5 files changed, 8 insertions, 8 deletions
diff --git a/arch/arm/plat-samsung/include/plat/clock.h b/arch/arm/plat-samsung/include/plat/clock.h
index 9a82b887491..983c578b827 100644
--- a/arch/arm/plat-samsung/include/plat/clock.h
+++ b/arch/arm/plat-samsung/include/plat/clock.h
@@ -21,7 +21,7 @@ struct clk;
  * @set_parent: set the clock's parent, see clk_set_parent().
  *
  * Group the common clock implementations together so that we
- * don't have to keep setting the same fiels again. We leave
+ * don't have to keep setting the same fields again. We leave
  * enable in struct clk.
  *
  * Adding an extra layer of indirection into the process should
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
index 5603db0b79b..3ad8386599c 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
@@ -114,7 +114,7 @@ extern unsigned s3c_gpio_getcfg_s3c24xx_a(struct s3c_gpio_chip *chip,
  * of control per GPIO, generally in the form of:
  *	0000 = Input
  *	0001 = Output
- *	others = Special functions (dependant on bank)
+ *	others = Special functions (dependent on bank)
  *
  * Note, since the code to deal with the case where there are two control
  * registers instead of one, we do not have a separate set of functions for
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
index 5e04fa6eda7..1762dcb4cb9 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-cfg.h
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
@@ -125,7 +125,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
  *
  * These values control the state of the weak pull-{up,down} resistors
  * available on most pins on the S3C series. Not all chips support both
- * up or down settings, and it may be dependant on the chip that is being
+ * up or down settings, and it may be dependent on the chip that is being
  * used to whether the particular mode is available.
  */
 #define S3C_GPIO_PULL_NONE	((__force s3c_gpio_pull_t)0x00)
@@ -138,7 +138,7 @@ extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
  * @pull: The configuration for the pull resistor.
  *
  * This function sets the state of the pull-{up,down} resistor for the
- * specified pin. It will return 0 if successfull, or a negative error
+ * specified pin. It will return 0 if successful, or a negative error
  * code if the pin cannot support the requested pull setting.
  *
  * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
@@ -202,7 +202,7 @@ extern s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin);
  * @drvstr: The new value of the driver strength
  *
  * This function sets the driver strength value for the specified pin.
- * It will return 0 if successfull, or a negative error code if the pin
+ * It will return 0 if successful, or a negative error code if the pin
  * cannot support the requested setting.
 */
 extern int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr);
diff --git a/arch/arm/plat-samsung/include/plat/gpio-core.h b/arch/arm/plat-samsung/include/plat/gpio-core.h
index dac35d0a711..8cad4cf19c3 100644
--- a/arch/arm/plat-samsung/include/plat/gpio-core.h
+++ b/arch/arm/plat-samsung/include/plat/gpio-core.h
@@ -108,7 +108,7 @@ extern void s3c_gpiolib_add(struct s3c_gpio_chip *chip);
  * of control per GPIO, generally in the form of:
  * 0000 = Input
  * 0001 = Output
- * others = Special functions (dependant on bank)
+ * others = Special functions (dependent on bank)
  *
  * Note, since the code to deal with the case where there are two control
  * registers instead of one, we do not have a separate set of function
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h
index b0bdf16549d..058e09654fe 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/plat-samsung/include/plat/sdhci.h
@@ -57,7 +57,7 @@ enum clk_types {
  * @cfg_gpio: Configure the GPIO for a specific card bit-width
  * @cfg_card: Configure the interface for a specific card and speed. This
  *            is necessary the controllers and/or GPIO blocks require the
- *	      changing of driver-strength and other controls dependant on
+ *	      changing of driver-strength and other controls dependent on
  *	      the card and speed of operation.
  *
  * Initialisation data specific to either the machine or the platform
@@ -108,7 +108,7 @@ extern struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata;
 extern struct s3c_sdhci_platdata s3c_hsmmc2_def_platdata;
 extern struct s3c_sdhci_platdata s3c_hsmmc3_def_platdata;
 
-/* Helper function availablity */
+/* Helper function availability */
 
 extern void s3c2416_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
 extern void s3c2416_setup_sdhci1_cfg_gpio(struct platform_device *, int w);