diff options
Diffstat (limited to 'arch/arm/plat-omap/Kconfig')
| -rw-r--r-- | arch/arm/plat-omap/Kconfig | 112 |
1 files changed, 112 insertions, 0 deletions
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig new file mode 100644 index 00000000000..345365852f8 --- /dev/null +++ b/arch/arm/plat-omap/Kconfig @@ -0,0 +1,112 @@ +if ARCH_OMAP + +menu "TI OMAP Implementations" + +config ARCH_OMAP_OTG + bool + +choice + prompt "OMAP System Type" + default ARCH_OMAP1 + +config ARCH_OMAP1 + bool "TI OMAP1" + +config ARCH_OMAP2 + bool "TI OMAP2" + +endchoice + +comment "OMAP Feature Selections" + +config OMAP_RESET_CLOCKS + bool "Reset unused clocks during boot" + depends on ARCH_OMAP + default n + help + Say Y if you want to reset unused clocks during boot. + This option saves power, but assumes all drivers are + using the clock framework. Broken drivers that do not + yet use clock framework may not work with this option. + If you are booting from another operating system, you + probably do not want this option enabled until your + device drivers work properly. + +config OMAP_MUX + bool "OMAP multiplexing support" + depends on ARCH_OMAP + default y + help + Pin multiplexing support for OMAP boards. If your bootloader + sets the multiplexing correctly, say N. Otherwise, or if unsure, + say Y. + +config OMAP_MUX_DEBUG + bool "Multiplexing debug output" + depends on OMAP_MUX + default n + help + Makes the multiplexing functions print out a lot of debug info. + This is useful if you want to find out the correct values of the + multiplexing registers. + +config OMAP_MUX_WARNINGS + bool "Warn about pins the bootloader didn't set up" + depends on OMAP_MUX + default y + help + Choose Y here to warn whenever driver initialization logic needs + to change the pin multiplexing setup. When there are no warnings + printed, it's safe to deselect OMAP_MUX for your product. + +choice + prompt "System timer" + default OMAP_MPU_TIMER + +config OMAP_MPU_TIMER + bool "Use mpu timer" + help + Select this option if you want to use the OMAP mpu timer. This + timer provides more intra-tick resolution than the 32KHz timer, + but consumes more power. + +config OMAP_32K_TIMER + bool "Use 32KHz timer" + depends on ARCH_OMAP16XX + help + Select this option if you want to enable the OMAP 32KHz timer. + This timer saves power compared to the OMAP_MPU_TIMER, and has + support for no tick during idle. The 32KHz timer provides less + intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is + currently only available for OMAP-16xx. + +endchoice + +config OMAP_32K_TIMER_HZ + int "Kernel internal timer frequency for 32KHz timer" + range 32 1024 + depends on OMAP_32K_TIMER + default "128" + help + Kernel internal timer frequency should be a divisor of 32768, + such as 64 or 128. + +choice + prompt "Low-level debug console UART" + depends on ARCH_OMAP + default OMAP_LL_DEBUG_UART1 + +config OMAP_LL_DEBUG_UART1 + bool "UART1" + +config OMAP_LL_DEBUG_UART2 + bool "UART2" + +config OMAP_LL_DEBUG_UART3 + bool "UART3" + +endchoice + +endmenu + +endif |