diff options
Diffstat (limited to 'arch/arm/mach-u300')
| -rw-r--r-- | arch/arm/mach-u300/core.c | 4 | ||||
| -rw-r--r-- | arch/arm/mach-u300/dummyspichip.c | 1 | ||||
| -rw-r--r-- | arch/arm/mach-u300/include/mach/debug-macro.S | 2 | ||||
| -rw-r--r-- | arch/arm/mach-u300/mmc.c | 4 |
4 files changed, 7 insertions, 4 deletions
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 01b50313914..5f34eb674d6 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -358,7 +358,7 @@ static struct resource ave_resources[] = { /* * The AVE3e requires two regions of 256MB that it considers * "invisible". The hardware will not be able to access these - * adresses, so they should never point to system RAM. + * addresses, so they should never point to system RAM. */ { .name = "AVE3e Reserved 0", @@ -1596,7 +1596,7 @@ static void __init u300_init_check_chip(void) /* * Some devices and their resources require reserved physical memory from * the end of the available RAM. This function traverses the list of devices - * and assigns actual adresses to these. + * and assigns actual addresses to these. */ static void __init u300_assign_physmem(void) { diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c index 962f9de454d..5f55012b7c9 100644 --- a/arch/arm/mach-u300/dummyspichip.c +++ b/arch/arm/mach-u300/dummyspichip.c @@ -15,6 +15,7 @@ #include <linux/mutex.h> #include <linux/spi/spi.h> #include <linux/dma-mapping.h> +#include <linux/slab.h> /* * WARNING! Do not include this pl022-specific controller header * for any generic driver. It is only done in this dummy chip diff --git a/arch/arm/mach-u300/include/mach/debug-macro.S b/arch/arm/mach-u300/include/mach/debug-macro.S index ca4a028c266..92c12420256 100644 --- a/arch/arm/mach-u300/include/mach/debug-macro.S +++ b/arch/arm/mach-u300/include/mach/debug-macro.S @@ -11,7 +11,7 @@ #include <mach/hardware.h> .macro addruart, rx, tmp - /* If we move the adress using MMU, use this. */ + /* If we move the address using MMU, use this. */ mrc p15, 0, \rx, c1, c0 tst \rx, #1 @ MMU enabled? ldreq \rx, = U300_SLOW_PER_PHYS_BASE @ MMU off, physical address diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c index 109f5a6e71c..88506d03059 100644 --- a/arch/arm/mach-u300/mmc.c +++ b/arch/arm/mach-u300/mmc.c @@ -20,6 +20,7 @@ #include <linux/regulator/machine.h> #include <linux/gpio.h> #include <linux/amba/mmci.h> +#include <linux/slab.h> #include "mmc.h" #include "padmux.h" @@ -101,11 +102,12 @@ int __devinit mmc_init(struct amba_device *adev) * we have a regulator we can control instead. */ /* Nominally 2.85V on our platform */ + mmci_card->mmc0_plat_data.f_max = 24000000; mmci_card->mmc0_plat_data.status = mmc_status; mmci_card->mmc0_plat_data.gpio_wp = -1; mmci_card->mmc0_plat_data.gpio_cd = -1; mmci_card->mmc0_plat_data.capabilities = MMC_CAP_MMC_HIGHSPEED | - MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA; + MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA; mmcsd_device->platform_data = (void *) &mmci_card->mmc0_plat_data; |