diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-mop500-sdi.c')
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500-sdi.c | 61 |
1 files changed, 44 insertions, 17 deletions
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c index 7c6cb4fa47a..d0cb9e5eb87 100644 --- a/arch/arm/mach-ux500/board-mop500-sdi.c +++ b/arch/arm/mach-ux500/board-mop500-sdi.c @@ -32,13 +32,32 @@ #define MCI_DATA31DIREN (1 << 5) #define MCI_FBCLKEN (1 << 7) +/* GPIO pins used by the sdi0 level shifter */ +static int sdi0_en = -1; +static int sdi0_vsel = -1; + static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd, unsigned char power_mode) { - if (power_mode == MMC_POWER_UP) - gpio_set_value_cansleep(GPIO_SDMMC_EN, 1); - else if (power_mode == MMC_POWER_OFF) - gpio_set_value_cansleep(GPIO_SDMMC_EN, 0); + switch (power_mode) { + case MMC_POWER_UP: + case MMC_POWER_ON: + /* + * Level shifter voltage should depend on vdd to when deciding + * on either 1.8V or 2.9V. Once the decision has been made the + * level shifter must be disabled and re-enabled with a changed + * select signal in order to switch the voltage. Since there is + * no framework support yet for indicating 1.8V in vdd, use the + * default 2.9V. + */ + gpio_direction_output(sdi0_vsel, 0); + gpio_direction_output(sdi0_en, 1); + break; + case MMC_POWER_OFF: + gpio_direction_output(sdi0_vsel, 0); + gpio_direction_output(sdi0_en, 0); + break; + } return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN | MCI_DATA2DIREN | MCI_DATA31DIREN; @@ -67,8 +86,10 @@ static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = { static struct mmci_platform_data mop500_sdi0_data = { .vdd_handler = mop500_sdi0_vdd_handler, .ocr_mask = MMC_VDD_29_30, - .f_max = 100000000, - .capabilities = MMC_CAP_4_BIT_DATA, + .f_max = 50000000, + .capabilities = MMC_CAP_4_BIT_DATA | + MMC_CAP_SD_HIGHSPEED | + MMC_CAP_MMC_HIGHSPEED, .gpio_wp = -1, #ifdef CONFIG_STE_DMA40 .dma_filter = stedma40_filter, @@ -77,10 +98,6 @@ static struct mmci_platform_data mop500_sdi0_data = { #endif }; -/* GPIO pins used by the sdi0 level shifter */ -static int sdi0_en = -1; -static int sdi0_vsel = -1; - static void sdi0_configure(void) { int ret; @@ -140,7 +157,7 @@ static struct stedma40_chan_cfg mop500_sdi2_dma_cfg_tx = { static struct mmci_platform_data mop500_sdi2_data = { .ocr_mask = MMC_VDD_165_195, - .f_max = 100000000, + .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, .gpio_cd = -1, .gpio_wp = -1, @@ -177,7 +194,7 @@ static struct stedma40_chan_cfg mop500_sdi4_dma_cfg_tx = { static struct mmci_platform_data mop500_sdi4_data = { .ocr_mask = MMC_VDD_29_30, - .f_max = 100000000, + .f_max = 50000000, .capabilities = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA | MMC_CAP_MMC_HIGHSPEED, .gpio_cd = -1, @@ -199,17 +216,27 @@ void __init mop500_sdi_init(void) /* PoP:ed eMMC on top of DB8500 v1.0 has problems with high speed */ if (!cpu_is_u8500v10()) mop500_sdi2_data.capabilities |= MMC_CAP_MMC_HIGHSPEED; - db8500_add_sdi2(&mop500_sdi2_data, periphid); + /* sdi2 on snowball is in ATL_B mode for FSMC (LAN) */ + if (!machine_is_snowball()) + db8500_add_sdi2(&mop500_sdi2_data, periphid); /* On-board eMMC */ db8500_add_sdi4(&mop500_sdi4_data, periphid); - if (machine_is_hrefv60()) { - mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO; - sdi0_en = HREFV60_SDMMC_EN_GPIO; - sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO; + if (machine_is_hrefv60() || machine_is_snowball()) { + if (machine_is_hrefv60()) { + mop500_sdi0_data.gpio_cd = HREFV60_SDMMC_CD_GPIO; + sdi0_en = HREFV60_SDMMC_EN_GPIO; + sdi0_vsel = HREFV60_SDMMC_1V8_3V_GPIO; + } else if (machine_is_snowball()) { + mop500_sdi0_data.gpio_cd = SNOWBALL_SDMMC_CD_GPIO; + mop500_sdi0_data.cd_invert = true; + sdi0_en = SNOWBALL_SDMMC_EN_GPIO; + sdi0_vsel = SNOWBALL_SDMMC_1V8_3V_GPIO; + } sdi0_configure(); } + /* * On boards with the TC35892 GPIO expander, sdi0 will finally * be added when the TC35892 initializes and calls |