diff options
Diffstat (limited to 'arch/arm/mach-u300')
-rw-r--r-- | arch/arm/mach-u300/core.c | 2 | ||||
-rw-r--r-- | arch/arm/mach-u300/spi.c | 4 | ||||
-rw-r--r-- | arch/arm/mach-u300/timer.c | 33 |
3 files changed, 15 insertions, 24 deletions
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 513d6abec1f..399c89f14df 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -1791,7 +1791,7 @@ static void __init u300_assign_physmem(void) 0 == res->start) { res->start = curr_start; res->end += curr_start; - curr_start += (res->end - res->start + 1); + curr_start += resource_size(res); printk(KERN_INFO "core.c: Mapping RAM " \ "%#x-%#x to device %s:%s\n", diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c index 5767208f1c1..7b597e2b19e 100644 --- a/arch/arm/mach-u300/spi.c +++ b/arch/arm/mach-u300/spi.c @@ -40,8 +40,8 @@ struct pl022_config_chip dummy_chip_info = { .hierarchy = SSP_MASTER, /* 0 = drive TX even as slave, 1 = do not drive TX as slave */ .slave_tx_disable = 0, - .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, - .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, + .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM, + .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC, .ctrl_len = SSP_BITS_12, .wait_state = SSP_MWIRE_WAIT_ZERO, .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, diff --git a/arch/arm/mach-u300/timer.c b/arch/arm/mach-u300/timer.c index 18d7fa0603c..5f51bdeef0e 100644 --- a/arch/arm/mach-u300/timer.c +++ b/arch/arm/mach-u300/timer.c @@ -27,9 +27,6 @@ #include <asm/mach/time.h> #include <asm/mach/irq.h> -/* Be able to sleep for atleast 4 seconds (usually more) */ -#define APPTIMER_MIN_RANGE 4 - /* * APP side special timer registers * This timer contains four timers which can fire an interrupt each. @@ -309,11 +306,11 @@ static int u300_set_next_event(unsigned long cycles, /* Use general purpose timer 1 as clock event */ static struct clock_event_device clockevent_u300_1mhz = { - .name = "GPT1", - .rating = 300, /* Reasonably fast and accurate clock event */ - .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, - .set_next_event = u300_set_next_event, - .set_mode = u300_set_mode, + .name = "GPT1", + .rating = 300, /* Reasonably fast and accurate clock event */ + .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, + .set_next_event = u300_set_next_event, + .set_mode = u300_set_mode, }; /* Clock event timer interrupt handler */ @@ -328,9 +325,9 @@ static irqreturn_t u300_timer_interrupt(int irq, void *dev_id) } static struct irqaction u300_timer_irq = { - .name = "U300 Timer Tick", - .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, - .handler = u300_timer_interrupt, + .name = "U300 Timer Tick", + .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL, + .handler = u300_timer_interrupt, }; /* @@ -413,16 +410,10 @@ static void __init u300_timer_init(void) "GPT2", rate, 300, 32, clocksource_mmio_readl_up)) pr_err("timer: failed to initialize U300 clock source\n"); - clockevents_calc_mult_shift(&clockevent_u300_1mhz, - rate, APPTIMER_MIN_RANGE); - /* 32bit counter, so 32bits delta is max */ - clockevent_u300_1mhz.max_delta_ns = - clockevent_delta2ns(0xffffffff, &clockevent_u300_1mhz); - /* This timer is slow enough to set for 1 cycle == 1 MHz */ - clockevent_u300_1mhz.min_delta_ns = - clockevent_delta2ns(1, &clockevent_u300_1mhz); - clockevent_u300_1mhz.cpumask = cpumask_of(0); - clockevents_register_device(&clockevent_u300_1mhz); + /* Configure and register the clockevent */ + clockevents_config_and_register(&clockevent_u300_1mhz, rate, + 1, 0xffffffff); + /* * TODO: init and register the rest of the timers too, they can be * used by hrtimers! |