1 files changed, 0 insertions, 78 deletions
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
deleted file mode 100644
index 514d40b625a..00000000000
--- a/arch/arm/mach-ux500/board-mop500.c
+++ /dev/null
@@ -1,78 +0,0 @@
-/*
- * Copyright (C) 2008-2012 ST-Ericsson
- *
- * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2, as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/platform_data/db8500_thermal.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl022.h>
-#include <linux/mfd/abx500/ab8500.h>
-#include <linux/regulator/ab8500.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/driver.h>
-#include <linux/mfd/tps6105x.h>
-#include <linux/platform_data/leds-lp55xx.h>
-#include <linux/input.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/pinctrl/consumer.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
-#include <linux/platform_data/dma-ste-dma40.h>
-
-#include <asm/mach-types.h>
-
-#include "setup.h"
-#include "devices.h"
-#include "irqs.h"
-
-#include "ste-dma40-db8500.h"
-#include "db8500-regs.h"
-#include "devices-db8500.h"
-#include "board-mop500.h"
-#include "board-mop500-regulators.h"
-
-struct ab8500_platform_data ab8500_platdata = {
-	.irq_base	= MOP500_AB8500_IRQ_BASE,
-	.regulator	= &ab8500_regulator_plat_data,
-};
-
-#ifdef CONFIG_STE_DMA40
-static struct stedma40_chan_cfg ssp0_dma_cfg_rx = {
-	.mode = STEDMA40_MODE_LOGICAL,
-	.dir = DMA_DEV_TO_MEM,
-	.dev_type = DB8500_DMA_DEV8_SSP0,
-};
-
-static struct stedma40_chan_cfg ssp0_dma_cfg_tx = {
-	.mode = STEDMA40_MODE_LOGICAL,
-	.dir = DMA_MEM_TO_DEV,
-	.dev_type = DB8500_DMA_DEV8_SSP0,
-};
-#endif
-
-struct pl022_ssp_controller ssp0_plat = {
-	.bus_id = 0,
-#ifdef CONFIG_STE_DMA40
-	.enable_dma = 1,
-	.dma_filter = stedma40_filter,
-	.dma_rx_param = &ssp0_dma_cfg_rx,
-	.dma_tx_param = &ssp0_dma_cfg_tx,
-#else
-	.enable_dma = 0,
-#endif
-	/* on this platform, gpio 31,142,144,214 &
-	 * 224 are connected as chip selects
-	 */
-	.num_chipselect = 5,
-};