ocr_avail = MMC_VDD_32_33, + .set_power = n30_sdi_set_power, +}; + static struct platform_device *n30_devices[] __initdata = { &s3c_device_lcd, &s3c_device_wdt, &s3c_device_i2c0, &s3c_device_iis, &s3c_device_ohci, + &s3c_device_rtc, &s3c_device_usbgadget, + &s3c_device_sdi, &n30_button_device, &n30_blue_led, &n30_warning_led, @@ -334,8 +392,12 @@ static struct platform_device *n35_devices[] __initdata = { &s3c_device_wdt, &s3c_device_i2c0, &s3c_device_iis, + &s3c_device_rtc, &s3c_device_usbgadget, + &s3c_device_sdi, &n35_button_device, + &n35_blue_led, + &n35_warning_led, }; static struct s3c2410_platform_i2c __initdata n30_i2ccfg = { @@ -490,17 +552,15 @@ static void __init n30_map_io(void) s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs)); } -static void __init n30_init_irq(void) -{ - s3c24xx_init_irq(); -} - /* GPB3 is the line that controls the pull-up for the USB D+ line */ static void __init n30_init(void) { + WARN_ON(gpio_request(S3C2410_GPG(4), "mmc power")); + s3c24xx_fb_set_platdata(&n30_fb_info); s3c24xx_udc_set_platdata(&n30_udc_cfg); + s3c24xx_mci_set_platdata(&n30_mci_cfg); s3c_i2c0_set_platdata(&n30_i2ccfg); /* Turn off suspend on both USB ports, and switch the @@ -532,10 +592,13 @@ static void __init n30_init(void) s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST | S3C2410_MISCCR_USBSUSPND0 | S3C2410_MISCCR_USBSUSPND1, - S3C2410_MISCCR_USBSUSPND1); + S3C2410_MISCCR_USBSUSPND0); platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices)); } + + WARN_ON(gpio_request(S3C2410_GPB(3), "udc pup")); + gpio_direction_output(S3C2410_GPB(3), 0); } MACHINE_START(N30, "Acer-N30") @@ -547,7 +610,7 @@ MACHINE_START(N30, "Acer-N30") .boot_params = S3C2410_SDRAM_PA + 0x100, .timer = &s3c24xx_timer, .init_machine = n30_init, - .init_irq = n30_init_irq, + .init_irq = s3c24xx_init_irq, .map_io = n30_map_io, MACHINE_END @@ -559,6 +622,6 @@ MACHINE_START(N35, "Acer-N35") .boot_params = S3C2410_SDRAM_PA + 0x100, .timer = &s3c24xx_timer, .init_machine = n30_init, - .init_irq = n30_init_irq, + .init_irq = s3c24xx_init_irq, .map_io = n30_map_io, MACHINE_END diff --git a/arch/arm/mach-s3c2410/mach-qt2410.c b/arch/arm/mach-s3c2410/mach-qt2410.c index 92a4ec375d8..d0e87b6e2e0 100644 --- a/arch/arm/mach-s3c2410/mach-qt2410.c +++ b/arch/arm/mach-s3c2410/mach-qt2410.c @@ -58,6 +58,7 @@ #include <plat/iic.h> #include <plat/common-smdk.h> +#include <plat/gpio-cfg.h> #include <plat/devs.h> #include <plat/cpu.h> #include <plat/pm.h> @@ -219,10 +220,10 @@ static void spi_gpio_cs(struct s3c2410_spigpio_info *spi, int cs) { switch (cs) { case BITBANG_CS_ACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB(5), 0); + gpio_set_value(S3C2410_GPB(5), 0); break; case BITBANG_CS_INACTIVE: - s3c2410_gpio_setpin(S3C2410_GPB(5), 1); + gpio_set_value(S3C2410_GPB(5), 1); break; } } @@ -347,13 +348,14 @@ static void __init qt2410_machine_init(void) } s3c24xx_fb_set_platdata(&qt2410_fb_info); - s3c2410_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT); + s3c_gpio_cfgpin(S3C2410_GPB(0), S3C2410_GPIO_OUTPUT); s3c2410_gpio_setpin(S3C2410_GPB(0), 1); s3c24xx_udc_set_platdata(&qt2410_udc_cfg); s3c_i2c0_set_platdata(NULL); - s3c2410_gpio_cfgpin(S3C2410_GPB(5), S3C2410_GPIO_OUTPUT); + WARN_ON(gpio_request(S3C2410_GPB(5), "spi cs")); + gpio_direction_output(S3C2410_GPB(5), 1); platform_add_devices(qt2410_devices, ARRAY_SIZE(qt2410_devices)); s3c_pm_init(); diff --git a/arch/arm/mach-s3c2410/mach-vr1000.c b/arch/arm/mach-s3c2410/mach-vr1000.c index 9051f0d3112..d540d79dd26 100644 --- a/arch/arm/mach-s3c2410/mach-vr1000.c +++ b/arch/arm/mach-s3c2410/mach-vr1000.c @@ -357,8 +357,7 @@ static struct clk *vr1000_clocks[] __initdata = { static void vr1000_power_off(void) { - s3c2410_gpio_cfgpin(S3C2410_GPB(9), S3C2410_GPIO_OUTPUT); - s3c2410_gpio_setpin(S3C2410_GPB(9), 1); + gpio_direction_output(S3C2410_GPB(9), 1); } static void __init vr1000_map_io(void) @@ -395,6 +394,8 @@ static void __init vr1000_init(void) nor_simtec_init(); simtec_audio_add(NULL, true, NULL); + + WARN_ON(gpio_request(S3C2410_GPB(9), "power off")); } MACHINE_START(VR1000, "Thorcom-VR1000") diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index 966119c8efe..725636fc4dc 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -60,10 +60,10 @@ static void s3c2410_pm_prepare(void) __raw_writel(calc, phys_to_virt(H1940_SUSPEND_CHECKSUM)); } - /* the RX3715 uses similar code and the same H1940 and the + /* RX3715 and RX1950 use similar to H1940 code and the * same offsets for resume and checksum pointers */ - if (machine_is_rx3715()) { + if (machine_is_rx3715() || machine_is_rx1950()) { void *base = phys_to_virt(H1940_SUSPEND_CHECK); unsigned long ptr; unsigned long calc = 0; @@ -79,6 +79,17 @@ static void s3c2410_pm_prepare(void) if ( machine_is_aml_m5900() ) s3c2410_gpio_setpin(S3C2410_GPF(2), 1); + if (machine_is_rx1950()) { + /* According to S3C2442 user's manual, page 7-17, + * when the system is operating in NAND boot mode, + * the hardware pin configuration - EINT[23:21] – + * must be set as input for starting up after + * wakeup from sleep mode + */ + s3c_gpio_cfgpin(S3C2410_GPG(13), S3C2410_GPIO_INPUT); + s3c_gpio_cfgpin(S3C2410_GPG(14), S3C2410_GPIO_INPUT); + s3c_gpio_cfgpin(S3C2410_GPG(15), S3C2410_GPIO_INPUT); + } } static int s3c2410_pm_resume(struct sys_device *dev) diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c index 91ba42f688a..adc90a3c589 100644 --- a/arch/arm/mach-s3c2410/s3c2410.c +++ b/arch/arm/mach-s3c2410/s3c2410.c @@ -16,6 +16,7 @@ #include <linux/list.h> #include <linux/timer.h> #include <linux/init.h> +#include <linux/gpio.h> #include <linux/clk.h> #include <linux/sysdev.h> #include <linux/serial_core.h> @@ -40,6 +41,10 @@ #include <plat/clock.h> #include <plat/pll.h> +#include <plat/gpio-core.h> +#include <plat/gpio-cfg.h> +#include <plat/gpio-cfg-helpers.h> + /* Initial IO mappings */ static struct map_desc s3c2410_iodesc[] __initdata = { @@ -65,6 +70,9 @@ void __init s3c2410_init_uarts(struct s3c2410_uartcfg *cfg, int no) void __init s3c2410_map_io(void) { + s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up; + s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up; + iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc)); } |