diff options
Diffstat (limited to 'arch/arm')
44 files changed, 486 insertions, 368 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index f1d9297b105..d56d21c0573 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1311,7 +1311,7 @@ config HZ config THUMB2_KERNEL bool "Compile the kernel in Thumb-2 mode" - depends on CPU_V7 && EXPERIMENTAL + depends on CPU_V7 && !CPU_V6 && EXPERIMENTAL select AEABI select ARM_ASM_UNIFIED help @@ -1759,7 +1759,7 @@ comment "At least one emulation must be selected" config FPE_NWFPE bool "NWFPE math emulation" - depends on !AEABI || OABI_COMPAT + depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL ---help--- Say Y to include the NWFPE floating point emulator in the kernel. This is necessary to run most binaries. Linux does not currently diff --git a/arch/arm/common/it8152.c b/arch/arm/common/it8152.c index 1bec96e8519..42ff90b46df 100644 --- a/arch/arm/common/it8152.c +++ b/arch/arm/common/it8152.c @@ -352,3 +352,4 @@ struct pci_bus * __init it8152_pci_scan_bus(int nr, struct pci_sys_data *sys) return pci_scan_bus(nr, &it8152_ops, sys); } +EXPORT_SYMBOL(dma_set_coherent_mask); diff --git a/arch/arm/include/asm/hardware/it8152.h b/arch/arm/include/asm/hardware/it8152.h index 21fa272301f..b2f95c72287 100644 --- a/arch/arm/include/asm/hardware/it8152.h +++ b/arch/arm/include/asm/hardware/it8152.h @@ -76,6 +76,7 @@ extern unsigned long it8152_base_address; IT8152_PD_IRQ(0) Audio controller (ACR) */ #define IT8152_IRQ(x) (IRQ_BOARD_START + (x)) +#define IT8152_LAST_IRQ (IRQ_BOARD_START + 40) /* IRQ-sources in 3 groups - local devices, LPC (serial), and external PCI */ #define IT8152_LD_IRQ_COUNT 9 diff --git a/arch/arm/include/asm/highmem.h b/arch/arm/include/asm/highmem.h index 1fc684e70ab..7080e2c8fa6 100644 --- a/arch/arm/include/asm/highmem.h +++ b/arch/arm/include/asm/highmem.h @@ -25,9 +25,6 @@ extern void *kmap_high(struct page *page); extern void *kmap_high_get(struct page *page); extern void kunmap_high(struct page *page); -extern void *kmap_high_l1_vipt(struct page *page, pte_t *saved_pte); -extern void kunmap_high_l1_vipt(struct page *page, pte_t saved_pte); - /* * The following functions are already defined by <linux/highmem.h> * when CONFIG_HIGHMEM is not set. diff --git a/arch/arm/include/asm/sizes.h b/arch/arm/include/asm/sizes.h index 4fc1565e4f9..316bb2b2be3 100644 --- a/arch/arm/include/asm/sizes.h +++ b/arch/arm/include/asm/sizes.h @@ -13,9 +13,6 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ -/* DO NOT EDIT!! - this file automatically generated - * from .s file by awk -f s2h.awk - */ /* Size definitions * Copyright (C) ARM Limited 1998. All rights reserved. */ @@ -25,6 +22,9 @@ /* handy sizes */ #define SZ_16 0x00000010 +#define SZ_32 0x00000020 +#define SZ_64 0x00000040 +#define SZ_128 0x00000080 #define SZ_256 0x00000100 #define SZ_512 0x00000200 diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index 1120f18a6b1..80025948b8a 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -150,6 +150,7 @@ extern unsigned int user_debug; #define rmb() dmb() #define wmb() mb() #else +#include <asm/memory.h> #define mb() do { if (arch_is_coherent()) dmb(); else barrier(); } while (0) #define rmb() do { if (arch_is_coherent()) dmb(); else barrier(); } while (0) #define wmb() do { if (arch_is_coherent()) dmb(); else barrier(); } while (0) diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 8bfa98757cd..80bf8cd88d7 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -29,6 +29,9 @@ ret_fast_syscall: ldr r1, [tsk, #TI_FLAGS] tst r1, #_TIF_WORK_MASK bne fast_work_pending +#if defined(CONFIG_IRQSOFF_TRACER) + asm_trace_hardirqs_on +#endif /* perform architecture specific actions before user return */ arch_ret_to_user r1, lr @@ -65,6 +68,9 @@ ret_slow_syscall: tst r1, #_TIF_WORK_MASK bne work_pending no_work_pending: +#if defined(CONFIG_IRQSOFF_TRACER) + asm_trace_hardirqs_on +#endif /* perform architecture specific actions before user return */ arch_ret_to_user r1, lr diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 8c195959025..9066473c0eb 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -310,7 +310,6 @@ asmlinkage void __cpuinit secondary_start_kernel(void) * All kernel threads share the same mm context; grab a * reference and switch to it. */ - atomic_inc(&mm->mm_users); atomic_inc(&mm->mm_count); current->active_mm = mm; cpumask_set_cpu(cpu, mm_cpumask(mm)); diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 62d686f0b42..d13add71f72 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -65,7 +65,7 @@ obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o obj-$(CONFIG_MACH_CPU9G20) += board-cpu9krea.o obj-$(CONFIG_MACH_STAMP9G20) += board-stamp9g20.o obj-$(CONFIG_MACH_PORTUXG20) += board-stamp9g20.o -obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o +obj-$(CONFIG_MACH_PCONTROL_G20) += board-pcontrol-g20.o board-stamp9g20.o # AT91SAM9260/AT91SAM9G20 board-specific support obj-$(CONFIG_MACH_SNAPPER_9260) += board-snapper9260.o diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index bba5a560e02..feb65787c30 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -31,6 +31,7 @@ #include <mach/board.h> #include <mach/at91sam9_smc.h> +#include <mach/stamp9g20.h> #include "sam9_smc.h" #include "generic.h" @@ -38,11 +39,7 @@ static void __init pcontrol_g20_map_io(void) { - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */ - at91_register_uart(0, 0, 0); + stamp9g20_map_io(); /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback A2 */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS @@ -54,9 +51,6 @@ static void __init pcontrol_g20_map_io(void) /* USART2 on ttyS3. (Rx, Tx) 9bit-Bus Multidrop-mode X4 */ at91_register_uart(AT91SAM9260_ID_US4, 3, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } @@ -66,38 +60,6 @@ static void __init init_irq(void) } -/* - * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB - */ -static struct atmel_nand_data __initdata nand_data = { - .ale = 21, - .cle = 22, - .rdy_pin = AT91_PIN_PC13, - .enable_pin = AT91_PIN_PC14, -}; - -/* - * Bus timings; unit = 7.57ns - */ -static struct sam9_smc_config __initdata nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE - | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, - .tdf_cycles = 3, -}; - static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .ncs_read_setup = 16, .nrd_setup = 18, @@ -138,14 +100,6 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { .tdf_cycles = 1, } }; -static void __init add_device_nand(void) -{ - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &nand_smc_config); - at91_add_device_nand(&nand_data); -} - - static void __init add_device_pcontrol(void) { /* configure chip-select 4 (IO compatible to 8051 X4 ) */ @@ -156,23 +110,6 @@ static void __init add_device_pcontrol(void) /* - * MCI (SD/MMC) - * det_pin, wp_pin and vcc_pin are not connected - */ -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) -static struct mci_platform_data __initdata mmc_data = { - .slot[0] = { - .bus_width = 4, - }, -}; -#else -static struct at91_mmc_data __initdata mmc_data = { - .wire4 = 1, -}; -#endif - - -/* * USB Host port */ static struct at91_usbh_data __initdata usbh_data = { @@ -265,42 +202,13 @@ static struct spi_board_info pcontrol_g20_spi_devices[] = { }; -/* - * Dallas 1-Wire DS2431 - */ -static struct w1_gpio_platform_data w1_gpio_pdata = { - .pin = AT91_PIN_PA29, - .is_open_drain = 1, -}; - -static struct platform_device w1_device = { - .name = "w1-gpio", - .id = -1, - .dev.platform_data = &w1_gpio_pdata, -}; - -static void add_wire1(void) -{ - at91_set_GPIO_periph(w1_gpio_pdata.pin, 1); - at91_set_multi_drive(w1_gpio_pdata.pin, 1); - platform_device_register(&w1_device); -} - - static void __init pcontrol_g20_board_init(void) { - at91_add_device_serial(); - add_device_nand(); -#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) - at91_add_device_mci(0, &mmc_data); -#else - at91_add_device_mmc(0, &mmc_data); -#endif + stamp9g20_board_init(); at91_add_device_usbh(&usbh_data); at91_add_device_eth(&macb_data); at91_add_device_i2c(pcontrol_g20_i2c_devices, ARRAY_SIZE(pcontrol_g20_i2c_devices)); - add_wire1(); add_device_pcontrol(); at91_add_device_spi(pcontrol_g20_spi_devices, ARRAY_SIZE(pcontrol_g20_spi_devices)); diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 5206eef4a67..f8902b11896 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -32,7 +32,7 @@ #include "generic.h" -static void __init portuxg20_map_io(void) +void __init stamp9g20_map_io(void) { /* Initialize processor: 18.432 MHz crystal */ at91sam9260_initialize(18432000); @@ -40,6 +40,24 @@ static void __init portuxg20_map_io(void) /* DGBU on ttyS0. (Rx & Tx only) */ at91_register_uart(0, 0, 0); + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); +} + +static void __init stamp9g20evb_map_io(void) +{ + stamp9g20_map_io(); + + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR + | ATMEL_UART_DCD | ATMEL_UART_RI); +} + +static void __init portuxg20_map_io(void) +{ + stamp9g20_map_io(); + /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR @@ -56,26 +74,6 @@ static void __init portuxg20_map_io(void) /* USART5 on ttyS6. (Rx, Tx only) */ at91_register_uart(AT91SAM9260_ID_US5, 6, 0); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); -} - -static void __init stamp9g20_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91sam9260_initialize(18432000); - - /* DGBU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR - | ATMEL_UART_DCD | ATMEL_UART_RI); - - /* set serial console to ttyS0 (ie, DBGU) */ - at91_set_serial_console(0); } static void __init init_irq(void) @@ -156,7 +154,7 @@ static struct at91_udc_data __initdata portuxg20_udc_data = { .pullup_pin = 0, /* pull-up driven by UDC */ }; -static struct at91_udc_data __initdata stamp9g20_udc_data = { +static struct at91_udc_data __initdata stamp9g20evb_udc_data = { .vbus_pin = AT91_PIN_PA22, .pullup_pin = 0, /* pull-up driven by UDC */ }; @@ -190,7 +188,7 @@ static struct gpio_led portuxg20_leds[] = { } }; -static struct gpio_led stamp9g20_leds[] = { +static struct gpio_led stamp9g20evb_leds[] = { { .name = "D8", .gpio = AT91_PIN_PB18, @@ -250,7 +248,7 @@ void add_w1(void) } -static void __init generic_board_init(void) +void __init stamp9g20_board_init(void) { /* Serial */ at91_add_device_serial(); @@ -262,34 +260,40 @@ static void __init generic_board_init(void) #else at91_add_device_mmc(0, &mmc_data); #endif - /* USB Host */ - at91_add_device_usbh(&usbh_data); - /* Ethernet */ - at91_add_device_eth(&macb_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); /* W1 */ add_w1(); } static void __init portuxg20_board_init(void) { - generic_board_init(); - /* SPI */ - at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ at91_add_device_udc(&portuxg20_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); + /* SPI */ + at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices)); /* LEDs */ at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds)); } -static void __init stamp9g20_board_init(void) +static void __init stamp9g20evb_board_init(void) { - generic_board_init(); + stamp9g20_board_init(); + /* USB Host */ + at91_add_device_usbh(&usbh_data); /* USB Device */ - at91_add_device_udc(&stamp9g20_udc_data); + at91_add_device_udc(&stamp9g20evb_udc_data); + /* Ethernet */ + at91_add_device_eth(&macb_data); + /* I2C */ + at91_add_device_i2c(NULL, 0); /* LEDs */ - at91_gpio_leds(stamp9g20_leds, ARRAY_SIZE(stamp9g20_leds)); + at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds)); } MACHINE_START(PORTUXG20, "taskit PortuxG20") @@ -305,7 +309,7 @@ MACHINE_START(STAMP9G20, "taskit Stamp9G20") /* Maintainer: taskit GmbH */ .boot_params = AT91_SDRAM_BASE + 0x100, .timer = &at91sam926x_timer, - .map_io = stamp9g20_map_io, + .map_io = stamp9g20evb_map_io, .init_irq = init_irq, - .init_machine = stamp9g20_board_init, + .init_machine = stamp9g20evb_board_init, MACHINE_END diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index 7525cee3983..9113da6845f 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -658,7 +658,7 @@ static void __init at91_upll_usbfs_clock_init(unsigned long main_clock) /* Now set uhpck values */ uhpck.parent = &utmi_clk; uhpck.pmc_mask = AT91SAM926x_PMC_UHP; - uhpck.rate_hz = utmi_clk.parent->rate_hz; + uhpck.rate_hz = utmi_clk.rate_hz; uhpck.rate_hz /= 1 + ((at91_sys_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8); } diff --git a/arch/arm/mach-at91/include/mach/at91_mci.h b/arch/arm/mach-at91/include/mach/at91_mci.h index 57f8ee15494..27ac6f550fe 100644 --- a/arch/arm/mach-at91/include/mach/at91_mci.h +++ b/arch/arm/mach-at91/include/mach/at91_mci.h @@ -74,6 +74,8 @@ #define AT91_MCI_TRTYP_BLOCK (0 << 19) #define AT91_MCI_TRTYP_MULTIPLE (1 << 19) #define AT91_MCI_TRTYP_STREAM (2 << 19) +#define AT91_MCI_TRTYP_SDIO_BYTE (4 << 19) +#define AT91_MCI_TRTYP_SDIO_BLOCK (5 << 19) #define AT91_MCI_BLKR 0x18 /* Block Register */ #define AT91_MCI_BLKR_BCNT(n) ((0xffff & (n)) << 0) /* Block count */ diff --git a/arch/arm/mach-at91/include/mach/stamp9g20.h b/arch/arm/mach-at91/include/mach/stamp9g20.h new file mode 100644 index 00000000000..6120f9c46d5 --- /dev/null +++ b/arch/arm/mach-at91/include/mach/stamp9g20.h @@ -0,0 +1,7 @@ +#ifndef __MACH_STAMP9G20_H +#define __MACH_STAMP9G20_H + +void stamp9g20_map_io(void); +void stamp9g20_board_init(void); + +#endif diff --git a/arch/arm/mach-ixp4xx/common-pci.c b/arch/arm/mach-ixp4xx/common-pci.c index 24498a932ba..a54b3db8036 100644 --- a/arch/arm/mach-ixp4xx/common-pci.c +++ b/arch/arm/mach-ixp4xx/common-pci.c @@ -513,4 +513,4 @@ int dma_set_coherent_mask(struct device *dev, u64 mask) EXPORT_SYMBOL(ixp4xx_pci_read); EXPORT_SYMBOL(ixp4xx_pci_write); - +EXPORT_SYMBOL(dma_set_coherent_mask); diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c index daf3993349f..2e3dd08ccc3 100644 --- a/arch/arm/mach-mmp/mmp2.c +++ b/arch/arm/mach-mmp/mmp2.c @@ -126,7 +126,6 @@ static APBC_CLK(twsi3, MMP2_TWSI3, 0, 26000000); static APBC_CLK(twsi4, MMP2_TWSI4, 0, 26000000); static APBC_CLK(twsi5, MMP2_TWSI5, 0, 26000000); static APBC_CLK(twsi6, MMP2_TWSI6, 0, 26000000); -static APBC_CLK(rtc, MMP2_RTC, 0, 32768); static APMU_CLK(nand, NAND, 0xbf, 100000000); diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c index 86c9b210295..9db9203667d 100644 --- a/arch/arm/mach-omap2/board-zoom-peripherals.c +++ b/arch/arm/mach-omap2/board-zoom-peripherals.c @@ -216,7 +216,7 @@ static struct omap2_hsmmc_info mmc[] __initdata = { { .name = "wl1271", .mmc = 3, - .caps = MMC_CAP_4_BIT_DATA, + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, .gpio_wp = -EINVAL, .gpio_cd = -EINVAL, .nonremovable = true, diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 40562ddd3ee..a1939b1e6f8 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -297,7 +297,7 @@ static int __init _omap2_init_reprogram_sdrc(void) return 0; dpll3_m2_ck = clk_get(NULL, "dpll3_m2_ck"); - if (!dpll3_m2_ck) + if (IS_ERR(dpll3_m2_ck)) return -EINVAL; rate = clk_get_rate(dpll3_m2_ck); diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c index 5e81517a7af..a8afb610c7d 100644 --- a/arch/arm/mach-omap2/pm-debug.c +++ b/arch/arm/mach-omap2/pm-debug.c @@ -161,6 +161,23 @@ void omap2_pm_dump(int mode, int resume, unsigned int us) printk(KERN_INFO "%-20s: 0x%08x\n", regs[i].name, regs[i].val); } +void omap2_pm_wakeup_on_timer(u32 seconds, u32 milliseconds) +{ + u32 tick_rate, cycles; + + if (!seconds && !milliseconds) + return; + + tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gptimer_wakeup)); + cycles = tick_rate * seconds + tick_rate * milliseconds / 1000; + omap_dm_timer_stop(gptimer_wakeup); + omap_dm_timer_set_load_start(gptimer_wakeup, 0, 0xffffffff - cycles); + + pr_info("PM: Resume timer in %u.%03u secs" + " (%d ticks at %d ticks/sec.)\n", + seconds, milliseconds, cycles, tick_rate); +} + #ifdef CONFIG_DEBUG_FS #include <linux/debugfs.h> #include <linux/seq_file.h> @@ -354,23 +371,6 @@ void pm_dbg_update_time(struct powerdomain *pwrdm, int prev) pwrdm->timer = t; } -void omap2_pm_wakeup_on_timer(u32 seconds, u32 milliseconds) -{ - u32 tick_rate, cycles; - - if (!seconds && !milliseconds) - return; - - tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gptimer_wakeup)); - cycles = tick_rate * seconds + tick_rate * milliseconds / 1000; - omap_dm_timer_stop(gptimer_wakeup); - omap_dm_timer_set_load_start(gptimer_wakeup, 0, 0xffffffff - cycles); - - pr_info("PM: Resume timer in %u.%03u secs" - " (%d ticks at %d ticks/sec.)\n", - seconds, milliseconds, cycles, tick_rate); -} - static int clkdm_dbg_show_counter(struct clockdomain *clkdm, void *user) { struct seq_file *s = (struct seq_file *)user; diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c index c85923e56b8..aaeea49b9bd 100644 --- a/arch/arm/mach-omap2/pm24xx.c +++ b/arch/arm/mach-omap2/pm24xx.c @@ -53,6 +53,19 @@ #include <plat/powerdomain.h> #include <plat/clockdomain.h> +#ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state = PM_SUSPEND_ON; +static inline bool is_suspending(void) +{ + return (suspend_state != PM_SUSPEND_ON); +} +#else +static inline bool is_suspending(void) +{ + return false; +} +#endif + static void (*omap2_sram_idle)(void); static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl, void __iomem *sdrc_power); @@ -120,8 +133,9 @@ static void omap2_enter_full_retention(void) goto no_sleep; /* Block console output in case it is on one of the OMAP UARTs */ - if (try_acquire_console_sem()) - goto no_sleep; + if (!is_suspending()) + if (try_acquire_console_sem()) + goto no_sleep; omap_uart_prepare_idle(0); omap_uart_prepare_idle(1); @@ -136,7 +150,8 @@ static void omap2_enter_full_retention(void) omap_uart_resume_idle(1); omap_uart_resume_idle(0); - release_console_sem(); + if (!is_suspending()) + release_console_sem(); no_sleep: if (omap2_pm_debug) { @@ -284,6 +299,12 @@ out: local_irq_enable(); } +static int omap2_pm_begin(suspend_state_t state) +{ + suspend_state = state; + return 0; +} + static int omap2_pm_prepare(void) { /* We cannot sleep in idle until we have resumed */ @@ -333,10 +354,17 @@ static void omap2_pm_finish(void) enable_hlt(); } +static void omap2_pm_end(void) +{ + suspend_state = PM_SUSPEND_ON; +} + static struct platform_suspend_ops omap_pm_ops = { + .begin = omap2_pm_begin, .prepare = omap2_pm_prepare, .enter = omap2_pm_enter, .finish = omap2_pm_finish, + .end = omap2_pm_end, .valid = suspend_valid_only_mem, }; diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 0ec8a04b747..648b8c50d02 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -50,6 +50,19 @@ #include "sdrc.h" #include "control.h" +#ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state = PM_SUSPEND_ON; +static inline bool is_suspending(void) +{ + return (suspend_state != PM_SUSPEND_ON); +} +#else +static inline bool is_suspending(void) +{ + return false; +} +#endif + /* Scratchpad offsets */ #define OMAP343X_TABLE_ADDRESS_OFFSET 0xc4 #define OMAP343X_TABLE_VALUE_OFFSET 0xc0 @@ -387,10 +400,11 @@ void omap_sram_idle(void) } /* Block console output in case it is on one of the OMAP UARTs */ - if (per_next_state < PWRDM_POWER_ON || - core_next_state < PWRDM_POWER_ON) - if (try_acquire_console_sem()) - goto console_still_active; + if (!is_suspending()) + if (per_next_state < PWRDM_POWER_ON || + core_next_state < PWRDM_POWER_ON) + if (try_acquire_console_sem()) + goto console_still_active; /* PER */ if (per_next_state < PWRDM_POWER_ON) { @@ -470,7 +484,8 @@ void omap_sram_idle(void) omap_uart_resume_idle(3); } - release_console_sem(); + if (!is_suspending()) + release_console_sem(); console_still_active: /* Disable IO-PAD and IO-CHAIN wakeup */ @@ -514,8 +529,6 @@ out: } #ifdef CONFIG_SUSPEND -static suspend_state_t suspend_state; - static int omap3_pm_prepare(void) { disable_hlt(); diff --git a/arch/arm/mach-omap2/prcm-common.h b/arch/arm/mach-omap2/prcm-common.h index 298a22a754e..f81acee4738 100644 --- a/arch/arm/mach-omap2/prcm-common.h +++ b/arch/arm/mach-omap2/prcm-common.h @@ -243,13 +243,14 @@ #define OMAP24XX_EN_GPT1_MASK (1 << 0) /* PM_WKST_WKUP, CM_IDLEST_WKUP shared bits */ -#define OMAP24XX_ST_GPIOS_SHIFT (1 << 2) -#define OMAP24XX_ST_GPIOS_MASK 2 -#define OMAP24XX_ST_GPT1_SHIFT (1 << 0) -#define OMAP24XX_ST_GPT1_MASK 0 +#define OMAP24XX_ST_GPIOS_SHIFT 2 +#define OMAP24XX_ST_GPIOS_MASK (1 << 2) +#define OMAP24XX_ST_GPT1_SHIFT 0 +#define OMAP24XX_ST_GPT1_MASK (1 << 0) /* CM_IDLEST_MDM and PM_WKST_MDM shared bits */ -#define OMAP2430_ST_MDM_SHIFT (1 << 0) +#define OMAP2430_ST_MDM_SHIFT 0 +#define OMAP2430_ST_MDM_MASK (1 << 0) /* 3430 register bits shared between CM & PRM registers */ diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index dd235ecc9d6..c93e73d54dd 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -540,6 +540,7 @@ config MACH_ICONTROL config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x + select FB_W100 config MACH_E330 bool "Toshiba e330" diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c index d2060a1d1d6..e5c9932b758 100644 --- a/arch/arm/mach-pxa/palmtx.c +++ b/arch/arm/mach-pxa/palmtx.c @@ -241,7 +241,8 @@ static inline void palmtx_keys_init(void) {} /****************************************************************************** * NAND Flash ******************************************************************************/ -#if defined(CONFIG_MTD_NAND_GPIO) || defined(CONFIG_MTD_NAND_GPIO_MODULE) +#if defined(CONFIG_MTD_NAND_PLATFORM) || \ + defined(CONFIG_MTD_NAND_PLATFORM_MODULE) static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl) { diff --git a/arch/arm/mach-pxa/sleep.S b/arch/arm/mach-pxa/sleep.S index 52c30b01a67..ae008110db4 100644 --- a/arch/arm/mach-pxa/sleep.S +++ b/arch/arm/mach-pxa/sleep.S @@ -353,8 +353,8 @@ resume_turn_on_mmu: @ Let us ensure we jump to resume_after_mmu only when the mcr above @ actually took effect. They call it the "cpwait" operation. - mrc p15, 0, r1, c2, c0, 0 @ queue a dependency on CP15 - sub pc, r2, r1, lsr #32 @ jump to virtual addr + mrc p15, 0, r0, c2, c0, 0 @ queue a dependency on CP15 + sub pc, r2, r0, lsr #32 @ jump to virtual addr nop nop nop diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index fa2e5bffbb8..6983cb4d4ca 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -28,9 +28,16 @@ config S3C2412_DMA config S3C2412_PM bool + select S3C2412_PM_SLEEP help Internal config node to apply S3C2412 power management +config S3C2412_PM_SLEEP + bool + help + Internal config node to apply sleep for S3C2412 power management. + Can be selected by another SoCs with similar sleep procedure. + # Note, the S3C2412 IOtiming support is in plat-s3c24xx config S3C2412_CPUFREQ diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile index 530ec46cbae..6c48a91ea39 100644 --- a/arch/arm/mach-s3c2412/Makefile +++ b/arch/arm/mach-s3c2412/Makefile @@ -14,7 +14,8 @@ obj-$(CONFIG_CPU_S3C2412) += irq.o obj-$(CONFIG_CPU_S3C2412) += clock.o obj-$(CONFIG_CPU_S3C2412) += gpio.o obj-$(CONFIG_S3C2412_DMA) += dma.o -obj-$(CONFIG_S3C2412_PM) += pm.o sleep.o +obj-$(CONFIG_S3C2412_PM) += pm.o +obj-$(CONFIG_S3C2412_PM_SLEEP) += sleep.o obj-$(CONFIG_S3C2412_CPUFREQ) += cpu-freq.o # Machine support diff --git a/arch/arm/mach-s3c2416/Kconfig b/arch/arm/mach-s3c2416/Kconfig index 27b3e7c9d61..df8d14974c9 100644 --- a/arch/arm/mach-s3c2416/Kconfig +++ b/arch/arm/mach-s3c2416/Kconfig @@ -27,6 +27,7 @@ config S3C2416_DMA config S3C2416_PM bool + select S3C2412_PM_SLEEP help Internal config node to apply S3C2416 power management diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c index 28677caf361..461aa035afc 100644 --- a/arch/arm/mach-s5pv210/mach-aquila.c +++ b/arch/arm/mach-s5pv210/mach-aquila.c @@ -378,6 +378,12 @@ static struct max8998_regulator_data aquila_regulators[] = { static struct max8998_platform_data aquila_max8998_pdata = { .num_regulators = ARRAY_SIZE(aquila_regulators), .regulators = aquila_regulators, + .buck1_set1 = S5PV210_GPH0(3), + .buck1_set2 = S5PV210_GPH0(4), + .buck2_set3 = S5PV210_GPH0(5), + .buck1_max_voltage1 = 1200000, + .buck1_max_voltage2 = 1200000, + .buck2_max_voltage = 1200000, }; #endif diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index b1dcf964a76..e22d5112fd4 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -518,6 +518,12 @@ static struct max8998_regulator_data goni_regulators[] = { static struct max8998_platform_data goni_max8998_pdata = { .num_regulators = ARRAY_SIZE(goni_regulators), .regulators = goni_regulators, + .buck1_set1 = S5PV210_GPH0(3), + .buck1_set2 = S5PV210_GPH0(4), + .buck2_set3 = S5PV210_GPH0(5), + .buck1_max_voltage1 = 1200000, + .buck1_max_voltage2 = 1200000, + .buck2_max_voltage = 1200000, }; #endif diff --git a/arch/arm/mach-shmobile/include/mach/entry-macro.S b/arch/arm/mach-shmobile/include/mach/entry-macro.S index a285d13c741..f428c4db2b6 100644 --- a/arch/arm/mach-shmobile/include/mach/entry-macro.S +++ b/arch/arm/mach-shmobile/include/mach/entry-macro.S @@ -1,4 +1,5 @@ /* + * Copyright (C) 2010 Magnus Damm * Copyright (C) 2008 Renesas Solutions Corp. * * This program is free software; you can redistribute it and/or modify @@ -14,24 +15,45 @@ * along with this program; if not, write to the Free Software * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -#include <mach/hardware.h> #include <mach/irqs.h> +#define INTCA_BASE 0xe6980000 +#define INTFLGA_OFFS 0x00000018 /* accept pending interrupt */ +#define INTEVTA_OFFS 0x00000020 /* vector number of accepted interrupt */ +#define INTLVLA_OFFS 0x00000030 /* priority level of accepted interrupt */ +#define INTLVLB_OFFS 0x00000034 /* previous priority level */ + .macro disable_fiq .endm .macro get_irqnr_preamble, base, tmp - ldr \base, =INTFLGA + ldr \base, =INTCA_BASE .endm .macro arch_ret_to_user, tmp1, tmp2 .endm .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqnr, [\base] + /* The single INTFLGA read access below results in the following: + * + * 1. INTLVLB is updated with old priority value from INTLVLA + * 2. Highest priority interrupt is accepted + * 3. INTLVLA is updated to contain priority of accepted interrupt + * 4. Accepted interrupt vector is stored in INTFLGA and INTEVTA + */ + ldr \irqnr, [\base, #INTFLGA_OFFS] + + /* Restore INTLVLA with the value saved in INTLVLB. + * This is required to support interrupt priorities properly. + */ + ldrb \tmp, [\base, #INTLVLB_OFFS] + strb \tmp, [\base, #INTLVLA_OFFS] + + /* Handle invalid vector number case */ cmp \irqnr, #0 beq 1000f - /* intevt to irq number */ + + /* Convert vector to irq number, same as the evt2irq() macro */ lsr \irqnr, \irqnr, #0x5 subs \irqnr, \irqnr, #16 diff --git a/arch/arm/mach-shmobile/include/mach/vmalloc.h b/arch/arm/mach-shmobile/include/mach/vmalloc.h index 4aecf6e3a85..2b8fd8b942f 100644 --- a/arch/arm/mach-shmobile/include/mach/vmalloc.h +++ b/arch/arm/mach-shmobile/include/mach/vmalloc.h @@ -2,6 +2,6 @@ #define __ASM_MACH_VMALLOC_H /* Vmalloc at ... - 0xe5ffffff */ -#define VMALLOC_END 0xe6000000 +#define VMALLOC_END 0xe6000000UL #endif /* __ASM_MACH_VMALLOC_H */ diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c index 6e77c042d8e..e0b0e7a4ec6 100644 --- a/arch/arm/mm/cache-feroceon-l2.c +++ b/arch/arm/mm/cache-feroceon-l2.c @@ -13,13 +13,9 @@ */ #include <linux/init.h> +#include <linux/highmem.h> #include <asm/cacheflush.h> -#include <asm/kmap_types.h> -#include <asm/fixmap.h> -#include <asm/pgtable.h> -#include <asm/tlbflush.h> #include <plat/cache-feroceon-l2.h> -#include "mm.h" /* * Low-level cache maintenance operations. @@ -39,27 +35,30 @@ * between which we don't want to be preempted. */ -static inline unsigned long l2_start_va(unsigned long paddr) +static inline unsigned long l2_get_va(unsigned long paddr) { #ifdef CONFIG_HIGHMEM /* - * Let's do our own fixmap stuff in a minimal way here. * Because range ops can't be done on physical addresses, * we simply install a virtual mapping for it only for the * TLB lookup to occur, hence no need to flush the untouched - * memory mapping. This is protected with the disabling of - * interrupts by the caller. + * memory mapping afterwards (note: a cache flush may happen + * in some circumstances depending on the path taken in kunmap_atomic). */ - unsigned long idx = KM_L2_CACHE + KM_TYPE_NR * smp_processor_id(); - unsigned long vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx); - set_pte_ext(TOP_PTE(vaddr), pfn_pte(paddr >> PAGE_SHIFT, PAGE_KERNEL), 0); - local_flush_tlb_kernel_page(vaddr); - return vaddr + (paddr & ~PAGE_MASK); + void *vaddr = kmap_atomic_pfn(paddr >> PAGE_SHIFT); + return (unsigned long)vaddr + (paddr & ~PAGE_MASK); #else return __phys_to_virt(paddr); #endif } +static inline void l2_put_va(unsigned long vaddr) +{ +#ifdef CONFIG_HIGHMEM + kunmap_atomic((void *)vaddr); +#endif +} + static inline void l2_clean_pa(unsigned long addr) { __asm__("mcr p15, 1, %0, c15, c9, 3" : : "r" (addr)); @@ -76,13 +75,14 @@ static inline void l2_clean_pa_range(unsigned long start, unsigned long end) */ BUG_ON((start ^ end) >> PAGE_SHIFT); - raw_local_irq_save(flags); - va_start = l2_start_va(start); + va_start = l2_get_va(start); va_end = va_start + (end - start); + raw_local_irq_save(flags); __asm__("mcr p15, 1, %0, c15, c9, 4\n\t" "mcr p15, 1, %1, c15, c9, 5" : : "r" (va_start), "r" (va_end)); raw_local_irq_restore(flags); + l2_put_va(va_start); } static inline void l2_clean_inv_pa(unsigned long addr) @@ -106,13 +106,14 @@ static inline void l2_inv_pa_range(unsigned long start, unsigned long end) */ BUG_ON((start ^ end) >> PAGE_SHIFT); - raw_local_irq_save(flags); - va_start = l2_start_va(start); + va_start = l2_get_va(start); va_end = va_start + (end - start); + raw_local_irq_save(flags); __asm__("mcr p15, 1, %0, c15, c11, 4\n\t" "mcr p15, 1, %1, c15, c11, 5" : : "r" (va_start), "r" (va_end)); raw_local_irq_restore(flags); + l2_put_va(va_start); } static inline void l2_inv_all(void) diff --git a/arch/arm/mm/cache-v6.S b/arch/arm/mm/cache-v6.S index 99fa688dfad..c96fa1b3f49 100644 --- a/arch/arm/mm/cache-v6.S +++ b/arch/arm/mm/cache-v6.S @@ -203,6 +203,10 @@ ENTRY(v6_flush_kern_dcache_area) * - end - virtual end address of region */ v6_dma_inv_range: +#ifdef CONFIG_DMA_CACHE_RWFO + ldrb r2, [r0] @ read for ownership + strb r2, [r0] @ write for ownership +#endif tst r0, #D_CACHE_LINE_SIZE - 1 bic r0, r0, #D_CACHE_LINE_SIZE - 1 #ifdef HARVARD_CACHE @@ -211,6 +215,10 @@ v6_dma_inv_range: mcrne p15, 0, r0, c7, c11, 1 @ clean unified line #endif tst r1, #D_CACHE_LINE_SIZE - 1 +#ifdef CONFIG_DMA_CACHE_RWFO + ldrneb r2, [r1, #-1] @ read for ownership + strneb r2, [r1, #-1] @ write for ownership +#endif bic r1, r1, #D_CACHE_LINE_SIZE - 1 #ifdef HARVARD_CACHE mcrne p15, 0, r1, c7, c14, 1 @ clean & invalidate D line @@ -218,10 +226,6 @@ v6_dma_inv_range: mcrne p15, 0, r1, c7, c15, 1 @ clean & invalidate unified line #endif 1: -#ifdef CONFIG_DMA_CACHE_RWFO - ldr r2, [r0] @ read for ownership - str r2, [r0] @ write for ownership -#endif #ifdef HARVARD_CACHE mcr p15, 0, r0, c7, c6, 1 @ invalidate D line #else @@ -229,6 +233,10 @@ v6_dma_inv_range: #endif add r0, r0, #D_CACHE_LINE_SIZE cmp r0, r1 +#ifdef CONFIG_DMA_CACHE_RWFO + ldrlo r2, [r0] @ read for ownership + strlo r2, [r0] @ write for ownership +#endif blo 1b mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer @@ -263,12 +271,12 @@ v6_dma_clean_range: * - end - virtual end address of region */ ENTRY(v6_dma_flush_range) - bic r0, r0, #D_CACHE_LINE_SIZE - 1 -1: #ifdef CONFIG_DMA_CACHE_RWFO - ldr r2, [r0] @ read for ownership - str r2, [r0] @ write for ownership + ldrb r2, [r0] @ read for ownership + strb r2, [r0] @ write for ownership #endif + bic r0, r0, #D_CACHE_LINE_SIZE - 1 +1: #ifdef HARVARD_CACHE mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D line #else @@ -276,6 +284,10 @@ ENTRY(v6_dma_flush_range) #endif add r0, r0, #D_CACHE_LINE_SIZE cmp r0, r1 +#ifdef CONFIG_DMA_CACHE_RWFO + ldrlob r2, [r0] @ read for ownership + strlob r2, [r0] @ write for ownership +#endif blo 1b mov r0, #0 mcr p15, 0, r0, c7, c10, 4 @ drain write buffer diff --git a/arch/arm/mm/cache-v7.S b/arch/arm/mm/cache-v7.S index a3ebf7a4f49..6136e68ce95 100644 --- a/arch/arm/mm/cache-v7.S +++ b/arch/arm/mm/cache-v7.S @@ -173,15 +173,22 @@ ENTRY(v7_coherent_user_range) UNWIND(.fnstart ) dcache_line_size r2, r3 sub r3, r2, #1 - bic r0, r0, r3 + bic r12, r0, r3 1: - USER( mcr p15, 0, r0, c7, c11, 1 ) @ clean D line to the point of unification + USER( mcr p15, 0, r12, c7, c11, 1 ) @ clean D line to the point of unification + add r12, r12, r2 + cmp r12, r1 + blo 1b dsb - USER( mcr p15, 0, r0, c7, c5, 1 ) @ invalidate I line - add r0, r0, r2 + icache_line_size r2, r3 + sub r3, r2, #1 + bic r12, r0, r3 2: - cmp r0, r1 - blo 1b + USER( mcr p15, 0, r12, c7, c5, 1 ) @ invalidate I line + add r12, r12, r2 + cmp r12, r1 + blo 2b +3: mov r0, #0 ALT_SMP(mcr p15, 0, r0, c7, c1, 6) @ invalidate BTB Inner Shareable ALT_UP(mcr p15, 0, r0, c7, c5, 6) @ invalidate BTB @@ -194,10 +201,10 @@ ENTRY(v7_coherent_user_range) * isn't mapped, just try the next page. */ 9001: - mov r0, r0, lsr #12 - mov r0, r0, lsl #12 - add r0, r0, #4096 - b 2b + mov r12, r12, lsr #12 + mov r12, r12, lsl #12 + add r12, r12, #4096 + b 3b UNWIND(.fnend ) ENDPROC(v7_coherent_kern_range) ENDPROC(v7_coherent_user_range) diff --git a/arch/arm/mm/cache-xsc3l2.c b/arch/arm/mm/cache-xsc3l2.c index c3154928bcc..5a32020471e 100644 --- a/arch/arm/mm/cache-xsc3l2.c +++ b/arch/arm/mm/cache-xsc3l2.c @@ -17,14 +17,10 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include <linux/init.h> +#include <linux/highmem.h> #include <asm/system.h> #include <asm/cputype.h> #include <asm/cacheflush.h> -#include <asm/kmap_types.h> -#include <asm/fixmap.h> -#include <asm/pgtable.h> -#include <asm/tlbflush.h> -#include "mm.h" #define CR_L2 (1 << 26) @@ -71,16 +67,15 @@ static inline void xsc3_l2_inv_all(void) dsb(); } +static inline void l2_unmap_va(unsigned long va) +{ #ifdef CONFIG_HIGHMEM -#define l2_map_save_flags(x) raw_local_save_flags(x) -#define l2_map_restore_flags(x) raw_local_irq_restore(x) -#else -#define l2_map_save_flags(x) ((x) = 0) -#define l2_map_restore_flags(x) ((void)(x)) + if (va != -1) + kunmap_atomic((void *)va); #endif +} -static inline unsigned long l2_map_va(unsigned long pa, unsigned long prev_va, - unsigned long flags) +static inline unsigned long l2_map_va(unsigned long pa, unsigned long prev_va) { #ifdef CONFIG_HIGHMEM unsigned long va = prev_va & PAGE_MASK; @@ -89,17 +84,10 @@ static inline unsigned long l2_map_va(unsigned long pa, unsigned long prev_va, /* * Switching to a new page. Because cache ops are * using virtual addresses only, we must put a mapping - * in place for it. We also enable interrupts for a - * short while and disable them again to protect this - * mapping. + * in place for it. */ - unsigned long idx; - raw_local_irq_restore(flags); - idx = KM_L2_CACHE + KM_TYPE_NR * smp_processor_id(); - va = __fix_to_virt(FIX_KMAP_BEGIN + idx); - raw_local_irq_restore(flags | PSR_I_BIT); - set_pte_ext(TOP_PTE(va), pfn_pte(pa >> PAGE_SHIFT, PAGE_KERNEL), 0); - local_flush_tlb_kernel_page(va); + l2_unmap_va(prev_va); + va = (unsigned long)kmap_atomic_pfn(pa >> PAGE_SHIFT); } return va + (pa_offset >> (32 - PAGE_SHIFT)); #else @@ -109,7 +97,7 @@ static inline unsigned long l2_map_va(unsigned long pa, unsigned long prev_va, static void xsc3_l2_inv_range(unsigned long start, unsigned long end) { - unsigned long vaddr, flags; + unsigned long vaddr; if (start == 0 && end == -1ul) { xsc3_l2_inv_all(); @@ -117,13 +105,12 @@ static void xsc3_l2_inv_range(unsigned long start, unsigned long end) } vaddr = -1; /* to force the first mapping */ - l2_map_save_flags(flags); /* * Clean and invalidate partial first cache line. */ if (start & (CACHE_LINE_SIZE - 1)) { - vaddr = l2_map_va(start & ~(CACHE_LINE_SIZE - 1), vaddr, flags); + vaddr = l2_map_va(start & ~(CACHE_LINE_SIZE - 1), vaddr); xsc3_l2_clean_mva(vaddr); xsc3_l2_inv_mva(vaddr); start = (start | (CACHE_LINE_SIZE - 1)) + 1; @@ -133,7 +120,7 @@ static void xsc3_l2_inv_range(unsigned long start, unsigned long end) * Invalidate all full cache lines between 'start' and 'end'. */ while (start < (end & ~(CACHE_LINE_SIZE - 1))) { - vaddr = l2_map_va(start, vaddr, flags); + vaddr = l2_map_va(start, vaddr); xsc3_l2_inv_mva(vaddr); start += CACHE_LINE_SIZE; } @@ -142,31 +129,30 @@ static void xsc3_l2_inv_range(unsigned long start, unsigned long end) * Clean and invalidate partial last cache line. */ if (start < end) { - vaddr = l2_map_va(start, vaddr, flags); + vaddr = l2_map_va(start, vaddr); xsc3_l2_clean_mva(vaddr); xsc3_l2_inv_mva(vaddr); } - l2_map_restore_flags(flags); + l2_unmap_va(vaddr); dsb(); } static void xsc3_l2_clean_range(unsigned long start, unsigned long end) { - unsigned long vaddr, flags; + unsigned long vaddr; vaddr = -1; /* to force the first mapping */ - l2_map_save_flags(flags); start &= ~(CACHE_LINE_SIZE - 1); while (start < end) { - vaddr = l2_map_va(start, vaddr, flags); + vaddr = l2_map_va(start, vaddr); xsc3_l2_clean_mva(vaddr); start += CACHE_LINE_SIZE; } - l2_map_restore_flags(flags); + l2_unmap_va(vaddr); dsb(); } @@ -193,7 +179,7 @@ static inline void xsc3_l2_flush_all(void) static void xsc3_l2_flush_range(unsigned long start, unsigned long end) { - unsigned long vaddr, flags; + unsigned long vaddr; if (start == 0 && end == -1ul) { xsc3_l2_flush_all(); @@ -201,17 +187,16 @@ static void xsc3_l2_flush_range(unsigned long start, unsigned long end) } vaddr = -1; /* to force the first mapping */ - l2_map_save_flags(flags); start &= ~(CACHE_LINE_SIZE - 1); while (start < end) { - vaddr = l2_map_va(start, vaddr, flags); + vaddr = l2_map_va(start, vaddr); xsc3_l2_clean_mva(vaddr); xsc3_l2_inv_mva(vaddr); start += CACHE_LINE_SIZE; } - l2_map_restore_flags(flags); + l2_unmap_va(vaddr); dsb(); } diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index ac6a36142fc..809f1bf9fa2 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -17,6 +17,7 @@ #include <linux/init.h> #include <linux/device.h> #include <linux/dma-mapping.h> +#include <linux/highmem.h> #include <asm/memory.h> #include <asm/highmem.h> @@ -480,10 +481,10 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset, op(vaddr, len, dir); kunmap_high(page); } else if (cache_is_vipt()) { - pte_t saved_pte; - vaddr = kmap_high_l1_vipt(page, &saved_pte); + /* unmapped pages might still be cached */ + vaddr = kmap_atomic(page); op(vaddr + offset, len, dir); - kunmap_high_l1_vipt(page, saved_pte); + kunmap_atomic(vaddr); } } else { vaddr = page_address(page) + offset; diff --git a/arch/arm/mm/flush.c b/arch/arm/mm/flush.c index 391ffae7509..c29f2839f1d 100644 --- a/arch/arm/mm/flush.c +++ b/arch/arm/mm/flush.c @@ -10,6 +10,7 @@ #include <linux/module.h> #include <linux/mm.h> #include <linux/pagemap.h> +#include <linux/highmem.h> #include <asm/cacheflush.h> #include <asm/cachetype.h> @@ -180,10 +181,10 @@ void __flush_dcache_page(struct address_space *mapping, struct page *page) __cpuc_flush_dcache_area(addr, PAGE_SIZE); kunmap_high(page); } else if (cache_is_vipt()) { - pte_t saved_pte; - addr = kmap_high_l1_vipt(page, &saved_pte); + /* unmapped pages might still be cached */ + addr = kmap_atomic(page); __cpuc_flush_dcache_area(addr, PAGE_SIZE); - kunmap_high_l1_vipt(page, saved_pte); + kunmap_atomic(addr); } } diff --git a/arch/arm/mm/highmem.c b/arch/arm/mm/highmem.c index c435fd9e1da..807c0573abb 100644 --- a/arch/arm/mm/highmem.c +++ b/arch/arm/mm/highmem.c @@ -140,90 +140,3 @@ struct page *kmap_atomic_to_page(const void *ptr) pte = TOP_PTE(vaddr); return pte_page(*pte); } - -#ifdef CONFIG_CPU_CACHE_VIPT - -#include <linux/percpu.h> - -/* - * The VIVT cache of a highmem page is always flushed before the page - * is unmapped. Hence unmapped highmem pages need no cache maintenance - * in that case. - * - * However unmapped pages may still be cached with a VIPT cache, and - * it is not possible to perform cache maintenance on them using physical - * addresses unfortunately. So we have no choice but to set up a temporary - * virtual mapping for that purpose. - * - * Yet this VIPT cache maintenance may be triggered from DMA support - * functions which are possibly called from interrupt context. As we don't - * want to keep interrupt disabled all the time when such maintenance is - * taking place, we therefore allow for some reentrancy by preserving and - * restoring the previous fixmap entry before the interrupted context is - * resumed. If the reentrancy depth is 0 then there is no need to restore - * the previous fixmap, and leaving the current one in place allow it to - * be reused the next time without a TLB flush (common with DMA). - */ - -static DEFINE_PER_CPU(int, kmap_high_l1_vipt_depth); - -void *kmap_high_l1_vipt(struct page *page, pte_t *saved_pte) -{ - unsigned int idx, cpu; - int *depth; - unsigned long vaddr, flags; - pte_t pte, *ptep; - - if (!in_interrupt()) - preempt_disable(); - - cpu = smp_processor_id(); - depth = &per_cpu(kmap_high_l1_vipt_depth, cpu); - - idx = KM_L1_CACHE + KM_TYPE_NR * cpu; - vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx); - ptep = TOP_PTE(vaddr); - pte = mk_pte(page, kmap_prot); - - raw_local_irq_save(flags); - (*depth)++; - if (pte_val(*ptep) == pte_val(pte)) { - *saved_pte = pte; - } else { - *saved_pte = *ptep; - set_pte_ext(ptep, pte, 0); - local_flush_tlb_kernel_page(vaddr); - } - raw_local_irq_restore(flags); - - return (void *)vaddr; -} - -void kunmap_high_l1_vipt(struct page *page, pte_t saved_pte) -{ - unsigned int idx, cpu = smp_processor_id(); - int *depth = &per_cpu(kmap_high_l1_vipt_depth, cpu); - unsigned long vaddr, flags; - pte_t pte, *ptep; - - idx = KM_L1_CACHE + KM_TYPE_NR * cpu; - vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx); - ptep = TOP_PTE(vaddr); - pte = mk_pte(page, kmap_prot); - - BUG_ON(pte_val(*ptep) != pte_val(pte)); - BUG_ON(*depth <= 0); - - raw_local_irq_save(flags); - (*depth)--; - if (*depth != 0 && pte_val(pte) != pte_val(saved_pte)) { - set_pte_ext(ptep, saved_pte, 0); - local_flush_tlb_kernel_page(vaddr); - } - raw_local_irq_restore(flags); - - if (!in_interrupt()) - preempt_enable(); -} - -#endif /* CONFIG_CPU_CACHE_VIPT */ diff --git a/arch/arm/mm/proc-macros.S b/arch/arm/mm/proc-macros.S index 7d63beaf974..b795afd0a2c 100644 --- a/arch/arm/mm/proc-macros.S +++ b/arch/arm/mm/proc-macros.S @@ -61,17 +61,27 @@ .endm /* - * cache_line_size - get the cache line size from the CSIDR register - * (available on ARMv7+). It assumes that the CSSR register was configured - * to access the L1 data cache CSIDR. + * dcache_line_size - get the minimum D-cache line size from the CTR register + * on ARMv7. */ .macro dcache_line_size, reg, tmp - mrc p15, 1, \tmp, c0, c0, 0 @ read CSIDR - and \tmp, \tmp, #7 @ cache line size encoding - mov \reg, #16 @ size offset + mrc p15, 0, \tmp, c0, c0, 1 @ read ctr + lsr \tmp, \tmp, #16 + and \tmp, \tmp, #0xf @ cache line size encoding + mov \reg, #4 @ bytes per word mov \reg, \reg, lsl \tmp @ actual cache line size .endm +/* + * icache_line_size - get the minimum I-cache line size from the CTR register + * on ARMv7. + */ + .macro icache_line_size, reg, tmp + mrc p15, 0, \tmp, c0, c0, 1 @ read ctr + and \tmp, \tmp, #0xf @ cache line size encoding + mov \reg, #4 @ bytes per word + mov \reg, \reg, lsl \tmp @ actual cache line size + .endm /* * Sanity check the PTE configuration for the code below - which makes diff --git a/arch/arm/plat-omap/counter_32k.c b/arch/arm/plat-omap/counter_32k.c index 155fe43a672..8722a136f3a 100644 --- a/arch/arm/plat-omap/counter_32k.c +++ b/arch/arm/plat-omap/counter_32k.c @@ -16,6 +16,7 @@ #include <linux/init.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/err.h> #include <plat/common.h> #include <plat/board.h> @@ -164,7 +165,7 @@ static int __init omap_init_clocksource_32k(void) return -ENODEV; sync_32k_ick = clk_get(NULL, "omap_32ksync_ick"); - if (sync_32k_ick) + if (!IS_ERR(sync_32k_ick)) clk_enable(sync_32k_ick); clocksource_32k.mult = clocksource_hz2mult(32768, diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index e2c8eebe6b3..74dac419d32 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -166,7 +166,7 @@ static void __init omap_detect_sram(void) cpu_is_omap1710()) omap_sram_size = 0x4000; /* 16K */ else if (cpu_is_omap1611()) - omap_sram_size = 0x3e800; /* 250K */ + omap_sram_size = SZ_256K; else { printk(KERN_ERR "Could not detect SRAM size\n"); omap_sram_size = 0x4000; diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index 5a27b1b538f..eb105e61c74 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -8,7 +8,7 @@ config PLAT_S3C24XX default y select NO_IOPORT select ARCH_REQUIRE_GPIOLIB - select S3C_DEVICE_NAND + select S3C_DEV_NAND select S3C_GPIO_CFG_S3C24XX help Base platform code for any Samsung S3C24XX device diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 55590a4d87c..2fea897ebeb 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -12,7 +12,7 @@ # # http://www.arm.linux.org.uk/developer/machines/?action=new # -# Last update: Thu Sep 9 22:43:01 2010 +# Last update: Sun Dec 12 23:24:27 2010 # # machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number # @@ -2321,7 +2321,7 @@ mx31txtr MACH_MX31TXTR MX31TXTR 2332 u380 MACH_U380 U380 2333 oamp3_hualu MACH_HUALU_BOARD HUALU_BOARD 2334 npcmx50 MACH_NPCMX50 NPCMX50 2335 -mx51_lange51 MACH_MX51_LANGE51 MX51_LANGE51 2336 +mx51_efikamx MACH_MX51_EFIKAMX MX51_EFIKAMX 2336 mx51_lange52 MACH_MX51_LANGE52 MX51_LANGE52 2337 riom MACH_RIOM RIOM 2338 comcas MACH_COMCAS COMCAS 2339 @@ -2355,7 +2355,7 @@ at91sam9263cs MACH_AT91SAM9263CS AT91SAM9263CS 2366 csb732 MACH_CSB732 CSB732 2367 u8500 MACH_U8500 U8500 2368 huqiu MACH_HUQIU HUQIU 2369 -mx51_kunlun MACH_MX51_KUNLUN MX51_KUNLUN 2370 +mx51_efikasb MACH_MX51_EFIKASB MX51_EFIKASB 2370 pmt1g MACH_PMT1G PMT1G 2371 htcelf MACH_HTCELF HTCELF 2372 armadillo420 MACH_ARMADILLO420 ARMADILLO420 2373 @@ -2971,7 +2971,7 @@ premierwave_en MACH_PREMIERWAVE_EN PREMIERWAVE_EN 2985 wasabi MACH_WASABI WASABI 2986 vivow MACH_VIVOW VIVOW 2987 mx50_rdp MACH_MX50_RDP MX50_RDP 2988 -universal MACH_UNIVERSAL UNIVERSAL 2989 +universal_c210 MACH_UNIVERSAL_C210 UNIVERSAL_C210 2989 real6410 MACH_REAL6410 REAL6410 2990 spx_sakura MACH_SPX_SAKURA SPX_SAKURA 2991 ij3k_2440 MACH_IJ3K_2440 IJ3K_2440 2992 @@ -3044,3 +3044,178 @@ harvest_desoto MACH_HARVEST_DESOTO HARVEST_DESOTO 3059 msm8x60_qrdc MACH_MSM8X60_QRDC MSM8X60_QRDC 3060 spear900 MACH_SPEAR900 SPEAR900 3061 pcontrol_g20 MACH_PCONTROL_G20 PCONTROL_G20 3062 +rdstor MACH_RDSTOR RDSTOR 3063 +usdloader MACH_USDLOADER USDLOADER 3064 +tsoploader MACH_TSOPLOADER TSOPLOADER 3065 +kronos MACH_KRONOS KRONOS 3066 +ffcore MACH_FFCORE FFCORE 3067 +mone MACH_MONE MONE 3068 +unit2s MACH_UNIT2S UNIT2S 3069 +acer_a5 MACH_ACER_A5 ACER_A5 3070 +etherpro_isp MACH_ETHERPRO_ISP ETHERPRO_ISP 3071 +stretchs7000 MACH_STRETCHS7000 STRETCHS7000 3072 +p87_smartsim MACH_P87_SMARTSIM P87_SMARTSIM 3073 +tulip MACH_TULIP TULIP 3074 +sunflower MACH_SUNFLOWER SUNFLOWER 3075 +rib MACH_RIB RIB 3076 +clod MACH_CLOD CLOD 3077 +rump MACH_RUMP RUMP 3078 +tenderloin MACH_TENDERLOIN TENDERLOIN 3079 +shortloin MACH_SHORTLOIN SHORTLOIN 3080 +crespo MACH_CRESPO CRESPO 3081 +antares MACH_ANTARES ANTARES 3082 +wb40n MACH_WB40N WB40N 3083 +herring MACH_HERRING HERRING 3084 +naxy400 MACH_NAXY400 NAXY400 3085 +naxy1200 MACH_NAXY1200 NAXY1200 3086 +vpr200 MACH_VPR200 VPR200 3087 +bug20 MACH_BUG20 BUG20 3088 +goflexnet MACH_GOFLEXNET GOFLEXNET 3089 +torbreck MACH_TORBRECK TORBRECK 3090 +saarb_mg1 MACH_SAARB_MG1 SAARB_MG1 3091 +callisto MACH_CALLISTO CALLISTO 3092 +multhsu MACH_MULTHSU MULTHSU 3093 +saluda MACH_SALUDA SALUDA 3094 +pemp_omap3_apollo MACH_PEMP_OMAP3_APOLLO PEMP_OMAP3_APOLLO 3095 +vc0718 MACH_VC0718 VC0718 3096 +mvblx MACH_MVBLX MVBLX 3097 +inhand_apeiron MACH_INHAND_APEIRON INHAND_APEIRON 3098 +inhand_fury MACH_INHAND_FURY INHAND_FURY 3099 +inhand_siren MACH_INHAND_SIREN INHAND_SIREN 3100 +hdnvp MACH_HDNVP HDNVP 3101 +softwinner MACH_SOFTWINNER SOFTWINNER 3102 +prima2_evb MACH_PRIMA2_EVB PRIMA2_EVB 3103 +nas6210 MACH_NAS6210 NAS6210 3104 +unisdev MACH_UNISDEV UNISDEV 3105 +sbca11 MACH_SBCA11 SBCA11 3106 +saga MACH_SAGA SAGA 3107 +ns_k330 MACH_NS_K330 NS_K330 3108 +tanna MACH_TANNA TANNA 3109 +imate8502 MACH_IMATE8502 IMATE8502 3110 +aspen MACH_ASPEN ASPEN 3111 +daintree_cwac MACH_DAINTREE_CWAC DAINTREE_CWAC 3112 +zmx25 MACH_ZMX25 ZMX25 3113 +maple1 MACH_MAPLE1 MAPLE1 3114 +qsd8x72_surf MACH_QSD8X72_SURF QSD8X72_SURF 3115 +qsd8x72_ffa MACH_QSD8X72_FFA QSD8X72_FFA 3116 +abilene MACH_ABILENE ABILENE 3117 +eigen_ttr MACH_EIGEN_TTR EIGEN_TTR 3118 +iomega_ix2_200 MACH_IOMEGA_IX2_200 IOMEGA_IX2_200 3119 +coretec_vcx7400 MACH_CORETEC_VCX7400 CORETEC_VCX7400 3120 +santiago MACH_SANTIAGO SANTIAGO 3121 +mx257sol MACH_MX257SOL MX257SOL 3122 +strasbourg MACH_STRASBOURG STRASBOURG 3123 +msm8x60_fluid MACH_MSM8X60_FLUID MSM8X60_FLUID 3124 +smartqv5 MACH_SMARTQV5 SMARTQV5 3125 +smartqv3 MACH_SMARTQV3 SMARTQV3 3126 +smartqv7 MACH_SMARTQV7 SMARTQV7 3127 +paz00 MACH_PAZ00 PAZ00 3128 +acmenetusfoxg20 MACH_ACMENETUSFOXG20 ACMENETUSFOXG20 3129 +htcwillow MACH_HTCWILLOW HTCWILLOW 3130 +fwbd_0404 MACH_FWBD_0404 FWBD_0404 3131 +hdgu MACH_HDGU HDGU 3132 +pyramid MACH_PYRAMID PYRAMID 3133 +epiphan MACH_EPIPHAN EPIPHAN 3134 +omap_bender MACH_OMAP_BENDER OMAP_BENDER 3135 +gurnard MACH_GURNARD GURNARD 3136 +gtl_it5100 MACH_GTL_IT5100 GTL_IT5100 3137 +bcm2708 MACH_BCM2708 BCM2708 3138 +mx51_ggc MACH_MX51_GGC MX51_GGC 3139 +sharespace MACH_SHARESPACE SHARESPACE 3140 +haba_knx_explorer MACH_HABA_KNX_EXPLORER HABA_KNX_EXPLORER 3141 +simtec_kirkmod MACH_SIMTEC_KIRKMOD SIMTEC_KIRKMOD 3142 +crux MACH_CRUX CRUX 3143 +mx51_bravo MACH_MX51_BRAVO MX51_BRAVO 3144 +charon MACH_CHARON CHARON 3145 +picocom3 MACH_PICOCOM3 PICOCOM3 3146 +picocom4 MACH_PICOCOM4 PICOCOM4 3147 +serrano MACH_SERRANO SERRANO 3148 +doubleshot MACH_DOUBLESHOT DOUBLESHOT 3149 +evsy MACH_EVSY EVSY 3150 +huashan MACH_HUASHAN HUASHAN 3151 +lausanne MACH_LAUSANNE LAUSANNE 3152 +emerald MACH_EMERALD EMERALD 3153 +tqma35 MACH_TQMA35 TQMA35 3154 +marvel MACH_MARVEL MARVEL 3155 +manuae MACH_MANUAE MANUAE 3156 +chacha MACH_CHACHA CHACHA 3157 +lemon MACH_LEMON LEMON 3158 +csc MACH_CSC CSC 3159 +gira_knxip_router MACH_GIRA_KNXIP_ROUTER GIRA_KNXIP_ROUTER 3160 +t20 MACH_T20 T20 3161 +hdmini MACH_HDMINI HDMINI 3162 +sciphone_g2 MACH_SCIPHONE_G2 SCIPHONE_G2 3163 +express MACH_EXPRESS EXPRESS 3164 +express_kt MACH_EXPRESS_KT EXPRESS_KT 3165 +maximasp MACH_MAXIMASP MAXIMASP 3166 +nitrogen_imx51 MACH_NITROGEN_IMX51 NITROGEN_IMX51 3167 +nitrogen_imx53 MACH_NITROGEN_IMX53 NITROGEN_IMX53 3168 +sunfire MACH_SUNFIRE SUNFIRE 3169 +arowana MACH_AROWANA AROWANA 3170 +tegra_daytona MACH_TEGRA_DAYTONA TEGRA_DAYTONA 3171 +tegra_swordfish MACH_TEGRA_SWORDFISH TEGRA_SWORDFISH 3172 +edison MACH_EDISON EDISON 3173 +svp8500v1 MACH_SVP8500V1 SVP8500V1 3174 +svp8500v2 MACH_SVP8500V2 SVP8500V2 3175 +svp5500 MACH_SVP5500 SVP5500 3176 +b5500 MACH_B5500 B5500 3177 +s5500 MACH_S5500 S5500 3178 +icon MACH_ICON ICON 3179 +elephant MACH_ELEPHANT ELEPHANT 3180 +msm8x60_fusion MACH_MSM8X60_FUSION MSM8X60_FUSION 3181 +shooter MACH_SHOOTER SHOOTER 3182 +spade_lte MACH_SPADE_LTE SPADE_LTE 3183 +philhwani MACH_PHILHWANI PHILHWANI 3184 +gsncomm MACH_GSNCOMM GSNCOMM 3185 +strasbourg_a2 MACH_STRASBOURG_A2 STRASBOURG_A2 3186 +mmm MACH_MMM MMM 3187 +davinci_dm365_bv MACH_DAVINCI_DM365_BV DAVINCI_DM365_BV 3188 +ag5evm MACH_AG5EVM AG5EVM 3189 +sc575plc MACH_SC575PLC SC575PLC 3190 +sc575hmi MACH_SC575IPC SC575IPC 3191 +omap3_tdm3730 MACH_OMAP3_TDM3730 OMAP3_TDM3730 3192 +g7 MACH_G7 G7 3193 +top9000_eval MACH_TOP9000_EVAL TOP9000_EVAL 3194 +top9000_su MACH_TOP9000_SU TOP9000_SU 3195 +utm300 MACH_UTM300 UTM300 3196 +tsunagi MACH_TSUNAGI TSUNAGI 3197 +ts75xx MACH_TS75XX TS75XX 3198 +msm8x60_fusn_ffa MACH_MSM8X60_FUSN_FFA MSM8X60_FUSN_FFA 3199 +ts47xx MACH_TS47XX TS47XX 3200 +da850_k5 MACH_DA850_K5 DA850_K5 3201 +ax502 MACH_AX502 AX502 3202 +igep0032 MACH_IGEP0032 IGEP0032 3203 +antero MACH_ANTERO ANTERO 3204 +synergy MACH_SYNERGY SYNERGY 3205 +ics_if_voip MACH_ICS_IF_VOIP ICS_IF_VOIP 3206 +wlf_cragg_6410 MACH_WLF_CRAGG_6410 WLF_CRAGG_6410 3207 +punica MACH_PUNICA PUNICA 3208 +sbc_nt250 MACH_SBC_NT250 SBC_NT250 3209 +mx27_wmultra MACH_MX27_WMULTRA MX27_WMULTRA 3210 +mackerel MACH_MACKEREL MACKEREL 3211 +fa9x27 MACH_FA9X27 FA9X27 3213 +ns2816tb MACH_NS2816TB NS2816TB 3214 +ns2816_ntpad MACH_NS2816_NTPAD NS2816_NTPAD 3215 +ns2816_ntnb MACH_NS2816_NTNB NS2816_NTNB 3216 +kaen MACH_KAEN KAEN 3217 +nv1000 MACH_NV1000 NV1000 3218 +nuc950ts MACH_NUC950TS NUC950TS 3219 +nokia_rm680 MACH_NOKIA_RM680 NOKIA_RM680 3220 +ast2200 MACH_AST2200 AST2200 3221 +lead MACH_LEAD LEAD 3222 +unino1 MACH_UNINO1 UNINO1 3223 +greeco MACH_GREECO GREECO 3224 +verdi MACH_VERDI VERDI 3225 +dm6446_adbox MACH_DM6446_ADBOX DM6446_ADBOX 3226 +quad_salsa MACH_QUAD_SALSA QUAD_SALSA 3227 +abb_gma_1_1 MACH_ABB_GMA_1_1 ABB_GMA_1_1 3228 +svcid MACH_SVCID SVCID 3229 +msm8960_sim MACH_MSM8960_SIM MSM8960_SIM 3230 +msm8960_rumi3 MACH_MSM8960_RUMI3 MSM8960_RUMI3 3231 +icon_g MACH_ICON_G ICON_G 3232 +mb3 MACH_MB3 MB3 3233 +gsia18s MACH_GSIA18S GSIA18S 3234 +pivicc MACH_PIVICC PIVICC 3235 +pcm048 MACH_PCM048 PCM048 3236 +dds MACH_DDS DDS 3237 +chalten_xa1 MACH_CHALTEN_XA1 CHALTEN_XA1 3238 |