1 files changed, 147 insertions, 61 deletions

diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 776f20560e7..7e1d3758432 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -126,7 +126,7 @@
  * ------+--------------------+--------------------+-------
  * IRQ0  | ICR1A.IRQ0SA=0010  | SDHI2 card detect  | Low
  * IRQ6  | ICR1A.IRQ6SA=0011  | Ether(LAN9220)     | High
- * IRQ7  | ICR1A.IRQ7SA=0010  | LCD Tuch Panel     | Low
+ * IRQ7  | ICR1A.IRQ7SA=0010  | LCD Touch Panel    | Low
  * IRQ8  | ICR2A.IRQ8SA=0010  | MMC/SD card detect | Low
  * IRQ9  | ICR2A.IRQ9SA=0010  | KEY(TCA6408)       | Low
  * IRQ21 | ICR4A.IRQ21SA=0011 | Sensor(ADXL345)    | High
@@ -165,10 +165,10 @@
  * USB1 can become Host by r8a66597, and become Function by renesas_usbhs.
  * But don't select both drivers in same time.
  * These uses same IRQ number for request_irq(), and aren't supporting
- * IRQF_SHARD / IORESOURCE_IRQ_SHAREABLE.
+ * IRQF_SHARED / IORESOURCE_IRQ_SHAREABLE.
  *
  * Actually these are old/new version of USB driver.
- * This mean its register will be broken if it supports SHARD IRQ,
+ * This mean its register will be broken if it supports shared IRQ,
  */
 
 /*
@@ -562,7 +562,121 @@ out:
 		clk_put(hdmi_ick);
 }
 
-/* USB1 (Host) */
+/* USBHS0 is connected to CN22 which takes a USB Mini-B plug
+ *
+ * The sh7372 SoC has IRQ7 set aside for USBHS0 hotplug,
+ * but on this particular board IRQ7 is already used by
+ * the touch screen. This leaves us with software polling.
+ */
+#define USBHS0_POLL_INTERVAL (HZ * 5)
+
+struct usbhs_private {
+	unsigned int usbphyaddr;
+	unsigned int usbcrcaddr;
+	struct renesas_usbhs_platform_info info;
+	struct delayed_work work;
+	struct platform_device *pdev;
+};
+
+#define usbhs_get_priv(pdev)				\
+	container_of(renesas_usbhs_get_info(pdev),	\
+		     struct usbhs_private, info)
+
+#define usbhs_is_connected(priv)			\
+	(!((1 << 7) & __raw_readw(priv->usbcrcaddr)))
+
+static int usbhs_get_vbus(struct platform_device *pdev)
+{
+	return usbhs_is_connected(usbhs_get_priv(pdev));
+}
+
+static void usbhs_phy_reset(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	/* init phy */
+	__raw_writew(0x8a0a, priv->usbcrcaddr);
+}
+
+static int usbhs0_get_id(struct platform_device *pdev)
+{
+	return USBHS_GADGET;
+}
+
+static void usbhs0_work_function(struct work_struct *work)
+{
+	struct usbhs_private *priv = container_of(work, struct usbhs_private,
+						  work.work);
+
+	renesas_usbhs_call_notify_hotplug(priv->pdev);
+	schedule_delayed_work(&priv->work, USBHS0_POLL_INTERVAL);
+}
+
+static int usbhs0_hardware_init(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	priv->pdev = pdev;
+	INIT_DELAYED_WORK(&priv->work, usbhs0_work_function);
+	schedule_delayed_work(&priv->work, USBHS0_POLL_INTERVAL);
+	return 0;
+}
+
+static void usbhs0_hardware_exit(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	cancel_delayed_work_sync(&priv->work);
+}
+
+static struct usbhs_private usbhs0_private = {
+	.usbcrcaddr	= 0xe605810c,		/* USBCR2 */
+	.info = {
+		.platform_callback = {
+			.hardware_init	= usbhs0_hardware_init,
+			.hardware_exit	= usbhs0_hardware_exit,
+			.phy_reset	= usbhs_phy_reset,
+			.get_id		= usbhs0_get_id,
+			.get_vbus	= usbhs_get_vbus,
+		},
+		.driver_param = {
+			.buswait_bwait	= 4,
+		},
+	},
+};
+
+static struct resource usbhs0_resources[] = {
+	[0] = {
+		.name	= "USBHS0",
+		.start	= 0xe6890000,
+		.end	= 0xe68900e6 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x1ca0) /* USB0_USB0I0 */,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device usbhs0_device = {
+	.name	= "renesas_usbhs",
+	.id	= 0,
+	.dev = {
+		.platform_data		= &usbhs0_private.info,
+	},
+	.num_resources	= ARRAY_SIZE(usbhs0_resources),
+	.resource	= usbhs0_resources,
+};
+
+/* USBHS1 is connected to CN31 which takes a USB Mini-AB plug
+ *
+ * Use J30 to select between Host and Function. This setting
+ * can however not be detected by software. Hotplug of USBHS1
+ * is provided via IRQ8.
+ */
+#define IRQ8 evt2irq(0x0300)
+
+/* USBHS1 USB Host support via r8a66597_hcd */
 static void usb1_host_port_power(int port, int power)
 {
 	if (!power) /* only power-on is supported for now */
@@ -579,9 +693,9 @@ static struct r8a66597_platdata usb1_host_data = {
 
 static struct resource usb1_host_resources[] = {
 	[0] = {
-		.name	= "USBHS",
-		.start	= 0xE68B0000,
-		.end	= 0xE68B00E6 - 1,
+		.name	= "USBHS1",
+		.start	= 0xe68b0000,
+		.end	= 0xe68b00e6 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -602,37 +716,14 @@ static struct platform_device usb1_host_device = {
 	.resource	= usb1_host_resources,
 };
 
-/* USB1 (Function) */
+/* USBHS1 USB Function support via renesas_usbhs */
+
 #define USB_PHY_MODE		(1 << 4)
 #define USB_PHY_INT_EN		((1 << 3) | (1 << 2))
 #define USB_PHY_ON		(1 << 1)
 #define USB_PHY_OFF		(1 << 0)
 #define USB_PHY_INT_CLR		(USB_PHY_ON | USB_PHY_OFF)
 
-struct usbhs_private {
-	unsigned int irq;
-	unsigned int usbphyaddr;
-	unsigned int usbcrcaddr;
-	struct renesas_usbhs_platform_info info;
-};
-
-#define usbhs_get_priv(pdev)				\
-	container_of(renesas_usbhs_get_info(pdev),	\
-		     struct usbhs_private, info)
-
-#define usbhs_is_connected(priv)			\
-	(!((1 << 7) & __raw_readw(priv->usbcrcaddr)))
-
-static int usbhs1_get_id(struct platform_device *pdev)
-{
-	return USBHS_GADGET;
-}
-
-static int usbhs1_get_vbus(struct platform_device *pdev)
-{
-	return usbhs_is_connected(usbhs_get_priv(pdev));
-}
-
 static irqreturn_t usbhs1_interrupt(int irq, void *data)
 {
 	struct platform_device *pdev = data;
@@ -654,12 +745,10 @@ static int usbhs1_hardware_init(struct platform_device *pdev)
 	struct usbhs_private *priv = usbhs_get_priv(pdev);
 	int ret;
 
-	irq_set_irq_type(priv->irq, IRQ_TYPE_LEVEL_HIGH);
-
 	/* clear interrupt status */
 	__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->usbphyaddr);
 
-	ret = request_irq(priv->irq, usbhs1_interrupt, 0,
+	ret = request_irq(IRQ8, usbhs1_interrupt, IRQF_TRIGGER_HIGH,
 			  dev_name(&pdev->dev), pdev);
 	if (ret) {
 		dev_err(&pdev->dev, "request_irq err\n");
@@ -679,15 +768,12 @@ static void usbhs1_hardware_exit(struct platform_device *pdev)
 	/* clear interrupt status */
 	__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->usbphyaddr);
 
-	free_irq(priv->irq, pdev);
+	free_irq(IRQ8, pdev);
 }
 
-static void usbhs1_phy_reset(struct platform_device *pdev)
+static int usbhs1_get_id(struct platform_device *pdev)
 {
-	struct usbhs_private *priv = usbhs_get_priv(pdev);
-
-	/* init phy */
-	__raw_writew(0x8a0a, priv->usbcrcaddr);
+	return USBHS_GADGET;
 }
 
 static u32 usbhs1_pipe_cfg[] = {
@@ -710,16 +796,15 @@ static u32 usbhs1_pipe_cfg[] = {
 };
 
 static struct usbhs_private usbhs1_private = {
-	.irq		= evt2irq(0x0300),	/* IRQ8 */
-	.usbphyaddr	= 0xE60581E2,		/* USBPHY1INTAP */
-	.usbcrcaddr	= 0xE6058130,		/* USBCR4 */
+	.usbphyaddr	= 0xe60581e2,		/* USBPHY1INTAP */
+	.usbcrcaddr	= 0xe6058130,		/* USBCR4 */
 	.info = {
 		.platform_callback = {
 			.hardware_init	= usbhs1_hardware_init,
 			.hardware_exit	= usbhs1_hardware_exit,
-			.phy_reset	= usbhs1_phy_reset,
 			.get_id		= usbhs1_get_id,
-			.get_vbus	= usbhs1_get_vbus,
+			.phy_reset	= usbhs_phy_reset,
+			.get_vbus	= usbhs_get_vbus,
 		},
 		.driver_param = {
 			.buswait_bwait	= 4,
@@ -731,9 +816,9 @@ static struct usbhs_private usbhs1_private = {
 
 static struct resource usbhs1_resources[] = {
 	[0] = {
-		.name	= "USBHS",
-		.start	= 0xE68B0000,
-		.end	= 0xE68B00E6 - 1,
+		.name	= "USBHS1",
+		.start	= 0xe68b0000,
+		.end	= 0xe68b00e6 - 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
@@ -752,7 +837,6 @@ static struct platform_device usbhs1_device = {
 	.resource	= usbhs1_resources,
 };
 
-
 /* LED */
 static struct gpio_led mackerel_leds[] = {
 	{
@@ -1203,6 +1287,7 @@ static struct platform_device *mackerel_devices[] __initdata = {
 	&nor_flash_device,
 	&smc911x_device,
 	&lcdc_device,
+	&usbhs0_device,
 	&usb1_host_device,
 	&usbhs1_device,
 	&leds_device,
@@ -1301,6 +1386,7 @@ static void __init mackerel_map_io(void)
 
 #define GPIO_PORT9CR	0xE6051009
 #define GPIO_PORT10CR	0xE605100A
+#define GPIO_PORT167CR	0xE60520A7
 #define GPIO_PORT168CR	0xE60520A8
 #define SRCR4		0xe61580bc
 #define USCCR1		0xE6058144
@@ -1354,17 +1440,17 @@ static void __init mackerel_init(void)
 	gpio_request(GPIO_PORT151, NULL); /* LCDDON */
 	gpio_direction_output(GPIO_PORT151, 1);
 
-	/* USB enable */
-	gpio_request(GPIO_FN_VBUS0_1,    NULL);
-	gpio_request(GPIO_FN_IDIN_1_18,  NULL);
-	gpio_request(GPIO_FN_PWEN_1_115, NULL);
-	gpio_request(GPIO_FN_OVCN_1_114, NULL);
-	gpio_request(GPIO_FN_EXTLP_1,    NULL);
-	gpio_request(GPIO_FN_OVCN2_1,    NULL);
-	gpio_pull_down(GPIO_PORT168CR);
-
-	/* setup USB phy */
-	__raw_writew(0x8a0a, 0xE6058130);	/* USBCR4 */
+	/* USBHS0 */
+	gpio_request(GPIO_FN_VBUS0_0, NULL);
+	gpio_pull_down(GPIO_PORT168CR); /* VBUS0_0 pull down */
+
+	/* USBHS1 */
+	gpio_request(GPIO_FN_VBUS0_1, NULL);
+	gpio_pull_down(GPIO_PORT167CR); /* VBUS0_1 pull down */
+	gpio_request(GPIO_FN_IDIN_1_113, NULL);
+
+	/* USB phy tweak to make the r8a66597_hcd host driver work */
+	__raw_writew(0x8a0a, 0xe6058130);       /* USBCR4 */
 
 	/* enable FSI2 port A (ak4643) */
 	gpio_request(GPIO_FN_FSIAIBT,	NULL);