diff options
Diffstat (limited to 'arch/arm')
126 files changed, 916 insertions, 435 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 2c71a8f3535..3146ed3f6ec 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -195,8 +195,7 @@ config VECTORS_BASE The base address of exception vectors. config ARM_PATCH_PHYS_VIRT - bool "Patch physical to virtual translations at runtime (EXPERIMENTAL)" - depends on EXPERIMENTAL + bool "Patch physical to virtual translations at runtime" depends on !XIP_KERNEL && MMU depends on !ARCH_REALVIEW || !SPARSEMEM help @@ -1272,6 +1271,32 @@ config ARM_ERRATA_754327 This workaround defines cpu_relax() as smp_mb(), preventing correctly written polling loops from denying visibility of updates to memory. +config ARM_ERRATA_364296 + bool "ARM errata: Possible cache data corruption with hit-under-miss enabled" + depends on CPU_V6 && !SMP + help + This options enables the workaround for the 364296 ARM1136 + r0p2 erratum (possible cache data corruption with + hit-under-miss enabled). It sets the undocumented bit 31 in + the auxiliary control register and the FI bit in the control + register, thus disabling hit-under-miss without putting the + processor into full low interrupt latency mode. ARM11MPCore + is not affected. + +config ARM_ERRATA_764369 + bool "ARM errata: Data cache line maintenance operation by MVA may not succeed" + depends on CPU_V7 && SMP + help + This option enables the workaround for erratum 764369 + affecting Cortex-A9 MPCore with two or more processors (all + current revisions). Under certain timing circumstances, a data + cache line maintenance operation by MVA targeting an Inner + Shareable memory region may fail to proceed up to either the + Point of Coherency or to the Point of Unification of the + system. This workaround adds a DSB instruction before the + relevant cache maintenance functions and sets a specific bit + in the diagnostic control register of the SCU. + endmenu source "arch/arm/common/Kconfig" diff --git a/arch/arm/boot/compressed/mmcif-sh7372.c b/arch/arm/boot/compressed/mmcif-sh7372.c index b6f61d9a5a1..672ae95db5c 100644 --- a/arch/arm/boot/compressed/mmcif-sh7372.c +++ b/arch/arm/boot/compressed/mmcif-sh7372.c @@ -82,7 +82,7 @@ asmlinkage void mmc_loader(unsigned char *buf, unsigned long len) /* Disable clock to MMC hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) & (1 << 12), SMSTPCR3); + __raw_writel(__raw_readl(SMSTPCR3) | (1 << 12), SMSTPCR3); mmc_update_progress(MMC_PROGRESS_DONE); } diff --git a/arch/arm/boot/compressed/sdhi-sh7372.c b/arch/arm/boot/compressed/sdhi-sh7372.c index d403a8b24d7..d279294f238 100644 --- a/arch/arm/boot/compressed/sdhi-sh7372.c +++ b/arch/arm/boot/compressed/sdhi-sh7372.c @@ -85,7 +85,7 @@ asmlinkage void mmc_loader(unsigned short *buf, unsigned long len) goto err; /* Disable clock to SDHI1 hardware block */ - __raw_writel(__raw_readl(SMSTPCR3) & (1 << 13), SMSTPCR3); + __raw_writel(__raw_readl(SMSTPCR3) | (1 << 13), SMSTPCR3); mmc_update_progress(MMC_PROGRESS_DONE); diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra-harmony.dts index 4c053340ce3..e5818668d09 100644 --- a/arch/arm/boot/dts/tegra-harmony.dts +++ b/arch/arm/boot/dts/tegra-harmony.dts @@ -57,14 +57,14 @@ }; sdhci@c8000200 { - gpios = <&gpio 69 0>, /* cd, gpio PI5 */ - <&gpio 57 0>, /* wp, gpio PH1 */ - <&gpio 155 0>; /* power, gpio PT3 */ + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 155 0>; /* gpio PT3 */ }; sdhci@c8000600 { - gpios = <&gpio 58 0>, /* cd, gpio PH2 */ - <&gpio 59 0>, /* wp, gpio PH3 */ - <&gpio 70 0>; /* power, gpio PI6 */ + cd-gpios = <&gpio 58 0>; /* gpio PH2 */ + wp-gpios = <&gpio 59 0>; /* gpio PH3 */ + power-gpios = <&gpio 70 0>; /* gpio PI6 */ }; }; diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra-seaboard.dts index 1940cae0074..64cedca6fc7 100644 --- a/arch/arm/boot/dts/tegra-seaboard.dts +++ b/arch/arm/boot/dts/tegra-seaboard.dts @@ -21,8 +21,8 @@ }; sdhci@c8000400 { - gpios = <&gpio 69 0>, /* cd, gpio PI5 */ - <&gpio 57 0>, /* wp, gpio PH1 */ - <&gpio 70 0>; /* power, gpio PI6 */ + cd-gpios = <&gpio 69 0>; /* gpio PI5 */ + wp-gpios = <&gpio 57 0>; /* gpio PH1 */ + power-gpios = <&gpio 70 0>; /* gpio PI6 */ }; }; diff --git a/arch/arm/include/asm/futex.h b/arch/arm/include/asm/futex.h index 8c73900da9e..253cc86318b 100644 --- a/arch/arm/include/asm/futex.h +++ b/arch/arm/include/asm/futex.h @@ -25,17 +25,17 @@ #ifdef CONFIG_SMP -#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \ +#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \ smp_mb(); \ __asm__ __volatile__( \ - "1: ldrex %1, [%2]\n" \ + "1: ldrex %1, [%3]\n" \ " " insn "\n" \ - "2: strex %1, %0, [%2]\n" \ - " teq %1, #0\n" \ + "2: strex %2, %0, [%3]\n" \ + " teq %2, #0\n" \ " bne 1b\n" \ " mov %0, #0\n" \ - __futex_atomic_ex_table("%4") \ - : "=&r" (ret), "=&r" (oldval) \ + __futex_atomic_ex_table("%5") \ + : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \ : "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \ : "cc", "memory") @@ -73,14 +73,14 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr, #include <linux/preempt.h> #include <asm/domain.h> -#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \ +#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \ __asm__ __volatile__( \ - "1: " T(ldr) " %1, [%2]\n" \ + "1: " T(ldr) " %1, [%3]\n" \ " " insn "\n" \ - "2: " T(str) " %0, [%2]\n" \ + "2: " T(str) " %0, [%3]\n" \ " mov %0, #0\n" \ - __futex_atomic_ex_table("%4") \ - : "=&r" (ret), "=&r" (oldval) \ + __futex_atomic_ex_table("%5") \ + : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \ : "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \ : "cc", "memory") @@ -117,7 +117,7 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr) int cmp = (encoded_op >> 24) & 15; int oparg = (encoded_op << 8) >> 20; int cmparg = (encoded_op << 20) >> 20; - int oldval = 0, ret; + int oldval = 0, ret, tmp; if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28)) oparg = 1 << oparg; @@ -129,19 +129,19 @@ futex_atomic_op_inuser (int encoded_op, u32 __user *uaddr) switch (op) { case FUTEX_OP_SET: - __futex_atomic_op("mov %0, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("mov %0, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_ADD: - __futex_atomic_op("add %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("add %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_OR: - __futex_atomic_op("orr %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("orr %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; case FUTEX_OP_ANDN: - __futex_atomic_op("and %0, %1, %3", ret, oldval, uaddr, ~oparg); + __futex_atomic_op("and %0, %1, %4", ret, oldval, tmp, uaddr, ~oparg); break; case FUTEX_OP_XOR: - __futex_atomic_op("eor %0, %1, %3", ret, oldval, uaddr, oparg); + __futex_atomic_op("eor %0, %1, %4", ret, oldval, tmp, uaddr, oparg); break; default: ret = -ENOSYS; diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h index 16bd4803158..99a6ed7e1bf 100644 --- a/arch/arm/include/asm/hardware/cache-l2x0.h +++ b/arch/arm/include/asm/hardware/cache-l2x0.h @@ -45,8 +45,13 @@ #define L2X0_CLEAN_INV_LINE_PA 0x7F0 #define L2X0_CLEAN_INV_LINE_IDX 0x7F8 #define L2X0_CLEAN_INV_WAY 0x7FC -#define L2X0_LOCKDOWN_WAY_D 0x900 -#define L2X0_LOCKDOWN_WAY_I 0x904 +/* + * The lockdown registers repeat 8 times for L310, the L210 has only one + * D and one I lockdown register at 0x0900 and 0x0904. + */ +#define L2X0_LOCKDOWN_WAY_D_BASE 0x900 +#define L2X0_LOCKDOWN_WAY_I_BASE 0x904 +#define L2X0_LOCKDOWN_STRIDE 0x08 #define L2X0_TEST_OPERATION 0xF00 #define L2X0_LINE_DATA 0xF10 #define L2X0_LINE_TAG 0xF30 @@ -64,7 +69,7 @@ #define L2X0_AUX_CTRL_MASK 0xc0000fff #define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16 #define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17 -#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x3 << 17) +#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17) #define L2X0_AUX_CTRL_SHARE_OVERRIDE_SHIFT 22 #define L2X0_AUX_CTRL_NS_LOCKDOWN_SHIFT 26 #define L2X0_AUX_CTRL_NS_INT_CTRL_SHIFT 27 diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h index 67c70a31a1b..b7e82c4aced 100644 --- a/arch/arm/include/asm/pmu.h +++ b/arch/arm/include/asm/pmu.h @@ -41,7 +41,7 @@ struct arm_pmu_platdata { * encoded error on failure. */ extern struct platform_device * -reserve_pmu(enum arm_pmu_type device); +reserve_pmu(enum arm_pmu_type type); /** * release_pmu() - Relinquish control of the performance counters @@ -62,26 +62,26 @@ release_pmu(enum arm_pmu_type type); * the actual hardware initialisation. */ extern int -init_pmu(enum arm_pmu_type device); +init_pmu(enum arm_pmu_type type); #else /* CONFIG_CPU_HAS_PMU */ #include <linux/err.h> static inline struct platform_device * -reserve_pmu(enum arm_pmu_type device) +reserve_pmu(enum arm_pmu_type type) { return ERR_PTR(-ENODEV); } static inline int -release_pmu(struct platform_device *pdev) +release_pmu(enum arm_pmu_type type) { return -ENODEV; } static inline int -init_pmu(enum arm_pmu_type device) +init_pmu(enum arm_pmu_type type) { return -ENODEV; } diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h index 2c04ed5efeb..c60a2944f95 100644 --- a/arch/arm/include/asm/unistd.h +++ b/arch/arm/include/asm/unistd.h @@ -478,8 +478,8 @@ /* * Unimplemented (or alternatively implemented) syscalls */ -#define __IGNORE_fadvise64_64 1 -#define __IGNORE_migrate_pages 1 +#define __IGNORE_fadvise64_64 +#define __IGNORE_migrate_pages #endif /* __KERNEL__ */ #endif /* __ASM_ARM_UNISTD_H */ diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S index 80f7896cc01..9943e9e74a1 100644 --- a/arch/arm/kernel/calls.S +++ b/arch/arm/kernel/calls.S @@ -178,7 +178,7 @@ CALL(sys_ni_syscall) /* vm86 */ CALL(sys_ni_syscall) /* was sys_query_module */ CALL(sys_poll) - CALL(sys_nfsservctl) + CALL(sys_ni_syscall) /* was nfsservctl */ /* 170 */ CALL(sys_setresgid16) CALL(sys_getresgid16) CALL(sys_prctl) diff --git a/arch/arm/kernel/iwmmxt.S b/arch/arm/kernel/iwmmxt.S index 7fa3bb0d239..a08783823b3 100644 --- a/arch/arm/kernel/iwmmxt.S +++ b/arch/arm/kernel/iwmmxt.S @@ -195,10 +195,10 @@ ENTRY(iwmmxt_task_disable) @ enable access to CP0 and CP1 XSC(mrc p15, 0, r4, c15, c1, 0) - XSC(orr r4, r4, #0xf) + XSC(orr r4, r4, #0x3) XSC(mcr p15, 0, r4, c15, c1, 0) PJ4(mrc p15, 0, r4, c1, c0, 2) - PJ4(orr r4, r4, #0x3) + PJ4(orr r4, r4, #0xf) PJ4(mcr p15, 0, r4, c1, c0, 2) mov r0, #0 @ nothing to load @@ -313,7 +313,7 @@ ENTRY(iwmmxt_task_switch) teq r2, r3 @ next task owns it? movne pc, lr @ no: leave Concan disabled -1: @ flip Conan access +1: @ flip Concan access XSC(eor r1, r1, #0x3) XSC(mcr p15, 0, r1, c15, c1, 0) PJ4(eor r1, r1, #0xf) diff --git a/arch/arm/kernel/module.c b/arch/arm/kernel/module.c index 05b377616fd..cc2020c2c70 100644 --- a/arch/arm/kernel/module.c +++ b/arch/arm/kernel/module.c @@ -323,7 +323,11 @@ int module_finalize(const Elf32_Ehdr *hdr, const Elf_Shdr *sechdrs, #endif s = find_mod_section(hdr, sechdrs, ".alt.smp.init"); if (s && !is_smp()) +#ifdef CONFIG_SMP_ON_UP fixup_smp((void *)s->sh_addr, s->sh_size); +#else + return -EINVAL; +#endif return 0; } diff --git a/arch/arm/kernel/pmu.c b/arch/arm/kernel/pmu.c index 2b70709376c..c53474fe84d 100644 --- a/arch/arm/kernel/pmu.c +++ b/arch/arm/kernel/pmu.c @@ -31,7 +31,7 @@ static int __devinit pmu_register(struct platform_device *pdev, { if (type < 0 || type >= ARM_NUM_PMU_DEVICES) { pr_warning("received registration request for unknown " - "device %d\n", type); + "PMU device type %d\n", type); return -EINVAL; } @@ -112,17 +112,17 @@ static int __init register_pmu_driver(void) device_initcall(register_pmu_driver); struct platform_device * -reserve_pmu(enum arm_pmu_type device) +reserve_pmu(enum arm_pmu_type type) { struct platform_device *pdev; - if (test_and_set_bit_lock(device, &pmu_lock)) { + if (test_and_set_bit_lock(type, &pmu_lock)) { pdev = ERR_PTR(-EBUSY); - } else if (pmu_devices[device] == NULL) { - clear_bit_unlock(device, &pmu_lock); + } else if (pmu_devices[type] == NULL) { + clear_bit_unlock(type, &pmu_lock); pdev = ERR_PTR(-ENODEV); } else { - pdev = pmu_devices[device]; + pdev = pmu_devices[type]; } return pdev; @@ -130,11 +130,11 @@ reserve_pmu(enum arm_pmu_type device) EXPORT_SYMBOL_GPL(reserve_pmu); int -release_pmu(enum arm_pmu_type device) +release_pmu(enum arm_pmu_type type) { - if (WARN_ON(!pmu_devices[device])) + if (WARN_ON(!pmu_devices[type])) return -EINVAL; - clear_bit_unlock(device, &pmu_lock); + clear_bit_unlock(type, &pmu_lock); return 0; } EXPORT_SYMBOL_GPL(release_pmu); @@ -182,17 +182,17 @@ init_cpu_pmu(void) } int -init_pmu(enum arm_pmu_type device) +init_pmu(enum arm_pmu_type type) { int err = 0; - switch (device) { + switch (type) { case ARM_PMU_DEVICE_CPU: err = init_cpu_pmu(); break; default: - pr_warning("attempt to initialise unknown device %d\n", - device); + pr_warning("attempt to initialise PMU of unknown " + "type %d\n", type); err = -EINVAL; } diff --git a/arch/arm/kernel/relocate_kernel.S b/arch/arm/kernel/relocate_kernel.S index 9cf4cbf8f95..d0cdedf4864 100644 --- a/arch/arm/kernel/relocate_kernel.S +++ b/arch/arm/kernel/relocate_kernel.S @@ -57,7 +57,8 @@ relocate_new_kernel: mov r0,#0 ldr r1,kexec_mach_type ldr r2,kexec_boot_atags - mov pc,lr + ARM( mov pc, lr ) + THUMB( bx lr ) .align diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c index 70bca649e92..e514c76043b 100644 --- a/arch/arm/kernel/setup.c +++ b/arch/arm/kernel/setup.c @@ -280,18 +280,19 @@ static void __init cacheid_init(void) if (arch >= CPU_ARCH_ARMv6) { if ((cachetype & (7 << 29)) == 4 << 29) { /* ARMv7 register format */ + arch = CPU_ARCH_ARMv7; cacheid = CACHEID_VIPT_NONALIASING; if ((cachetype & (3 << 14)) == 1 << 14) cacheid |= CACHEID_ASID_TAGGED; - else if (cpu_has_aliasing_icache(CPU_ARCH_ARMv7)) - cacheid |= CACHEID_VIPT_I_ALIASING; - } else if (cachetype & (1 << 23)) { - cacheid = CACHEID_VIPT_ALIASING; } else { - cacheid = CACHEID_VIPT_NONALIASING; - if (cpu_has_aliasing_icache(CPU_ARCH_ARMv6)) - cacheid |= CACHEID_VIPT_I_ALIASING; + arch = CPU_ARCH_ARMv6; + if (cachetype & (1 << 23)) + cacheid = CACHEID_VIPT_ALIASING; + else + cacheid = CACHEID_VIPT_NONALIASING; } + if (cpu_has_aliasing_icache(arch)) + cacheid |= CACHEID_VIPT_I_ALIASING; } else { cacheid = CACHEID_VIVT; } diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c index 79ed5e7f204..7fcddb75c87 100644 --- a/arch/arm/kernel/smp_scu.c +++ b/arch/arm/kernel/smp_scu.c @@ -13,6 +13,7 @@ #include <asm/smp_scu.h> #include <asm/cacheflush.h> +#include <asm/cputype.h> #define SCU_CTRL 0x00 #define SCU_CONFIG 0x04 @@ -37,6 +38,15 @@ void __init scu_enable(void __iomem *scu_base) { u32 scu_ctrl; +#ifdef CONFIG_ARM_ERRATA_764369 + /* Cortex-A9 only */ + if ((read_cpuid(CPUID_ID) & 0xff0ffff0) == 0x410fc090) { + scu_ctrl = __raw_readl(scu_base + 0x30); + if (!(scu_ctrl & 1)) + __raw_writel(scu_ctrl | 0x1, scu_base + 0x30); + } +#endif + scu_ctrl = __raw_readl(scu_base + SCU_CTRL); /* already enabled? */ if (scu_ctrl & 1) diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c index 2c277d40cee..01c186222f3 100644 --- a/arch/arm/kernel/smp_twd.c +++ b/arch/arm/kernel/smp_twd.c @@ -137,8 +137,8 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk) clk->max_delta_ns = clockevent_delta2ns(0xffffffff, clk); clk->min_delta_ns = clockevent_delta2ns(0xf, clk); + clockevents_register_device(clk); + /* Make sure our local interrupt controller has this enabled */ gic_enable_ppi(clk->irq); - - clockevents_register_device(clk); } diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index bf977f8514f..4e66f62b8d4 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -23,8 +23,10 @@ #if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK) #define ARM_EXIT_KEEP(x) x +#define ARM_EXIT_DISCARD(x) #else #define ARM_EXIT_KEEP(x) +#define ARM_EXIT_DISCARD(x) x #endif OUTPUT_ARCH(arm) @@ -39,6 +41,11 @@ jiffies = jiffies_64 + 4; SECTIONS { /* + * XXX: The linker does not define how output sections are + * assigned to input sections when there are multiple statements + * matching the same input section name. There is no documented + * order of matching. + * * unwind exit sections must be discarded before the rest of the * unwind sections get included. */ @@ -47,6 +54,9 @@ SECTIONS *(.ARM.extab.exit.text) ARM_CPU_DISCARD(*(.ARM.exidx.cpuexit.text)) ARM_CPU_DISCARD(*(.ARM.extab.cpuexit.text)) + ARM_EXIT_DISCARD(EXIT_TEXT) + ARM_EXIT_DISCARD(EXIT_DATA) + EXIT_CALL #ifndef CONFIG_HOTPLUG *(.ARM.exidx.devexit.text) *(.ARM.extab.devexit.text) @@ -58,6 +68,8 @@ SECTIONS #ifndef CONFIG_SMP_ON_UP *(.alt.smp.init) #endif + *(.discard) + *(.discard.*) } #ifdef CONFIG_XIP_KERNEL @@ -279,9 +291,6 @@ SECTIONS STABS_DEBUG .comment 0 : { *(.comment) } - - /* Default discards */ - DISCARDS } /* diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index d522b47e30b..6c8e3b5f669 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -157,7 +157,7 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk), CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk), - CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc1_clk), + CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk), diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S index 6bd83ed90af..d87bfc397d3 100644 --- a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S +++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S @@ -8,7 +8,6 @@ * published by the Free Software Foundation. */ -#include <mach/hardware.h> #include <asm/hardware/entry-macro-gic.S> .macro disable_fiq diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h index 58bb03ae3cf..4f16c9b79f7 100644 --- a/arch/arm/mach-cns3xxx/include/mach/system.h +++ b/arch/arm/mach-cns3xxx/include/mach/system.h @@ -13,7 +13,6 @@ #include <linux/io.h> #include <asm/proc-fns.h> -#include <mach/hardware.h> static inline void arch_idle(void) { diff --git a/arch/arm/mach-cns3xxx/include/mach/uncompress.h b/arch/arm/mach-cns3xxx/include/mach/uncompress.h index de8ead9b91f..a91b6058ab4 100644 --- a/arch/arm/mach-cns3xxx/include/mach/uncompress.h +++ b/arch/arm/mach-cns3xxx/include/mach/uncompress.h @@ -8,7 +8,6 @@ */ #include <asm/mach-types.h> -#include <mach/hardware.h> #include <mach/cns3xxx.h> #define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00)) diff --git a/arch/arm/mach-cns3xxx/pcie.c b/arch/arm/mach-cns3xxx/pcie.c index 06fd25d70ae..0f8fca48a5e 100644 --- a/arch/arm/mach-cns3xxx/pcie.c +++ b/arch/arm/mach-cns3xxx/pcie.c @@ -49,7 +49,7 @@ static struct cns3xxx_pcie *sysdata_to_cnspci(void *sysdata) return &cns3xxx_pcie[root->domain]; } -static struct cns3xxx_pcie *pdev_to_cnspci(struct pci_dev *dev) +static struct cns3xxx_pcie *pdev_to_cnspci(const struct pci_dev *dev) { return sysdata_to_cnspci(dev->sysdata); } diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index bd5394537c8..008d51407cd 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -115,6 +115,32 @@ static struct spi_board_info da850evm_spi_info[] = { }, }; +#ifdef CONFIG_MTD +static void da850_evm_m25p80_notify_add(struct mtd_info *mtd) +{ + char *mac_addr = davinci_soc_info.emac_pdata->mac_addr; + size_t retlen; + + if (!strcmp(mtd->name, "MAC-Address")) { + mtd->read(mtd, 0, ETH_ALEN, &retlen, mac_addr); + if (retlen == ETH_ALEN) + pr_info("Read MAC addr from SPI Flash: %pM\n", + mac_addr); + } +} + +static struct mtd_notifier da850evm_spi_notifier = { + .add = da850_evm_m25p80_notify_add, +}; + +static void da850_evm_setup_mac_addr(void) +{ + register_mtd_user(&da850evm_spi_notifier); +} +#else +static void da850_evm_setup_mac_addr(void) { } +#endif + static struct mtd_partition da850_evm_norflash_partition[] = { { .name = "bootloaders + env", @@ -1244,6 +1270,8 @@ static __init void da850_evm_init(void) if (ret) pr_warning("da850_evm_init: sata registration failed: %d\n", ret); + + da850_evm_setup_mac_addr(); } #ifdef CONFIG_SERIAL_8250_CONSOLE diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h index 47fd0bc3d3e..fa59c097223 100644 --- a/arch/arm/mach-davinci/include/mach/psc.h +++ b/arch/arm/mach-davinci/include/mach/psc.h @@ -243,7 +243,7 @@ #define PSC_STATE_DISABLE 2 #define PSC_STATE_ENABLE 3 -#define MDSTAT_STATE_MASK 0x1f +#define MDSTAT_STATE_MASK 0x3f #define MDCTL_FORCE BIT(31) #ifndef __ASSEMBLER__ diff --git a/arch/arm/mach-davinci/sleep.S b/arch/arm/mach-davinci/sleep.S index fb5e72b532b..5f1e045a3ad 100644 --- a/arch/arm/mach-davinci/sleep.S +++ b/arch/arm/mach-davinci/sleep.S @@ -217,7 +217,11 @@ ddr2clk_stop_done: ENDPROC(davinci_ddr_psc_config) CACHE_FLUSH: - .word arm926_flush_kern_cache_all +#ifdef CONFIG_CPU_V6 + .word v6_flush_kern_cache_all +#else + .word arm926_flush_kern_cache_all +#endif ENTRY(davinci_cpu_suspend_sz) .word . - davinci_cpu_suspend diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c index 83dce859886..a9e0dae86a2 100644 --- a/arch/arm/mach-dove/common.c +++ b/arch/arm/mach-dove/common.c @@ -158,7 +158,7 @@ void __init dove_spi0_init(void) void __init dove_spi1_init(void) { - orion_spi_init(DOVE_SPI1_PHYS_BASE, get_tclk()); + orion_spi_1_init(DOVE_SPI1_PHYS_BASE, get_tclk()); } /***************************************************************************** diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h index 0eabec62cd9..f1397a13e76 100644 --- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h +++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h @@ -6,7 +6,7 @@ * TS72xx memory map: * * virt phys size - * febff000 22000000 4K model number register + * febff000 22000000 4K model number register (bits 0-2) * febfe000 22400000 4K options register * febfd000 22800000 4K options register #2 * febf9000 10800000 4K TS-5620 RTC index register @@ -20,6 +20,9 @@ #define TS72XX_MODEL_TS7200 0x00 #define TS72XX_MODEL_TS7250 0x01 #define TS72XX_MODEL_TS7260 0x02 +#define TS72XX_MODEL_TS7300 0x03 +#define TS72XX_MODEL_TS7400 0x04 +#define TS72XX_MODEL_MASK 0x07 #define TS72XX_OPTIONS_PHYS_BASE 0x22400000 @@ -51,19 +54,34 @@ #ifndef __ASSEMBLY__ +static inline int ts72xx_model(void) +{ + return __raw_readb(TS72XX_MODEL_VIRT_BASE) & TS72XX_MODEL_MASK; +} + static inline int board_is_ts7200(void) { - return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7200; + return ts72xx_model() == TS72XX_MODEL_TS7200; } static inline int board_is_ts7250(void) { - return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7250; + return ts72xx_model() == TS72XX_MODEL_TS7250; } static inline int board_is_ts7260(void) { - return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7260; + return ts72xx_model() == TS72XX_MODEL_TS7260; +} + +static inline int board_is_ts7300(void) +{ + return ts72xx_model() == TS72XX_MODEL_TS7300; +} + +static inline int board_is_ts7400(void) +{ + return ts72xx_model() == TS72XX_MODEL_TS7400; } static inline int is_max197_installed(void) diff --git a/arch/arm/mach-exynos4/clock.c b/arch/arm/mach-exynos4/clock.c index 851dea01857..86964d2e9e1 100644 --- a/arch/arm/mach-exynos4/clock.c +++ b/arch/arm/mach-exynos4/clock.c @@ -520,7 +520,7 @@ static struct clk init_clocks_off[] = { .ctrlbit = (1 << 21), }, { .name = "ac97", - .id = -1, + .devname = "samsung-ac97", .enable = exynos4_clk_ip_peril_ctrl, .ctrlbit = (1 << 27), }, { @@ -899,8 +899,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 28, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "exynos4-fimc.0", + .name = "sclk_cam0", .enable = exynos4_clksrc_mask_cam_ctrl, .ctrlbit = (1 << 16), }, @@ -909,8 +908,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 16, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "exynos4-fimc.1", + .name = "sclk_cam1", .enable = exynos4_clksrc_mask_cam_ctrl, .ctrlbit = (1 << 20), }, @@ -1160,7 +1158,7 @@ void __init_or_cpufreq exynos4_setup_clocks(void) vpllsrc = clk_get_rate(&clk_vpllsrc.clk); vpll = s5p_get_pll46xx(vpllsrc, __raw_readl(S5P_VPLL_CON0), - __raw_readl(S5P_VPLL_CON1), pll_4650); + __raw_readl(S5P_VPLL_CON1), pll_4650c); clk_fout_apll.ops = &exynos4_fout_apll_ops; clk_fout_mpll.rate = mpll; diff --git a/arch/arm/mach-exynos4/cpu.c b/arch/arm/mach-exynos4/cpu.c index 2d8a40c9e6e..746d6fc6d39 100644 --- a/arch/arm/mach-exynos4/cpu.c +++ b/arch/arm/mach-exynos4/cpu.c @@ -24,12 +24,13 @@ #include <plat/exynos4.h> #include <plat/adc-core.h> #include <plat/sdhci.h> -#include <plat/devs.h> #include <plat/fb-core.h> #include <plat/fimc-core.h> #include <plat/iic-core.h> +#include <plat/reset.h> #include <mach/regs-irq.h> +#include <mach/regs-pmu.h> extern int combiner_init(unsigned int combiner_nr, void __iomem *base, unsigned int irq_start); @@ -128,6 +129,11 @@ static void exynos4_idle(void) local_irq_enable(); } +static void exynos4_sw_reset(void) +{ + __raw_writel(0x1, S5P_SWRESET); +} + /* * exynos4_map_io * @@ -241,5 +247,8 @@ int __init exynos4_init(void) /* set idle function */ pm_idle = exynos4_idle; + /* set sw_reset function */ + s5p_reset_hook = exynos4_sw_reset; + return sysdev_register(&exynos4_sysdev); } diff --git a/arch/arm/mach-exynos4/include/mach/irqs.h b/arch/arm/mach-exynos4/include/mach/irqs.h index 934d2a49398..f8952f8f375 100644 --- a/arch/arm/mach-exynos4/include/mach/irqs.h +++ b/arch/arm/mach-exynos4/include/mach/irqs.h @@ -80,9 +80,8 @@ #define IRQ_HSMMC3 IRQ_SPI(76) #define IRQ_DWMCI IRQ_SPI(77) -#define IRQ_MIPICSI0 IRQ_SPI(78) - -#define IRQ_MIPICSI1 IRQ_SPI(80) +#define IRQ_MIPI_CSIS0 IRQ_SPI(78) +#define IRQ_MIPI_CSIS1 IRQ_SPI(80) #define IRQ_ONENAND_AUDI IRQ_SPI(82) #define IRQ_ROTATOR IRQ_SPI(83) diff --git a/arch/arm/mach-exynos4/include/mach/regs-pmu.h b/arch/arm/mach-exynos4/include/mach/regs-pmu.h index fa49bbb8e7b..cdf9b47c303 100644 --- a/arch/arm/mach-exynos4/include/mach/regs-pmu.h +++ b/arch/arm/mach-exynos4/include/mach/regs-pmu.h @@ -29,6 +29,8 @@ #define S5P_USE_STANDBY_WFE1 (1 << 25) #define S5P_USE_MASK ((0x3 << 16) | (0x3 << 24)) +#define S5P_SWRESET S5P_PMUREG(0x0400) + #define S5P_WAKEUP_STAT S5P_PMUREG(0x0600) #define S5P_EINT_WAKEUP_MASK S5P_PMUREG(0x0604) #define S5P_WAKEUP_MASK S5P_PMUREG(0x0608) diff --git a/arch/arm/mach-exynos4/irq-eint.c b/arch/arm/mach-exynos4/irq-eint.c index 9d87d2ac7f6..badb8c66fc9 100644 --- a/arch/arm/mach-exynos4/irq-eint.c +++ b/arch/arm/mach-exynos4/irq-eint.c @@ -23,6 +23,8 @@ #include <mach/regs-gpio.h> +#include <asm/mach/irq.h> + static DEFINE_SPINLOCK(eint_lock); static unsigned int eint0_15_data[16]; @@ -184,8 +186,11 @@ static inline void exynos4_irq_demux_eint(unsigned int start) static void exynos4_irq_demux_eint16_31(unsigned int irq, struct irq_desc *desc) { + struct irq_chip *chip = irq_get_chip(irq); + chained_irq_enter(chip, desc); exynos4_irq_demux_eint(IRQ_EINT(16)); exynos4_irq_demux_eint(IRQ_EINT(24)); + chained_irq_exit(chip, desc); } static void exynos4_irq_eint0_15(unsigned int irq, struct irq_desc *desc) @@ -193,6 +198,7 @@ static void exynos4_irq_eint0_15(unsigned int irq, struct irq_desc *desc) u32 *irq_data = irq_get_handler_data(irq); struct irq_chip *chip = irq_get_chip(irq); + chained_irq_enter(chip, desc); chip->irq_mask(&desc->irq_data); if (chip->irq_ack) @@ -201,6 +207,7 @@ static void exynos4_irq_eint0_15(unsigned int irq, struct irq_desc *desc) generic_handle_irq(*irq_data); chip->irq_unmask(&desc->irq_data); + chained_irq_exit(chip, desc); } int __init exynos4_init_irq_eint(void) diff --git a/arch/arm/mach-exynos4/mach-universal_c210.c b/arch/arm/mach-exynos4/mach-universal_c210.c index 0e280d12301..b3b5d891100 100644 --- a/arch/arm/mach-exynos4/mach-universal_c210.c +++ b/arch/arm/mach-exynos4/mach-universal_c210.c @@ -79,7 +79,7 @@ static struct s3c2410_uartcfg universal_uartcfgs[] __initdata = { }; static struct regulator_consumer_supply max8952_consumer = - REGULATOR_SUPPLY("vddarm", NULL); + REGULATOR_SUPPLY("vdd_arm", NULL); static struct max8952_platform_data universal_max8952_pdata __initdata = { .gpio_vid0 = EXYNOS4_GPX0(3), @@ -105,7 +105,7 @@ static struct max8952_platform_data universal_max8952_pdata __initdata = { }; static struct regulator_consumer_supply lp3974_buck1_consumer = - REGULATOR_SUPPLY("vddint", NULL); + REGULATOR_SUPPLY("vdd_int", NULL); static struct regulator_consumer_supply lp3974_buck2_consumer = REGULATOR_SUPPLY("vddg3d", NULL); diff --git a/arch/arm/mach-exynos4/mct.c b/arch/arm/mach-exynos4/mct.c index 1ae059b7ad7..ddd86864fb8 100644 --- a/arch/arm/mach-exynos4/mct.c +++ b/arch/arm/mach-exynos4/mct.c @@ -132,12 +132,18 @@ static cycle_t exynos4_frc_read(struct clocksource *cs) return ((cycle_t)hi << 32) | lo; } +static void exynos4_frc_resume(struct clocksource *cs) +{ + exynos4_mct_frc_start(0, 0); +} + struct clocksource mct_frc = { .name = "mct-frc", .rating = 400, .read = exynos4_frc_read, .mask = CLOCKSOURCE_MASK(64), .flags = CLOCK_SOURCE_IS_CONTINUOUS, + .resume = exynos4_frc_resume, }; static void __init exynos4_clocksource_init(void) @@ -389,9 +395,11 @@ static void exynos4_mct_tick_init(struct clock_event_device *evt) } /* Setup the local clock events for a CPU */ -void __cpuinit local_timer_setup(struct clock_event_device *evt) +int __cpuinit local_timer_setup(struct clock_event_device *evt) { exynos4_mct_tick_init(evt); + + return 0; } int local_timer_ack(void) diff --git a/arch/arm/mach-exynos4/platsmp.c b/arch/arm/mach-exynos4/platsmp.c index 7c2282c6ba8..df6ef1b2f98 100644 --- a/arch/arm/mach-exynos4/platsmp.c +++ b/arch/arm/mach-exynos4/platsmp.c @@ -106,6 +106,8 @@ void __cpuinit platform_secondary_init(unsigned int cpu) */ spin_lock(&boot_lock); spin_unlock(&boot_lock); + + set_cpu_online(cpu, true); } int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) diff --git a/arch/arm/mach-exynos4/setup-keypad.c b/arch/arm/mach-exynos4/setup-keypad.c index 1ee0ebff111..7862bfb5933 100644 --- a/arch/arm/mach-exynos4/setup-keypad.c +++ b/arch/arm/mach-exynos4/setup-keypad.c @@ -19,15 +19,16 @@ void samsung_keypad_cfg_gpio(unsigned int rows, unsigned int cols) if (rows > 8) { /* Set all the necessary GPX2 pins: KP_ROW[0~7] */ - s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), 8, S3C_GPIO_SFN(3)); + s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), 8, S3C_GPIO_SFN(3), + S3C_GPIO_PULL_UP); /* Set all the necessary GPX3 pins: KP_ROW[8~] */ - s3c_gpio_cfgrange_nopull(EXYNOS4_GPX3(0), (rows - 8), - S3C_GPIO_SFN(3)); + s3c_gpio_cfgall_range(EXYNOS4_GPX3(0), (rows - 8), + S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP); } else { /* Set all the necessary GPX2 pins: KP_ROW[x] */ - s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), rows, - S3C_GPIO_SFN(3)); + s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), rows, S3C_GPIO_SFN(3), + S3C_GPIO_PULL_UP); } /* Set all the necessary GPX1 pins to special-function 3: KP_COL[x] */ diff --git a/arch/arm/mach-exynos4/setup-usb-phy.c b/arch/arm/mach-exynos4/setup-usb-phy.c index 0883c1b824b..39aca045f66 100644 --- a/arch/arm/mach-exynos4/setup-usb-phy.c +++ b/arch/arm/mach-exynos4/setup-usb-phy.c @@ -82,7 +82,7 @@ static int exynos4_usb_phy1_init(struct platform_device *pdev) rstcon &= ~(HOST_LINK_PORT_SWRST_MASK | PHY1_SWRST_MASK); writel(rstcon, EXYNOS4_RSTCON); - udelay(50); + udelay(80); clk_disable(otg_clk); clk_put(otg_clk); diff --git a/arch/arm/mach-footbridge/Kconfig b/arch/arm/mach-footbridge/Kconfig index dc26fff22cf..c8e7afcf14e 100644 --- a/arch/arm/mach-footbridge/Kconfig +++ b/arch/arm/mach-footbridge/Kconfig @@ -62,6 +62,7 @@ config ARCH_EBSA285_HOST config ARCH_NETWINDER bool "NetWinder" select CLKSRC_I8253 + select CLKEVT_I8253 select FOOTBRIDGE_HOST select ISA select ISA_DMA diff --git a/arch/arm/mach-footbridge/dc21285.c b/arch/arm/mach-footbridge/dc21285.c index 1331fff51ae..18c32a5541d 100644 --- a/arch/arm/mach-footbridge/dc21285.c +++ b/arch/arm/mach-footbridge/dc21285.c @@ -18,6 +18,7 @@ #include <linux/irq.h> #include <linux/io.h> #include <linux/spinlock.h> +#include <video/vga.h> #include <asm/irq.h> #include <asm/system.h> diff --git a/arch/arm/mach-imx/clock-imx25.c b/arch/arm/mach-imx/clock-imx25.c index 0fc7ba56d61..e63e23504fe 100644 --- a/arch/arm/mach-imx/clock-imx25.c +++ b/arch/arm/mach-imx/clock-imx25.c @@ -331,6 +331,9 @@ int __init mx25_clocks_init(void) __raw_writel(__raw_readl(CRM_BASE+0x64) | (1 << 7) | (1 << 0), CRM_BASE + 0x64); + /* Clock source for gpt is ahb_div */ + __raw_writel(__raw_readl(CRM_BASE+0x64) & ~(1 << 5), CRM_BASE + 0x64); + mxc_timer_init(&gpt_clk, MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), 54); return 0; diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c index 87887ac5806..f851fe90368 100644 --- a/arch/arm/mach-imx/mach-cpuimx27.c +++ b/arch/arm/mach-imx/mach-cpuimx27.c @@ -310,7 +310,7 @@ static struct sys_timer eukrea_cpuimx27_timer = { .init = eukrea_cpuimx27_timer_init, }; -MACHINE_START(CPUIMX27, "EUKREA CPUIMX27") +MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27") .boot_params = MX27_PHYS_OFFSET + 0x100, .map_io = mx27_map_io, .init_early = imx27_init_early, diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c index f39a478ba1a..4bd083ba9af 100644 --- a/arch/arm/mach-imx/mach-cpuimx35.c +++ b/arch/arm/mach-imx/mach-cpuimx35.c @@ -192,7 +192,7 @@ struct sys_timer eukrea_cpuimx35_timer = { .init = eukrea_cpuimx35_timer_init, }; -MACHINE_START(EUKREA_CPUIMX35, "Eukrea CPUIMX35") +MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35") /* Maintainer: Eukrea Electromatique */ .boot_params = MX3x_PHYS_OFFSET + 0x100, .map_io = mx35_map_io, diff --git a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c index da36da52969..2442d5da883 100644 --- a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c +++ b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c @@ -161,7 +161,7 @@ static struct sys_timer eukrea_cpuimx25_timer = { .init = eukrea_cpuimx25_timer_init, }; -MACHINE_START(EUKREA_CPUIMX25, "Eukrea CPUIMX25") +MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25") /* Maintainer: Eukrea Electromatique */ .boot_params = MX25_PHYS_OFFSET + 0x100, .map_io = mx25_map_io, diff --git a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c index 6707de0ab71..6778f8193bc 100644 --- a/arch/arm/mach-imx/mach-imx27_visstrim_m10.c +++ b/arch/arm/mach-imx/mach-imx27_visstrim_m10.c @@ -30,6 +30,7 @@ #include <linux/input.h> #include <linux/gpio.h> #include <linux/delay.h> +#include <sound/tlv320aic32x4.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <asm/mach/time.h> @@ -196,6 +197,17 @@ static struct pca953x_platform_data visstrim_m10_pca9555_pdata = { .invert = 0, }; +static struct aic32x4_pdata visstrim_m10_aic32x4_pdata = { + .power_cfg = AIC32X4_PWR_MICBIAS_2075_LDOIN | + AIC32X4_PWR_AVDD_DVDD_WEAK_DISABLE | + AIC32X4_PWR_AIC32X4_LDO_ENABLE | + AIC32X4_PWR_CMMODE_LDOIN_RANGE_18_36 | + AIC32X4_PWR_CMMODE_HP_LDOIN_POWERED, + .micpga_routing = AIC32X4_MICPGA_ROUTE_LMIC_IN2R_10K | + AIC32X4_MICPGA_ROUTE_RMIC_IN1L_10K, + .swapdacs = false, +}; + static struct i2c_board_info visstrim_m10_i2c_devices[] = { { I2C_BOARD_INFO("pca9555", 0x20), @@ -203,6 +215,7 @@ static struct i2c_board_info visstrim_m10_i2c_devices[] = { }, { I2C_BOARD_INFO("tlv320aic32x4", 0x18), + .platform_data = &visstrim_m10_aic32x4_pdata, } }; diff --git a/arch/arm/mach-imx/mach-mx31ads.c b/arch/arm/mach-imx/mach-mx31ads.c index 0ce49478a47..29ca8907a78 100644 --- a/arch/arm/mach-imx/mach-mx31ads.c +++ b/arch/arm/mach-imx/mach-mx31ads.c @@ -468,7 +468,7 @@ static struct i2c_board_info __initdata mx31ads_i2c1_devices[] = { #endif }; -static void mxc_init_i2c(void) +static void __init mxc_init_i2c(void) { i2c_register_board_info(1, mx31ads_i2c1_devices, ARRAY_SIZE(mx31ads_i2c1_devices)); @@ -486,7 +486,7 @@ static unsigned int ssi_pins[] = { MX31_PIN_STXD5__STXD5, }; -static void mxc_init_audio(void) +static void __init mxc_init_audio(void) { imx31_add_imx_ssi(0, NULL); mxc_iomux_setup_multiple_pins(ssi_pins, ARRAY_SIZE(ssi_pins), "ssi"); diff --git a/arch/arm/mach-imx/mach-mx31lilly.c b/arch/arm/mach-imx/mach-mx31lilly.c index 750368ddf0f..126913ad106 100644 --- a/arch/arm/mach-imx/mach-mx31lilly.c +++ b/arch/arm/mach-imx/mach-mx31lilly.c @@ -192,7 +192,7 @@ static struct mxc_usbh_platform_data usbh2_pdata __initdata = { .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT, }; -static void lilly1131_usb_init(void) +static void __init lilly1131_usb_init(void) { imx31_add_mxc_ehci_hs(1, &usbh1_pdata); diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c index 2fbbdd5eac3..8cdc730dcb3 100644 --- a/arch/arm/mach-integrator/integrator_ap.c +++ b/arch/arm/mach-integrator/integrator_ap.c @@ -32,6 +32,7 @@ #include <linux/interrupt.h> #include <linux/io.h> #include <linux/mtd/physmap.h> +#include <video/vga.h> #include <mach/hardware.h> #include <mach/platform.h> @@ -154,6 +155,7 @@ static struct map_desc ap_io_desc[] __initdata = { static void __init ap_map_io(void) { iotable_init(ap_io_desc, ARRAY_SIZE(ap_io_desc)); + vga_base = PCI_MEMORY_VADDR; } #define INTEGRATOR_SC_VALID_INT 0x003fffff @@ -337,15 +339,15 @@ static unsigned long timer_reload; static void integrator_clocksource_init(u32 khz) { void __iomem *base = (void __iomem *)TIMER2_VA_BASE; - u32 ctrl = TIMER_CTRL_ENABLE; + u32 ctrl = TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC; if (khz >= 1500) { khz /= 16; - ctrl = TIMER_CTRL_DIV16; + ctrl |= TIMER_CTRL_DIV16; } - writel(ctrl, base + TIMER_CTRL); writel(0xffff, base + TIMER_LOAD); + writel(ctrl, base + TIMER_CTRL); clocksource_mmio_init(base + TIMER_VALUE, "timer2", khz * 1000, 200, 16, clocksource_mmio_readl_down); diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c index dd56bfb351e..11b86e5b71c 100644 --- a/arch/arm/mach-integrator/pci_v3.c +++ b/arch/arm/mach-integrator/pci_v3.c @@ -27,7 +27,6 @@ #include <linux/spinlock.h> #include <linux/init.h> #include <linux/io.h> -#include <video/vga.h> #include <mach/hardware.h> #include <mach/platform.h> @@ -505,7 +504,6 @@ void __init pci_v3_preinit(void) pcibios_min_io = 0x6000; pcibios_min_mem = 0x00100000; - vga_base = PCI_MEMORY_VADDR; /* * Hook in our fault handler for PCI errors diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c index c070c24255f..98e25d9aaab 100644 --- a/arch/arm/mach-mmp/gplugd.c +++ b/arch/arm/mach-mmp/gplugd.c @@ -16,16 +16,18 @@ #include <mach/gpio.h> #include <mach/pxa168.h> #include <mach/mfp-pxa168.h> -#include <mach/mfp-gplugd.h> #include "common.h" static unsigned long gplugd_pin_config[] __initdata = { /* UART3 */ - GPIO8_UART3_SOUT, - GPIO9_UART3_SIN, - GPI1O_UART3_CTS, - GPI11_UART3_RTS, + GPIO8_UART3_TXD, + GPIO9_UART3_RXD, + GPIO1O_UART3_CTS, + GPIO11_UART3_RTS, + + /* USB OTG PEN */ + GPIO18_GPIO, /* MMC2 */ GPIO28_MMC2_CMD, @@ -109,6 +111,12 @@ static unsigned long gplugd_pin_config[] __initdata = { GPIO105_CI2C_SDA, GPIO106_CI2C_SCL, + /* SPI NOR Flash on SSP2 */ + GPIO107_SSP2_RXD, + GPIO108_SSP2_TXD, + GPIO110_GPIO, /* SPI_CSn */ + GPIO111_SSP2_CLK, + /* Select JTAG */ GPIO109_GPIO, @@ -154,7 +162,7 @@ static void __init select_disp_freq(void) "frequency\n"); } else { gpio_direction_output(35, 1); - gpio_free(104); + gpio_free(35); } if (unlikely(gpio_request(85, "DISP_FREQ_SEL_2"))) { @@ -162,7 +170,7 @@ static void __init select_disp_freq(void) "frequency\n"); } else { gpio_direction_output(85, 0); - gpio_free(104); + gpio_free(85); } } diff --git a/arch/arm/mach-mmp/include/mach/mfp-gplugd.h b/arch/arm/mach-mmp/include/mach/mfp-gplugd.h deleted file mode 100644 index b8cf38d8560..00000000000 --- a/arch/arm/mach-mmp/include/mach/mfp-gplugd.h +++ /dev/null @@ -1,52 +0,0 @@ -/* - * linux/arch/arm/mach-mmp/include/mach/mfp-gplugd.h - * - * MFP definitions used in gplugD - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __MACH_MFP_GPLUGD_H -#define __MACH_MFP_GPLUGD_H - -#include <plat/mfp.h> -#include <mach/mfp.h> - -/* UART3 */ -#define GPIO8_UART3_SOUT MFP_CFG(GPIO8, AF2) -#define GPIO9_UART3_SIN MFP_CFG(GPIO9, AF2) -#define GPI1O_UART3_CTS MFP_CFG(GPIO10, AF2) -#define GPI11_UART3_RTS MFP_CFG(GPIO11, AF2) - -/* MMC2 */ -#define GPIO28_MMC2_CMD MFP_CFG_DRV(GPIO28, AF6, FAST) -#define GPIO29_MMC2_CLK MFP_CFG_DRV(GPIO29, AF6, FAST) -#define GPIO30_MMC2_DAT0 MFP_CFG_DRV(GPIO30, AF6, FAST) -#define GPIO31_MMC2_DAT1 MFP_CFG_DRV(GPIO31, AF6, FAST) -#define GPIO32_MMC2_DAT2 MFP_CFG_DRV(GPIO32, AF6, FAST) -#define GPIO33_MMC2_DAT3 MFP_CFG_DRV(GPIO33, AF6, FAST) - -/* I2S */ -#undef GPIO114_I2S_FRM -#undef GPIO115_I2S_BCLK - -#define GPIO114_I2S_FRM MFP_CFG_DRV(GPIO114, AF1, FAST) -#define GPIO115_I2S_BCLK MFP_CFG_DRV(GPIO115, AF1, FAST) -#define GPIO116_I2S_TXD MFP_CFG_DRV(GPIO116, AF1, FAST) - -/* MMC4 */ -#define GPIO125_MMC4_DAT3 MFP_CFG_DRV(GPIO125, AF7, FAST) -#define GPIO126_MMC4_DAT2 MFP_CFG_DRV(GPIO126, AF7, FAST) -#define GPIO127_MMC4_DAT1 MFP_CFG_DRV(GPIO127, AF7, FAST) -#define GPIO0_2_MMC4_DAT0 MFP_CFG_DRV(GPIO0_2, AF7, FAST) -#define GPIO1_2_MMC4_CMD MFP_CFG_DRV(GPIO1_2, AF7, FAST) -#define GPIO2_2_MMC4_CLK MFP_CFG_DRV(GPIO2_2, AF7, FAST) - -/* OTG GPIO */ -#define GPIO_USB_OTG_PEN 18 -#define GPIO_USB_OIDIR 20 - -/* Other GPIOs are 35, 84, 85 */ -#endif /* __MACH_MFP_GPLUGD_H */ diff --git a/arch/arm/mach-mmp/include/mach/mfp-pxa168.h b/arch/arm/mach-mmp/include/mach/mfp-pxa168.h index 8c782328b21..92aaa3c19d6 100644 --- a/arch/arm/mach-mmp/include/mach/mfp-pxa168.h +++ b/arch/arm/mach-mmp/include/mach/mfp-pxa168.h @@ -203,6 +203,10 @@ #define GPIO33_CF_nCD2 MFP_CFG(GPIO33, AF3) /* UART */ +#define GPIO8_UART3_TXD MFP_CFG(GPIO8, AF2) +#define GPIO9_UART3_RXD MFP_CFG(GPIO9, AF2) +#define GPIO1O_UART3_CTS MFP_CFG(GPIO10, AF2) +#define GPIO11_UART3_RTS MFP_CFG(GPIO11, AF2) #define GPIO88_UART2_TXD MFP_CFG(GPIO88, AF2) #define GPIO89_UART2_RXD MFP_CFG(GPIO89, AF2) #define GPIO107_UART1_TXD MFP_CFG_DRV(GPIO107, AF1, FAST) @@ -232,6 +236,22 @@ #define GPIO53_MMC1_CD MFP_CFG(GPIO53, AF1) #define GPIO46_MMC1_WP MFP_CFG(GPIO46, AF1) +/* MMC2 */ +#define GPIO28_MMC2_CMD MFP_CFG_DRV(GPIO28, AF6, FAST) +#define GPIO29_MMC2_CLK MFP_CFG_DRV(GPIO29, AF6, FAST) +#define GPIO30_MMC2_DAT0 MFP_CFG_DRV(GPIO30, AF6, FAST) +#define GPIO31_MMC2_DAT1 MFP_CFG_DRV(GPIO31, AF6, FAST) +#define GPIO32_MMC2_DAT2 MFP_CFG_DRV(GPIO32, AF6, FAST) +#define GPIO33_MMC2_DAT3 MFP_CFG_DRV(GPIO33, AF6, FAST) + +/* MMC4 */ +#define GPIO125_MMC4_DAT3 MFP_CFG_DRV(GPIO125, AF7, FAST) +#define GPIO126_MMC4_DAT2 MFP_CFG_DRV(GPIO126, AF7, FAST) +#define GPIO127_MMC4_DAT1 MFP_CFG_DRV(GPIO127, AF7, FAST) +#define GPIO0_2_MMC4_DAT0 MFP_CFG_DRV(GPIO0_2, AF7, FAST) +#define GPIO1_2_MMC4_CMD MFP_CFG_DRV(GPIO1_2, AF7, FAST) +#define GPIO2_2_MMC4_CLK MFP_CFG_DRV(GPIO2_2, AF7, FAST) + /* LCD */ #define GPIO84_LCD_CS MFP_CFG(GPIO84, AF1) #define GPIO60_LCD_DD0 MFP_CFG(GPIO60, AF1) @@ -269,11 +289,12 @@ #define GPIO106_CI2C_SCL MFP_CFG(GPIO106, AF1) /* I2S */ -#define GPIO113_I2S_MCLK MFP_CFG(GPIO113,AF6) -#define GPIO114_I2S_FRM MFP_CFG(GPIO114,AF1) -#define GPIO115_I2S_BCLK MFP_CFG(GPIO115,AF1) -#define GPIO116_I2S_RXD MFP_CFG(GPIO116,AF2) -#define GPIO117_I2S_TXD MFP_CFG(GPIO117,AF2) +#define GPIO113_I2S_MCLK MFP_CFG(GPIO113, AF6) +#define GPIO114_I2S_FRM MFP_CFG(GPIO114, AF1) +#define GPIO115_I2S_BCLK MFP_CFG(GPIO115, AF1) +#define GPIO116_I2S_RXD MFP_CFG(GPIO116, AF2) +#define GPIO116_I2S_TXD MFP_CFG(GPIO116, AF1) +#define GPIO117_I2S_TXD MFP_CFG(GPIO117, AF2) /* PWM */ #define GPIO96_PWM3_OUT MFP_CFG(GPIO96, AF1) @@ -324,4 +345,10 @@ #define GPIO101_MII_MDIO MFP_CFG(GPIO101, AF5) #define GPIO103_RX_DV MFP_CFG(GPIO103, AF5) +/* SSP2 */ +#define GPIO107_SSP2_RXD MFP_CFG(GPIO107, AF4) +#define GPIO108_SSP2_TXD MFP_CFG(GPIO108, AF4) +#define GPIO111_SSP2_CLK MFP_CFG(GPIO111, AF4) +#define GPIO112_SSP2_FRM MFP_CFG(GPIO112, AF4) + #endif /* __ASM_MACH_MFP_PXA168_H */ diff --git a/arch/arm/mach-mmp/time.c b/arch/arm/mach-mmp/time.c index 99833b9485c..4e91ee6e27c 100644 --- a/arch/arm/mach-mmp/time.c +++ b/arch/arm/mach-mmp/time.c @@ -51,12 +51,12 @@ static inline uint32_t timer_read(void) { int delay = 100; - __raw_writel(1, TIMERS_VIRT_BASE + TMR_CVWR(0)); + __raw_writel(1, TIMERS_VIRT_BASE + TMR_CVWR(1)); while (delay--) cpu_relax(); - return __raw_readl(TIMERS_VIRT_BASE + TMR_CVWR(0)); + return __raw_readl(TIMERS_VIRT_BASE + TMR_CVWR(1)); } unsigned long long notrace sched_clock(void) @@ -75,28 +75,51 @@ static irqreturn_t timer_interrupt(int irq, void *dev_id) { struct clock_event_device *c = dev_id; - /* disable and clear pending interrupt status */ - __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(0)); - __raw_writel(0x1, TIMERS_VIRT_BASE + TMR_ICR(0)); + /* + * Clear pending interrupt status. + */ + __raw_writel(0x01, TIMERS_VIRT_BASE + TMR_ICR(0)); + + /* + * Disable timer 0. + */ + __raw_writel(0x02, TIMERS_VIRT_BASE + TMR_CER); + c->event_handler(c); + return IRQ_HANDLED; } static int timer_set_next_event(unsigned long delta, struct clock_event_device *dev) { - unsigned long flags, next; + unsigned long flags; local_irq_save(flags); - /* clear pending interrupt status and enable */ + /* + * Disable timer 0. + */ + __raw_writel(0x02, TIMERS_VIRT_BASE + TMR_CER); + + /* + * Clear and enable timer match 0 interrupt. + */ __raw_writel(0x01, TIMERS_VIRT_BASE + TMR_ICR(0)); __raw_writel(0x01, TIMERS_VIRT_BASE + TMR_IER(0)); - next = timer_read() + delta; - __raw_writel(next, TIMERS_VIRT_BASE + TMR_TN_MM(0, 0)); + /* + * Setup new clockevent timer value. + */ + __raw_writel(delta - 1, TIMERS_VIRT_BASE + TMR_TN_MM(0, 0)); + + /* + * Enable timer 0. + */ + __raw_writel(0x03, TIMERS_VIRT_BASE + TMR_CER); local_irq_restore(flags); + return 0; } @@ -145,23 +168,26 @@ static struct clocksource cksrc = { static void __init timer_config(void) { uint32_t ccr = __raw_readl(TIMERS_VIRT_BASE + TMR_CCR); - uint32_t cer = __raw_readl(TIMERS_VIRT_BASE + TMR_CER); - uint32_t cmr = __raw_readl(TIMERS_VIRT_BASE + TMR_CMR); - __raw_writel(cer & ~0x1, TIMERS_VIRT_BASE + TMR_CER); /* disable */ + __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_CER); /* disable */ - ccr &= (cpu_is_mmp2()) ? TMR_CCR_CS_0(0) : TMR_CCR_CS_0(3); + ccr &= (cpu_is_mmp2()) ? (TMR_CCR_CS_0(0) | TMR_CCR_CS_1(0)) : + (TMR_CCR_CS_0(3) | TMR_CCR_CS_1(3)); __raw_writel(ccr, TIMERS_VIRT_BASE + TMR_CCR); - /* free-running mode */ - __raw_writel(cmr | 0x01, TIMERS_VIRT_BASE + TMR_CMR); + /* set timer 0 to periodic mode, and timer 1 to free-running mode */ + __raw_writel(0x2, TIMERS_VIRT_BASE + TMR_CMR); - __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_PLCR(0)); /* free-running */ + __raw_writel(0x1, TIMERS_VIRT_BASE + TMR_PLCR(0)); /* periodic */ __raw_writel(0x7, TIMERS_VIRT_BASE + TMR_ICR(0)); /* clear status */ __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(0)); - /* enable timer counter */ - __raw_writel(cer | 0x01, TIMERS_VIRT_BASE + TMR_CER); + __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_PLCR(1)); /* free-running */ + __raw_writel(0x7, TIMERS_VIRT_BASE + TMR_ICR(1)); /* clear status */ + __raw_writel(0x0, TIMERS_VIRT_BASE + TMR_IER(1)); + + /* enable timer 1 counter */ + __raw_writel(0x2, TIMERS_VIRT_BASE + TMR_CER); } static struct irqaction timer_irq = { diff --git a/arch/arm/mach-mx5/board-cpuimx51.c b/arch/arm/mach-mx5/board-cpuimx51.c index 7c893fa7026..68934ea8725 100644 --- a/arch/arm/mach-mx5/board-cpuimx51.c +++ b/arch/arm/mach-mx5/board-cpuimx51.c @@ -81,7 +81,7 @@ static struct plat_serial8250_port serial_platform_data[] = { .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP, }, { .mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x2000000), - .irq = irq_to_gpio(CPUIMX51_QUARTD_GPIO), + .irq = gpio_to_irq(CPUIMX51_QUARTD_GPIO), .irqflags = IRQF_TRIGGER_HIGH, .uartclk = CPUIMX51_QUART_XTAL, .regshift = CPUIMX51_QUART_REGSHIFT, diff --git a/arch/arm/mach-mx5/board-mx51_babbage.c b/arch/arm/mach-mx5/board-mx51_babbage.c index e400b09109c..11b0ff67f89 100644 --- a/arch/arm/mach-mx5/board-mx51_babbage.c +++ b/arch/arm/mach-mx5/board-mx51_babbage.c @@ -369,7 +369,7 @@ static void __init mx51_babbage_init(void) ARRAY_SIZE(mx51babbage_pads)); imx51_add_imx_uart(0, &uart_pdata); - imx51_add_imx_uart(1, &uart_pdata); + imx51_add_imx_uart(1, NULL); imx51_add_imx_uart(2, &uart_pdata); babbage_fec_reset(); diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c index f70700dc0ec..551daf85ff8 100644 --- a/arch/arm/mach-mx5/board-mx51_efikamx.c +++ b/arch/arm/mach-mx5/board-mx51_efikamx.c @@ -108,9 +108,9 @@ static void __init mx51_efikamx_board_id(void) gpio_request(EFIKAMX_PCBID2, "pcbid2"); gpio_direction_input(EFIKAMX_PCBID2); - id = gpio_get_value(EFIKAMX_PCBID0); - id |= gpio_get_value(EFIKAMX_PCBID1) << 1; - id |= gpio_get_value(EFIKAMX_PCBID2) << 2; + id = gpio_get_value(EFIKAMX_PCBID0) ? 1 : 0; + id |= (gpio_get_value(EFIKAMX_PCBID1) ? 1 : 0) << 1; + id |= (gpio_get_value(EFIKAMX_PCBID2) ? 1 : 0) << 2; switch (id) { case 7: diff --git a/arch/arm/mach-mx5/board-mx51_efikasb.c b/arch/arm/mach-mx5/board-mx51_efikasb.c index 2e4d9d32a87..8a9bca22beb 100644 --- a/arch/arm/mach-mx5/board-mx51_efikasb.c +++ b/arch/arm/mach-mx5/board-mx51_efikasb.c @@ -156,23 +156,24 @@ static struct gpio_keys_button mx51_efikasb_keys[] = { { .code = KEY_POWER, .gpio = EFIKASB_PWRKEY, - .type = EV_PWR, + .type = EV_KEY, .desc = "Power Button", .wakeup = 1, - .debounce_interval = 10, /* ms */ + .active_low = 1, }, { .code = SW_LID, .gpio = EFIKASB_LID, .type = EV_SW, .desc = "Lid Switch", + .active_low = 1, }, { - /* SW_RFKILLALL vs KEY_RFKILL ? */ - .code = SW_RFKILL_ALL, + .code = KEY_RFKILL, .gpio = EFIKASB_RFKILL, - .type = EV_SW, + .type = EV_KEY, .desc = "rfkill", + .active_low = 1, }, }; @@ -224,8 +225,8 @@ static void __init mx51_efikasb_board_id(void) gpio_request(EFIKASB_PCBID1, "pcb id1"); gpio_direction_input(EFIKASB_PCBID1); - id = gpio_get_value(EFIKASB_PCBID0); - id |= gpio_get_value(EFIKASB_PCBID1) << 1; + id = gpio_get_value(EFIKASB_PCBID0) ? 1 : 0; + id |= (gpio_get_value(EFIKASB_PCBID1) ? 1 : 0) << 1; switch (id) { default: diff --git a/arch/arm/mach-mx5/clock-mx51-mx53.c b/arch/arm/mach-mx5/clock-mx51-mx53.c index 7f20308c4db..f7bf996f463 100644 --- a/arch/arm/mach-mx5/clock-mx51-mx53.c +++ b/arch/arm/mach-mx5/clock-mx51-mx53.c @@ -271,7 +271,11 @@ static int _clk_pll_enable(struct clk *clk) int i = 0; pllbase = _get_pll_base(clk); - reg = __raw_readl(pllbase + MXC_PLL_DP_CTL) | MXC_PLL_DP_CTL_UPEN; + reg = __raw_readl(pllbase + MXC_PLL_DP_CTL); + if (reg & MXC_PLL_DP_CTL_UPEN) + return 0; + + reg |= MXC_PLL_DP_CTL_UPEN; __raw_writel(reg, pllbase + MXC_PLL_DP_CTL); /* Wait for lock */ diff --git a/arch/arm/mach-mx5/mx51_efika.c b/arch/arm/mach-mx5/mx51_efika.c index 4435e03cea5..c9209454807 100644 --- a/arch/arm/mach-mx5/mx51_efika.c +++ b/arch/arm/mach-mx5/mx51_efika.c @@ -186,7 +186,7 @@ static int initialize_usbh1_port(struct platform_device *pdev) mdelay(10); - return mx51_initialize_usb_hw(0, MXC_EHCI_ITC_NO_THRESHOLD); + return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_ITC_NO_THRESHOLD); } static struct mxc_usbh_platform_data usbh1_config = { diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 4ae6257b39a..57b66d590c5 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -7,7 +7,6 @@ config ARCH_OMAP2PLUS_TYPICAL default y select AEABI select REGULATOR - select PM select PM_RUNTIME select VFP select NEON if ARCH_OMAP3 || ARCH_OMAP4 diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c index 5f2b55ff04f..933e9353cb3 100644 --- a/arch/arm/mach-omap2/board-am3517crane.c +++ b/arch/arm/mach-omap2/board-am3517crane.c @@ -45,8 +45,6 @@ static struct omap_board_config_kernel am3517_crane_config[] __initdata = { static struct omap_board_mux board_mux[] __initdata = { { .reg_offset = OMAP_MUX_TERMINATOR }, }; -#else -#define board_mux NULL #endif static void __init am3517_crane_init_early(void) diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 32f5f895568..3ae16b4e3f5 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -491,23 +491,22 @@ static void __init beagle_opp_init(void) /* Custom OPP enabled for all xM versions */ if (cpu_is_omap3630()) { - struct omap_hwmod *mh = omap_hwmod_lookup("mpu"); - struct omap_hwmod *dh = omap_hwmod_lookup("iva"); - struct device *dev; + struct device *mpu_dev, *iva_dev; - if (!mh || !dh) { + mpu_dev = omap2_get_mpuss_device(); + iva_dev = omap2_get_iva_device(); + + if (!mpu_dev || !iva_dev) { pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n", - __func__, mh, dh); + __func__, mpu_dev, iva_dev); return; } /* Enable MPU 1GHz and lower opps */ - dev = &mh->od->pdev.dev; - r = opp_enable(dev, 800000000); + r = opp_enable(mpu_dev, 800000000); /* TODO: MPU 1GHz needs SR and ABB */ /* Enable IVA 800MHz and lower opps */ - dev = &dh->od->pdev.dev; - r |= opp_enable(dev, 660000000); + r |= opp_enable(iva_dev, 660000000); /* TODO: DSP 800MHz needs SR and ABB */ if (r) { pr_err("%s: failed to enable higher opp %d\n", @@ -516,10 +515,8 @@ static void __init beagle_opp_init(void) * Cleanup - disable the higher freqs - we dont care * about the results */ - dev = &mh->od->pdev.dev; - opp_disable(dev, 800000000); - dev = &dh->od->pdev.dev; - opp_disable(dev, 660000000); + opp_disable(mpu_dev, 800000000); + opp_disable(iva_dev, 660000000); } } return; diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c index ffd55b1c439..b9b84468314 100644 --- a/arch/arm/mach-omap2/clock3xxx_data.c +++ b/arch/arm/mach-omap2/clock3xxx_data.c @@ -3078,6 +3078,7 @@ static struct clk gpt12_fck = { .name = "gpt12_fck", .ops = &clkops_null, .parent = &secure_32k_fck, + .clkdm_name = "wkup_clkdm", .recalc = &followparent_recalc, }; @@ -3085,6 +3086,7 @@ static struct clk wdt1_fck = { .name = "wdt1_fck", .ops = &clkops_null, .parent = &secure_32k_fck, + .clkdm_name = "wkup_clkdm", .recalc = &followparent_recalc, }; diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c index 2af0e3f00ce..c0b6fbda340 100644 --- a/arch/arm/mach-omap2/clock44xx_data.c +++ b/arch/arm/mach-omap2/clock44xx_data.c @@ -3376,10 +3376,18 @@ int __init omap4xxx_clk_init(void) } else if (cpu_is_omap446x()) { cpu_mask = RATE_IN_4460; cpu_clkflg = CK_446X; + } else { + return 0; } clk_init(&omap2_clk_functions); - omap2_clk_disable_clkdm_control(); + + /* + * Must stay commented until all OMAP SoC drivers are + * converted to runtime PM, or drivers may start crashing + * + * omap2_clk_disable_clkdm_control(); + */ for (c = omap44xx_clks; c < omap44xx_clks + ARRAY_SIZE(omap44xx_clks); c++) diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c index ab7db083f97..8f0890685d7 100644 --- a/arch/arm/mach-omap2/clockdomain.c +++ b/arch/arm/mach-omap2/clockdomain.c @@ -747,6 +747,7 @@ int clkdm_wakeup(struct clockdomain *clkdm) spin_lock_irqsave(&clkdm->lock, flags); clkdm->_flags &= ~_CLKDM_FLAG_HWSUP_ENABLED; ret = arch_clkdm->clkdm_wakeup(clkdm); + ret |= pwrdm_state_switch(clkdm->pwrdm.ptr); spin_unlock_irqrestore(&clkdm->lock, flags); return ret; } @@ -818,6 +819,7 @@ void clkdm_deny_idle(struct clockdomain *clkdm) spin_lock_irqsave(&clkdm->lock, flags); clkdm->_flags &= ~_CLKDM_FLAG_HWSUP_ENABLED; arch_clkdm->clkdm_deny_idle(clkdm); + pwrdm_state_switch(clkdm->pwrdm.ptr); spin_unlock_irqrestore(&clkdm->lock, flags); } diff --git a/arch/arm/mach-omap2/cminst44xx.h b/arch/arm/mach-omap2/cminst44xx.h index f2ea6453ade..a018a732787 100644 --- a/arch/arm/mach-omap2/cminst44xx.h +++ b/arch/arm/mach-omap2/cminst44xx.h @@ -18,13 +18,36 @@ extern void omap4_cminst_clkdm_force_sleep(u8 part, s16 inst, u16 cdoffs); extern void omap4_cminst_clkdm_force_wakeup(u8 part, s16 inst, u16 cdoffs); extern int omap4_cminst_wait_module_ready(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs); -extern int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs); + +# ifdef CONFIG_ARCH_OMAP4 +extern int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, + u16 clkctrl_offs); extern void omap4_cminst_module_enable(u8 mode, u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs); extern void omap4_cminst_module_disable(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_offs); +# else + +static inline int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, + u16 clkctrl_offs) +{ + return 0; +} + +static inline void omap4_cminst_module_enable(u8 mode, u8 part, u16 inst, + s16 cdoffs, u16 clkctrl_offs) +{ +} + +static inline void omap4_cminst_module_disable(u8 part, u16 inst, s16 cdoffs, + u16 clkctrl_offs) +{ +} + +# endif + /* * In an ideal world, we would not export these low-level functions, * but this will probably take some time to fix properly diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index c7fb22abc21..655e9480eb9 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -821,11 +821,10 @@ static void __init omap_mux_set_cmdline_signals(void) if (!omap_mux_options) return; - options = kmalloc(strlen(omap_mux_options) + 1, GFP_KERNEL); + options = kstrdup(omap_mux_options, GFP_KERNEL); if (!options) return; - strcpy(options, omap_mux_options); next_opt = options; while ((token = strsep(&next_opt, ",")) != NULL) { @@ -855,24 +854,19 @@ static int __init omap_mux_copy_names(struct omap_mux *src, for (i = 0; i < OMAP_MUX_NR_MODES; i++) { if (src->muxnames[i]) { - dst->muxnames[i] = - kmalloc(strlen(src->muxnames[i]) + 1, - GFP_KERNEL); + dst->muxnames[i] = kstrdup(src->muxnames[i], + GFP_KERNEL); if (!dst->muxnames[i]) goto free; - strcpy(dst->muxnames[i], src->muxnames[i]); } } #ifdef CONFIG_DEBUG_FS for (i = 0; i < OMAP_MUX_NR_SIDES; i++) { if (src->balls[i]) { - dst->balls[i] = - kmalloc(strlen(src->balls[i]) + 1, - GFP_KERNEL); + dst->balls[i] = kstrdup(src->balls[i], GFP_KERNEL); if (!dst->balls[i]) goto free; - strcpy(dst->balls[i], src->balls[i]); } } #endif diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c index 16743c7d6e8..408193d8e04 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c @@ -192,6 +192,7 @@ static struct omap_hwmod_addr_space omap2430_usbhsotg_addrs[] = { .pa_end = OMAP243X_HS_BASE + SZ_4K - 1, .flags = ADDR_TYPE_RT }, + { } }; /* l4_core ->usbhsotg interface */ diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 3feb35911a3..472bf22d5e8 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -130,7 +130,6 @@ int omap_set_pwrdm_state(struct powerdomain *pwrdm, u32 state) } else { hwsup = clkdm_in_hwsup(pwrdm->pwrdm_clkdms[0]); clkdm_wakeup(pwrdm->pwrdm_clkdms[0]); - pwrdm_wait_transition(pwrdm); sleep_switch = FORCEWAKEUP_SWITCH; } } @@ -156,7 +155,6 @@ int omap_set_pwrdm_state(struct powerdomain *pwrdm, u32 state) return ret; } - pwrdm_wait_transition(pwrdm); pwrdm_state_switch(pwrdm); err: return ret; diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index 9af08473bf1..ef71fdd40fc 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -195,28 +195,35 @@ static int _pwrdm_post_transition_cb(struct powerdomain *pwrdm, void *unused) /** * pwrdm_init - set up the powerdomain layer - * @pwrdm_list: array of struct powerdomain pointers to register + * @pwrdms: array of struct powerdomain pointers to register * @custom_funcs: func pointers for arch specific implementations * - * Loop through the array of powerdomains @pwrdm_list, registering all - * that are available on the current CPU. If pwrdm_list is supplied - * and not null, all of the referenced powerdomains will be - * registered. No return value. XXX pwrdm_list is not really a - * "list"; it is an array. Rename appropriately. + * Loop through the array of powerdomains @pwrdms, registering all + * that are available on the current CPU. Also, program all + * powerdomain target state as ON; this is to prevent domains from + * hitting low power states (if bootloader has target states set to + * something other than ON) and potentially even losing context while + * PM is not fully initialized. The PM late init code can then program + * the desired target state for all the power domains. No return + * value. */ -void pwrdm_init(struct powerdomain **pwrdm_list, struct pwrdm_ops *custom_funcs) +void pwrdm_init(struct powerdomain **pwrdms, struct pwrdm_ops *custom_funcs) { struct powerdomain **p = NULL; + struct powerdomain *temp_p; if (!custom_funcs) WARN(1, "powerdomain: No custom pwrdm functions registered\n"); else arch_pwrdm = custom_funcs; - if (pwrdm_list) { - for (p = pwrdm_list; *p; p++) + if (pwrdms) { + for (p = pwrdms; *p; p++) _pwrdm_register(*p); } + + list_for_each_entry(temp_p, &pwrdm_list, node) + pwrdm_set_next_pwrst(temp_p, PWRDM_POWER_ON); } /** diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c index 2ce2fb7664b..34c01a7de81 100644 --- a/arch/arm/mach-omap2/smartreflex.c +++ b/arch/arm/mach-omap2/smartreflex.c @@ -621,7 +621,7 @@ void sr_disable(struct voltagedomain *voltdm) sr_v2_disable(sr); } - pm_runtime_put_sync(&sr->pdev->dev); + pm_runtime_put_sync_suspend(&sr->pdev->dev); } /** @@ -860,6 +860,7 @@ static int __init omap_sr_probe(struct platform_device *pdev) irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); pm_runtime_enable(&pdev->dev); + pm_runtime_irq_safe(&pdev->dev); sr_info->pdev = pdev; sr_info->srid = pdev->id; diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index e9640728239..cf1de7d2630 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -293,7 +293,8 @@ static void __init omap2_gp_clocksource_init(int gptimer_id, pr_info("OMAP clocksource: GPTIMER%d at %lu Hz\n", gptimer_id, clksrc.rate); - __omap_dm_timer_load_start(clksrc.io_base, OMAP_TIMER_CTRL_ST, 0, 1); + __omap_dm_timer_load_start(clksrc.io_base, + OMAP_TIMER_CTRL_ST | OMAP_TIMER_CTRL_AR, 0, 1); init_sched_clock(&cd, dmtimer_update_sched_clock, 32, clksrc.rate); if (clocksource_register_hz(&clocksource_gpt, clksrc.rate)) diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 2543342dbcc..daa056ed873 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -48,14 +48,7 @@ void __init omap_pmic_init(int bus, u32 clkrate, omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); } -static struct twl4030_usb_data omap4_usb_pdata = { - .phy_init = omap4430_phy_init, - .phy_exit = omap4430_phy_exit, - .phy_power = omap4430_phy_power, - .phy_set_clock = omap4430_phy_set_clk, - .phy_suspend = omap4430_phy_suspend, -}; - +#if defined(CONFIG_ARCH_OMAP3) static struct twl4030_usb_data omap3_usb_pdata = { .usb_mode = T2_USB_MODE_ULPI, }; @@ -122,6 +115,45 @@ static struct regulator_init_data omap3_vpll2_idata = { .consumer_supplies = omap3_vpll2_supplies, }; +void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, + u32 pdata_flags, u32 regulators_flags) +{ + if (!pmic_data->irq_base) + pmic_data->irq_base = TWL4030_IRQ_BASE; + if (!pmic_data->irq_end) + pmic_data->irq_end = TWL4030_IRQ_END; + + /* Common platform data configurations */ + if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb) + pmic_data->usb = &omap3_usb_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci) + pmic_data->bci = &omap3_bci_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc) + pmic_data->madc = &omap3_madc_pdata; + + if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio) + pmic_data->audio = &omap3_audio_pdata; + + /* Common regulator configurations */ + if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac) + pmic_data->vdac = &omap3_vdac_idata; + + if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2) + pmic_data->vpll2 = &omap3_vpll2_idata; +} +#endif /* CONFIG_ARCH_OMAP3 */ + +#if defined(CONFIG_ARCH_OMAP4) +static struct twl4030_usb_data omap4_usb_pdata = { + .phy_init = omap4430_phy_init, + .phy_exit = omap4430_phy_exit, + .phy_power = omap4430_phy_power, + .phy_set_clock = omap4430_phy_set_clk, + .phy_suspend = omap4430_phy_suspend, +}; + static struct regulator_init_data omap4_vdac_idata = { .constraints = { .min_uV = 1800000, @@ -273,32 +305,4 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data, !pmic_data->clk32kg) pmic_data->clk32kg = &omap4_clk32kg_idata; } - -void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, - u32 pdata_flags, u32 regulators_flags) -{ - if (!pmic_data->irq_base) - pmic_data->irq_base = TWL4030_IRQ_BASE; - if (!pmic_data->irq_end) - pmic_data->irq_end = TWL4030_IRQ_END; - - /* Common platform data configurations */ - if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb) - pmic_data->usb = &omap3_usb_pdata; - - if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci) - pmic_data->bci = &omap3_bci_pdata; - - if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc) - pmic_data->madc = &omap3_madc_pdata; - - if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio) - pmic_data->audio = &omap3_audio_pdata; - - /* Common regulator configurations */ - if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac) - pmic_data->vdac = &omap3_vdac_idata; - - if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2) - pmic_data->vpll2 = &omap3_vpll2_idata; -} +#endif /* CONFIG_ARCH_OMAP4 */ diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c index a6eddae82a0..c105556a0ee 100644 --- a/arch/arm/mach-orion5x/dns323-setup.c +++ b/arch/arm/mach-orion5x/dns323-setup.c @@ -77,7 +77,7 @@ static int __init dns323_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) /* * Check for devices with hard-wired IRQs. */ - irq = orion5x_pci_map_irq(const dev, slot, pin); + irq = orion5x_pci_map_irq(dev, slot, pin); if (irq != -1) return irq; diff --git a/arch/arm/mach-orion5x/pci.c b/arch/arm/mach-orion5x/pci.c index 28b8760ab9f..bc4a920e26e 100644 --- a/arch/arm/mach-orion5x/pci.c +++ b/arch/arm/mach-orion5x/pci.c @@ -14,6 +14,7 @@ #include <linux/pci.h> #include <linux/slab.h> #include <linux/mbus.h> +#include <video/vga.h> #include <asm/irq.h> #include <asm/mach/pci.h> #include <plat/pcie.h> diff --git a/arch/arm/mach-prima2/clock.c b/arch/arm/mach-prima2/clock.c index f9a2aaf63f7..615a4e75cea 100644 --- a/arch/arm/mach-prima2/clock.c +++ b/arch/arm/mach-prima2/clock.c @@ -481,6 +481,7 @@ static void __init sirfsoc_clk_init(void) static struct of_device_id clkc_ids[] = { { .compatible = "sirf,prima2-clkc" }, + {}, }; void __init sirfsoc_of_clk_init(void) diff --git a/arch/arm/mach-prima2/irq.c b/arch/arm/mach-prima2/irq.c index c3404cbb6ff..7af254d046b 100644 --- a/arch/arm/mach-prima2/irq.c +++ b/arch/arm/mach-prima2/irq.c @@ -51,6 +51,7 @@ static __init void sirfsoc_irq_init(void) static struct of_device_id intc_ids[] = { { .compatible = "sirf,prima2-intc" }, + {}, }; void __init sirfsoc_of_irq_init(void) diff --git a/arch/arm/mach-prima2/rstc.c b/arch/arm/mach-prima2/rstc.c index d074786e83d..492cfa8d261 100644 --- a/arch/arm/mach-prima2/rstc.c +++ b/arch/arm/mach-prima2/rstc.c @@ -19,6 +19,7 @@ static DEFINE_MUTEX(rstc_lock); static struct of_device_id rstc_ids[] = { { .compatible = "sirf,prima2-rstc" }, + {}, }; static int __init sirfsoc_of_rstc_init(void) diff --git a/arch/arm/mach-prima2/timer.c b/arch/arm/mach-prima2/timer.c index 44027f34a88..ed7ec48d11d 100644 --- a/arch/arm/mach-prima2/timer.c +++ b/arch/arm/mach-prima2/timer.c @@ -190,6 +190,7 @@ static void __init sirfsoc_timer_init(void) static struct of_device_id timer_ids[] = { { .compatible = "sirf,prima2-tick" }, + {}, }; static void __init sirfsoc_of_timer_map(void) diff --git a/arch/arm/mach-realview/include/mach/system.h b/arch/arm/mach-realview/include/mach/system.h index a30f2e3ec17..6657ff23116 100644 --- a/arch/arm/mach-realview/include/mach/system.h +++ b/arch/arm/mach-realview/include/mach/system.h @@ -44,6 +44,7 @@ static inline void arch_reset(char mode, const char *cmd) */ if (realview_reset) realview_reset(mode); + dsb(); } #endif diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c index a1a7176675b..38058af4897 100644 --- a/arch/arm/mach-s3c2443/clock.c +++ b/arch/arm/mach-s3c2443/clock.c @@ -128,7 +128,7 @@ static int s3c2443_armclk_setrate(struct clk *clk, unsigned long rate) unsigned long clkcon0; clkcon0 = __raw_readl(S3C2443_CLKDIV0); - clkcon0 &= S3C2443_CLKDIV0_ARMDIV_MASK; + clkcon0 &= ~S3C2443_CLKDIV0_ARMDIV_MASK; clkcon0 |= val << S3C2443_CLKDIV0_ARMDIV_SHIFT; __raw_writel(clkcon0, S3C2443_CLKDIV0); } diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c index 9026249233a..af0c2fe1ea3 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410.c @@ -65,7 +65,7 @@ #include <plat/iic.h> #include <plat/pm.h> -#include <sound/wm8915.h> +#include <sound/wm8996.h> #include <sound/wm8962.h> #include <sound/wm9081.h> @@ -614,7 +614,7 @@ static struct wm831x_pdata glenfarclas_pmic_pdata __initdata = { .disable_touch = true, }; -static struct wm8915_retune_mobile_config wm8915_retune[] = { +static struct wm8996_retune_mobile_config wm8996_retune[] = { { .name = "Sub LPF", .rate = 48000, @@ -635,12 +635,12 @@ static struct wm8915_retune_mobile_config wm8915_retune[] = { }, }; -static struct wm8915_pdata wm8915_pdata __initdata = { +static struct wm8996_pdata wm8996_pdata __initdata = { .ldo_ena = S3C64XX_GPN(7), .gpio_base = CODEC_GPIO_BASE, .micdet_def = 1, - .inl_mode = WM8915_DIFFERRENTIAL_1, - .inr_mode = WM8915_DIFFERRENTIAL_1, + .inl_mode = WM8996_DIFFERRENTIAL_1, + .inr_mode = WM8996_DIFFERRENTIAL_1, .irq_flags = IRQF_TRIGGER_RISING, @@ -652,8 +652,8 @@ static struct wm8915_pdata wm8915_pdata __initdata = { 0x020e, /* GPIO5 == CLKOUT */ }, - .retune_mobile_cfgs = wm8915_retune, - .num_retune_mobile_cfgs = ARRAY_SIZE(wm8915_retune), + .retune_mobile_cfgs = wm8996_retune, + .num_retune_mobile_cfgs = ARRAY_SIZE(wm8996_retune), }; static struct wm8962_pdata wm8962_pdata __initdata = { @@ -679,8 +679,8 @@ static struct i2c_board_info i2c_devs1[] __initdata = { .platform_data = &glenfarclas_pmic_pdata }, { I2C_BOARD_INFO("wm1250-ev1", 0x27) }, - { I2C_BOARD_INFO("wm8915", 0x1a), - .platform_data = &wm8915_pdata, + { I2C_BOARD_INFO("wm8996", 0x1a), + .platform_data = &wm8996_pdata, .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2, }, { I2C_BOARD_INFO("wm9081", 0x6c), diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c index ecbea92bf83..a9f3183e029 100644 --- a/arch/arm/mach-s3c64xx/mach-smdk6410.c +++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c @@ -262,45 +262,6 @@ static struct samsung_keypad_platdata smdk6410_keypad_data __initdata = { .cols = 8, }; -static int smdk6410_backlight_init(struct device *dev) -{ - int ret; - - ret = gpio_request(S3C64XX_GPF(15), "Backlight"); - if (ret) { - printk(KERN_ERR "failed to request GPF for PWM-OUT1\n"); - return ret; - } - - /* Configure GPIO pin with S3C64XX_GPF15_PWM_TOUT1 */ - s3c_gpio_cfgpin(S3C64XX_GPF(15), S3C_GPIO_SFN(2)); - - return 0; -} - -static void smdk6410_backlight_exit(struct device *dev) -{ - s3c_gpio_cfgpin(S3C64XX_GPF(15), S3C_GPIO_OUTPUT); - gpio_free(S3C64XX_GPF(15)); -} - -static struct platform_pwm_backlight_data smdk6410_backlight_data = { - .pwm_id = 1, - .max_brightness = 255, - .dft_brightness = 255, - .pwm_period_ns = 78770, - .init = smdk6410_backlight_init, - .exit = smdk6410_backlight_exit, -}; - -static struct platform_device smdk6410_backlight_device = { - .name = "pwm-backlight", - .dev = { - .parent = &s3c_device_timer[1].dev, - .platform_data = &smdk6410_backlight_data, - }, -}; - static struct map_desc smdk6410_iodesc[] = {}; static struct platform_device *smdk6410_devices[] __initdata = { diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c64xx/pm.c index 8bad6437068..055e2858b0d 100644 --- a/arch/arm/mach-s3c64xx/pm.c +++ b/arch/arm/mach-s3c64xx/pm.c @@ -16,6 +16,7 @@ #include <linux/suspend.h> #include <linux/serial_core.h> #include <linux/io.h> +#include <linux/gpio.h> #include <mach/map.h> #include <mach/irqs.h> diff --git a/arch/arm/mach-s5p64x0/irq-eint.c b/arch/arm/mach-s5p64x0/irq-eint.c index 69ed4545112..fe7380f5c3c 100644 --- a/arch/arm/mach-s5p64x0/irq-eint.c +++ b/arch/arm/mach-s5p64x0/irq-eint.c @@ -129,7 +129,7 @@ static int s5p64x0_alloc_gc(void) } ct = gc->chip_types; - ct->chip.irq_ack = irq_gc_ack; + ct->chip.irq_ack = irq_gc_ack_set_bit; ct->chip.irq_mask = irq_gc_mask_set_bit; ct->chip.irq_unmask = irq_gc_mask_clr_bit; ct->chip.irq_set_type = s5p64x0_irq_eint_set_type; diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c index 52a8e607bcc..f5f8fa89679 100644 --- a/arch/arm/mach-s5pv210/clock.c +++ b/arch/arm/mach-s5pv210/clock.c @@ -815,8 +815,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLK_DIV3, .shift = 20, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "s5pv210-fimc.0", + .name = "sclk_cam0", .enable = s5pv210_clk_mask0_ctrl, .ctrlbit = (1 << 3), }, @@ -825,8 +824,7 @@ static struct clksrc_clk clksrcs[] = { .reg_div = { .reg = S5P_CLK_DIV1, .shift = 12, .size = 4 }, }, { .clk = { - .name = "sclk_cam", - .devname = "s5pv210-fimc.1", + .name = "sclk_cam1", .enable = s5pv210_clk_mask0_ctrl, .ctrlbit = (1 << 4), }, diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c index 309e388a8a8..f149d278377 100644 --- a/arch/arm/mach-s5pv210/pm.c +++ b/arch/arm/mach-s5pv210/pm.c @@ -88,7 +88,7 @@ static struct sleep_save s5pv210_core_save[] = { SAVE_ITEM(S3C2410_TCNTO(0)), }; -void s5pv210_cpu_suspend(unsigned long arg) +static int s5pv210_cpu_suspend(unsigned long arg) { unsigned long tmp; diff --git a/arch/arm/mach-sa1100/pci-nanoengine.c b/arch/arm/mach-sa1100/pci-nanoengine.c index 964c6c3cd7a..dd39fee5954 100644 --- a/arch/arm/mach-sa1100/pci-nanoengine.c +++ b/arch/arm/mach-sa1100/pci-nanoengine.c @@ -28,6 +28,7 @@ #include <asm/mach-types.h> #include <mach/nanoengine.h> +#include <mach/hardware.h> static DEFINE_SPINLOCK(nano_lock); diff --git a/arch/arm/mach-shmobile/board-ag5evm.c b/arch/arm/mach-shmobile/board-ag5evm.c index ce5c2513c6c..cdfdd624d21 100644 --- a/arch/arm/mach-shmobile/board-ag5evm.c +++ b/arch/arm/mach-shmobile/board-ag5evm.c @@ -341,6 +341,7 @@ static struct platform_device mipidsi0_device = { static struct sh_mobile_sdhi_info sdhi0_info = { .dma_slave_tx = SHDMA_SLAVE_SDHI0_TX, .dma_slave_rx = SHDMA_SLAVE_SDHI0_RX, + .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT, .tmio_caps = MMC_CAP_SD_HIGHSPEED, .tmio_ocr_mask = MMC_VDD_27_28 | MMC_VDD_28_29, }; @@ -382,7 +383,7 @@ void ag5evm_sdhi1_set_pwr(struct platform_device *pdev, int state) } static struct sh_mobile_sdhi_info sh_sdhi1_info = { - .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE, + .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT, .tmio_caps = MMC_CAP_NONREMOVABLE | MMC_CAP_SDIO_IRQ, .tmio_ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, .set_pwr = ag5evm_sdhi1_set_pwr, diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c index 9e0856b2f9e..523f608eb8c 100644 --- a/arch/arm/mach-shmobile/board-ap4evb.c +++ b/arch/arm/mach-shmobile/board-ap4evb.c @@ -1412,6 +1412,7 @@ static void __init ap4evb_init(void) fsi_init_pm_clock(); sh7372_pm_init(); pm_clk_add(&fsi_device.dev, "spu2"); + pm_clk_add(&lcdc1_device.dev, "hdmi"); } static void __init ap4evb_timer_init(void) diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c index d41c01f83f1..17c19dc2560 100644 --- a/arch/arm/mach-shmobile/board-mackerel.c +++ b/arch/arm/mach-shmobile/board-mackerel.c @@ -641,6 +641,8 @@ static struct usbhs_private usbhs0_private = { }, .driver_param = { .buswait_bwait = 4, + .d0_tx_id = SHDMA_SLAVE_USB0_TX, + .d1_rx_id = SHDMA_SLAVE_USB0_RX, }, }, }; @@ -810,6 +812,8 @@ static struct usbhs_private usbhs1_private = { .buswait_bwait = 4, .pipe_type = usbhs1_pipe_cfg, .pipe_size = ARRAY_SIZE(usbhs1_pipe_cfg), + .d0_tx_id = SHDMA_SLAVE_USB1_TX, + .d1_rx_id = SHDMA_SLAVE_USB1_RX, }, }, }; @@ -1588,6 +1592,7 @@ static void __init mackerel_init(void) hdmi_init_pm_clock(); sh7372_pm_init(); pm_clk_add(&fsi_device.dev, "spu2"); + pm_clk_add(&hdmi_lcdc_device.dev, "hdmi"); } static void __init mackerel_timer_init(void) diff --git a/arch/arm/mach-shmobile/clock-sh7372.c b/arch/arm/mach-shmobile/clock-sh7372.c index 6b1619a65db..66975921e64 100644 --- a/arch/arm/mach-shmobile/clock-sh7372.c +++ b/arch/arm/mach-shmobile/clock-sh7372.c @@ -503,16 +503,17 @@ static struct clk *late_main_clks[] = { &sh7372_fsidivb_clk, }; -enum { MSTP001, +enum { MSTP001, MSTP000, MSTP131, MSTP130, MSTP129, MSTP128, MSTP127, MSTP126, MSTP125, MSTP118, MSTP117, MSTP116, MSTP113, MSTP106, MSTP101, MSTP100, MSTP223, - MSTP218, MSTP217, MSTP216, - MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200, - MSTP329, MSTP328, MSTP323, MSTP322, MSTP314, MSTP313, MSTP312, - MSTP423, MSTP415, MSTP413, MSTP411, MSTP410, MSTP406, MSTP403, + MSTP218, MSTP217, MSTP216, MSTP214, MSTP208, MSTP207, + MSTP206, MSTP205, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200, + MSTP328, MSTP323, MSTP322, MSTP314, MSTP313, MSTP312, + MSTP423, MSTP415, MSTP413, MSTP411, MSTP410, MSTP407, MSTP406, + MSTP405, MSTP404, MSTP403, MSTP400, MSTP_NR }; #define MSTP(_parent, _reg, _bit, _flags) \ @@ -520,6 +521,7 @@ enum { MSTP001, static struct clk mstp_clks[MSTP_NR] = { [MSTP001] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR0, 1, 0), /* IIC2 */ + [MSTP000] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR0, 0, 0), /* MSIOF0 */ [MSTP131] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 31, 0), /* VEU3 */ [MSTP130] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 30, 0), /* VEU2 */ [MSTP129] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 29, 0), /* VEU1 */ @@ -538,14 +540,16 @@ static struct clk mstp_clks[MSTP_NR] = { [MSTP218] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* DMAC1 */ [MSTP217] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* DMAC2 */ [MSTP216] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 16, 0), /* DMAC3 */ + [MSTP214] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 14, 0), /* USBDMAC */ + [MSTP208] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 8, 0), /* MSIOF1 */ [MSTP207] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */ [MSTP206] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */ + [MSTP205] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 5, 0), /* MSIOF2 */ [MSTP204] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */ [MSTP203] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */ [MSTP202] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */ [MSTP201] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */ [MSTP200] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */ - [MSTP329] = MSTP(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */ [MSTP328] = MSTP(&div6_clks[DIV6_SPU], SMSTPCR3, 28, 0), /* FSI2 */ [MSTP323] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 23, 0), /* IIC1 */ [MSTP322] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 22, 0), /* USB0 */ @@ -557,8 +561,12 @@ static struct clk mstp_clks[MSTP_NR] = { [MSTP413] = MSTP(&pllc1_div2_clk, SMSTPCR4, 13, 0), /* HDMI */ [MSTP411] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 11, 0), /* IIC3 */ [MSTP410] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 10, 0), /* IIC4 */ + [MSTP407] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 7, 0), /* USB-DMAC1 */ [MSTP406] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 6, 0), /* USB1 */ + [MSTP405] = MSTP(&r_clk, SMSTPCR4, 5, 0), /* CMT4 */ + [MSTP404] = MSTP(&r_clk, SMSTPCR4, 4, 0), /* CMT3 */ [MSTP403] = MSTP(&r_clk, SMSTPCR4, 3, 0), /* KEYSC */ + [MSTP400] = MSTP(&r_clk, SMSTPCR4, 0, 0), /* CMT2 */ }; static struct clk_lookup lookups[] = { @@ -609,6 +617,7 @@ static struct clk_lookup lookups[] = { /* MSTP32 clocks */ CLKDEV_DEV_ID("i2c-sh_mobile.2", &mstp_clks[MSTP001]), /* IIC2 */ + CLKDEV_DEV_ID("spi_sh_msiof.0", &mstp_clks[MSTP000]), /* MSIOF0 */ CLKDEV_DEV_ID("uio_pdrv_genirq.4", &mstp_clks[MSTP131]), /* VEU3 */ CLKDEV_DEV_ID("uio_pdrv_genirq.3", &mstp_clks[MSTP130]), /* VEU2 */ CLKDEV_DEV_ID("uio_pdrv_genirq.2", &mstp_clks[MSTP129]), /* VEU1 */ @@ -629,14 +638,16 @@ static struct clk_lookup lookups[] = { CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]), /* DMAC1 */ CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]), /* DMAC2 */ CLKDEV_DEV_ID("sh-dma-engine.2", &mstp_clks[MSTP216]), /* DMAC3 */ + CLKDEV_DEV_ID("sh-dma-engine.3", &mstp_clks[MSTP214]), /* USB-DMAC0 */ + CLKDEV_DEV_ID("spi_sh_msiof.1", &mstp_clks[MSTP208]), /* MSIOF1 */ CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */ CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP206]), /* SCIFB */ + CLKDEV_DEV_ID("spi_sh_msiof.2", &mstp_clks[MSTP205]), /* MSIOF2 */ CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */ CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */ CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]), /* SCIFA2 */ CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]), /* SCIFA3 */ CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]), /* SCIFA4 */ - CLKDEV_DEV_ID("sh_cmt.10", &mstp_clks[MSTP329]), /* CMT10 */ CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]), /* FSI2 */ CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]), /* IIC1 */ CLKDEV_DEV_ID("r8a66597_hcd.0", &mstp_clks[MSTP322]), /* USB0 */ @@ -650,11 +661,17 @@ static struct clk_lookup lookups[] = { CLKDEV_DEV_ID("sh-mobile-hdmi", &mstp_clks[MSTP413]), /* HDMI */ CLKDEV_DEV_ID("i2c-sh_mobile.3", &mstp_clks[MSTP411]), /* IIC3 */ CLKDEV_DEV_ID("i2c-sh_mobile.4", &mstp_clks[MSTP410]), /* IIC4 */ + CLKDEV_DEV_ID("sh-dma-engine.4", &mstp_clks[MSTP407]), /* USB-DMAC1 */ CLKDEV_DEV_ID("r8a66597_hcd.1", &mstp_clks[MSTP406]), /* USB1 */ CLKDEV_DEV_ID("r8a66597_udc.1", &mstp_clks[MSTP406]), /* USB1 */ CLKDEV_DEV_ID("renesas_usbhs.1", &mstp_clks[MSTP406]), /* USB1 */ + CLKDEV_DEV_ID("sh_cmt.4", &mstp_clks[MSTP405]), /* CMT4 */ + CLKDEV_DEV_ID("sh_cmt.3", &mstp_clks[MSTP404]), /* CMT3 */ CLKDEV_DEV_ID("sh_keysc.0", &mstp_clks[MSTP403]), /* KEYSC */ + CLKDEV_DEV_ID("sh_cmt.2", &mstp_clks[MSTP400]), /* CMT2 */ + CLKDEV_ICK_ID("hdmi", "sh_mobile_lcdc_fb.1", + &div6_reparent_clks[DIV6_HDMI]), CLKDEV_ICK_ID("ick", "sh-mobile-hdmi", &div6_reparent_clks[DIV6_HDMI]), CLKDEV_ICK_ID("icka", "sh_fsi2", &div6_reparent_clks[DIV6_FSIA]), CLKDEV_ICK_ID("ickb", "sh_fsi2", &div6_reparent_clks[DIV6_FSIB]), diff --git a/arch/arm/mach-shmobile/clock-sh73a0.c b/arch/arm/mach-shmobile/clock-sh73a0.c index 6db2ccabc2b..61a846bb30f 100644 --- a/arch/arm/mach-shmobile/clock-sh73a0.c +++ b/arch/arm/mach-shmobile/clock-sh73a0.c @@ -365,7 +365,7 @@ void __init sh73a0_clock_init(void) __raw_writel(0x108, SD2CKCR); /* detect main clock parent */ - switch ((__raw_readl(CKSCR) >> 24) & 0x03) { + switch ((__raw_readl(CKSCR) >> 28) & 0x03) { case 0: main_clk.parent = &sh73a0_extal1_clk; break; diff --git a/arch/arm/mach-shmobile/include/mach/sh7372.h b/arch/arm/mach-shmobile/include/mach/sh7372.h index ce595cee86c..24e63a85e66 100644 --- a/arch/arm/mach-shmobile/include/mach/sh7372.h +++ b/arch/arm/mach-shmobile/include/mach/sh7372.h @@ -459,6 +459,10 @@ enum { SHDMA_SLAVE_SDHI2_TX, SHDMA_SLAVE_MMCIF_RX, SHDMA_SLAVE_MMCIF_TX, + SHDMA_SLAVE_USB0_TX, + SHDMA_SLAVE_USB0_RX, + SHDMA_SLAVE_USB1_TX, + SHDMA_SLAVE_USB1_RX, }; extern struct clk sh7372_extal1_clk; diff --git a/arch/arm/mach-shmobile/intc-sh7372.c b/arch/arm/mach-shmobile/intc-sh7372.c index 3b28743c77e..739315e30eb 100644 --- a/arch/arm/mach-shmobile/intc-sh7372.c +++ b/arch/arm/mach-shmobile/intc-sh7372.c @@ -379,7 +379,7 @@ enum { /* BBIF2 */ VPU, TSIF1, - _3DG_SGX530, + /* 3DG */ _2DDMAC, IIC2_ALI2, IIC2_TACKI2, IIC2_WAITI2, IIC2_DTEI2, IPMMU_IPMMUR, IPMMU_IPMMUR2, @@ -436,7 +436,7 @@ static struct intc_vect intcs_vectors[] = { /* BBIF2 */ INTCS_VECT(VPU, 0x980), INTCS_VECT(TSIF1, 0x9a0), - INTCS_VECT(_3DG_SGX530, 0x9e0), + /* 3DG */ INTCS_VECT(_2DDMAC, 0xa00), INTCS_VECT(IIC2_ALI2, 0xa80), INTCS_VECT(IIC2_TACKI2, 0xaa0), INTCS_VECT(IIC2_WAITI2, 0xac0), INTCS_VECT(IIC2_DTEI2, 0xae0), @@ -521,7 +521,7 @@ static struct intc_mask_reg intcs_mask_registers[] = { RTDMAC_1_DEI3, RTDMAC_1_DEI2, RTDMAC_1_DEI1, RTDMAC_1_DEI0 } }, { 0xffd20198, 0xffd201d8, 8, /* IMR6SA / IMCR6SA */ { 0, 0, MSIOF, 0, - _3DG_SGX530, 0, 0, 0 } }, + 0, 0, 0, 0 } }, { 0xffd2019c, 0xffd201dc, 8, /* IMR7SA / IMCR7SA */ { 0, TMU_TUNI2, TMU_TUNI1, TMU_TUNI0, 0, 0, 0, 0 } }, @@ -561,7 +561,6 @@ static struct intc_prio_reg intcs_prio_registers[] = { TMU_TUNI2, TSIF1 } }, { 0xffd2001c, 0, 16, 4, /* IPRHS */ { 0, 0, VEU, BEU } }, { 0xffd20020, 0, 16, 4, /* IPRIS */ { 0, MSIOF, TSIF0, IIC0 } }, - { 0xffd20024, 0, 16, 4, /* IPRJS */ { 0, _3DG_SGX530, 0, 0 } }, { 0xffd20028, 0, 16, 4, /* IPRKS */ { 0, 0, LMB, 0 } }, { 0xffd2002c, 0, 16, 4, /* IPRLS */ { IPMMU, 0, 0, 0 } }, { 0xffd20030, 0, 16, 4, /* IPRMS */ { IIC2, 0, 0, 0 } }, diff --git a/arch/arm/mach-shmobile/setup-sh7372.c b/arch/arm/mach-shmobile/setup-sh7372.c index 79f0413d872..2d9b1b1a253 100644 --- a/arch/arm/mach-shmobile/setup-sh7372.c +++ b/arch/arm/mach-shmobile/setup-sh7372.c @@ -169,35 +169,35 @@ static struct platform_device scif6_device = { }; /* CMT */ -static struct sh_timer_config cmt10_platform_data = { - .name = "CMT10", - .channel_offset = 0x10, - .timer_bit = 0, +static struct sh_timer_config cmt2_platform_data = { + .name = "CMT2", + .channel_offset = 0x40, + .timer_bit = 5, .clockevent_rating = 125, .clocksource_rating = 125, }; -static struct resource cmt10_resources[] = { +static struct resource cmt2_resources[] = { [0] = { - .name = "CMT10", - .start = 0xe6138010, - .end = 0xe613801b, + .name = "CMT2", + .start = 0xe6130040, + .end = 0xe613004b, .flags = IORESOURCE_MEM, }, [1] = { - .start = evt2irq(0x0b00), /* CMT1_CMT10 */ + .start = evt2irq(0x0b80), /* CMT2 */ .flags = IORESOURCE_IRQ, }, }; -static struct platform_device cmt10_device = { +static struct platform_device cmt2_device = { .name = "sh_cmt", - .id = 10, + .id = 2, .dev = { - .platform_data = &cmt10_platform_data, + .platform_data = &cmt2_platform_data, }, - .resource = cmt10_resources, - .num_resources = ARRAY_SIZE(cmt10_resources), + .resource = cmt2_resources, + .num_resources = ARRAY_SIZE(cmt2_resources), }; /* TMU */ @@ -602,6 +602,150 @@ static struct platform_device dma2_device = { }, }; +/* + * USB-DMAC + */ + +unsigned int usbts_shift[] = {3, 4, 5}; + +enum { + XMIT_SZ_8BYTE = 0, + XMIT_SZ_16BYTE = 1, + XMIT_SZ_32BYTE = 2, +}; + +#define USBTS_INDEX2VAL(i) (((i) & 3) << 6) + +static const struct sh_dmae_channel sh7372_usb_dmae_channels[] = { + { + .offset = 0, + }, { + .offset = 0x20, + }, +}; + +/* USB DMAC0 */ +static const struct sh_dmae_slave_config sh7372_usb_dmae0_slaves[] = { + { + .slave_id = SHDMA_SLAVE_USB0_TX, + .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE), + }, { + .slave_id = SHDMA_SLAVE_USB0_RX, + .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE), + }, +}; + +static struct sh_dmae_pdata usb_dma0_platform_data = { + .slave = sh7372_usb_dmae0_slaves, + .slave_num = ARRAY_SIZE(sh7372_usb_dmae0_slaves), + .channel = sh7372_usb_dmae_channels, + .channel_num = ARRAY_SIZE(sh7372_usb_dmae_channels), + .ts_low_shift = 6, + .ts_low_mask = 0xc0, + .ts_high_shift = 0, + .ts_high_mask = 0, + .ts_shift = usbts_shift, + .ts_shift_num = ARRAY_SIZE(usbts_shift), + .dmaor_init = DMAOR_DME, + .chcr_offset = 0x14, + .chcr_ie_bit = 1 << 5, + .dmaor_is_32bit = 1, + .needs_tend_set = 1, + .no_dmars = 1, +}; + +static struct resource sh7372_usb_dmae0_resources[] = { + { + /* Channel registers and DMAOR */ + .start = 0xe68a0020, + .end = 0xe68a0064 - 1, + .flags = IORESOURCE_MEM, + }, + { + /* VCR/SWR/DMICR */ + .start = 0xe68a0000, + .end = 0xe68a0014 - 1, + .flags = IORESOURCE_MEM, + }, + { + /* IRQ for channels */ + .start = evt2irq(0x0a00), + .end = evt2irq(0x0a00), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device usb_dma0_device = { + .name = "sh-dma-engine", + .id = 3, + .resource = sh7372_usb_dmae0_resources, + .num_resources = ARRAY_SIZE(sh7372_usb_dmae0_resources), + .dev = { + .platform_data = &usb_dma0_platform_data, + }, +}; + +/* USB DMAC1 */ +static const struct sh_dmae_slave_config sh7372_usb_dmae1_slaves[] = { + { + .slave_id = SHDMA_SLAVE_USB1_TX, + .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE), + }, { + .slave_id = SHDMA_SLAVE_USB1_RX, + .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE), + }, +}; + +static struct sh_dmae_pdata usb_dma1_platform_data = { + .slave = sh7372_usb_dmae1_slaves, + .slave_num = ARRAY_SIZE(sh7372_usb_dmae1_slaves), + .channel = sh7372_usb_dmae_channels, + .channel_num = ARRAY_SIZE(sh7372_usb_dmae_channels), + .ts_low_shift = 6, + .ts_low_mask = 0xc0, + .ts_high_shift = 0, + .ts_high_mask = 0, + .ts_shift = usbts_shift, + .ts_shift_num = ARRAY_SIZE(usbts_shift), + .dmaor_init = DMAOR_DME, + .chcr_offset = 0x14, + .chcr_ie_bit = 1 << 5, + .dmaor_is_32bit = 1, + .needs_tend_set = 1, + .no_dmars = 1, +}; + +static struct resource sh7372_usb_dmae1_resources[] = { + { + /* Channel registers and DMAOR */ + .start = 0xe68c0020, + .end = 0xe68c0064 - 1, + .flags = IORESOURCE_MEM, + }, + { + /* VCR/SWR/DMICR */ + .start = 0xe68c0000, + .end = 0xe68c0014 - 1, + .flags = IORESOURCE_MEM, + }, + { + /* IRQ for channels */ + .start = evt2irq(0x1d00), + .end = evt2irq(0x1d00), + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device usb_dma1_device = { + .name = "sh-dma-engine", + .id = 4, + .resource = sh7372_usb_dmae1_resources, + .num_resources = ARRAY_SIZE(sh7372_usb_dmae1_resources), + .dev = { + .platform_data = &usb_dma1_platform_data, + }, +}; + /* VPU */ static struct uio_info vpu_platform_data = { .name = "VPU5HG", @@ -818,7 +962,7 @@ static struct platform_device *sh7372_early_devices[] __initdata = { &scif4_device, &scif5_device, &scif6_device, - &cmt10_device, + &cmt2_device, &tmu00_device, &tmu01_device, }; @@ -829,6 +973,8 @@ static struct platform_device *sh7372_late_devices[] __initdata = { &dma0_device, &dma1_device, &dma2_device, + &usb_dma0_device, + &usb_dma1_device, &vpu_device, &veu0_device, &veu1_device, diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c index 9e6b93b1a04..d0d267a8d3f 100644 --- a/arch/arm/mach-vexpress/v2m.c +++ b/arch/arm/mach-vexpress/v2m.c @@ -318,6 +318,10 @@ static struct clk v2m_sp804_clk = { .rate = 1000000, }; +static struct clk v2m_ref_clk = { + .rate = 32768, +}; + static struct clk dummy_apb_pclk; static struct clk_lookup v2m_lookups[] = { @@ -348,6 +352,9 @@ static struct clk_lookup v2m_lookups[] = { }, { /* CLCD */ .dev_id = "mb:clcd", .clk = &osc1_clk, + }, { /* SP805 WDT */ + .dev_id = "mb:wdt", + .clk = &v2m_ref_clk, }, { /* SP804 timers */ .dev_id = "sp804", .con_id = "v2m-timer0", diff --git a/arch/arm/mm/abort-macro.S b/arch/arm/mm/abort-macro.S index 52162d59407..2cbf68ef0e8 100644 --- a/arch/arm/mm/abort-macro.S +++ b/arch/arm/mm/abort-macro.S @@ -17,7 +17,7 @@ cmp \tmp, # 0x5600 @ Is it ldrsb? orreq \tmp, \tmp, #1 << 11 @ Set L-bit if yes tst \tmp, #1 << 11 @ L = 0 -> write - orreq \psr, \psr, #1 << 11 @ yes. + orreq \fsr, \fsr, #1 << 11 @ yes. b do_DataAbort not_thumb: .endm diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c index be7c638b648..cfbcf8b9559 100644 --- a/arch/arm/mm/alignment.c +++ b/arch/arm/mm/alignment.c @@ -22,6 +22,7 @@ #include <linux/sched.h> #include <linux/uaccess.h> +#include <asm/system.h> #include <asm/unaligned.h> #include "fault.h" @@ -95,6 +96,33 @@ static const char *usermode_action[] = { "signal+warn" }; +/* Return true if and only if the ARMv6 unaligned access model is in use. */ +static bool cpu_is_v6_unaligned(void) +{ + return cpu_architecture() >= CPU_ARCH_ARMv6 && (cr_alignment & CR_U); +} + +static int safe_usermode(int new_usermode, bool warn) +{ + /* + * ARMv6 and later CPUs can perform unaligned accesses for + * most single load and store instructions up to word size. + * LDM, STM, LDRD and STRD still need to be handled. + * + * Ignoring the alignment fault is not an option on these + * CPUs since we spin re-faulting the instruction without + * making any progress. + */ + if (cpu_is_v6_unaligned() && !(new_usermode & (UM_FIXUP | UM_SIGNAL))) { + new_usermode |= UM_FIXUP; + + if (warn) + printk(KERN_WARNING "alignment: ignoring faults is unsafe on this CPU. Defaulting to fixup mode.\n"); + } + + return new_usermode; +} + static int alignment_proc_show(struct seq_file *m, void *v) { seq_printf(m, "User:\t\t%lu\n", ai_user); @@ -125,7 +153,7 @@ static ssize_t alignment_proc_write(struct file *file, const char __user *buffer if (get_user(mode, buffer)) return -EFAULT; if (mode >= '0' && mode <= '5') - ai_usermode = mode - '0'; + ai_usermode = safe_usermode(mode - '0', true); } return count; } @@ -886,9 +914,16 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs) if (ai_usermode & UM_FIXUP) goto fixup; - if (ai_usermode & UM_SIGNAL) - force_sig(SIGBUS, current); - else { + if (ai_usermode & UM_SIGNAL) { + siginfo_t si; + + si.si_signo = SIGBUS; + si.si_errno = 0; + si.si_code = BUS_ADRALN; + si.si_addr = (void __user *)addr; + + force_sig_info(si.si_signo, &si, current); + } else { /* * We're about to disable the alignment trap and return to * user space. But if an interrupt occurs before actually @@ -926,20 +961,11 @@ static int __init alignment_init(void) return -ENOMEM; #endif - /* - * ARMv6 and later CPUs can perform unaligned accesses for - * most single load and store instructions up to word size. - * LDM, STM, LDRD and STRD still need to be handled. - * - * Ignoring the alignment fault is not an option on these - * CPUs since we spin re-faulting the instruction without - * making any progress. - */ - if (cpu_architecture() >= CPU_ARCH_ARMv6 && (cr_alignment & CR_U)) { + if (cpu_is_v6_unaligned()) { cr_alignment &= ~CR_A; cr_no_alignment &= ~CR_A; set_cr(cr_alignment); - ai_usermode = UM_FIXUP; + ai_usermode = safe_usermode(ai_usermode, false); } hook_fault_code(1, do_alignment, SIGBUS, BUS_ADRALN, diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c index 44c086710d2..9ecfdb51195 100644 --- a/arch/arm/mm/cache-l2x0.c +++ b/arch/arm/mm/cache-l2x0.c @@ -277,6 +277,25 @@ static void l2x0_disable(void) spin_unlock_irqrestore(&l2x0_lock, flags); } +static void __init l2x0_unlock(__u32 cache_id) +{ + int lockregs; + int i; + + if (cache_id == L2X0_CACHE_ID_PART_L310) + lockregs = 8; + else + /* L210 and unknown types */ + lockregs = 1; + + for (i = 0; i < lockregs; i++) { + writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE + + i * L2X0_LOCKDOWN_STRIDE); + writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE + + i * L2X0_LOCKDOWN_STRIDE); + } +} + void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask) { __u32 aux; @@ -328,6 +347,8 @@ void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask) * accessing the below registers will fault. */ if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) { + /* Make sure that I&D is not locked down when starting */ + l2x0_unlock(cache_id); /* l2x0 controller is disabled */ writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL); diff --git a/arch/arm/mm/cache-v7.S b/arch/arm/mm/cache-v7.S index 3b24bfa3b82..07c4bc8ea0a 100644 --- a/arch/arm/mm/cache-v7.S +++ b/arch/arm/mm/cache-v7.S @@ -174,6 +174,10 @@ ENTRY(v7_coherent_user_range) dcache_line_size r2, r3 sub r3, r2, #1 bic r12, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: USER( mcr p15, 0, r12, c7, c11, 1 ) @ clean D line to the point of unification add r12, r12, r2 @@ -223,6 +227,10 @@ ENTRY(v7_flush_kern_dcache_area) add r1, r0, r1 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D line / unified line add r0, r0, r2 @@ -247,6 +255,10 @@ v7_dma_inv_range: sub r3, r2, #1 tst r0, r3 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif mcrne p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line tst r1, r3 @@ -270,6 +282,10 @@ v7_dma_clean_range: dcache_line_size r2, r3 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c10, 1 @ clean D / U line add r0, r0, r2 @@ -288,6 +304,10 @@ ENTRY(v7_dma_flush_range) dcache_line_size r2, r3 sub r3, r2, #1 bic r0, r0, r3 +#ifdef CONFIG_ARM_ERRATA_764369 + ALT_SMP(W(dsb)) + ALT_UP(W(nop)) +#endif 1: mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line add r0, r0, r2 diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index 0a0a1e7c20d..c3ff82f92d9 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -324,6 +324,8 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, if (addr) *handle = pfn_to_dma(dev, page_to_pfn(page)); + else + __dma_free_buffer(page, size); return addr; } diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c index 2fee782077c..cc7e2d8be9a 100644 --- a/arch/arm/mm/init.c +++ b/arch/arm/mm/init.c @@ -298,7 +298,7 @@ static void __init arm_bootmem_free(unsigned long min, unsigned long max_low, #ifdef CONFIG_HAVE_ARCH_PFN_VALID int pfn_valid(unsigned long pfn) { - return memblock_is_memory(pfn << PAGE_SHIFT); + return memblock_is_memory(__pfn_to_phys(pfn)); } EXPORT_SYMBOL(pfn_valid); #endif @@ -441,7 +441,7 @@ static inline int free_area(unsigned long pfn, unsigned long end, char *s) static inline void poison_init_mem(void *s, size_t count) { u32 *p = (u32 *)s; - while ((count = count - 4)) + for (; count != 0; count -= 4) *p++ = 0xe7fddef0; } diff --git a/arch/arm/mm/proc-arm920.S b/arch/arm/mm/proc-arm920.S index 92bd102e398..2e6849b41f6 100644 --- a/arch/arm/mm/proc-arm920.S +++ b/arch/arm/mm/proc-arm920.S @@ -379,7 +379,7 @@ ENTRY(cpu_arm920_set_pte_ext) /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */ .globl cpu_arm920_suspend_size -.equ cpu_arm920_suspend_size, 4 * 3 +.equ cpu_arm920_suspend_size, 4 * 4 #ifdef CONFIG_PM_SLEEP ENTRY(cpu_arm920_do_suspend) stmfd sp!, {r4 - r7, lr} diff --git a/arch/arm/mm/proc-arm926.S b/arch/arm/mm/proc-arm926.S index 2bbcf053dff..cd8f79c3a28 100644 --- a/arch/arm/mm/proc-arm926.S +++ b/arch/arm/mm/proc-arm926.S @@ -394,7 +394,7 @@ ENTRY(cpu_arm926_set_pte_ext) /* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */ .globl cpu_arm926_suspend_size -.equ cpu_arm926_suspend_size, 4 * 3 +.equ cpu_arm926_suspend_size, 4 * 4 #ifdef CONFIG_PM_SLEEP ENTRY(cpu_arm926_do_suspend) stmfd sp!, {r4 - r7, lr} diff --git a/arch/arm/mm/proc-arm946.S b/arch/arm/mm/proc-arm946.S index f8f7ea34bfc..683af3a182b 100644 --- a/arch/arm/mm/proc-arm946.S +++ b/arch/arm/mm/proc-arm946.S @@ -410,6 +410,7 @@ __arm946_proc_info: .long 0x41009460 .long 0xff00fff0 .long 0 + .long 0 b __arm946_setup .long cpu_arch_name .long cpu_elf_name @@ -418,6 +419,6 @@ __arm946_proc_info: .long arm946_processor_functions .long 0 .long 0 - .long arm940_cache_fns + .long arm946_cache_fns .size __arm946_proc_info, . - __arm946_proc_info diff --git a/arch/arm/mm/proc-sa1100.S b/arch/arm/mm/proc-sa1100.S index 07219c2ae11..69e7f2ef738 100644 --- a/arch/arm/mm/proc-sa1100.S +++ b/arch/arm/mm/proc-sa1100.S @@ -182,11 +182,11 @@ ENDPROC(cpu_sa1100_do_suspend) ENTRY(cpu_sa1100_do_resume) ldmia r0, {r4 - r7} @ load cp regs - mov r1, #0 - mcr p15, 0, r1, c8, c7, 0 @ flush I+D TLBs - mcr p15, 0, r1, c7, c7, 0 @ flush I&D cache - mcr p15, 0, r1, c9, c0, 0 @ invalidate RB - mcr p15, 0, r1, c9, c0, 5 @ allow user space to use RB + mov ip, #0 + mcr p15, 0, ip, c8, c7, 0 @ flush I+D TLBs + mcr p15, 0, ip, c7, c7, 0 @ flush I&D cache + mcr p15, 0, ip, c9, c0, 0 @ invalidate RB + mcr p15, 0, ip, c9, c0, 5 @ allow user space to use RB mcr p15, 0, r4, c3, c0, 0 @ domain ID mcr p15, 0, r5, c2, c0, 0 @ translation table base addr diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S index 219138d2f15..a923aa0fd00 100644 --- a/arch/arm/mm/proc-v6.S +++ b/arch/arm/mm/proc-v6.S @@ -223,6 +223,22 @@ __v6_setup: mrc p15, 0, r0, c1, c0, 0 @ read control register bic r0, r0, r5 @ clear bits them orr r0, r0, r6 @ set them +#ifdef CONFIG_ARM_ERRATA_364296 + /* + * Workaround for the 364296 ARM1136 r0p2 erratum (possible cache data + * corruption with hit-under-miss enabled). The conditional code below + * (setting the undocumented bit 31 in the auxiliary control register + * and the FI bit in the control register) disables hit-under-miss + * without putting the processor into full low interrupt latency mode. + */ + ldr r6, =0x4107b362 @ id for ARM1136 r0p2 + mrc p15, 0, r5, c0, c0, 0 @ get processor id + teq r5, r6 @ check for the faulty core + mrceq p15, 0, r5, c1, c0, 1 @ load aux control reg + orreq r5, r5, #(1 << 31) @ set the undocumented bit 31 + mcreq p15, 0, r5, c1, c0, 1 @ write aux control reg + orreq r0, r0, #(1 << 21) @ low interrupt latency configuration +#endif mov pc, lr @ return to head.S:__ret /* diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S index a30e78542cc..9049c0764db 100644 --- a/arch/arm/mm/proc-v7.S +++ b/arch/arm/mm/proc-v7.S @@ -66,6 +66,7 @@ ENDPROC(cpu_v7_proc_fin) ENTRY(cpu_v7_reset) mrc p15, 0, r1, c1, c0, 0 @ ctrl register bic r1, r1, #0x1 @ ...............m + THUMB( bic r1, r1, #1 << 30 ) @ SCTLR.TE (Thumb exceptions) mcr p15, 0, r1, c1, c0, 0 @ disable MMU isb mov pc, r0 @@ -247,13 +248,16 @@ ENTRY(cpu_v7_do_resume) mcr p15, 0, r7, c2, c0, 0 @ TTB 0 mcr p15, 0, r8, c2, c0, 1 @ TTB 1 mcr p15, 0, ip, c2, c0, 2 @ TTB control register - mcr p15, 0, r10, c1, c0, 1 @ Auxiliary control register + mrc p15, 0, r4, c1, c0, 1 @ Read Auxiliary control register + teq r4, r10 @ Is it already set? + mcrne p15, 0, r10, c1, c0, 1 @ No, so write it mcr p15, 0, r11, c1, c0, 2 @ Co-processor access control ldr r4, =PRRR @ PRRR ldr r5, =NMRR @ NMRR mcr p15, 0, r4, c10, c2, 0 @ write PRRR mcr p15, 0, r5, c10, c2, 1 @ write NMRR isb + dsb mov r0, r9 @ control register mov r2, r7, lsr #14 @ get TTB0 base mov r2, r2, lsl #14 diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S index 28c72a2006a..755e1bf2268 100644 --- a/arch/arm/mm/proc-xsc3.S +++ b/arch/arm/mm/proc-xsc3.S @@ -406,7 +406,7 @@ ENTRY(cpu_xsc3_set_pte_ext) .align .globl cpu_xsc3_suspend_size -.equ cpu_xsc3_suspend_size, 4 * 8 +.equ cpu_xsc3_suspend_size, 4 * 7 #ifdef CONFIG_PM_SLEEP ENTRY(cpu_xsc3_do_suspend) stmfd sp!, {r4 - r10, lr} @@ -418,12 +418,12 @@ ENTRY(cpu_xsc3_do_suspend) mrc p15, 0, r9, c1, c0, 1 @ auxiliary control reg mrc p15, 0, r10, c1, c0, 0 @ control reg bic r4, r4, #2 @ clear frequency change bit - stmia r0, {r1, r4 - r10} @ store v:p offset + cp regs + stmia r0, {r4 - r10} @ store cp regs ldmia sp!, {r4 - r10, pc} ENDPROC(cpu_xsc3_do_suspend) ENTRY(cpu_xsc3_do_resume) - ldmia r0, {r1, r4 - r10} @ load v:p offset + cp regs + ldmia r0, {r4 - r10} @ load cp regs mov ip, #0 mcr p15, 0, ip, c7, c7, 0 @ invalidate I & D caches, BTB mcr p15, 0, ip, c7, c10, 4 @ drain write (&fill) buffer diff --git a/arch/arm/plat-mxc/include/mach/debug-macro.S b/arch/arm/plat-mxc/include/mach/debug-macro.S index 91fc7cdb5dc..e4dde91f023 100644 --- a/arch/arm/plat-mxc/include/mach/debug-macro.S +++ b/arch/arm/plat-mxc/include/mach/debug-macro.S @@ -44,6 +44,14 @@ #define UART_PADDR MX51_UART1_BASE_ADDR #endif +/* iMX50/53 have same addresses, but not iMX51 */ +#if defined(CONFIG_SOC_IMX50) || defined(CONFIG_SOC_IMX53) +#ifdef UART_PADDR +#error "CONFIG_DEBUG_LL is incompatible with multiple archs" +#endif +#define UART_PADDR MX53_UART1_BASE_ADDR +#endif + #define UART_VADDR IMX_IO_ADDRESS(UART_PADDR) .macro addruart, rp, rv diff --git a/arch/arm/plat-mxc/include/mach/iomux-mx53.h b/arch/arm/plat-mxc/include/mach/iomux-mx53.h index 9440b9e00e8..5408fd1fc73 100644 --- a/arch/arm/plat-mxc/include/mach/iomux-mx53.h +++ b/arch/arm/plat-mxc/include/mach/iomux-mx53.h @@ -30,6 +30,9 @@ #define MX53_SDHC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_HIGH | \ PAD_CTL_SRE_FAST) +#define PAD_CTRL_I2C (PAD_CTL_SRE_FAST | PAD_CTL_ODE | PAD_CTL_PKE | \ + PAD_CTL_PUE | PAD_CTL_DSE_HIGH | PAD_CTL_PUS_100K_UP \ + | PAD_CTL_HYS) #define _MX53_PAD_GPIO_19__KPP_COL_5 IOMUX_PAD(0x348, 0x20, 0, 0x840, 0, 0) #define _MX53_PAD_GPIO_19__GPIO4_5 IOMUX_PAD(0x348, 0x20, 1, 0x0, 0, 0) @@ -1256,7 +1259,7 @@ #define MX53_PAD_KEY_COL3__GPIO4_12 (_MX53_PAD_KEY_COL3__GPIO4_12 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_COL3__USBOH3_H2_DP (_MX53_PAD_KEY_COL3__USBOH3_H2_DP | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_COL3__SPDIF_IN1 (_MX53_PAD_KEY_COL3__SPDIF_IN1 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_KEY_COL3__I2C2_SCL (_MX53_PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_KEY_COL3__I2C2_SCL (_MX53_PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_KEY_COL3__ECSPI1_SS3 (_MX53_PAD_KEY_COL3__ECSPI1_SS3 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_COL3__FEC_CRS (_MX53_PAD_KEY_COL3__FEC_CRS | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_COL3__USBPHY1_SIECLOCK (_MX53_PAD_KEY_COL3__USBPHY1_SIECLOCK | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1264,7 +1267,7 @@ #define MX53_PAD_KEY_ROW3__GPIO4_13 (_MX53_PAD_KEY_ROW3__GPIO4_13 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_ROW3__USBOH3_H2_DM (_MX53_PAD_KEY_ROW3__USBOH3_H2_DM | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_ROW3__CCM_ASRC_EXT_CLK (_MX53_PAD_KEY_ROW3__CCM_ASRC_EXT_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_KEY_ROW3__I2C2_SDA (_MX53_PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_KEY_ROW3__I2C2_SDA (_MX53_PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_KEY_ROW3__OSC32K_32K_OUT (_MX53_PAD_KEY_ROW3__OSC32K_32K_OUT | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_ROW3__CCM_PLL4_BYP (_MX53_PAD_KEY_ROW3__CCM_PLL4_BYP | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_KEY_ROW3__USBPHY1_LINESTATE_0 (_MX53_PAD_KEY_ROW3__USBPHY1_LINESTATE_0 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1536,7 +1539,7 @@ #define MX53_PAD_CSI0_DAT8__KPP_COL_7 (_MX53_PAD_CSI0_DAT8__KPP_COL_7 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT8__ECSPI2_SCLK (_MX53_PAD_CSI0_DAT8__ECSPI2_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC (_MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_CSI0_DAT8__I2C1_SDA (_MX53_PAD_CSI0_DAT8__I2C1_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_CSI0_DAT8__I2C1_SDA (_MX53_PAD_CSI0_DAT8__I2C1_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_CSI0_DAT8__EMI_EMI_DEBUG_37 (_MX53_PAD_CSI0_DAT8__EMI_EMI_DEBUG_37 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT8__TPIU_TRACE_5 (_MX53_PAD_CSI0_DAT8__TPIU_TRACE_5 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT9__IPU_CSI0_D_9 (_MX53_PAD_CSI0_DAT9__IPU_CSI0_D_9 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1544,7 +1547,7 @@ #define MX53_PAD_CSI0_DAT9__KPP_ROW_7 (_MX53_PAD_CSI0_DAT9__KPP_ROW_7 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT9__ECSPI2_MOSI (_MX53_PAD_CSI0_DAT9__ECSPI2_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT9__USBOH3_USBH3_PWR (_MX53_PAD_CSI0_DAT9__USBOH3_USBH3_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_CSI0_DAT9__I2C1_SCL (_MX53_PAD_CSI0_DAT9__I2C1_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_CSI0_DAT9__I2C1_SCL (_MX53_PAD_CSI0_DAT9__I2C1_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_CSI0_DAT9__EMI_EMI_DEBUG_38 (_MX53_PAD_CSI0_DAT9__EMI_EMI_DEBUG_38 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT9__TPIU_TRACE_6 (_MX53_PAD_CSI0_DAT9__TPIU_TRACE_6 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_CSI0_DAT10__IPU_CSI0_D_10 (_MX53_PAD_CSI0_DAT10__IPU_CSI0_D_10 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1631,25 +1634,25 @@ #define MX53_PAD_EIM_EB2__CCM_DI1_EXT_CLK (_MX53_PAD_EIM_EB2__CCM_DI1_EXT_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_EB2__IPU_SER_DISP1_CS (_MX53_PAD_EIM_EB2__IPU_SER_DISP1_CS | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_EB2__ECSPI1_SS0 (_MX53_PAD_EIM_EB2__ECSPI1_SS0 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_EB2__I2C2_SCL (_MX53_PAD_EIM_EB2__I2C2_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_EB2__I2C2_SCL (_MX53_PAD_EIM_EB2__I2C2_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D16__EMI_WEIM_D_16 (_MX53_PAD_EIM_D16__EMI_WEIM_D_16 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D16__GPIO3_16 (_MX53_PAD_EIM_D16__GPIO3_16 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D16__IPU_DI0_PIN5 (_MX53_PAD_EIM_D16__IPU_DI0_PIN5 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D16__IPU_DISPB1_SER_CLK (_MX53_PAD_EIM_D16__IPU_DISPB1_SER_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D16__ECSPI1_SCLK (_MX53_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_D16__I2C2_SDA (_MX53_PAD_EIM_D16__I2C2_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_D16__I2C2_SDA (_MX53_PAD_EIM_D16__I2C2_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D17__EMI_WEIM_D_17 (_MX53_PAD_EIM_D17__EMI_WEIM_D_17 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D17__GPIO3_17 (_MX53_PAD_EIM_D17__GPIO3_17 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D17__IPU_DI0_PIN6 (_MX53_PAD_EIM_D17__IPU_DI0_PIN6 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D17__IPU_DISPB1_SER_DIN (_MX53_PAD_EIM_D17__IPU_DISPB1_SER_DIN | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D17__ECSPI1_MISO (_MX53_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_D17__I2C3_SCL (_MX53_PAD_EIM_D17__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_D17__I2C3_SCL (_MX53_PAD_EIM_D17__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D18__EMI_WEIM_D_18 (_MX53_PAD_EIM_D18__EMI_WEIM_D_18 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D18__GPIO3_18 (_MX53_PAD_EIM_D18__GPIO3_18 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D18__IPU_DI0_PIN7 (_MX53_PAD_EIM_D18__IPU_DI0_PIN7 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D18__IPU_DISPB1_SER_DIO (_MX53_PAD_EIM_D18__IPU_DISPB1_SER_DIO | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D18__ECSPI1_MOSI (_MX53_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_D18__I2C3_SDA (_MX53_PAD_EIM_D18__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_D18__I2C3_SDA (_MX53_PAD_EIM_D18__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D18__IPU_DI1_D0_CS (_MX53_PAD_EIM_D18__IPU_DI1_D0_CS | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D19__EMI_WEIM_D_19 (_MX53_PAD_EIM_D19__EMI_WEIM_D_19 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D19__GPIO3_19 (_MX53_PAD_EIM_D19__GPIO3_19 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1672,7 +1675,7 @@ #define MX53_PAD_EIM_D21__IPU_DI0_PIN17 (_MX53_PAD_EIM_D21__IPU_DI0_PIN17 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK (_MX53_PAD_EIM_D21__IPU_DISPB0_SER_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D21__CSPI_SCLK (_MX53_PAD_EIM_D21__CSPI_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_D21__I2C1_SCL (_MX53_PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_D21__I2C1_SCL (_MX53_PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D21__USBOH3_USBOTG_OC (_MX53_PAD_EIM_D21__USBOH3_USBOTG_OC | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D22__EMI_WEIM_D_22 (_MX53_PAD_EIM_D22__EMI_WEIM_D_22 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D22__GPIO3_22 (_MX53_PAD_EIM_D22__GPIO3_22 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -1732,7 +1735,7 @@ #define MX53_PAD_EIM_D28__UART2_CTS (_MX53_PAD_EIM_D28__UART2_CTS | MUX_PAD_CTRL(MX53_UART_PAD_CTRL)) #define MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO (_MX53_PAD_EIM_D28__IPU_DISPB0_SER_DIO | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D28__CSPI_MOSI (_MX53_PAD_EIM_D28__CSPI_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_EIM_D28__I2C1_SDA (_MX53_PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_EIM_D28__I2C1_SDA (_MX53_PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_EIM_D28__IPU_EXT_TRIG (_MX53_PAD_EIM_D28__IPU_EXT_TRIG | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D28__IPU_DI0_PIN13 (_MX53_PAD_EIM_D28__IPU_DI0_PIN13 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_EIM_D29__EMI_WEIM_D_29 (_MX53_PAD_EIM_D29__EMI_WEIM_D_29 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -2297,7 +2300,7 @@ #define MX53_PAD_GPIO_9__SCC_FAIL_STATE (_MX53_PAD_GPIO_9__SCC_FAIL_STATE | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_3__ESAI1_HCKR (_MX53_PAD_GPIO_3__ESAI1_HCKR | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_3__GPIO1_3 (_MX53_PAD_GPIO_3__GPIO1_3 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_GPIO_3__I2C3_SCL (_MX53_PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_GPIO_3__I2C3_SCL (_MX53_PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_GPIO_3__DPLLIP1_TOG_EN (_MX53_PAD_GPIO_3__DPLLIP1_TOG_EN | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_3__CCM_CLKO2 (_MX53_PAD_GPIO_3__CCM_CLKO2 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_3__OBSERVE_MUX_OBSRV_INT_OUT0 (_MX53_PAD_GPIO_3__OBSERVE_MUX_OBSRV_INT_OUT0 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -2305,7 +2308,7 @@ #define MX53_PAD_GPIO_3__MLB_MLBCLK (_MX53_PAD_GPIO_3__MLB_MLBCLK | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_6__ESAI1_SCKT (_MX53_PAD_GPIO_6__ESAI1_SCKT | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_6__GPIO1_6 (_MX53_PAD_GPIO_6__GPIO1_6 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_GPIO_6__I2C3_SDA (_MX53_PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_GPIO_6__I2C3_SDA (_MX53_PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_GPIO_6__CCM_CCM_OUT_0 (_MX53_PAD_GPIO_6__CCM_CCM_OUT_0 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_6__CSU_CSU_INT_DEB (_MX53_PAD_GPIO_6__CSU_CSU_INT_DEB | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_6__OBSERVE_MUX_OBSRV_INT_OUT1 (_MX53_PAD_GPIO_6__OBSERVE_MUX_OBSRV_INT_OUT1 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -2333,7 +2336,7 @@ #define MX53_PAD_GPIO_5__CCM_CLKO (_MX53_PAD_GPIO_5__CCM_CLKO | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_5__CSU_CSU_ALARM_AUT_2 (_MX53_PAD_GPIO_5__CSU_CSU_ALARM_AUT_2 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_5__OBSERVE_MUX_OBSRV_INT_OUT4 (_MX53_PAD_GPIO_5__OBSERVE_MUX_OBSRV_INT_OUT4 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_GPIO_5__I2C3_SCL (_MX53_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_GPIO_5__I2C3_SCL (_MX53_PAD_GPIO_5__I2C3_SCL | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_GPIO_5__CCM_PLL1_BYP (_MX53_PAD_GPIO_5__CCM_PLL1_BYP | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_7__ESAI1_TX4_RX1 (_MX53_PAD_GPIO_7__ESAI1_TX4_RX1 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_7__GPIO1_7 (_MX53_PAD_GPIO_7__GPIO1_7 | MUX_PAD_CTRL(NO_PAD_CTRL)) @@ -2356,7 +2359,7 @@ #define MX53_PAD_GPIO_16__TZIC_PWRFAIL_INT (_MX53_PAD_GPIO_16__TZIC_PWRFAIL_INT | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_16__RTC_CE_RTC_EXT_TRIG1 (_MX53_PAD_GPIO_16__RTC_CE_RTC_EXT_TRIG1 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_16__SPDIF_IN1 (_MX53_PAD_GPIO_16__SPDIF_IN1 | MUX_PAD_CTRL(NO_PAD_CTRL)) -#define MX53_PAD_GPIO_16__I2C3_SDA (_MX53_PAD_GPIO_16__I2C3_SDA | MUX_PAD_CTRL(NO_PAD_CTRL)) +#define MX53_PAD_GPIO_16__I2C3_SDA (_MX53_PAD_GPIO_16__I2C3_SDA | MUX_PAD_CTRL(PAD_CTRL_I2C)) #define MX53_PAD_GPIO_16__SJC_DE_B (_MX53_PAD_GPIO_16__SJC_DE_B | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_17__ESAI1_TX0 (_MX53_PAD_GPIO_17__ESAI1_TX0 | MUX_PAD_CTRL(NO_PAD_CTRL)) #define MX53_PAD_GPIO_17__GPIO7_12 (_MX53_PAD_GPIO_17__GPIO7_12 | MUX_PAD_CTRL(NO_PAD_CTRL)) diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig index 6e6735f04ee..bb8f4a6b3e3 100644 --- a/arch/arm/plat-omap/Kconfig +++ b/arch/arm/plat-omap/Kconfig @@ -13,6 +13,7 @@ config ARCH_OMAP1 bool "TI OMAP1" select CLKDEV_LOOKUP select CLKSRC_MMIO + select GENERIC_IRQ_CHIP help "Systems based on omap7xx, omap15xx or omap16xx" diff --git a/arch/arm/plat-omap/include/plat/dma.h b/arch/arm/plat-omap/include/plat/dma.h index d1c916fcf77..dc562a5c0a8 100644 --- a/arch/arm/plat-omap/include/plat/dma.h +++ b/arch/arm/plat-omap/include/plat/dma.h @@ -195,6 +195,11 @@ #define OMAP36XX_DMA_UART4_TX 81 /* S_DMA_80 */ #define OMAP36XX_DMA_UART4_RX 82 /* S_DMA_81 */ + +/* Only for AM35xx */ +#define AM35XX_DMA_UART4_TX 54 +#define AM35XX_DMA_UART4_RX 55 + /*----------------------------------------------------------------------------*/ #define OMAP1_DMA_TOUT_IRQ (1 << 0) diff --git a/arch/arm/plat-omap/include/plat/irqs.h b/arch/arm/plat-omap/include/plat/irqs.h index 926d25c780f..30e10719b77 100644 --- a/arch/arm/plat-omap/include/plat/irqs.h +++ b/arch/arm/plat-omap/include/plat/irqs.h @@ -357,6 +357,7 @@ #define INT_35XX_EMAC_C0_TX_PULSE_IRQ 69 #define INT_35XX_EMAC_C0_MISC_PULSE_IRQ 70 #define INT_35XX_USBOTG_IRQ 71 +#define INT_35XX_UART4 84 #define INT_35XX_CCDC_VD0_IRQ 88 #define INT_35XX_CCDC_VD1_IRQ 92 #define INT_35XX_CCDC_VD2_IRQ 93 diff --git a/arch/arm/plat-omap/include/plat/serial.h b/arch/arm/plat-omap/include/plat/serial.h index 2723f9166ea..de3b10c1812 100644 --- a/arch/arm/plat-omap/include/plat/serial.h +++ b/arch/arm/plat-omap/include/plat/serial.h @@ -56,6 +56,9 @@ #define TI816X_UART2_BASE 0x48022000 #define TI816X_UART3_BASE 0x48024000 +/* AM3505/3517 UART4 */ +#define AM35XX_UART4_BASE 0x4809E000 /* Only on AM3505/3517 */ + /* External port on Zoom2/3 */ #define ZOOM_UART_BASE 0x10000000 #define ZOOM_UART_VIRT 0xfa400000 diff --git a/arch/arm/plat-omap/iovmm.c b/arch/arm/plat-omap/iovmm.c index c60737c49a3..79e7fedb860 100644 --- a/arch/arm/plat-omap/iovmm.c +++ b/arch/arm/plat-omap/iovmm.c @@ -423,9 +423,6 @@ static void sgtable_fill_kmalloc(struct sg_table *sgt, u32 pa, u32 da, { unsigned int i; struct scatterlist *sg; - void *va; - - va = phys_to_virt(pa); for_each_sg(sgt->sgl, sg, sgt->nents, i) { unsigned bytes; diff --git a/arch/arm/plat-omap/omap_device.c b/arch/arm/plat-omap/omap_device.c index b6b40974495..02609eee056 100644 --- a/arch/arm/plat-omap/omap_device.c +++ b/arch/arm/plat-omap/omap_device.c @@ -615,6 +615,9 @@ static int _od_resume_noirq(struct device *dev) return pm_generic_resume_noirq(dev); } +#else +#define _od_suspend_noirq NULL +#define _od_resume_noirq NULL #endif static struct dev_pm_domain omap_device_pm_domain = { @@ -622,7 +625,8 @@ static struct dev_pm_domain omap_device_pm_domain = { SET_RUNTIME_PM_OPS(_od_runtime_suspend, _od_runtime_resume, _od_runtime_idle) USE_PLATFORM_PM_SLEEP_OPS - SET_SYSTEM_SLEEP_PM_OPS(_od_suspend_noirq, _od_resume_noirq) + .suspend_noirq = _od_suspend_noirq, + .resume_noirq = _od_resume_noirq, } }; diff --git a/arch/arm/plat-s5p/clock.c b/arch/arm/plat-s5p/clock.c index 02af235298e..5f84a3f13ef 100644 --- a/arch/arm/plat-s5p/clock.c +++ b/arch/arm/plat-s5p/clock.c @@ -192,7 +192,7 @@ unsigned long s5p_spdif_get_rate(struct clk *clk) if (IS_ERR(pclk)) return -EINVAL; - rate = pclk->ops->get_rate(clk); + rate = pclk->ops->get_rate(pclk); clk_put(pclk); return rate; diff --git a/arch/arm/plat-s5p/irq-gpioint.c b/arch/arm/plat-s5p/irq-gpioint.c index 327ab9f662e..f88216d2399 100644 --- a/arch/arm/plat-s5p/irq-gpioint.c +++ b/arch/arm/plat-s5p/irq-gpioint.c @@ -23,6 +23,8 @@ #include <plat/gpio-core.h> #include <plat/gpio-cfg.h> +#include <asm/mach/irq.h> + #define GPIO_BASE(chip) (((unsigned long)(chip)->base) & 0xFFFFF000u) #define CON_OFFSET 0x700 @@ -81,6 +83,9 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc) int group, pend_offset, mask_offset; unsigned int pend, mask; + struct irq_chip *chip = irq_get_chip(irq); + chained_irq_enter(chip, desc); + for (group = 0; group < bank->nr_groups; group++) { struct s3c_gpio_chip *chip = bank->chips[group]; if (!chip) @@ -102,23 +107,25 @@ static void s5p_gpioint_handler(unsigned int irq, struct irq_desc *desc) pend &= ~BIT(offset); } } + chained_irq_exit(chip, desc); } static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip) { static int used_gpioint_groups = 0; int group = chip->group; - struct s5p_gpioint_bank *bank = NULL; + struct s5p_gpioint_bank *b, *bank = NULL; struct irq_chip_generic *gc; struct irq_chip_type *ct; if (used_gpioint_groups >= S5P_GPIOINT_GROUP_COUNT) return -ENOMEM; - list_for_each_entry(bank, &banks, list) { - if (group >= bank->start && - group < bank->start + bank->nr_groups) + list_for_each_entry(b, &banks, list) { + if (group >= b->start && group < b->start + b->nr_groups) { + bank = b; break; + } } if (!bank) return -EINVAL; diff --git a/arch/arm/plat-samsung/clock.c b/arch/arm/plat-samsung/clock.c index 302c42670bd..3b4451979d1 100644 --- a/arch/arm/plat-samsung/clock.c +++ b/arch/arm/plat-samsung/clock.c @@ -64,6 +64,17 @@ static LIST_HEAD(clocks); */ DEFINE_SPINLOCK(clocks_lock); +/* Global watchdog clock used by arch_wtd_reset() callback */ +struct clk *s3c2410_wdtclk; +static int __init s3c_wdt_reset_init(void) +{ + s3c2410_wdtclk = clk_get(NULL, "watchdog"); + if (IS_ERR(s3c2410_wdtclk)) + printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__); + return 0; +} +arch_initcall(s3c_wdt_reset_init); + /* enable and disable calls for use with the clk struct */ static int clk_null_enable(struct clk *clk, int enable) diff --git a/arch/arm/plat-samsung/include/plat/backlight.h b/arch/arm/plat-samsung/include/plat/backlight.h index 51d8da846a6..ad530c78fe8 100644 --- a/arch/arm/plat-samsung/include/plat/backlight.h +++ b/arch/arm/plat-samsung/include/plat/backlight.h @@ -20,7 +20,7 @@ struct samsung_bl_gpio_info { int func; }; -extern void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info, +extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info, struct platform_pwm_backlight_data *bl_data); #endif /* __ASM_PLAT_BACKLIGHT_H */ diff --git a/arch/arm/plat-samsung/include/plat/clock.h b/arch/arm/plat-samsung/include/plat/clock.h index 87d5b38a86f..73c66d4d10f 100644 --- a/arch/arm/plat-samsung/include/plat/clock.h +++ b/arch/arm/plat-samsung/include/plat/clock.h @@ -9,6 +9,9 @@ * published by the Free Software Foundation. */ +#ifndef __ASM_PLAT_CLOCK_H +#define __ASM_PLAT_CLOCK_H __FILE__ + #include <linux/spinlock.h> #include <linux/clkdev.h> @@ -121,3 +124,8 @@ extern int s3c64xx_sclk_ctrl(struct clk *clk, int enable); extern void s3c_pwmclk_init(void); +/* Global watchdog clock used by arch_wtd_reset() callback */ + +extern struct clk *s3c2410_wdtclk; + +#endif /* __ASM_PLAT_CLOCK_H */ diff --git a/arch/arm/plat-samsung/include/plat/watchdog-reset.h b/arch/arm/plat-samsung/include/plat/watchdog-reset.h index 54b762acb5a..40dbb2b0ae2 100644 --- a/arch/arm/plat-samsung/include/plat/watchdog-reset.h +++ b/arch/arm/plat-samsung/include/plat/watchdog-reset.h @@ -10,6 +10,7 @@ * published by the Free Software Foundation. */ +#include <plat/clock.h> #include <plat/regs-watchdog.h> #include <mach/map.h> @@ -19,17 +20,12 @@ static inline void arch_wdt_reset(void) { - struct clk *wdtclk; - printk("arch_reset: attempting watchdog reset\n"); __raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */ - wdtclk = clk_get(NULL, "watchdog"); - if (!IS_ERR(wdtclk)) { - clk_enable(wdtclk); - } else - printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__); + if (s3c2410_wdtclk) + clk_enable(s3c2410_wdtclk); /* put initial values into count and data */ __raw_writel(0x80, S3C2410_WTCNT); diff --git a/arch/arm/plat-samsung/irq-vic-timer.c b/arch/arm/plat-samsung/irq-vic-timer.c index f714d060370..51583cd3016 100644 --- a/arch/arm/plat-samsung/irq-vic-timer.c +++ b/arch/arm/plat-samsung/irq-vic-timer.c @@ -22,9 +22,14 @@ #include <plat/irq-vic-timer.h> #include <plat/regs-timer.h> +#include <asm/mach/irq.h> + static void s3c_irq_demux_vic_timer(unsigned int irq, struct irq_desc *desc) { + struct irq_chip *chip = irq_get_chip(irq); + chained_irq_enter(chip, desc); generic_handle_irq((int)desc->irq_data.handler_data); + chained_irq_exit(chip, desc); } /* We assume the IRQ_TIMER0..IRQ_TIMER4 range is continuous. */ diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 3b3776d0a1a..62cc8f98117 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -351,7 +351,7 @@ centro MACH_CENTRO CENTRO 1944 nokia_rx51 MACH_NOKIA_RX51 NOKIA_RX51 1955 omap_zoom2 MACH_OMAP_ZOOM2 OMAP_ZOOM2 1967 cpuat9260 MACH_CPUAT9260 CPUAT9260 1973 -eukrea_cpuimx27 MACH_CPUIMX27 CPUIMX27 1975 +eukrea_cpuimx27 MACH_EUKREA_CPUIMX27 EUKREA_CPUIMX27 1975 acs5k MACH_ACS5K ACS5K 1982 snapper_9260 MACH_SNAPPER_9260 SNAPPER_9260 1987 dsm320 MACH_DSM320 DSM320 1988 @@ -476,8 +476,8 @@ cns3420vb MACH_CNS3420VB CNS3420VB 2776 omap4_panda MACH_OMAP4_PANDA OMAP4_PANDA 2791 ti8168evm MACH_TI8168EVM TI8168EVM 2800 teton_bga MACH_TETON_BGA TETON_BGA 2816 -eukrea_cpuimx25sd MACH_EUKREA_CPUIMX25 EUKREA_CPUIMX25 2820 -eukrea_cpuimx35sd MACH_EUKREA_CPUIMX35 EUKREA_CPUIMX35 2821 +eukrea_cpuimx25sd MACH_EUKREA_CPUIMX25SD EUKREA_CPUIMX25SD 2820 +eukrea_cpuimx35sd MACH_EUKREA_CPUIMX35SD EUKREA_CPUIMX35SD 2821 eukrea_cpuimx51sd MACH_EUKREA_CPUIMX51SD EUKREA_CPUIMX51SD 2822 eukrea_cpuimx51 MACH_EUKREA_CPUIMX51 EUKREA_CPUIMX51 2823 smdkc210 MACH_SMDKC210 SMDKC210 2838 @@ -910,7 +910,7 @@ omapl138_case_a3 MACH_OMAPL138_CASE_A3 OMAPL138_CASE_A3 3280 uemd MACH_UEMD UEMD 3281 ccwmx51mut MACH_CCWMX51MUT CCWMX51MUT 3282 rockhopper MACH_ROCKHOPPER ROCKHOPPER 3283 -nookcolor MACH_NOOKCOLOR NOOKCOLOR 3284 +encore MACH_ENCORE ENCORE 3284 hkdkc100 MACH_HKDKC100 HKDKC100 3285 ts42xx MACH_TS42XX TS42XX 3286 aebl MACH_AEBL AEBL 3287 |