diff options
Diffstat (limited to 'arch/arm')
| -rw-r--r-- | arch/arm/boot/dts/integratorap.dts | 41 | ||||
| -rw-r--r-- | arch/arm/include/asm/hardware/pci_v3.h | 186 | ||||
| -rw-r--r-- | arch/arm/include/asm/mach/pci.h | 17 | ||||
| -rw-r--r-- | arch/arm/kernel/bios32.c | 9 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/Makefile | 2 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/include/mach/platform.h | 23 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/integrator_ap.c | 31 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/pci.c | 113 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/pci_v3.c | 532 | ||||
| -rw-r--r-- | arch/arm/mach-integrator/pci_v3.h | 2 |
10 files changed, 550 insertions, 406 deletions
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/integratorap.dts index c9c3fa34464..03f23b7a0ab 100644 --- a/arch/arm/boot/dts/integratorap.dts +++ b/arch/arm/boot/dts/integratorap.dts @@ -39,6 +39,47 @@ valid-mask = <0x003fffff>; }; + pci: pciv3@62000000 { + compatible = "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + ranges = <0x00000000 0 0x61000000 /* config space */ + 0x61000000 0 0x00100000 /* 16 MiB @ 61000000 */ + 0x01000000 0 0x60000000 /* I/O space */ + 0x60000000 0 0x00100000 /* 16 MiB @ 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory */ + 0x40000000 0 0x10000000 /* 256 MiB @ 40000000 */ + 0x42000000 0 0x50000000 /* prefetchable memory */ + 0x50000000 0 0x10000000>; /* 256 MiB @ 50000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; + }; + fpga { /* * The Integator/AP predates the idea to have magic numbers diff --git a/arch/arm/include/asm/hardware/pci_v3.h b/arch/arm/include/asm/hardware/pci_v3.h deleted file mode 100644 index 2811c7e2cfd..00000000000 --- a/arch/arm/include/asm/hardware/pci_v3.h +++ /dev/null @@ -1,186 +0,0 @@ -/* - * arch/arm/include/asm/hardware/pci_v3.h - * - * Internal header file PCI V3 chip - * - * Copyright (C) ARM Limited - * Copyright (C) 2000-2001 Deep Blue Solutions Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ -#ifndef ASM_ARM_HARDWARE_PCI_V3_H -#define ASM_ARM_HARDWARE_PCI_V3_H - -/* ------------------------------------------------------------------------------- - * V3 Local Bus to PCI Bridge definitions - * ------------------------------------------------------------------------------- - * Registers (these are taken from page 129 of the EPC User's Manual Rev 1.04 - * All V3 register names are prefaced by V3_ to avoid clashing with any other - * PCI definitions. Their names match the user's manual. - * - * I'm assuming that I20 is disabled. - * - */ -#define V3_PCI_VENDOR 0x00000000 -#define V3_PCI_DEVICE 0x00000002 -#define V3_PCI_CMD 0x00000004 -#define V3_PCI_STAT 0x00000006 -#define V3_PCI_CC_REV 0x00000008 -#define V3_PCI_HDR_CFG 0x0000000C -#define V3_PCI_IO_BASE 0x00000010 -#define V3_PCI_BASE0 0x00000014 -#define V3_PCI_BASE1 0x00000018 -#define V3_PCI_SUB_VENDOR 0x0000002C -#define V3_PCI_SUB_ID 0x0000002E -#define V3_PCI_ROM 0x00000030 -#define V3_PCI_BPARAM 0x0000003C -#define V3_PCI_MAP0 0x00000040 -#define V3_PCI_MAP1 0x00000044 -#define V3_PCI_INT_STAT 0x00000048 -#define V3_PCI_INT_CFG 0x0000004C -#define V3_LB_BASE0 0x00000054 -#define V3_LB_BASE1 0x00000058 -#define V3_LB_MAP0 0x0000005E -#define V3_LB_MAP1 0x00000062 -#define V3_LB_BASE2 0x00000064 -#define V3_LB_MAP2 0x00000066 -#define V3_LB_SIZE 0x00000068 -#define V3_LB_IO_BASE 0x0000006E -#define V3_FIFO_CFG 0x00000070 -#define V3_FIFO_PRIORITY 0x00000072 -#define V3_FIFO_STAT 0x00000074 -#define V3_LB_ISTAT 0x00000076 -#define V3_LB_IMASK 0x00000077 -#define V3_SYSTEM 0x00000078 -#define V3_LB_CFG 0x0000007A -#define V3_PCI_CFG 0x0000007C -#define V3_DMA_PCI_ADR0 0x00000080 -#define V3_DMA_PCI_ADR1 0x00000090 -#define V3_DMA_LOCAL_ADR0 0x00000084 -#define V3_DMA_LOCAL_ADR1 0x00000094 -#define V3_DMA_LENGTH0 0x00000088 -#define V3_DMA_LENGTH1 0x00000098 -#define V3_DMA_CSR0 0x0000008B -#define V3_DMA_CSR1 0x0000009B -#define V3_DMA_CTLB_ADR0 0x0000008C -#define V3_DMA_CTLB_ADR1 0x0000009C -#define V3_DMA_DELAY 0x000000E0 -#define V3_MAIL_DATA 0x000000C0 -#define V3_PCI_MAIL_IEWR 0x000000D0 -#define V3_PCI_MAIL_IERD 0x000000D2 -#define V3_LB_MAIL_IEWR 0x000000D4 -#define V3_LB_MAIL_IERD 0x000000D6 -#define V3_MAIL_WR_STAT 0x000000D8 -#define V3_MAIL_RD_STAT 0x000000DA -#define V3_QBA_MAP 0x000000DC - -/* PCI COMMAND REGISTER bits - */ -#define V3_COMMAND_M_FBB_EN (1 << 9) -#define V3_COMMAND_M_SERR_EN (1 << 8) -#define V3_COMMAND_M_PAR_EN (1 << 6) -#define V3_COMMAND_M_MASTER_EN (1 << 2) -#define V3_COMMAND_M_MEM_EN (1 << 1) -#define V3_COMMAND_M_IO_EN (1 << 0) - -/* SYSTEM REGISTER bits - */ -#define V3_SYSTEM_M_RST_OUT (1 << 15) -#define V3_SYSTEM_M_LOCK (1 << 14) - -/* PCI_CFG bits - */ -#define V3_PCI_CFG_M_I2O_EN (1 << 15) -#define V3_PCI_CFG_M_IO_REG_DIS (1 << 14) -#define V3_PCI_CFG_M_IO_DIS (1 << 13) -#define V3_PCI_CFG_M_EN3V (1 << 12) -#define V3_PCI_CFG_M_RETRY_EN (1 << 10) -#define V3_PCI_CFG_M_AD_LOW1 (1 << 9) -#define V3_PCI_CFG_M_AD_LOW0 (1 << 8) - -/* PCI_BASE register bits (PCI -> Local Bus) - */ -#define V3_PCI_BASE_M_ADR_BASE 0xFFF00000 -#define V3_PCI_BASE_M_ADR_BASEL 0x000FFF00 -#define V3_PCI_BASE_M_PREFETCH (1 << 3) -#define V3_PCI_BASE_M_TYPE (3 << 1) -#define V3_PCI_BASE_M_IO (1 << 0) - -/* PCI MAP register bits (PCI -> Local bus) - */ -#define V3_PCI_MAP_M_MAP_ADR 0xFFF00000 -#define V3_PCI_MAP_M_RD_POST_INH (1 << 15) -#define V3_PCI_MAP_M_ROM_SIZE (3 << 10) -#define V3_PCI_MAP_M_SWAP (3 << 8) -#define V3_PCI_MAP_M_ADR_SIZE 0x000000F0 -#define V3_PCI_MAP_M_REG_EN (1 << 1) -#define V3_PCI_MAP_M_ENABLE (1 << 0) - -/* - * LB_BASE0,1 register bits (Local bus -> PCI) - */ -#define V3_LB_BASE_ADR_BASE 0xfff00000 -#define V3_LB_BASE_SWAP (3 << 8) -#define V3_LB_BASE_ADR_SIZE (15 << 4) -#define V3_LB_BASE_PREFETCH (1 << 3) -#define V3_LB_BASE_ENABLE (1 << 0) - -#define V3_LB_BASE_ADR_SIZE_1MB (0 << 4) -#define V3_LB_BASE_ADR_SIZE_2MB (1 << 4) -#define V3_LB_BASE_ADR_SIZE_4MB (2 << 4) -#define V3_LB_BASE_ADR_SIZE_8MB (3 << 4) -#define V3_LB_BASE_ADR_SIZE_16MB (4 << 4) -#define V3_LB_BASE_ADR_SIZE_32MB (5 << 4) -#define V3_LB_BASE_ADR_SIZE_64MB (6 << 4) -#define V3_LB_BASE_ADR_SIZE_128MB (7 << 4) -#define V3_LB_BASE_ADR_SIZE_256MB (8 << 4) -#define V3_LB_BASE_ADR_SIZE_512MB (9 << 4) -#define V3_LB_BASE_ADR_SIZE_1GB (10 << 4) -#define V3_LB_BASE_ADR_SIZE_2GB (11 << 4) - -#define v3_addr_to_lb_base(a) ((a) & V3_LB_BASE_ADR_BASE) - -/* - * LB_MAP0,1 register bits (Local bus -> PCI) - */ -#define V3_LB_MAP_MAP_ADR 0xfff0 -#define V3_LB_MAP_TYPE (7 << 1) -#define V3_LB_MAP_AD_LOW_EN (1 << 0) - -#define V3_LB_MAP_TYPE_IACK (0 << 1) -#define V3_LB_MAP_TYPE_IO (1 << 1) -#define V3_LB_MAP_TYPE_MEM (3 << 1) -#define V3_LB_MAP_TYPE_CONFIG (5 << 1) -#define V3_LB_MAP_TYPE_MEM_MULTIPLE (6 << 1) - -#define v3_addr_to_lb_map(a) (((a) >> 16) & V3_LB_MAP_MAP_ADR) - -/* - * LB_BASE2 register bits (Local bus -> PCI IO) - */ -#define V3_LB_BASE2_ADR_BASE 0xff00 -#define V3_LB_BASE2_SWAP (3 << 6) -#define V3_LB_BASE2_ENABLE (1 << 0) - -#define v3_addr_to_lb_base2(a) (((a) >> 16) & V3_LB_BASE2_ADR_BASE) - -/* - * LB_MAP2 register bits (Local bus -> PCI IO) - */ -#define V3_LB_MAP2_MAP_ADR 0xff00 - -#define v3_addr_to_lb_map2(a) (((a) >> 16) & V3_LB_MAP2_MAP_ADR) - -#endif diff --git a/arch/arm/include/asm/mach/pci.h b/arch/arm/include/asm/mach/pci.h index 7d2c3c84380..a1c90d7feb0 100644 --- a/arch/arm/include/asm/mach/pci.h +++ b/arch/arm/include/asm/mach/pci.h @@ -16,6 +16,7 @@ struct pci_sys_data; struct pci_ops; struct pci_bus; +struct device; struct hw_pci { #ifdef CONFIG_PCI_DOMAINS @@ -68,7 +69,16 @@ struct pci_sys_data { /* * Call this with your hw_pci struct to initialise the PCI system. */ -void pci_common_init(struct hw_pci *); +void pci_common_init_dev(struct device *, struct hw_pci *); + +/* + * Compatibility wrapper for older platforms that do not care about + * passing the parent device. + */ +static inline void pci_common_init(struct hw_pci *hw) +{ + pci_common_init_dev(NULL, hw); +} /* * Setup early fixed I/O mapping. @@ -96,9 +106,4 @@ extern struct pci_ops via82c505_ops; extern int via82c505_setup(int nr, struct pci_sys_data *); extern void via82c505_init(void *sysdata); -extern struct pci_ops pci_v3_ops; -extern int pci_v3_setup(int nr, struct pci_sys_data *); -extern void pci_v3_preinit(void); -extern void pci_v3_postinit(void); - #endif /* __ASM_MACH_PCI_H */ diff --git a/arch/arm/kernel/bios32.c b/arch/arm/kernel/bios32.c index b2ed73c4548..261fcc82616 100644 --- a/arch/arm/kernel/bios32.c +++ b/arch/arm/kernel/bios32.c @@ -445,7 +445,8 @@ static int pcibios_init_resources(int busnr, struct pci_sys_data *sys) return 0; } -static void pcibios_init_hw(struct hw_pci *hw, struct list_head *head) +static void pcibios_init_hw(struct device *parent, struct hw_pci *hw, + struct list_head *head) { struct pci_sys_data *sys = NULL; int ret; @@ -480,7 +481,7 @@ static void pcibios_init_hw(struct hw_pci *hw, struct list_head *head) if (hw->scan) sys->bus = hw->scan(nr, sys); else - sys->bus = pci_scan_root_bus(NULL, sys->busnr, + sys->bus = pci_scan_root_bus(parent, sys->busnr, hw->ops, sys, &sys->resources); if (!sys->bus) @@ -497,7 +498,7 @@ static void pcibios_init_hw(struct hw_pci *hw, struct list_head *head) } } -void pci_common_init(struct hw_pci *hw) +void pci_common_init_dev(struct device *parent, struct hw_pci *hw) { struct pci_sys_data *sys; LIST_HEAD(head); @@ -505,7 +506,7 @@ void pci_common_init(struct hw_pci *hw) pci_add_flags(PCI_REASSIGN_ALL_RSRC); if (hw->preinit) hw->preinit(); - pcibios_init_hw(hw, &head); + pcibios_init_hw(parent, hw, &head); if (hw->postinit) hw->postinit(); diff --git a/arch/arm/mach-integrator/Makefile b/arch/arm/mach-integrator/Makefile index d14d6b76f4c..ec759ded7b6 100644 --- a/arch/arm/mach-integrator/Makefile +++ b/arch/arm/mach-integrator/Makefile @@ -8,5 +8,5 @@ obj-y := core.o lm.o leds.o obj-$(CONFIG_ARCH_INTEGRATOR_AP) += integrator_ap.o obj-$(CONFIG_ARCH_INTEGRATOR_CP) += integrator_cp.o -obj-$(CONFIG_PCI) += pci_v3.o pci.o +obj-$(CONFIG_PCI) += pci_v3.o obj-$(CONFIG_INTEGRATOR_IMPD1) += impd1.o diff --git a/arch/arm/mach-integrator/include/mach/platform.h b/arch/arm/mach-integrator/include/mach/platform.h index be5859efe10..306d025d973 100644 --- a/arch/arm/mach-integrator/include/mach/platform.h +++ b/arch/arm/mach-integrator/include/mach/platform.h @@ -305,29 +305,6 @@ /* KMI definitions are now in include/asm-arm/hardware/amba_kmi.h -- rmk */ /* ------------------------------------------------------------------------ - * Where in the memory map does PCI live? - * ------------------------------------------------------------------------ - * This represents a fairly liberal usage of address space. Even though - * the V3 only has two windows (therefore we need to map stuff on the fly), - * we maintain the same addresses, even if they're not mapped. - * - */ -#define PHYS_PCI_MEM_BASE 0x40000000 /* 512M to xxx */ -/* unused 256M from A0000000-AFFFFFFF might be used for I2O ??? - */ -#define PHYS_PCI_IO_BASE 0x60000000 /* 16M to xxx */ -/* unused (128-16)M from B1000000-B7FFFFFF - */ -#define PHYS_PCI_CONFIG_BASE 0x61000000 /* 16M to xxx */ -/* unused ((128-16)M - 64K) from XXX - */ -#define PHYS_PCI_V3_BASE 0x62000000 - -#define PCI_MEMORY_VADDR IOMEM(0xe8000000) -#define PCI_CONFIG_VADDR IOMEM(0xec000000) -#define PCI_V3_VADDR IOMEM(0xed000000) - -/* ------------------------------------------------------------------------ * Integrator Interrupt Controllers * ------------------------------------------------------------------------ * diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c index b23c8e4f28e..a5b15c4e8de 100644 --- a/arch/arm/mach-integrator/integrator_ap.c +++ b/arch/arm/mach-integrator/integrator_ap.c @@ -41,7 +41,6 @@ #include <linux/stat.h> #include <linux/sys_soc.h> #include <linux/termios.h> -#include <video/vga.h> #include <mach/hardware.h> #include <mach/platform.h> @@ -57,10 +56,10 @@ #include <asm/mach/arch.h> #include <asm/mach/irq.h> #include <asm/mach/map.h> -#include <asm/mach/pci.h> #include <asm/mach/time.h> #include "common.h" +#include "pci_v3.h" /* Base address to the AP system controller */ void __iomem *ap_syscon_base; @@ -78,10 +77,6 @@ void __iomem *ap_syscon_base; /* * Logical Physical - * e8000000 40000000 PCI memory PHYS_PCI_MEM_BASE (max 512M) - * ec000000 61000000 PCI config space PHYS_PCI_CONFIG_BASE (max 16M) - * ed000000 62000000 PCI V3 regs PHYS_PCI_V3_BASE (max 64k) - * fee00000 60000000 PCI IO PHYS_PCI_IO_BASE (max 16M) * ef000000 Cache flush * f1000000 10000000 Core module registers * f1100000 11000000 System controller registers @@ -130,29 +125,13 @@ static struct map_desc ap_io_desc[] __initdata __maybe_unused = { .pfn = __phys_to_pfn(INTEGRATOR_AP_GPIO_BASE), .length = SZ_4K, .type = MT_DEVICE - }, { - .virtual = (unsigned long)PCI_MEMORY_VADDR, - .pfn = __phys_to_pfn(PHYS_PCI_MEM_BASE), - .length = SZ_16M, - .type = MT_DEVICE - }, { - .virtual = (unsigned long)PCI_CONFIG_VADDR, - .pfn = __phys_to_pfn(PHYS_PCI_CONFIG_BASE), - .length = SZ_16M, - .type = MT_DEVICE - }, { - .virtual = (unsigned long)PCI_V3_VADDR, - .pfn = __phys_to_pfn(PHYS_PCI_V3_BASE), - .length = SZ_64K, - .type = MT_DEVICE } }; static void __init ap_map_io(void) { iotable_init(ap_io_desc, ARRAY_SIZE(ap_io_desc)); - vga_base = (unsigned long)PCI_MEMORY_VADDR; - pci_map_io_early(__phys_to_pfn(PHYS_PCI_IO_BASE)); + pci_v3_early_init(); } #ifdef CONFIG_PM @@ -615,6 +594,11 @@ static void __init ap_map_io_atag(void) * for eventual deletion. */ +static struct platform_device pci_v3_device = { + .name = "pci-v3", + .id = 0, +}; + static struct resource cfi_flash_resource = { .start = INTEGRATOR_FLASH_BASE, .end = INTEGRATOR_FLASH_BASE + INTEGRATOR_FLASH_SIZE - 1, @@ -672,6 +656,7 @@ static void __init ap_init(void) unsigned long sc_dec; int i; + platform_device_register(&pci_v3_device); platform_device_register(&cfi_flash_device); ap_syscon_base = __io_address(INTEGRATOR_SC_BASE); diff --git a/arch/arm/mach-integrator/pci.c b/arch/arm/mach-integrator/pci.c deleted file mode 100644 index 6c1667e728f..00000000000 --- a/arch/arm/mach-integrator/pci.c +++ /dev/null @@ -1,113 +0,0 @@ -/* - * linux/arch/arm/mach-integrator/pci-integrator.c - * - * Copyright (C) 1999 ARM Limited - * Copyright (C) 2000 Deep Blue Solutions Ltd - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - * - * - * PCI functions for Integrator - */ -#include <linux/kernel.h> -#include <linux/pci.h> -#include <linux/interrupt.h> -#include <linux/init.h> - -#include <asm/mach/pci.h> -#include <asm/mach-types.h> - -#include <mach/irqs.h> - -/* - * A small note about bridges and interrupts. The DECchip 21050 (and - * later) adheres to the PCI-PCI bridge specification. This says that - * the interrupts on the other side of a bridge are swizzled in the - * following manner: - * - * Dev Interrupt Interrupt - * Pin on Pin on - * Device Connector - * - * 4 A A - * B B - * C C - * D D - * - * 5 A B - * B C - * C D - * D A - * - * 6 A C - * B D - * C A - * D B - * - * 7 A D - * B A - * C B - * D C - * - * Where A = pin 1, B = pin 2 and so on and pin=0 = default = A. - * Thus, each swizzle is ((pin-1) + (device#-4)) % 4 - */ - -/* - * This routine handles multiple bridges. - */ -static u8 __init integrator_swizzle(struct pci_dev *dev, u8 *pinp) -{ - if (*pinp == 0) - *pinp = 1; - - return pci_common_swizzle(dev, pinp); -} - -static int irq_tab[4] __initdata = { - IRQ_AP_PCIINT0, IRQ_AP_PCIINT1, IRQ_AP_PCIINT2, IRQ_AP_PCIINT3 -}; - -/* - * map the specified device/slot/pin to an IRQ. This works out such - * that slot 9 pin 1 is INT0, pin 2 is INT1, and slot 10 pin 1 is INT1. - */ -static int __init integrator_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) -{ - int intnr = ((slot - 9) + (pin - 1)) & 3; - - return irq_tab[intnr]; -} - -extern void pci_v3_init(void *); - -static struct hw_pci integrator_pci __initdata = { - .swizzle = integrator_swizzle, - .map_irq = integrator_map_irq, - .setup = pci_v3_setup, - .nr_controllers = 1, - .ops = &pci_v3_ops, - .preinit = pci_v3_preinit, - .postinit = pci_v3_postinit, -}; - -static int __init integrator_pci_init(void) -{ - if (machine_is_integrator()) - pci_common_init(&integrator_pci); - return 0; -} - -subsys_initcall(integrator_pci_init); diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c index e7fcea7f330..a0e069d37e1 100644 --- a/arch/arm/mach-integrator/pci_v3.c +++ b/arch/arm/mach-integrator/pci_v3.c @@ -27,16 +27,198 @@ #include <linux/spinlock.h> #include <linux/init.h> #include <linux/io.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> +#include <video/vga.h> #include <mach/hardware.h> #include <mach/platform.h> #include <mach/irqs.h> +#include <asm/mach/map.h> #include <asm/signal.h> #include <asm/mach/pci.h> #include <asm/irq_regs.h> -#include <asm/hardware/pci_v3.h> +#include "pci_v3.h" + +/* + * Where in the memory map does PCI live? + * + * This represents a fairly liberal usage of address space. Even though + * the V3 only has two windows (therefore we need to map stuff on the fly), + * we maintain the same addresses, even if they're not mapped. + */ +#define PHYS_PCI_MEM_BASE 0x40000000 /* 512M */ +#define PHYS_PCI_IO_BASE 0x60000000 /* 16M */ +#define PHYS_PCI_CONFIG_BASE 0x61000000 /* 16M */ +#define PHYS_PCI_V3_BASE 0x62000000 /* 64K */ + +#define PCI_MEMORY_VADDR IOMEM(0xe8000000) +#define PCI_CONFIG_VADDR IOMEM(0xec000000) + +/* + * V3 Local Bus to PCI Bridge definitions + * + * Registers (these are taken from page 129 of the EPC User's Manual Rev 1.04 + * All V3 register names are prefaced by V3_ to avoid clashing with any other + * PCI definitions. Their names match the user's manual. + * + * I'm assuming that I20 is disabled. + * + */ +#define V3_PCI_VENDOR 0x00000000 +#define V3_PCI_DEVICE 0x00000002 +#define V3_PCI_CMD 0x00000004 +#define V3_PCI_STAT 0x00000006 +#define V3_PCI_CC_REV 0x00000008 +#define V3_PCI_HDR_CFG 0x0000000C +#define V3_PCI_IO_BASE 0x00000010 +#define V3_PCI_BASE0 0x00000014 +#define V3_PCI_BASE1 0x00000018 +#define V3_PCI_SUB_VENDOR 0x0000002C +#define V3_PCI_SUB_ID 0x0000002E +#define V3_PCI_ROM 0x00000030 +#define V3_PCI_BPARAM 0x0000003C +#define V3_PCI_MAP0 0x00000040 +#define V3_PCI_MAP1 0x00000044 +#define V3_PCI_INT_STAT 0x00000048 +#define V3_PCI_INT_CFG 0x0000004C +#define V3_LB_BASE0 0x00000054 +#define V3_LB_BASE1 0x00000058 +#define V3_LB_MAP0 0x0000005E +#define V3_LB_MAP1 0x00000062 +#define V3_LB_BASE2 0x00000064 +#define V3_LB_MAP2 0x00000066 +#define V3_LB_SIZE 0x00000068 +#define V3_LB_IO_BASE 0x0000006E +#define V3_FIFO_CFG 0x00000070 +#define V3_FIFO_PRIORITY 0x00000072 +#define V3_FIFO_STAT 0x00000074 +#define V3_LB_ISTAT 0x00000076 +#define V3_LB_IMASK 0x00000077 +#define V3_SYSTEM 0x00000078 +#define V3_LB_CFG 0x0000007A +#define V3_PCI_CFG 0x0000007C +#define V3_DMA_PCI_ADR0 0x00000080 +#define V3_DMA_PCI_ADR1 0x00000090 +#define V3_DMA_LOCAL_ADR0 0x00000084 +#define V3_DMA_LOCAL_ADR1 0x00000094 +#define V3_DMA_LENGTH0 0x00000088 +#define V3_DMA_LENGTH1 0x00000098 +#define V3_DMA_CSR0 0x0000008B +#define V3_DMA_CSR1 0x0000009B +#define V3_DMA_CTLB_ADR0 0x0000008C +#define V3_DMA_CTLB_ADR1 0x0000009C +#define V3_DMA_DELAY 0x000000E0 +#define V3_MAIL_DATA 0x000000C0 +#define V3_PCI_MAIL_IEWR 0x000000D0 +#define V3_PCI_MAIL_IERD 0x000000D2 +#define V3_LB_MAIL_IEWR 0x000000D4 +#define V3_LB_MAIL_IERD 0x000000D6 +#define V3_MAIL_WR_STAT 0x000000D8 +#define V3_MAIL_RD_STAT 0x000000DA +#define V3_QBA_MAP 0x000000DC + +/* PCI COMMAND REGISTER bits + */ +#define V3_COMMAND_M_FBB_EN (1 << 9) +#define V3_COMMAND_M_SERR_EN (1 << 8) +#define V3_COMMAND_M_PAR_EN (1 << 6) +#define V3_COMMAND_M_MASTER_EN (1 << 2) +#define V3_COMMAND_M_MEM_EN (1 << 1) +#define V3_COMMAND_M_IO_EN (1 << 0) + +/* SYSTEM REGISTER bits + */ +#define V3_SYSTEM_M_RST_OUT (1 << 15) +#define V3_SYSTEM_M_LOCK (1 << 14) + +/* PCI_CFG bits + */ +#define V3_PCI_CFG_M_I2O_EN (1 << 15) +#define V3_PCI_CFG_M_IO_REG_DIS (1 << 14) +#define V3_PCI_CFG_M_IO_DIS (1 << 13) +#define V3_PCI_CFG_M_EN3V (1 << 12) +#define V3_PCI_CFG_M_RETRY_EN (1 << 10) +#define V3_PCI_CFG_M_AD_LOW1 (1 << 9) +#define V3_PCI_CFG_M_AD_LOW0 (1 << 8) + +/* PCI_BASE register bits (PCI -> Local Bus) + */ +#define V3_PCI_BASE_M_ADR_BASE 0xFFF00000 +#define V3_PCI_BASE_M_ADR_BASEL 0x000FFF00 +#define V3_PCI_BASE_M_PREFETCH (1 << 3) +#define V3_PCI_BASE_M_TYPE (3 << 1) +#define V3_PCI_BASE_M_IO (1 << 0) + +/* PCI MAP register bits (PCI -> Local bus) + */ +#define V3_PCI_MAP_M_MAP_ADR 0xFFF00000 +#define V3_PCI_MAP_M_RD_POST_INH (1 << 15) +#define V3_PCI_MAP_M_ROM_SIZE (3 << 10) +#define V3_PCI_MAP_M_SWAP (3 << 8) +#define V3_PCI_MAP_M_ADR_SIZE 0x000000F0 +#define V3_PCI_MAP_M_REG_EN (1 << 1) +#define V3_PCI_MAP_M_ENABLE (1 << 0) + +/* + * LB_BASE0,1 register bits (Local bus -> PCI) + */ +#define V3_LB_BASE_ADR_BASE 0xfff00000 +#define V3_LB_BASE_SWAP (3 << 8) +#define V3_LB_BASE_ADR_SIZE (15 << 4) +#define V3_LB_BASE_PREFETCH (1 << 3) +#define V3_LB_BASE_ENABLE (1 << 0) + +#define V3_LB_BASE_ADR_SIZE_1MB (0 << 4) +#define V3_LB_BASE_ADR_SIZE_2MB (1 << 4) +#define V3_LB_BASE_ADR_SIZE_4MB (2 << 4) +#define V3_LB_BASE_ADR_SIZE_8MB (3 << 4) +#define V3_LB_BASE_ADR_SIZE_16MB (4 << 4) +#define V3_LB_BASE_ADR_SIZE_32MB (5 << 4) +#define V3_LB_BASE_ADR_SIZE_64MB (6 << 4) +#define V3_LB_BASE_ADR_SIZE_128MB (7 << 4) +#define V3_LB_BASE_ADR_SIZE_256MB (8 << 4) +#define V3_LB_BASE_ADR_SIZE_512MB (9 << 4) +#define V3_LB_BASE_ADR_SIZE_1GB (10 << 4) +#define V3_LB_BASE_ADR_SIZE_2GB (11 << 4) + +#define v3_addr_to_lb_base(a) ((a) & V3_LB_BASE_ADR_BASE) + +/* + * LB_MAP0,1 register bits (Local bus -> PCI) + */ +#define V3_LB_MAP_MAP_ADR 0xfff0 +#define V3_LB_MAP_TYPE (7 << 1) +#define V3_LB_MAP_AD_LOW_EN (1 << 0) + +#define V3_LB_MAP_TYPE_IACK (0 << 1) +#define V3_LB_MAP_TYPE_IO (1 << 1) +#define V3_LB_MAP_TYPE_MEM (3 << 1) +#define V3_LB_MAP_TYPE_CONFIG (5 << 1) +#define V3_LB_MAP_TYPE_MEM_MULTIPLE (6 << 1) + +#define v3_addr_to_lb_map(a) (((a) >> 16) & V3_LB_MAP_MAP_ADR) + +/* + * LB_BASE2 register bits (Local bus -> PCI IO) + */ +#define V3_LB_BASE2_ADR_BASE 0xff00 +#define V3_LB_BASE2_SWAP (3 << 6) +#define V3_LB_BASE2_ENABLE (1 << 0) + +#define v3_addr_to_lb_base2(a) (((a) >> 16) & V3_LB_BASE2_ADR_BASE) + +/* + * LB_MAP2 register bits (Local bus -> PCI IO) + */ +#define V3_LB_MAP2_MAP_ADR 0xff00 + +#define v3_addr_to_lb_map2(a) (((a) >> 16) & V3_LB_MAP2_MAP_ADR) /* * The V3 PCI interface chip in Integrator provides several windows from @@ -101,15 +283,22 @@ * the mappings into PCI memory. */ +/* Filled in by probe */ +static void __iomem *pci_v3_base; +static struct resource conf_mem; /* FIXME: remap this instead of static map */ +static struct resource io_mem; +static struct resource non_mem; +static struct resource pre_mem; + // V3 access routines -#define v3_writeb(o,v) __raw_writeb(v, PCI_V3_VADDR + (unsigned int)(o)) -#define v3_readb(o) (__raw_readb(PCI_V3_VADDR + (unsigned int)(o))) +#define v3_writeb(o,v) __raw_writeb(v, pci_v3_base + (unsigned int)(o)) +#define v3_readb(o) (__raw_readb(pci_v3_base + (unsigned int)(o))) -#define v3_writew(o,v) __raw_writew(v, PCI_V3_VADDR + (unsigned int)(o)) -#define v3_readw(o) (__raw_readw(PCI_V3_VADDR + (unsigned int)(o))) +#define v3_writew(o,v) __raw_writew(v, pci_v3_base + (unsigned int)(o)) +#define v3_readw(o) (__raw_readw(pci_v3_base + (unsigned int)(o))) -#define v3_writel(o,v) __raw_writel(v, PCI_V3_VADDR + (unsigned int)(o)) -#define v3_readl(o) (__raw_readl(PCI_V3_VADDR + (unsigned int)(o))) +#define v3_writel(o,v) __raw_writel(v, pci_v3_base + (unsigned int)(o)) +#define v3_readl(o) (__raw_readl(pci_v3_base + (unsigned int)(o))) /*============================================================================ * @@ -243,13 +432,13 @@ static void __iomem *v3_open_config_window(struct pci_bus *bus, * prefetchable), this frees up base1 for re-use by * configuration memory */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE); /* * Set up base1/map1 to point into configuration space. */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_CONFIG_BASE) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(conf_mem.start) | V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, mapaddress); @@ -261,7 +450,7 @@ static void v3_close_config_window(void) /* * Reassign base1 for use by prefetchable PCI memory */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(pre_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | @@ -270,7 +459,7 @@ static void v3_close_config_window(void) /* * And shrink base0 back to a 256M window (NOTE: MAP0 already correct) */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); } @@ -337,25 +526,11 @@ static int v3_write_config(struct pci_bus *bus, unsigned int devfn, int where, return PCIBIOS_SUCCESSFUL; } -struct pci_ops pci_v3_ops = { +static struct pci_ops pci_v3_ops = { .read = v3_read_config, .write = v3_write_config, }; -static struct resource non_mem = { - .name = "PCI non-prefetchable", - .start = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START, - .end = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START + PCI_BUS_NONMEM_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct resource pre_mem = { - .name = "PCI prefetchable", - .start = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START, - .end = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START + PCI_BUS_PREMEM_SIZE - 1, - .flags = IORESOURCE_MEM | IORESOURCE_PREFETCH, -}; - static int __init pci_v3_setup_resources(struct pci_sys_data *sys) { if (request_resource(&iomem_resource, &non_mem)) { @@ -471,7 +646,7 @@ static irqreturn_t v3_irq(int dummy, void *devid) return IRQ_HANDLED; } -int __init pci_v3_setup(int nr, struct pci_sys_data *sys) +static int __init pci_v3_setup(int nr, struct pci_sys_data *sys) { int ret = 0; @@ -479,7 +654,7 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys) return -EINVAL; if (nr == 0) { - sys->mem_offset = PHYS_PCI_MEM_BASE; + sys->mem_offset = non_mem.start; ret = pci_v3_setup_resources(sys); } @@ -490,18 +665,10 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys) * V3_LB_BASE? - local bus address * V3_LB_MAP? - pci bus address */ -void __init pci_v3_preinit(void) +static void __init pci_v3_preinit(void) { unsigned long flags; unsigned int temp; - int ret; - - /* Remap the Integrator system controller */ - ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100); - if (!ap_syscon_base) { - pr_err("unable to remap the AP syscon for PCIv3\n"); - return; - } pcibios_min_mem = 0x00100000; @@ -525,7 +692,7 @@ void __init pci_v3_preinit(void) * Setup window 0 - PCI non-prefetchable memory * Local: 0x40000000 Bus: 0x00000000 Size: 256MB */ - v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE) | + v3_writel(V3_LB_BASE0, v3_addr_to_lb_base(non_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP0, v3_addr_to_lb_map(PCI_BUS_NONMEM_START) | V3_LB_MAP_TYPE_MEM); @@ -534,7 +701,7 @@ void __init pci_v3_preinit(void) * Setup window 1 - PCI prefetchable memory * Local: 0x50000000 Bus: 0x10000000 Size: 256MB */ - v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE + SZ_256M) | + v3_writel(V3_LB_BASE1, v3_addr_to_lb_base(pre_mem.start) | V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP1, v3_addr_to_lb_map(PCI_BUS_PREMEM_START) | @@ -543,7 +710,7 @@ void __init pci_v3_preinit(void) /* * Setup window 2 - PCI IO */ - v3_writel(V3_LB_BASE2, v3_addr_to_lb_base2(PHYS_PCI_IO_BASE) | + v3_writel(V3_LB_BASE2, v3_addr_to_lb_base2(io_mem.start) | V3_LB_BASE_ENABLE); v3_writew(V3_LB_MAP2, v3_addr_to_lb_map2(0)); @@ -578,18 +745,10 @@ void __init pci_v3_preinit(void) v3_writeb(V3_LB_IMASK, 0x28); __raw_writel(3, ap_syscon_base + INTEGRATOR_SC_PCIENABLE_OFFSET); - /* - * Grab the PCI error interrupt. - */ - ret = request_irq(IRQ_AP_V3INT, v3_irq, 0, "V3", NULL); - if (ret) - printk(KERN_ERR "PCI: unable to grab PCI error " - "interrupt: %d\n", ret); - raw_spin_unlock_irqrestore(&v3_lock, flags); } -void __init pci_v3_postinit(void) +static void __init pci_v3_postinit(void) { unsigned int pci_cmd; @@ -608,5 +767,278 @@ void __init pci_v3_postinit(void) "interrupt: %d\n", ret); #endif - register_isa_ports(PHYS_PCI_MEM_BASE, PHYS_PCI_IO_BASE, 0); + register_isa_ports(non_mem.start, io_mem.start, 0); +} + +/* + * A small note about bridges and interrupts. The DECchip 21050 (and + * later) adheres to the PCI-PCI bridge specification. This says that + * the interrupts on the other side of a bridge are swizzled in the + * following manner: + * + * Dev Interrupt Interrupt + * Pin on Pin on + * Device Connector + * + * 4 A A + * B B + * C C + * D D + * + * 5 A B + * B C + * C D + * D A + * + * 6 A C + * B D + * C A + * D B + * + * 7 A D + * B A + * C B + * D C + * + * Where A = pin 1, B = pin 2 and so on and pin=0 = default = A. + * Thus, each swizzle is ((pin-1) + (device#-4)) % 4 + */ + +/* + * This routine handles multiple bridges. + */ +static u8 __init pci_v3_swizzle(struct pci_dev *dev, u8 *pinp) +{ + if (*pinp == 0) + *pinp = 1; + + return pci_common_swizzle(dev, pinp); +} + +static int irq_tab[4] __initdata = { + IRQ_AP_PCIINT0, IRQ_AP_PCIINT1, IRQ_AP_PCIINT2, IRQ_AP_PCIINT3 +}; + +/* + * map the specified device/slot/pin to an IRQ. This works out such + * that slot 9 pin 1 is INT0, pin 2 is INT1, and slot 10 pin 1 is INT1. + */ +static int __init pci_v3_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + int intnr = ((slot - 9) + (pin - 1)) & 3; + + return irq_tab[intnr]; +} + +static struct hw_pci pci_v3 __initdata = { + .swizzle = pci_v3_swizzle, + .setup = pci_v3_setup, + .nr_controllers = 1, + .ops = &pci_v3_ops, + .preinit = pci_v3_preinit, + .postinit = pci_v3_postinit, +}; + +#ifdef CONFIG_OF + +static int __init pci_v3_map_irq_dt(const struct pci_dev *dev, u8 slot, u8 pin) +{ + struct of_irq oirq; + int ret; + + ret = of_irq_map_pci(dev, &oirq); + if (ret) { + dev_err(&dev->dev, "of_irq_map_pci() %d\n", ret); + /* Proper return code 0 == NO_IRQ */ + return 0; + } + + return irq_create_of_mapping(oirq.controller, oirq.specifier, + oirq.size); +} + +static int __init pci_v3_dtprobe(struct platform_device *pdev, + struct device_node *np) +{ + struct of_pci_range_parser parser; + struct of_pci_range range; + struct resource *res; + int irq, ret; + + if (of_pci_range_parser_init(&parser, np)) + return -EINVAL; + + /* Get base for bridge registers */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(&pdev->dev, "unable to obtain PCIv3 base\n"); + return -ENODEV; + } + pci_v3_base = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (!pci_v3_base) { + dev_err(&pdev->dev, "unable to remap PCIv3 base\n"); + return -ENODEV; + } + + /* Get and request error IRQ resource */ + irq = platform_get_irq(pdev, 0); + if (irq <= 0) { + dev_err(&pdev->dev, "unable to obtain PCIv3 error IRQ\n"); + return -ENODEV; + } + ret = devm_request_irq(&pdev->dev, irq, v3_irq, 0, + "PCIv3 error", NULL); + if (ret < 0) { + dev_err(&pdev->dev, "unable to request PCIv3 error IRQ %d (%d)\n", irq, ret); + return ret; + } + + for_each_of_pci_range(&parser, &range) { + if (!range.flags) { + of_pci_range_to_resource(&range, np, &conf_mem); + conf_mem.name = "PCIv3 config"; + } + if (range.flags & IORESOURCE_IO) { + of_pci_range_to_resource(&range, np, &io_mem); + io_mem.name = "PCIv3 I/O"; + } + if ((range.flags & IORESOURCE_MEM) && + !(range.flags & IORESOURCE_PREFETCH)) { + of_pci_range_to_resource(&range, np, &non_mem); + non_mem.name = "PCIv3 non-prefetched mem"; + } + if ((range.flags & IORESOURCE_MEM) && + (range.flags & IORESOURCE_PREFETCH)) { + of_pci_range_to_resource(&range, np, &pre_mem); + pre_mem.name = "PCIv3 prefetched mem"; + } + } + + if (!conf_mem.start || !io_mem.start || + !non_mem.start || !pre_mem.start) { + dev_err(&pdev->dev, "missing ranges in device node\n"); + return -EINVAL; + } + + pci_v3.map_irq = pci_v3_map_irq_dt; + pci_common_init_dev(&pdev->dev, &pci_v3); + + return 0; +} + +#else + +static inline int pci_v3_dtprobe(struct platform_device *pdev, + struct device_node *np) +{ + return -EINVAL; +} + +#endif + +static int __init pci_v3_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + int ret; + + /* Remap the Integrator system controller */ + ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100); + if (!ap_syscon_base) { + dev_err(&pdev->dev, "unable to remap the AP syscon for PCIv3\n"); + return -ENODEV; + } + + /* Device tree probe path */ + if (np) + return pci_v3_dtprobe(pdev, np); + + pci_v3_base = devm_ioremap(&pdev->dev, PHYS_PCI_V3_BASE, SZ_64K); + if (!pci_v3_base) { + dev_err(&pdev->dev, "unable to remap PCIv3 base\n"); + return -ENODEV; + } + + ret = devm_request_irq(&pdev->dev, IRQ_AP_V3INT, v3_irq, 0, "V3", NULL); + if (ret) { + dev_err(&pdev->dev, "unable to grab PCI error interrupt: %d\n", + ret); + return -ENODEV; + } + + conf_mem.name = "PCIv3 config"; + conf_mem.start = PHYS_PCI_CONFIG_BASE; + conf_mem.end = PHYS_PCI_CONFIG_BASE + SZ_16M - 1; + conf_mem.flags = IORESOURCE_MEM; + + io_mem.name = "PCIv3 I/O"; + io_mem.start = PHYS_PCI_IO_BASE; + io_mem.end = PHYS_PCI_IO_BASE + SZ_16M - 1; + io_mem.flags = IORESOURCE_MEM; + + non_mem.name = "PCIv3 non-prefetched mem"; + non_mem.start = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START; + non_mem.end = PHYS_PCI_MEM_BASE + PCI_BUS_NONMEM_START + + PCI_BUS_NONMEM_SIZE - 1; + non_mem.flags = IORESOURCE_MEM; + + pre_mem.name = "PCIv3 prefetched mem"; + pre_mem.start = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START; + pre_mem.end = PHYS_PCI_MEM_BASE + PCI_BUS_PREMEM_START + + PCI_BUS_PREMEM_SIZE - 1; + pre_mem.flags = IORESOURCE_MEM | IORESOURCE_PREFETCH; + + pci_v3.map_irq = pci_v3_map_irq; + + pci_common_init_dev(&pdev->dev, &pci_v3); + + return 0; +} + +static const struct of_device_id pci_ids[] = { + { .compatible = "v3,v360epc-pci", }, + {}, +}; + +static struct platform_driver pci_v3_driver = { + .driver = { + .name = "pci-v3", + .of_match_table = pci_ids, + }, +}; + +static int __init pci_v3_init(void) +{ + return platform_driver_probe(&pci_v3_driver, pci_v3_probe); +} + +subsys_initcall(pci_v3_init); + +/* + * Static mappings for the PCIv3 bridge + * + * e8000000 40000000 PCI memory PHYS_PCI_MEM_BASE (max 512M) + * ec000000 61000000 PCI config space PHYS_PCI_CONFIG_BASE (max 16M) + * fee00000 60000000 PCI IO PHYS_PCI_IO_BASE (max 16M) + */ +static struct map_desc pci_v3_io_desc[] __initdata __maybe_unused = { + { + .virtual = (unsigned long)PCI_MEMORY_VADDR, + .pfn = __phys_to_pfn(PHYS_PCI_MEM_BASE), + .length = SZ_16M, + .type = MT_DEVICE + }, { + .virtual = (unsigned long)PCI_CONFIG_VADDR, + .pfn = __phys_to_pfn(PHYS_PCI_CONFIG_BASE), + .length = SZ_16M, + .type = MT_DEVICE + } +}; + +int __init pci_v3_early_init(void) +{ + iotable_init(pci_v3_io_desc, ARRAY_SIZE(pci_v3_io_desc)); + vga_base = (unsigned long)PCI_MEMORY_VADDR; + pci_map_io_early(__phys_to_pfn(PHYS_PCI_IO_BASE)); + return 0; } diff --git a/arch/arm/mach-integrator/pci_v3.h b/arch/arm/mach-integrator/pci_v3.h new file mode 100644 index 00000000000..755fd29fed4 --- /dev/null +++ b/arch/arm/mach-integrator/pci_v3.h @@ -0,0 +1,2 @@ +/* Simple oneliner include to the PCIv3 early init */ +extern int pci_v3_early_init(void); |