diff options
Diffstat (limited to 'arch/arm/plat-omap/include/plat/omap-serial.h')
| -rw-r--r-- | arch/arm/plat-omap/include/plat/omap-serial.h | 128 |
1 files changed, 128 insertions, 0 deletions
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h new file mode 100644 index 00000000000..c8dae02f070 --- /dev/null +++ b/arch/arm/plat-omap/include/plat/omap-serial.h @@ -0,0 +1,128 @@ +/* + * Driver for OMAP-UART controller. + * Based on drivers/serial/8250.c + * + * Copyright (C) 2010 Texas Instruments. + * + * Authors: + * Govindraj R <govindraj.raja@ti.com> + * Thara Gopinath <thara@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __OMAP_SERIAL_H__ +#define __OMAP_SERIAL_H__ + +#include <linux/serial_core.h> +#include <linux/platform_device.h> + +#include <plat/mux.h> + +#define DRIVER_NAME "omap-hsuart" + +/* + * Use tty device name as ttyO, [O -> OMAP] + * in bootargs we specify as console=ttyO0 if uart1 + * is used as console uart. + */ +#define OMAP_SERIAL_NAME "ttyO" + +#define OMAP_MDR1_DISABLE 0x07 +#define OMAP_MDR1_MODE13X 0x03 +#define OMAP_MDR1_MODE16X 0x00 +#define OMAP_MODE13X_SPEED 230400 + +/* + * LCR = 0XBF: Switch to Configuration Mode B. + * In configuration mode b allow access + * to EFR,DLL,DLH. + * Reference OMAP TRM Chapter 17 + * Section: 1.4.3 Mode Selection + */ +#define OMAP_UART_LCR_CONF_MDB 0XBF + +/* WER = 0x7F + * Enable module level wakeup in WER reg + */ +#define OMAP_UART_WER_MOD_WKUP 0X7F + +/* Enable XON/XOFF flow control on output */ +#define OMAP_UART_SW_TX 0x04 + +/* Enable XON/XOFF flow control on input */ +#define OMAP_UART_SW_RX 0x04 + +#define OMAP_UART_SYSC_RESET 0X07 +#define OMAP_UART_TCR_TRIG 0X0F +#define OMAP_UART_SW_CLR 0XF0 +#define OMAP_UART_FIFO_CLR 0X06 + +#define OMAP_UART_DMA_CH_FREE -1 + +#define RX_TIMEOUT (3 * HZ) +#define OMAP_MAX_HSUART_PORTS 4 + +#define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA + +struct omap_uart_port_info { + bool dma_enabled; /* To specify DMA Mode */ + unsigned int uartclk; /* UART clock rate */ + void __iomem *membase; /* ioremap cookie or NULL */ + resource_size_t mapbase; /* resource base */ + unsigned long irqflags; /* request_irq flags */ + upf_t flags; /* UPF_* flags */ +}; + +struct uart_omap_dma { + u8 uart_dma_tx; + u8 uart_dma_rx; + int rx_dma_channel; + int tx_dma_channel; + dma_addr_t rx_buf_dma_phys; + dma_addr_t tx_buf_dma_phys; + unsigned int uart_base; + /* + * Buffer for rx dma.It is not required for tx because the buffer + * comes from port structure. + */ + unsigned char *rx_buf; + unsigned int prev_rx_dma_pos; + int tx_buf_size; + int tx_dma_used; + int rx_dma_used; + spinlock_t tx_lock; + spinlock_t rx_lock; + /* timer to poll activity on rx dma */ + struct timer_list rx_timer; + int rx_buf_size; + int rx_timeout; +}; + +struct uart_omap_port { + struct uart_port port; + struct uart_omap_dma uart_dma; + struct platform_device *pdev; + + unsigned char ier; + unsigned char lcr; + unsigned char mcr; + unsigned char fcr; + unsigned char efr; + + int use_dma; + /* + * Some bits in registers are cleared on a read, so they must + * be saved whenever the register is read but the bits will not + * be immediately processed. + */ + unsigned int lsr_break_flag; + unsigned char msr_saved_flags; + char name[20]; + unsigned long port_activity; +}; + +#endif /* __OMAP_SERIAL_H__ */ |