diff options
Diffstat (limited to 'arch/arm/mach-ux500/board-mop500.h')
| -rw-r--r-- | arch/arm/mach-ux500/board-mop500.h | 63 |
1 files changed, 50 insertions, 13 deletions
diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index de18a2a23e6..f926d3db620 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -7,40 +7,77 @@ #ifndef __BOARD_MOP500_H #define __BOARD_MOP500_H -/* snowball GPIO for MMC card */ -#define SNOWBALL_SDMMC_EN_GPIO 217 -#define SNOWBALL_SDMMC_1V8_3V_GPIO 228 -#define SNOWBALL_SDMMC_CD_GPIO 218 +/* Snowball specific GPIO assignments, this board has no GPIO expander */ +#define SNOWBALL_ACCEL_INT1_GPIO 163 +#define SNOWBALL_ACCEL_INT2_GPIO 164 +#define SNOWBALL_MAGNET_DRDY_GPIO 165 +#define SNOWBALL_SDMMC_EN_GPIO 217 +#define SNOWBALL_SDMMC_1V8_3V_GPIO 228 +#define SNOWBALL_SDMMC_CD_GPIO 218 /* HREFv60-specific GPIO assignments, this board has no GPIO expander */ -#define HREFV60_TOUCH_RST_GPIO 143 -#define HREFV60_PROX_SENSE_GPIO 217 -#define HREFV60_HAL_SW_GPIO 145 -#define HREFV60_SDMMC_EN_GPIO 169 #define HREFV60_SDMMC_1V8_3V_GPIO 5 -#define HREFV60_SDMMC_CD_GPIO 95 -#define HREFV60_ACCEL_INT1_GPIO 82 -#define HREFV60_ACCEL_INT2_GPIO 83 +#define HREFV60_CAMERA_FLASH_ENABLE 21 #define HREFV60_MAGNET_DRDY_GPIO 32 #define HREFV60_DISP1_RST_GPIO 65 #define HREFV60_DISP2_RST_GPIO 66 +#define HREFV60_ACCEL_INT1_GPIO 82 +#define HREFV60_ACCEL_INT2_GPIO 83 +#define HREFV60_SDMMC_CD_GPIO 95 +#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140 +#define HREFV60_TOUCH_RST_GPIO 143 +#define HREFV60_HAL_SW_GPIO 145 +#define HREFV60_SDMMC_EN_GPIO 169 +#define HREFV60_MMIO_XENON_CHARGE 170 +#define HREFV60_PROX_SENSE_GPIO 217 + +/* MOP500 generic GPIOs */ +#define CAMERA_FLASH_INT_PIN 7 +#define CYPRESS_TOUCH_INT_PIN 84 +#define XSHUTDOWN_PRIMARY_SENSOR 141 +#define XSHUTDOWN_SECONDARY_SENSOR 142 +#define CYPRESS_TOUCH_RST_GPIO 143 +#define MOP500_HDMI_RST_GPIO 196 +#define CYPRESS_SLAVE_SELECT_GPIO 216 /* GPIOs on the TC35892 expander */ #define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x)) +#define GPIO_MAGNET_DRDY MOP500_EGPIO(1) #define GPIO_SDMMC_CD MOP500_EGPIO(3) +#define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4) +#define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5) #define GPIO_PROX_SENSOR MOP500_EGPIO(7) +#define GPIO_HAL_SENSOR MOP500_EGPIO(8) +#define GPIO_ACCEL_INT1 MOP500_EGPIO(10) +#define GPIO_ACCEL_INT2 MOP500_EGPIO(11) #define GPIO_BU21013_CS MOP500_EGPIO(13) +#define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14) +#define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15) #define GPIO_SDMMC_EN MOP500_EGPIO(17) #define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18) #define MOP500_EGPIO_END MOP500_EGPIO(24) -/* GPIOs on the AB8500 mixed-signals circuit */ -#define MOP500_AB8500_GPIO(x) (MOP500_EGPIO_END + (x)) +/* + * GPIOs on the AB8500 mixed-signals circuit + * Notice that we subtract 1 from the number passed into the macro, this is + * because the AB8500 GPIO pins are enumbered starting from 1, so the value in + * parens matches the GPIO pin number in the data sheet. + */ +#define MOP500_AB8500_GPIO(x) (MOP500_EGPIO_END + (x) - 1) +/*Snowball AB8500 GPIO */ +#define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */ +#define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */ +#define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */ +#define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */ +#define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */ +#define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */ +#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ struct i2c_board_info; extern void mop500_sdi_init(void); extern void snowball_sdi_init(void); +extern void hrefv60_sdi_init(void); extern void mop500_sdi_tc35892_init(void); void __init mop500_u8500uib_init(void); void __init mop500_stuib_init(void); |