diff options
Diffstat (limited to 'arch/arm/plat-s3c/Kconfig')
| -rw-r--r-- | arch/arm/plat-s3c/Kconfig | 215 |
1 files changed, 0 insertions, 215 deletions
diff --git a/arch/arm/plat-s3c/Kconfig b/arch/arm/plat-s3c/Kconfig deleted file mode 100644 index 9e9d0286e48..00000000000 --- a/arch/arm/plat-s3c/Kconfig +++ /dev/null @@ -1,215 +0,0 @@ -# Copyright 2007 Simtec Electronics -# -# Licensed under GPLv2 - -config PLAT_S3C - bool - depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX - default y - select NO_IOPORT - help - Base platform code for any Samsung S3C device - -# low-level serial option nodes - -if PLAT_S3C - -config CPU_LLSERIAL_S3C2410_ONLY - bool - default y if CPU_LLSERIAL_S3C2410 && !CPU_LLSERIAL_S3C2440 - -config CPU_LLSERIAL_S3C2440_ONLY - bool - default y if CPU_LLSERIAL_S3C2440 && !CPU_LLSERIAL_S3C2410 - -config CPU_LLSERIAL_S3C2410 - bool - help - Selected if there is an S3C2410 (or register compatible) serial - low-level implementation needed - -config CPU_LLSERIAL_S3C2440 - bool - help - Selected if there is an S3C2440 (or register compatible) serial - low-level implementation needed - -# boot configurations - -comment "Boot options" - -config S3C_BOOT_WATCHDOG - bool "S3C Initialisation watchdog" - depends on S3C2410_WATCHDOG - help - Say y to enable the watchdog during the kernel decompression - stage. If the kernel fails to uncompress, then the watchdog - will trigger a reset and the system should restart. - -config S3C_BOOT_ERROR_RESET - bool "S3C Reboot on decompression error" - help - Say y here to use the watchdog to reset the system if the - kernel decompressor detects an error during decompression. - -config S3C_BOOT_UART_FORCE_FIFO - bool "Force UART FIFO on during boot process" - default y - help - Say Y here to force the UART FIFOs on during the kernel - uncompressor - -comment "Power management" - -config S3C2410_PM_DEBUG - bool "S3C2410 PM Suspend debug" - depends on PM - help - Say Y here if you want verbose debugging from the PM Suspend and - Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> - for more information. - -config S3C_PM_DEBUG_LED_SMDK - bool "SMDK LED suspend/resume debugging" - depends on PM && (MACH_SMDK6410) - help - Say Y here to enable the use of the SMDK LEDs on the baseboard - for debugging of the state of the suspend and resume process. - - Note, this currently only works for S3C64XX based SMDK boards. - -config S3C2410_PM_CHECK - bool "S3C2410 PM Suspend Memory CRC" - depends on PM && CRC32 - help - Enable the PM code's memory area checksum over sleep. This option - will generate CRCs of all blocks of memory, and store them before - going to sleep. The blocks are then checked on resume for any - errors. - - Note, this can take several seconds depending on memory size - and CPU speed. - - See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> - -config S3C2410_PM_CHECK_CHUNKSIZE - int "S3C2410 PM Suspend CRC Chunksize (KiB)" - depends on PM && S3C2410_PM_CHECK - default 64 - help - Set the chunksize in Kilobytes of the CRC for checking memory - corruption over suspend and resume. A smaller value will mean that - the CRC data block will take more memory, but wil identify any - faults with better precision. - - See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> - -config S3C_LOWLEVEL_UART_PORT - int "S3C UART to use for low-level messages" - default 0 - help - Choice of which UART port to use for the low-level messages, - such as the `Uncompressing...` at start time. The value of - this configuration should be between zero and two. The port - must have been initialised by the boot-loader before use. - -# options for gpiolib support - -config S3C_GPIO_SPACE - int "Space between gpio banks" - default 0 - help - Add a number of spare GPIO entries between each bank for debugging - purposes. This allows any problems where an counter overflows from - one bank to another to be caught, at the expense of using a little - more memory. - -config S3C_GPIO_TRACK - bool - help - Internal configuration option to enable the s3c specific gpio - chip tracking if the platform requires it. - -config S3C_GPIO_PULL_UPDOWN - bool - help - Internal configuration to enable the correct GPIO pull helper - -config S3C_GPIO_PULL_DOWN - bool - help - Internal configuration to enable the correct GPIO pull helper - -config S3C_GPIO_PULL_UP - bool - help - Internal configuration to enable the correct GPIO pull helper - -config S3C_GPIO_CFG_S3C24XX - bool - help - Internal configuration to enable S3C24XX style GPIO configuration - functions. - -config S3C_GPIO_CFG_S3C64XX - bool - help - Internal configuration to enable S3C64XX style GPIO configuration - functions. - -config S5P_GPIO_CFG_S5PC1XX - bool - help - Internal configuration to enable S5PC1XX style GPIO configuration - functions. - -# DMA - -config S3C_DMA - bool - help - Internal configuration for S3C DMA core - -# device definitions to compile in - -config S3C_DEV_HSMMC - bool - help - Compile in platform device definitions for HSMMC code - -config S3C_DEV_HSMMC1 - bool - help - Compile in platform device definitions for HSMMC channel 1 - -config S3C_DEV_HSMMC2 - bool - help - Compile in platform device definitions for HSMMC channel 2 - -config S3C_DEV_I2C1 - bool - help - Compile in platform device definitions for I2C channel 1 - -config S3C_DEV_FB - bool - help - Compile in platform device definition for framebuffer - -config S3C_DEV_USB_HOST - bool - help - Compile in platform device definition for USB host. - -config S3C_DEV_USB_HSOTG - bool - help - Compile in platform device definition for USB high-speed OtG - -config S3C_DEV_NAND - bool - help - Compile in platform device definition for NAND controller - -endif |