diff options
Diffstat (limited to 'arch/arm')
32 files changed, 1278 insertions, 545 deletions
diff --git a/arch/arm/mach-omap1/board-h2-mmc.c b/arch/arm/mach-omap1/board-h2-mmc.c index ab9ee5820c4..409fa56d0a8 100644 --- a/arch/arm/mach-omap1/board-h2-mmc.c +++ b/arch/arm/mach-omap1/board-h2-mmc.c @@ -12,90 +12,68 @@ * published by the Free Software Foundation. */ +#include <linux/platform_device.h> + +#include <linux/i2c/tps65010.h> + #include <mach/mmc.h> #include <mach/gpio.h> -#ifdef CONFIG_MMC_OMAP -static int slot_cover_open; -static struct device *mmc_device; +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) -static int h2_mmc_set_power(struct device *dev, int slot, int power_on, +static int mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1, - power_on ? "on" : "off", vdd); -#endif - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } + if (power_on) + gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 1); + else + gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0); return 0; } -static int h2_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode) +static int mmc_late_init(struct device *dev) { -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d bus_mode %s\n", slot + 1, - bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull"); -#endif - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } + int ret; - return 0; -} + ret = gpio_request(H2_TPS_GPIO_MMC_PWR_EN, "MMC power"); + if (ret < 0) + return ret; -static int h2_mmc_get_cover_state(struct device *dev, int slot) -{ - BUG_ON(slot != 0); - - return slot_cover_open; -} - -void h2_mmc_slot_cover_handler(void *arg, int state) -{ - if (mmc_device == NULL) - return; - - slot_cover_open = state; - omap_mmc_notify_cover_event(mmc_device, 0, state); -} - -static int h2_mmc_late_init(struct device *dev) -{ - int ret = 0; - - mmc_device = dev; + gpio_direction_output(H2_TPS_GPIO_MMC_PWR_EN, 0); return ret; } -static void h2_mmc_cleanup(struct device *dev) +static void mmc_shutdown(struct device *dev) { + gpio_free(H2_TPS_GPIO_MMC_PWR_EN); } -static struct omap_mmc_platform_data h2_mmc_data = { +/* + * H2 could use the following functions tested: + * - mmc_get_cover_state that uses OMAP_MPUIO(1) + * - mmc_get_wp that uses OMAP_MPUIO(3) + */ +static struct omap_mmc_platform_data mmc1_data = { .nr_slots = 1, - .switch_slot = NULL, - .init = h2_mmc_late_init, - .cleanup = h2_mmc_cleanup, + .init = mmc_late_init, + .shutdown = mmc_shutdown, + .dma_mask = 0xffffffff, .slots[0] = { - .set_power = h2_mmc_set_power, - .set_bus_mode = h2_mmc_set_bus_mode, - .get_ro = NULL, - .get_cover_state = h2_mmc_get_cover_state, + .set_power = mmc_set_power, .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 | MMC_VDD_32_33 | MMC_VDD_33_34, .name = "mmcblk", }, }; +static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC]; + void __init h2_mmc_init(void) { - omap_set_mmc_info(1, &h2_mmc_data); + mmc_data[0] = &mmc1_data; + omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC); } #else @@ -104,7 +82,4 @@ void __init h2_mmc_init(void) { } -void h2_mmc_slot_cover_handler(void *arg, int state) -{ -} #endif diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c index c5b4a3b718c..b240c5f861d 100644 --- a/arch/arm/mach-omap1/board-h2.c +++ b/arch/arm/mach-omap1/board-h2.c @@ -345,10 +345,25 @@ static void __init h2_init_smc91x(void) } } +static int tps_setup(struct i2c_client *client, void *context) +{ + tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V | + TPS_LDO1_ENABLE | TPS_VLDO1_3_0V); + + return 0; +} + +static struct tps65010_board tps_board = { + .base = H2_TPS_GPIO_BASE, + .outmask = 0x0f, + .setup = tps_setup, +}; + static struct i2c_board_info __initdata h2_i2c_board_info[] = { { I2C_BOARD_INFO("tps65010", 0x48), .irq = OMAP_GPIO_IRQ(58), + .platform_data = &tps_board, }, { I2C_BOARD_INFO("isp1301_omap", 0x2d), .irq = OMAP_GPIO_IRQ(2), @@ -378,15 +393,6 @@ static struct omap_usb_config h2_usb_config __initdata = { .pins[1] = 3, }; -static struct omap_mmc_config h2_mmc_config __initdata = { - .mmc[0] = { - .enabled = 1, - .wire4 = 1, - }, -}; - -extern struct omap_mmc_platform_data h2_mmc_data; - static struct omap_uart_config h2_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; @@ -397,7 +403,6 @@ static struct omap_lcd_config h2_lcd_config __initdata = { static struct omap_board_config_kernel h2_config[] __initdata = { { OMAP_TAG_USB, &h2_usb_config }, - { OMAP_TAG_MMC, &h2_mmc_config }, { OMAP_TAG_UART, &h2_uart_config }, { OMAP_TAG_LCD, &h2_lcd_config }, }; diff --git a/arch/arm/mach-omap1/board-h3-mmc.c b/arch/arm/mach-omap1/board-h3-mmc.c index 36085819098..fdfe793d56f 100644 --- a/arch/arm/mach-omap1/board-h3-mmc.c +++ b/arch/arm/mach-omap1/board-h3-mmc.c @@ -12,94 +12,55 @@ * published by the Free Software Foundation. */ +#include <linux/platform_device.h> + +#include <linux/i2c/tps65010.h> + #include <mach/mmc.h> #include <mach/gpio.h> -#ifdef CONFIG_MMC_OMAP -static int slot_cover_open; -static struct device *mmc_device; +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) -static int h3_mmc_set_power(struct device *dev, int slot, int power_on, +static int mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1, - power_on ? "on" : "off", vdd); -#endif - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } + if (power_on) + gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 1); + else + gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0); return 0; } -static int h3_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode) -{ - int ret = 0; - -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d bus_mode %s\n", slot + 1, - bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull"); -#endif - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } - - /* Treated on upper level */ - - return bus_mode; -} - -static int h3_mmc_get_cover_state(struct device *dev, int slot) -{ - BUG_ON(slot != 0); - - return slot_cover_open; -} - -void h3_mmc_slot_cover_handler(void *arg, int state) -{ - if (mmc_device == NULL) - return; - - slot_cover_open = state; - omap_mmc_notify_cover_event(mmc_device, 0, state); -} - -static int h3_mmc_late_init(struct device *dev) -{ - int ret = 0; - - mmc_device = dev; - - return ret; -} - -static void h3_mmc_cleanup(struct device *dev) -{ -} - -static struct omap_mmc_platform_data h3_mmc_data = { +/* + * H3 could use the following functions tested: + * - mmc_get_cover_state that uses OMAP_MPUIO(1) + * - mmc_get_wp that maybe uses OMAP_MPUIO(3) + */ +static struct omap_mmc_platform_data mmc1_data = { .nr_slots = 1, - .switch_slot = NULL, - .init = h3_mmc_late_init, - .cleanup = h3_mmc_cleanup, + .dma_mask = 0xffffffff, .slots[0] = { - .set_power = h3_mmc_set_power, - .set_bus_mode = h3_mmc_set_bus_mode, - .get_ro = NULL, - .get_cover_state = h3_mmc_get_cover_state, + .set_power = mmc_set_power, .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 | MMC_VDD_32_33 | MMC_VDD_33_34, .name = "mmcblk", }, }; +static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC]; + void __init h3_mmc_init(void) { - omap_set_mmc_info(1, &h3_mmc_data); + int ret; + + ret = gpio_request(H3_TPS_GPIO_MMC_PWR_EN, "MMC power"); + if (ret < 0) + return; + gpio_direction_output(H3_TPS_GPIO_MMC_PWR_EN, 0); + + mmc_data[0] = &mmc1_data; + omap1_init_mmc(mmc_data, OMAP16XX_NR_MMC); } #else @@ -108,7 +69,4 @@ void __init h3_mmc_init(void) { } -void h3_mmc_slot_cover_handler(void *arg, int state) -{ -} #endif diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c index 0332203bd53..5157eea9be3 100644 --- a/arch/arm/mach-omap1/board-h3.c +++ b/arch/arm/mach-omap1/board-h3.c @@ -447,15 +447,6 @@ static struct omap_usb_config h3_usb_config __initdata = { .pins[1] = 3, }; -static struct omap_mmc_config h3_mmc_config __initdata = { - .mmc[0] = { - .enabled = 1, - .wire4 = 1, - }, -}; - -extern struct omap_mmc_platform_data h3_mmc_data; - static struct omap_uart_config h3_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; @@ -466,7 +457,6 @@ static struct omap_lcd_config h3_lcd_config __initdata = { static struct omap_board_config_kernel h3_config[] __initdata = { { OMAP_TAG_USB, &h3_usb_config }, - { OMAP_TAG_MMC, &h3_mmc_config }, { OMAP_TAG_UART, &h3_uart_config }, { OMAP_TAG_LCD, &h3_lcd_config }, }; diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c index a21e365a7a8..af2fb907008 100644 --- a/arch/arm/mach-omap1/board-innovator.c +++ b/arch/arm/mach-omap1/board-innovator.c @@ -39,6 +39,7 @@ #include <mach/common.h> #include <mach/mcbsp.h> #include <mach/omap-alsa.h> +#include <mach/mmc.h> static int innovator_keymap[] = { KEY(0, 0, KEY_F1), @@ -360,16 +361,49 @@ static struct omap_lcd_config innovator1610_lcd_config __initdata = { }; #endif -static struct omap_mmc_config innovator_mmc_config __initdata = { - .mmc [0] = { - .enabled = 1, - .wire4 = 1, - .wp_pin = OMAP_MPUIO(3), - .power_pin = -1, /* FPGA F3 UIO42 */ - .switch_pin = -1, /* FPGA F4 UIO43 */ +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) + +static int mmc_set_power(struct device *dev, int slot, int power_on, + int vdd) +{ + if (power_on) + fpga_write(fpga_read(OMAP1510_FPGA_POWER) | (1 << 3), + OMAP1510_FPGA_POWER); + else + fpga_write(fpga_read(OMAP1510_FPGA_POWER) & ~(1 << 3), + OMAP1510_FPGA_POWER); + + return 0; +} + +/* + * Innovator could use the following functions tested: + * - mmc_get_wp that uses OMAP_MPUIO(3) + * - mmc_get_cover_state that uses FPGA F4 UIO43 + */ +static struct omap_mmc_platform_data mmc1_data = { + .nr_slots = 1, + .slots[0] = { + .set_power = mmc_set_power, + .wires = 4, + .name = "mmcblk", }, }; +static struct omap_mmc_platform_data *mmc_data[OMAP16XX_NR_MMC]; + +void __init innovator_mmc_init(void) +{ + mmc_data[0] = &mmc1_data; + omap1_init_mmc(mmc_data, OMAP15XX_NR_MMC); +} + +#else +static inline void innovator_mmc_init(void) +{ +} +#endif + static struct omap_uart_config innovator_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; @@ -377,7 +411,6 @@ static struct omap_uart_config innovator_uart_config __initdata = { static struct omap_board_config_kernel innovator_config[] = { { OMAP_TAG_USB, NULL }, { OMAP_TAG_LCD, NULL }, - { OMAP_TAG_MMC, &innovator_mmc_config }, { OMAP_TAG_UART, &innovator_uart_config }, }; @@ -412,6 +445,7 @@ static void __init innovator_init(void) omap_board_config_size = ARRAY_SIZE(innovator_config); omap_serial_init(); omap_register_i2c_bus(1, 100, NULL, 0); + innovator_mmc_init(); } static void __init innovator_map_io(void) diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c index b26782471e5..4970c402a59 100644 --- a/arch/arm/mach-omap1/board-nokia770.c +++ b/arch/arm/mach-omap1/board-nokia770.c @@ -35,6 +35,7 @@ #include <mach/aic23.h> #include <mach/omapfb.h> #include <mach/lcd_mipid.h> +#include <mach/mmc.h> #define ADS7846_PENDOWN_GPIO 15 @@ -173,26 +174,68 @@ static struct omap_usb_config nokia770_usb_config __initdata = { .pins[0] = 6, }; -static struct omap_mmc_config nokia770_mmc_config __initdata = { - .mmc[0] = { - .enabled = 0, - .wire4 = 0, - .wp_pin = -1, - .power_pin = -1, - .switch_pin = -1, - }, - .mmc[1] = { - .enabled = 0, - .wire4 = 0, - .wp_pin = -1, - .power_pin = -1, - .switch_pin = -1, +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) + +#define NOKIA770_GPIO_MMC_POWER 41 +#define NOKIA770_GPIO_MMC_SWITCH 23 + +static int nokia770_mmc_set_power(struct device *dev, int slot, int power_on, + int vdd) +{ + if (power_on) + gpio_set_value(NOKIA770_GPIO_MMC_POWER, 1); + else + gpio_set_value(NOKIA770_GPIO_MMC_POWER, 0); + + return 0; +} + +static int nokia770_mmc_get_cover_state(struct device *dev, int slot) +{ + return gpio_get_value(NOKIA770_GPIO_MMC_SWITCH); +} + +static struct omap_mmc_platform_data nokia770_mmc2_data = { + .nr_slots = 1, + .dma_mask = 0xffffffff, + .slots[0] = { + .set_power = nokia770_mmc_set_power, + .get_cover_state = nokia770_mmc_get_cover_state, + .name = "mmcblk", }, }; +static struct omap_mmc_platform_data *nokia770_mmc_data[OMAP16XX_NR_MMC]; + +static void __init nokia770_mmc_init(void) +{ + int ret; + + ret = gpio_request(NOKIA770_GPIO_MMC_POWER, "MMC power"); + if (ret < 0) + return; + gpio_direction_output(NOKIA770_GPIO_MMC_POWER, 0); + + ret = gpio_request(NOKIA770_GPIO_MMC_SWITCH, "MMC cover"); + if (ret < 0) { + gpio_free(NOKIA770_GPIO_MMC_POWER); + return; + } + gpio_direction_input(NOKIA770_GPIO_MMC_SWITCH); + + /* Only the second MMC controller is used */ + nokia770_mmc_data[1] = &nokia770_mmc2_data; + omap1_init_mmc(nokia770_mmc_data, OMAP16XX_NR_MMC); +} + +#else +static inline void nokia770_mmc_init(void) +{ +} +#endif + static struct omap_board_config_kernel nokia770_config[] __initdata = { { OMAP_TAG_USB, NULL }, - { OMAP_TAG_MMC, &nokia770_mmc_config }, }; #if defined(CONFIG_OMAP_DSP) @@ -335,6 +378,7 @@ static void __init omap_nokia770_init(void) omap_dsp_init(); ads7846_dev_init(); mipid_dev_init(); + nokia770_mmc_init(); } static void __init omap_nokia770_map_io(void) diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c index 4141e3917d7..75e32d35afd 100644 --- a/arch/arm/mach-omap1/board-palmte.c +++ b/arch/arm/mach-omap1/board-palmte.c @@ -316,7 +316,6 @@ static void palmte_get_power_status(struct apm_power_info *info, int *battery) static struct omap_board_config_kernel palmte_config[] __initdata = { { OMAP_TAG_USB, &palmte_usb_config }, - { OMAP_TAG_MMC, &palmte_mmc_config }, { OMAP_TAG_LCD, &palmte_lcd_config }, { OMAP_TAG_UART, &palmte_uart_config }, }; diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c index 801fb5f62ed..cc05257eb1c 100644 --- a/arch/arm/mach-omap1/board-palmz71.c +++ b/arch/arm/mach-omap1/board-palmz71.c @@ -267,16 +267,6 @@ static struct omap_usb_config palmz71_usb_config __initdata = { .pins[0] = 2, }; -static struct omap_mmc_config palmz71_mmc_config __initdata = { - .mmc[0] = { - .enabled = 1, - .wire4 = 0, - .wp_pin = PALMZ71_MMC_WP_GPIO, - .power_pin = -1, - .switch_pin = PALMZ71_MMC_IN_GPIO, - }, -}; - static struct omap_lcd_config palmz71_lcd_config __initdata = { .ctrl_name = "internal", }; @@ -287,7 +277,6 @@ static struct omap_uart_config palmz71_uart_config __initdata = { static struct omap_board_config_kernel palmz71_config[] __initdata = { {OMAP_TAG_USB, &palmz71_usb_config}, - {OMAP_TAG_MMC, &palmz71_mmc_config}, {OMAP_TAG_LCD, &palmz71_lcd_config}, {OMAP_TAG_UART, &palmz71_uart_config}, }; diff --git a/arch/arm/mach-omap1/board-sx1-mmc.c b/arch/arm/mach-omap1/board-sx1-mmc.c index 0be4ebaa284..66a4d7d5255 100644 --- a/arch/arm/mach-omap1/board-sx1-mmc.c +++ b/arch/arm/mach-omap1/board-sx1-mmc.c @@ -12,30 +12,20 @@ * published by the Free Software Foundation. */ +#include <linux/platform_device.h> + #include <mach/hardware.h> #include <mach/mmc.h> #include <mach/gpio.h> -#ifdef CONFIG_MMC_OMAP -static int slot_cover_open; -static struct device *mmc_device; +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) -static int sx1_mmc_set_power(struct device *dev, int slot, int power_on, +static int mmc_set_power(struct device *dev, int slot, int power_on, int vdd) { int err; u8 dat = 0; -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1, - power_on ? "on" : "off", vdd); -#endif - - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } - err = sx1_i2c_read_byte(SOFIA_I2C_ADDR, SOFIA_POWER1_REG, &dat); if (err < 0) return err; @@ -48,68 +38,23 @@ static int sx1_mmc_set_power(struct device *dev, int slot, int power_on, return sx1_i2c_write_byte(SOFIA_I2C_ADDR, SOFIA_POWER1_REG, dat); } -static int sx1_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode) -{ -#ifdef CONFIG_MMC_DEBUG - dev_dbg(dev, "Set slot %d bus_mode %s\n", slot + 1, - bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull"); -#endif - if (slot != 0) { - dev_err(dev, "No such slot %d\n", slot + 1); - return -ENODEV; - } - - return 0; -} - -static int sx1_mmc_get_cover_state(struct device *dev, int slot) -{ - BUG_ON(slot != 0); - - return slot_cover_open; -} - -void sx1_mmc_slot_cover_handler(void *arg, int state) -{ - if (mmc_device == NULL) - return; - - slot_cover_open = state; - omap_mmc_notify_cover_event(mmc_device, 0, state); -} - -static int sx1_mmc_late_init(struct device *dev) -{ - int ret = 0; - - mmc_device = dev; - - return ret; -} - -static void sx1_mmc_cleanup(struct device *dev) -{ -} - -static struct omap_mmc_platform_data sx1_mmc_data = { +/* Cover switch is at OMAP_MPUIO(3) */ +static struct omap_mmc_platform_data mmc1_data = { .nr_slots = 1, - .switch_slot = NULL, - .init = sx1_mmc_late_init, - .cleanup = sx1_mmc_cleanup, .slots[0] = { - .set_power = sx1_mmc_set_power, - .set_bus_mode = sx1_mmc_set_bus_mode, - .get_ro = NULL, - .get_cover_state = sx1_mmc_get_cover_state, + .set_power = mmc_set_power, .ocr_mask = MMC_VDD_28_29 | MMC_VDD_30_31 | MMC_VDD_32_33 | MMC_VDD_33_34, .name = "mmcblk", }, }; +static struct omap_mmc_platform_data *mmc_data[OMAP15XX_NR_MMC]; + void __init sx1_mmc_init(void) { - omap_set_mmc_info(1, &sx1_mmc_data); + mmc_data[0] = &mmc1_data; + omap1_init_mmc(mmc_data, OMAP15XX_NR_MMC); } #else @@ -118,7 +63,4 @@ void __init sx1_mmc_init(void) { } -void sx1_mmc_slot_cover_handler(void *arg, int state) -{ -} #endif diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c index 93bd395b997..8171fe0ca08 100644 --- a/arch/arm/mach-omap1/board-sx1.c +++ b/arch/arm/mach-omap1/board-sx1.c @@ -378,15 +378,6 @@ static struct omap_usb_config sx1_usb_config __initdata = { .pins[2] = 0, }; -/*----------- MMC -------------------------*/ - -static struct omap_mmc_config sx1_mmc_config __initdata = { - .mmc [0] = { - .enabled = 1, - .wire4 = 0, - }, -}; - /*----------- LCD -------------------------*/ static struct platform_device sx1_lcd_device = { @@ -414,7 +405,6 @@ static struct omap_uart_config sx1_uart_config __initdata = { static struct omap_board_config_kernel sx1_config[] __initdata = { { OMAP_TAG_USB, &sx1_usb_config }, - { OMAP_TAG_MMC, &sx1_mmc_config }, { OMAP_TAG_LCD, &sx1_lcd_config }, { OMAP_TAG_UART, &sx1_uart_config }, }; diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c index 92c9de1090a..c224f3c6423 100644 --- a/arch/arm/mach-omap1/board-voiceblue.c +++ b/arch/arm/mach-omap1/board-voiceblue.c @@ -15,6 +15,7 @@ #include <linux/delay.h> #include <linux/platform_device.h> #include <linux/interrupt.h> +#include <linux/irq.h> #include <linux/init.h> #include <linux/kernel.h> #include <linux/notifier.h> @@ -140,21 +141,12 @@ static struct omap_usb_config voiceblue_usb_config __initdata = { .pins[2] = 6, }; -static struct omap_mmc_config voiceblue_mmc_config __initdata = { - .mmc[0] = { - .enabled = 1, - .power_pin = 2, - .switch_pin = -1, - }, -}; - static struct omap_uart_config voiceblue_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; static struct omap_board_config_kernel voiceblue_config[] = { { OMAP_TAG_USB, &voiceblue_usb_config }, - { OMAP_TAG_MMC, &voiceblue_mmc_config }, { OMAP_TAG_UART, &voiceblue_uart_config }, }; diff --git a/arch/arm/mach-omap1/clock.h b/arch/arm/mach-omap1/clock.h index 5635b511ab6..c1dcdf18d8d 100644 --- a/arch/arm/mach-omap1/clock.h +++ b/arch/arm/mach-omap1/clock.h @@ -705,7 +705,6 @@ static struct clk bclk_16xx = { static struct clk mmc1_ck = { .name = "mmc_ck", - .id = 1, /* Functional clock is direct from ULPD, interface clock is ARMPER */ .parent = &armper_ck.clk, .rate = 48000000, @@ -720,7 +719,7 @@ static struct clk mmc1_ck = { static struct clk mmc2_ck = { .name = "mmc_ck", - .id = 2, + .id = 1, /* Functional clock is direct from ULPD, interface clock is ARMPER */ .parent = &armper_ck.clk, .rate = 48000000, diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c index e382b438c64..77382d8b6b2 100644 --- a/arch/arm/mach-omap1/devices.c +++ b/arch/arm/mach-omap1/devices.c @@ -22,6 +22,7 @@ #include <mach/board.h> #include <mach/mux.h> #include <mach/gpio.h> +#include <mach/mmc.h> /*-------------------------------------------------------------------------*/ @@ -99,6 +100,95 @@ static inline void omap_init_mbox(void) static inline void omap_init_mbox(void) { } #endif +/*-------------------------------------------------------------------------*/ + +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) + +static inline void omap1_mmc_mux(struct omap_mmc_platform_data *mmc_controller, + int controller_nr) +{ + if (controller_nr == 0) { + omap_cfg_reg(MMC_CMD); + omap_cfg_reg(MMC_CLK); + omap_cfg_reg(MMC_DAT0); + if (cpu_is_omap1710()) { + omap_cfg_reg(M15_1710_MMC_CLKI); + omap_cfg_reg(P19_1710_MMC_CMDDIR); + omap_cfg_reg(P20_1710_MMC_DATDIR0); + } + if (mmc_controller->slots[0].wires == 4) { + omap_cfg_reg(MMC_DAT1); + /* NOTE: DAT2 can be on W10 (here) or M15 */ + if (!mmc_controller->slots[0].nomux) + omap_cfg_reg(MMC_DAT2); + omap_cfg_reg(MMC_DAT3); + } + } + + /* Block 2 is on newer chips, and has many pinout options */ + if (cpu_is_omap16xx() && controller_nr == 1) { + if (!mmc_controller->slots[1].nomux) { + omap_cfg_reg(Y8_1610_MMC2_CMD); + omap_cfg_reg(Y10_1610_MMC2_CLK); + omap_cfg_reg(R18_1610_MMC2_CLKIN); + omap_cfg_reg(W8_1610_MMC2_DAT0); + if (mmc_controller->slots[1].wires == 4) { + omap_cfg_reg(V8_1610_MMC2_DAT1); + omap_cfg_reg(W15_1610_MMC2_DAT2); + omap_cfg_reg(R10_1610_MMC2_DAT3); + } + + /* These are needed for the level shifter */ + omap_cfg_reg(V9_1610_MMC2_CMDDIR); + omap_cfg_reg(V5_1610_MMC2_DATDIR0); + omap_cfg_reg(W19_1610_MMC2_DATDIR1); + } + + /* Feedback clock must be set on OMAP-1710 MMC2 */ + if (cpu_is_omap1710()) + omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24), + MOD_CONF_CTRL_1); + } +} + +void __init omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers) +{ + int i; + + for (i = 0; i < nr_controllers; i++) { + unsigned long base, size; + unsigned int irq = 0; + + if (!mmc_data[i]) + continue; + + omap1_mmc_mux(mmc_data[i], i); + + switch (i) { + case 0: + base = OMAP1_MMC1_BASE; + irq = INT_MMC; + break; + case 1: + if (!cpu_is_omap16xx()) + return; + base = OMAP1_MMC2_BASE; + irq = INT_1610_MMC2; + break; + default: + continue; + } + size = OMAP1_MMC_SIZE; + + omap_mmc_add(i, base, size, irq, mmc_data[i]); + }; +} + +#endif + +/*-------------------------------------------------------------------------*/ + #if defined(CONFIG_OMAP_STI) #define OMAP1_STI_BASE 0xfffea000 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index f12c43e4932..bbd12bc10fd 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -27,10 +27,15 @@ obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o # Specific board support obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o -obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o +obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o \ + mmc-twl4030.o obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o -obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o -obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o -obj-$(CONFIG_MACH_OVERO) += board-overo.o -obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o +obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o \ + mmc-twl4030.o +obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o \ + mmc-twl4030.o +obj-$(CONFIG_MACH_OVERO) += board-overo.o \ + mmc-twl4030.o +obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o \ + mmc-twl4030.o diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 6748de6e19a..83fa37211d7 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -19,6 +19,7 @@ #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h> #include <linux/delay.h> +#include <linux/i2c/twl4030.h> #include <linux/err.h> #include <linux/clk.h> #include <linux/io.h> @@ -35,6 +36,7 @@ #include <mach/common.h> #include <mach/gpmc.h> +#include "mmc-twl4030.h" #define SDP2430_FLASH_CS 0 #define SDP2430_SMC91X_CS 5 @@ -197,12 +199,58 @@ static struct omap_board_config_kernel sdp2430_config[] = { {OMAP_TAG_UART, &sdp2430_uart_config}, }; + +static struct twl4030_gpio_platform_data sdp2430_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, +}; + +static struct twl4030_platform_data sdp2430_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .gpio = &sdp2430_gpio_data, +}; + +static struct i2c_board_info __initdata sdp2430_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl4030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_24XX_SYS_NIRQ, + .platform_data = &sdp2430_twldata, + }, +}; + +static int __init omap2430_i2c_init(void) +{ + omap_register_i2c_bus(1, 400, NULL, 0); + omap_register_i2c_bus(2, 2600, sdp2430_i2c_boardinfo, + ARRAY_SIZE(sdp2430_i2c_boardinfo)); + return 0; +} + +static struct twl4030_hsmmc_info mmc[] __initdata = { + { + .mmc = 1, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .ext_clock = 1, + }, + {} /* Terminator */ +}; + static void __init omap_2430sdp_init(void) { + omap2430_i2c_init(); + platform_add_devices(sdp2430_devices, ARRAY_SIZE(sdp2430_devices)); omap_board_config = sdp2430_config; omap_board_config_size = ARRAY_SIZE(sdp2430_config); omap_serial_init(); + twl4030_mmc_init(mmc); } static void __init omap_2430sdp_map_io(void) diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c index d83035b436d..bf1e5d32c2a 100644 --- a/arch/arm/mach-omap2/board-apollon.c +++ b/arch/arm/mach-omap2/board-apollon.c @@ -261,16 +261,6 @@ static struct omap_uart_config apollon_uart_config __initdata = { .enabled_uarts = (1 << 0) | (0 << 1) | (0 << 2), }; -static struct omap_mmc_config apollon_mmc_config __initdata = { - .mmc [0] = { - .enabled = 1, - .wire4 = 1, - .wp_pin = -1, - .power_pin = -1, - .switch_pin = -1, - }, -}; - static struct omap_usb_config apollon_usb_config __initdata = { .register_dev = 1, .hmc_mode = 0x14, /* 0:dev 1:host1 2:disable */ @@ -284,7 +274,6 @@ static struct omap_lcd_config apollon_lcd_config __initdata = { static struct omap_board_config_kernel apollon_config[] = { { OMAP_TAG_UART, &apollon_uart_config }, - { OMAP_TAG_MMC, &apollon_mmc_config }, { OMAP_TAG_USB, &apollon_usb_config }, { OMAP_TAG_LCD, &apollon_lcd_config }, }; diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 9ba097868e7..3b34c20d1df 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -41,19 +41,8 @@ static struct omap_uart_config generic_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; -static struct omap_mmc_config generic_mmc_config __initdata = { - .mmc [0] = { - .enabled = 0, - .wire4 = 0, - .wp_pin = -1, - .power_pin = -1, - .switch_pin = -1, - }, -}; - static struct omap_board_config_kernel generic_config[] = { { OMAP_TAG_UART, &generic_uart_config }, - { OMAP_TAG_MMC, &generic_mmc_config }, }; static void __init omap_generic_init(void) diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index 7de0506e1e2..5e9b14675b1 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -373,23 +373,12 @@ static struct omap_uart_config h4_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; -static struct omap_mmc_config h4_mmc_config __initdata = { - .mmc [0] = { - .enabled = 1, - .wire4 = 1, - .wp_pin = -1, - .power_pin = -1, - .switch_pin = -1, - }, -}; - static struct omap_lcd_config h4_lcd_config __initdata = { .ctrl_name = "internal", }; static struct omap_board_config_kernel h4_config[] = { { OMAP_TAG_UART, &h4_uart_config }, - { OMAP_TAG_MMC, &h4_mmc_config }, { OMAP_TAG_LCD, &h4_lcd_config }, }; diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index 43c7ac4b7f8..aa6972781e4 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -21,6 +21,7 @@ #include <linux/clk.h> #include <linux/spi/spi.h> #include <linux/spi/ads7846.h> +#include <linux/i2c/twl4030.h> #include <mach/hardware.h> #include <asm/mach-types.h> @@ -38,6 +39,8 @@ #include <asm/delay.h> #include <mach/control.h> +#include "mmc-twl4030.h" + #define SDP3430_SMC91X_CS 3 static struct resource ldp_smc911x_resources[] = { @@ -109,14 +112,48 @@ static struct omap_board_config_kernel ldp_config[] __initdata = { { OMAP_TAG_UART, &ldp_uart_config }, }; +static struct twl4030_gpio_platform_data ldp_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, +}; + +static struct twl4030_platform_data ldp_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .gpio = &ldp_gpio_data, +}; + +static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl4030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &ldp_twldata, + }, +}; + static int __init omap_i2c_init(void) { - omap_register_i2c_bus(1, 2600, NULL, 0); + omap_register_i2c_bus(1, 2600, ldp_i2c_boardinfo, + ARRAY_SIZE(ldp_i2c_boardinfo)); omap_register_i2c_bus(2, 400, NULL, 0); omap_register_i2c_bus(3, 400, NULL, 0); return 0; } +static struct twl4030_hsmmc_info mmc[] __initdata = { + { + .mmc = 1, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + }, + {} /* Terminator */ +}; + static void __init omap_ldp_init(void) { omap_i2c_init(); @@ -124,6 +161,7 @@ static void __init omap_ldp_init(void) omap_board_config = ldp_config; omap_board_config_size = ARRAY_SIZE(ldp_config); omap_serial_init(); + twl4030_mmc_init(mmc); } static void __init omap_ldp_map_io(void) diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index baa79674e9d..9e5ada01b5f 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -38,7 +38,9 @@ #include <mach/common.h> #include <mach/gpmc.h> #include <mach/nand.h> +#include <mach/mux.h> +#include "mmc-twl4030.h" #define GPMC_CS0_BASE 0x60 #define GPMC_CS_SIZE 0x30 @@ -103,6 +105,78 @@ static struct omap_uart_config omap3_beagle_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; +static struct twl4030_hsmmc_info mmc[] = { + { + .mmc = 1, + .wires = 8, + .gpio_wp = 29, + }, + {} /* Terminator */ +}; + +static struct gpio_led gpio_leds[]; + +static int beagle_twl_gpio_setup(struct device *dev, + unsigned gpio, unsigned ngpio) +{ + /* gpio + 0 is "mmc0_cd" (input/IRQ) */ + + /* REVISIT: need ehci-omap hooks for external VBUS + * power switch and overcurrent detect + */ + + gpio_request(gpio + 1, "EHCI_nOC"); + gpio_direction_input(gpio + 1); + + /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */ + gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR"); + gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1); + + /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ + gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + + return 0; +} + +static struct twl4030_gpio_platform_data beagle_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, + .use_leds = true, + .pullups = BIT(1), + .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13) + | BIT(15) | BIT(16) | BIT(17), + .setup = beagle_twl_gpio_setup, +}; + +static struct twl4030_platform_data beagle_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .gpio = &beagle_gpio_data, +}; + +static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl4030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &beagle_twldata, + }, +}; + +static int __init omap3_beagle_i2c_init(void) +{ + omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo, + ARRAY_SIZE(beagle_i2c_boardinfo)); +#ifdef CONFIG_I2C2_OMAP_BEAGLE + omap_register_i2c_bus(2, 400, NULL, 0); +#endif + omap_register_i2c_bus(3, 400, NULL, 0); + return 0; +} + static void __init omap3_beagle_init_irq(void) { omap2_init_common_hw(); @@ -130,6 +204,11 @@ static struct gpio_led gpio_leds[] = { .default_trigger = "mmc0", .gpio = 149, }, + { + .name = "beagleboard::pmu_stat", + .gpio = -EINVAL, /* gets replaced */ + .active_low = true, + }, }; static struct gpio_led_platform_data gpio_led_info = { @@ -218,11 +297,22 @@ static void __init omap3beagle_flash_init(void) static void __init omap3_beagle_init(void) { + omap3_beagle_i2c_init(); platform_add_devices(omap3_beagle_devices, ARRAY_SIZE(omap3_beagle_devices)); omap_board_config = omap3_beagle_config; omap_board_config_size = ARRAY_SIZE(omap3_beagle_config); omap_serial_init(); + + omap_cfg_reg(AH8_34XX_GPIO29); + mmc[0].gpio_cd = gpio + 0; + twl4030_mmc_init(mmc); + + omap_cfg_reg(J25_34XX_GPIO170); + gpio_request(170, "DVI_nPD"); + /* REVISIT leave DVI powered down until it's needed ... */ + gpio_direction_output(170, true); + omap3beagle_flash_init(); } diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 7236c7be05b..b3196107afd 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -35,16 +35,48 @@ #include <mach/hardware.h> #include <mach/mcspi.h> +#include "mmc-twl4030.h" + #define OMAP3_PANDORA_TS_GPIO 94 +static struct twl4030_hsmmc_info omap3pandora_mmc[] = { + { + .mmc = 1, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = 126, + .ext_clock = 0, + }, + { + .mmc = 2, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = 127, + .ext_clock = 1, + }, + {} /* Terminator */ +}; + static struct omap_uart_config omap3pandora_uart_config __initdata = { .enabled_uarts = (1 << 2), /* UART3 */ }; +static int omap3pandora_twl_gpio_setup(struct device *dev, + unsigned gpio, unsigned ngpio) +{ + /* gpio + {0,1} is "mmc{0,1}_cd" (input/IRQ) */ + omap3pandora_mmc[0].gpio_cd = gpio + 0; + omap3pandora_mmc[1].gpio_cd = gpio + 1; + twl4030_mmc_init(omap3pandora_mmc); + + return 0; +} + static struct twl4030_gpio_platform_data omap3pandora_gpio_data = { .gpio_base = OMAP_MAX_GPIO_LINES, .irq_base = TWL4030_GPIO_IRQ_BASE, .irq_end = TWL4030_GPIO_IRQ_END, + .setup = omap3pandora_twl_gpio_setup, }; static struct twl4030_usb_data omap3pandora_usb_data = { diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index e09aa59a399..82b3dc557c9 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -26,6 +26,7 @@ #include <linux/io.h> #include <linux/kernel.h> #include <linux/platform_device.h> +#include <linux/i2c/twl4030.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> @@ -44,6 +45,8 @@ #include <mach/hardware.h> #include <mach/nand.h> +#include "mmc-twl4030.h" + #define NAND_BLOCK_SIZE SZ_128K #define GPMC_CS0_BASE 0x60 #define GPMC_CS_SIZE 0x30 @@ -139,8 +142,31 @@ static struct omap_uart_config overo_uart_config __initdata = { .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), }; +static struct twl4030_gpio_platform_data overo_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, +}; + +static struct twl4030_platform_data overo_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + .gpio = &overo_gpio_data, +}; + +static struct i2c_board_info __initdata overo_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl4030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &overo_twldata, + }, +}; + static int __init overo_i2c_init(void) { + omap_register_i2c_bus(1, 2600, overo_i2c_boardinfo, + ARRAY_SIZE(overo_i2c_boardinfo)); /* i2c2 pins are used for gpio */ omap_register_i2c_bus(3, 400, NULL, 0); return 0; @@ -171,6 +197,22 @@ static struct platform_device *overo_devices[] __initdata = { &overo_lcd_device, }; +static struct twl4030_hsmmc_info mmc[] __initdata = { + { + .mmc = 1, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + }, + { + .mmc = 2, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + }, + {} /* Terminator */ +}; + static void __init overo_init(void) { overo_i2c_init(); @@ -178,6 +220,7 @@ static void __init overo_init(void) omap_board_config = overo_config; omap_board_config_size = ARRAY_SIZE(overo_config); omap_serial_init(); + twl4030_mmc_init(mmc); overo_flash_init(); if ((gpio_request(OVERO_GPIO_W2W_NRESET, diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 242a19d86cc..ff6cd14d254 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -2522,7 +2522,6 @@ static struct clk usbhs_ick = { static struct clk mmchs1_ick = { .name = "mmchs_ick", - .id = 1, .parent = &l4_ck, .flags = CLOCK_IN_OMAP243X, .clkdm_name = "core_l4_clkdm", @@ -2533,7 +2532,6 @@ static struct clk mmchs1_ick = { static struct clk mmchs1_fck = { .name = "mmchs_fck", - .id = 1, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP243X, .clkdm_name = "core_l3_clkdm", @@ -2544,7 +2542,7 @@ static struct clk mmchs1_fck = { static struct clk mmchs2_ick = { .name = "mmchs_ick", - .id = 2, + .id = 1, .parent = &l4_ck, .flags = CLOCK_IN_OMAP243X, .clkdm_name = "core_l4_clkdm", @@ -2555,7 +2553,7 @@ static struct clk mmchs2_ick = { static struct clk mmchs2_fck = { .name = "mmchs_fck", - .id = 2, + .id = 1, .parent = &func_96m_ck, .flags = CLOCK_IN_OMAP243X, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, OMAP24XX_CM_FCLKEN2), @@ -2595,7 +2593,6 @@ static struct clk mdm_intc_ick = { static struct clk mmchsdb1_fck = { .name = "mmchsdb_fck", - .id = 1, .parent = &func_32k_ck, .flags = CLOCK_IN_OMAP243X, .clkdm_name = "core_l4_clkdm", @@ -2606,7 +2603,7 @@ static struct clk mmchsdb1_fck = { static struct clk mmchsdb2_fck = { .name = "mmchsdb_fck", - .id = 2, + .id = 1, .parent = &func_32k_ck, .flags = CLOCK_IN_OMAP243X, .clkdm_name = "core_l4_clkdm", diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index 7217a0824ec..a826094d89b 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -1374,7 +1374,7 @@ static struct clk core_96m_fck = { static struct clk mmchs3_fck = { .name = "mmchs_fck", - .id = 3, + .id = 2, .parent = &core_96m_fck, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430ES2_EN_MMC3_SHIFT, @@ -1385,7 +1385,7 @@ static struct clk mmchs3_fck = { static struct clk mmchs2_fck = { .name = "mmchs_fck", - .id = 2, + .id = 1, .parent = &core_96m_fck, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_MMC2_SHIFT, @@ -1406,7 +1406,6 @@ static struct clk mspro_fck = { static struct clk mmchs1_fck = { .name = "mmchs_fck", - .id = 1, .parent = &core_96m_fck, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), .enable_bit = OMAP3430_EN_MMC1_SHIFT, @@ -1722,7 +1721,7 @@ static struct clk usbtll_ick = { static struct clk mmchs3_ick = { .name = "mmchs_ick", - .id = 3, + .id = 2, .parent = &core_l4_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430ES2_EN_MMC3_SHIFT, @@ -1774,7 +1773,7 @@ static struct clk des2_ick = { static struct clk mmchs2_ick = { .name = "mmchs_ick", - .id = 2, + .id = 1, .parent = &core_l4_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_MMC2_SHIFT, @@ -1785,7 +1784,6 @@ static struct clk mmchs2_ick = { static struct clk mmchs1_ick = { .name = "mmchs_ick", - .id = 1, .parent = &core_l4_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_MMC1_SHIFT, diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 90af2ac469a..9d7216ff6c9 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -14,16 +14,19 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/io.h> +#include <linux/clk.h> #include <mach/hardware.h> #include <asm/mach-types.h> #include <asm/mach/map.h> +#include <mach/control.h> #include <mach/tc.h> #include <mach/board.h> #include <mach/mux.h> #include <mach/gpio.h> #include <mach/eac.h> +#include <mach/mmc.h> #if defined(CONFIG_OMAP_DSP) || defined(CONFIG_OMAP_DSP_MODULE) #define OMAP2_MBOX_BASE IO_ADDRESS(OMAP24XX_MAILBOX_BASE) @@ -295,6 +298,171 @@ static void omap_init_sha1_md5(void) static inline void omap_init_sha1_md5(void) { } #endif +/*-------------------------------------------------------------------------*/ + +#ifdef CONFIG_ARCH_OMAP3 + +#define MMCHS_SYSCONFIG 0x0010 +#define MMCHS_SYSCONFIG_SWRESET (1 << 1) +#define MMCHS_SYSSTATUS 0x0014 +#define MMCHS_SYSSTATUS_RESETDONE (1 << 0) + +static struct platform_device dummy_pdev = { + .dev = { + .bus = &platform_bus_type, + }, +}; + +/** + * omap_hsmmc_reset() - Full reset of each HS-MMC controller + * + * Ensure that each MMC controller is fully reset. Controllers + * left in an unknown state (by bootloader) may prevent retention + * or OFF-mode. This is especially important in cases where the + * MMC driver is not enabled, _or_ built as a module. + * + * In order for reset to work, interface, functional and debounce + * clocks must be enabled. The debounce clock comes from func_32k_clk + * and is not under SW control, so we only enable i- and f-clocks. + **/ +static void __init omap_hsmmc_reset(void) +{ + u32 i, nr_controllers = cpu_is_omap34xx() ? OMAP34XX_NR_MMC : + OMAP24XX_NR_MMC; + + for (i = 0; i < nr_controllers; i++) { + u32 v, base = 0; + struct clk *iclk, *fclk; + struct device *dev = &dummy_pdev.dev; + + switch (i) { + case 0: + base = OMAP2_MMC1_BASE; + break; + case 1: + base = OMAP2_MMC2_BASE; + break; + case 2: + base = OMAP3_MMC3_BASE; + break; + } + + dummy_pdev.id = i; + iclk = clk_get(dev, "mmchs_ick"); + if (iclk && clk_enable(iclk)) + iclk = NULL; + + fclk = clk_get(dev, "mmchs_fck"); + if (fclk && clk_enable(fclk)) + fclk = NULL; + + if (!iclk || !fclk) { + printk(KERN_WARNING + "%s: Unable to enable clocks for MMC%d, " + "cannot reset.\n", __func__, i); + break; + } + + omap_writel(MMCHS_SYSCONFIG_SWRESET, base + MMCHS_SYSCONFIG); + v = omap_readl(base + MMCHS_SYSSTATUS); + while (!(omap_readl(base + MMCHS_SYSSTATUS) & + MMCHS_SYSSTATUS_RESETDONE)) + cpu_relax(); + + if (fclk) { + clk_disable(fclk); + clk_put(fclk); + } + if (iclk) { + clk_disable(iclk); + clk_put(iclk); + } + } +} +#else +static inline void omap_hsmmc_reset(void) {} +#endif + +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ + defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE) + +static inline void omap2_mmc_mux(struct omap_mmc_platform_data *mmc_controller, + int controller_nr) +{ + if (cpu_is_omap2420() && controller_nr == 0) { + omap_cfg_reg(H18_24XX_MMC_CMD); + omap_cfg_reg(H15_24XX_MMC_CLKI); + omap_cfg_reg(G19_24XX_MMC_CLKO); + omap_cfg_reg(F20_24XX_MMC_DAT0); + omap_cfg_reg(F19_24XX_MMC_DAT_DIR0); + omap_cfg_reg(G18_24XX_MMC_CMD_DIR); + if (mmc_controller->slots[0].wires == 4) { + omap_cfg_reg(H14_24XX_MMC_DAT1); + omap_cfg_reg(E19_24XX_MMC_DAT2); + omap_cfg_reg(D19_24XX_MMC_DAT3); + omap_cfg_reg(E20_24XX_MMC_DAT_DIR1); + omap_cfg_reg(F18_24XX_MMC_DAT_DIR2); + omap_cfg_reg(E18_24XX_MMC_DAT_DIR3); + } + + /* + * Use internal loop-back in MMC/SDIO Module Input Clock + * selection + */ + if (mmc_controller->slots[0].internal_clock) { + u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0); + v |= (1 << 24); + omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0); + } + } +} + +void __init omap2_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers) +{ + int i; + + for (i = 0; i < nr_controllers; i++) { + unsigned long base, size; + unsigned int irq = 0; + + if (!mmc_data[i]) + continue; + + omap2_mmc_mux(mmc_data[i], i); + + switch (i) { + case 0: + base = OMAP2_MMC1_BASE; + irq = INT_24XX_MMC_IRQ; + break; + case 1: + base = OMAP2_MMC2_BASE; + irq = INT_24XX_MMC2_IRQ; + break; + case 2: + if (!cpu_is_omap34xx()) + return; + base = OMAP3_MMC3_BASE; + irq = INT_34XX_MMC3_IRQ; + break; + default: + continue; + } + + if (cpu_is_omap2420()) + size = OMAP2420_MMC_SIZE; + else + size = HSMMC_SIZE; + + omap_mmc_add(i, base, size, irq, mmc_data[i]); + }; +} + +#endif + +/*-------------------------------------------------------------------------*/ + #if defined(CONFIG_HDQ_MASTER_OMAP) || defined(CONFIG_HDQ_MASTER_OMAP_MODULE) #if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3430) #define OMAP_HDQ_BASE 0x480B2000 @@ -334,6 +502,7 @@ static int __init omap2_init_devices(void) /* please keep these calls, and their implementations above, * in alphabetical order so they're easier to sort through. */ + omap_hsmmc_reset(); omap_init_mbox(); omap_init_mcspi(); omap_hdq_init(); diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c new file mode 100644 index 00000000000..437f52073f6 --- /dev/null +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -0,0 +1,408 @@ +/* + * linux/arch/arm/mach-omap2/mmc-twl4030.c + * + * Copyright (C) 2007-2008 Texas Instruments + * Copyright (C) 2008 Nokia Corporation + * Author: Texas Instruments + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/err.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/i2c/twl4030.h> + +#include <mach/hardware.h> +#include <mach/control.h> +#include <mach/mmc.h> +#include <mach/board.h> + +#include "mmc-twl4030.h" + +#if defined(CONFIG_TWL4030_CORE) && \ + (defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)) + +#define LDO_CLR 0x00 +#define VSEL_S2_CLR 0x40 + +#define VMMC1_DEV_GRP 0x27 +#define VMMC1_CLR 0x00 +#define VMMC1_315V 0x03 +#define VMMC1_300V 0x02 +#define VMMC1_285V 0x01 +#define VMMC1_185V 0x00 +#define VMMC1_DEDICATED 0x2A + +#define VMMC2_DEV_GRP 0x2B +#define VMMC2_CLR 0x40 +#define VMMC2_315V 0x0c +#define VMMC2_300V 0x0b +#define VMMC2_285V 0x0a +#define VMMC2_260V 0x08 +#define VMMC2_185V 0x06 +#define VMMC2_DEDICATED 0x2E + +#define VMMC_DEV_GRP_P1 0x20 + +static u16 control_pbias_offset; +static u16 control_devconf1_offset; + +#define HSMMC_NAME_LEN 9 + +static struct twl_mmc_controller { + struct omap_mmc_platform_data *mmc; + u8 twl_vmmc_dev_grp; + u8 twl_mmc_dedicated; + char name[HSMMC_NAME_LEN]; +} hsmmc[] = { + { + .twl_vmmc_dev_grp = VMMC1_DEV_GRP, + .twl_mmc_dedicated = VMMC1_DEDICATED, + }, + { + .twl_vmmc_dev_grp = VMMC2_DEV_GRP, + .twl_mmc_dedicated = VMMC2_DEDICATED, + }, +}; + +static int twl_mmc_card_detect(int irq) +{ + unsigned i; + + for (i = 0; i < ARRAY_SIZE(hsmmc); i++) { + struct omap_mmc_platform_data *mmc; + + mmc = hsmmc[i].mmc; + if (!mmc) + continue; + if (irq != mmc->slots[0].card_detect_irq) + continue; + + /* NOTE: assumes card detect signal is active-low */ + return !gpio_get_value_cansleep(mmc->slots[0].switch_pin); + } + return -ENOSYS; +} + +static int twl_mmc_get_ro(struct device *dev, int slot) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + + /* NOTE: assumes write protect signal is active-high */ + return gpio_get_value_cansleep(mmc->slots[0].gpio_wp); +} + +/* + * MMC Slot Initialization. + */ +static int twl_mmc_late_init(struct device *dev) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + int ret = 0; + int i; + + ret = gpio_request(mmc->slots[0].switch_pin, "mmc_cd"); + if (ret) + goto done; + ret = gpio_direction_input(mmc->slots[0].switch_pin); + if (ret) + goto err; + + for (i = 0; i < ARRAY_SIZE(hsmmc); i++) { + if (hsmmc[i].name == mmc->slots[0].name) { + hsmmc[i].mmc = mmc; + break; + } + } + + return 0; + +err: + gpio_free(mmc->slots[0].switch_pin); +done: + mmc->slots[0].card_detect_irq = 0; + mmc->slots[0].card_detect = NULL; + + dev_err(dev, "err %d configuring card detect\n", ret); + return ret; +} + +static void twl_mmc_cleanup(struct device *dev) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + + gpio_free(mmc->slots[0].switch_pin); +} + +#ifdef CONFIG_PM + +static int twl_mmc_suspend(struct device *dev, int slot) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + + disable_irq(mmc->slots[0].card_detect_irq); + return 0; +} + +static int twl_mmc_resume(struct device *dev, int slot) +{ + struct omap_mmc_platform_data *mmc = dev->platform_data; + + enable_irq(mmc->slots[0].card_detect_irq); + return 0; +} + +#else +#define twl_mmc_suspend NULL +#define twl_mmc_resume NULL +#endif + +/* + * Sets the MMC voltage in twl4030 + */ +static int twl_mmc_set_voltage(struct twl_mmc_controller *c, int vdd) +{ + int ret; + u8 vmmc, dev_grp_val; + + switch (1 << vdd) { + case MMC_VDD_35_36: + case MMC_VDD_34_35: + case MMC_VDD_33_34: + case MMC_VDD_32_33: + case MMC_VDD_31_32: + case MMC_VDD_30_31: + if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) + vmmc = VMMC1_315V; + else + vmmc = VMMC2_315V; + break; + case MMC_VDD_29_30: + if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) + vmmc = VMMC1_315V; + else + vmmc = VMMC2_300V; + break; + case MMC_VDD_27_28: + case MMC_VDD_26_27: + if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) + vmmc = VMMC1_285V; + else + vmmc = VMMC2_285V; + break; + case MMC_VDD_25_26: + case MMC_VDD_24_25: + case MMC_VDD_23_24: + case MMC_VDD_22_23: + case MMC_VDD_21_22: + case MMC_VDD_20_21: + if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) + vmmc = VMMC1_285V; + else + vmmc = VMMC2_260V; + break; + case MMC_VDD_165_195: + if (c->twl_vmmc_dev_grp == VMMC1_DEV_GRP) + vmmc = VMMC1_185V; + else + vmmc = VMMC2_185V; + break; + default: + vmmc = 0; + break; + } + + if (vmmc) + dev_grp_val = VMMC_DEV_GRP_P1; /* Power up */ + else + dev_grp_val = LDO_CLR; /* Power down */ + + ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, + dev_grp_val, c->twl_vmmc_dev_grp); + if (ret) + return ret; + + ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, + vmmc, c->twl_mmc_dedicated); + + return ret; +} + +static int twl_mmc1_set_power(struct device *dev, int slot, int power_on, + int vdd) +{ + u32 reg; + int ret = 0; + struct twl_mmc_controller *c = &hsmmc[0]; + struct omap_mmc_platform_data *mmc = dev->platform_data; + + if (power_on) { + if (cpu_is_omap2430()) { + reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1); + if ((1 << vdd) >= MMC_VDD_30_31) + reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE; + else + reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE; + omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1); + } + + if (mmc->slots[0].internal_clock) { + reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0); + reg |= OMAP2_MMCSDIO1ADPCLKISEL; + omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0); + } + + reg = omap_ctrl_readl(control_pbias_offset); + reg |= OMAP2_PBIASSPEEDCTRL0; + reg &= ~OMAP2_PBIASLITEPWRDNZ0; + omap_ctrl_writel(reg, control_pbias_offset); + + ret = twl_mmc_set_voltage(c, vdd); + + /* 100ms delay required for PBIAS configuration */ + msleep(100); + reg = omap_ctrl_readl(control_pbias_offset); + reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0); + if ((1 << vdd) <= MMC_VDD_165_195) + reg &= ~OMAP2_PBIASLITEVMODE0; + else + reg |= OMAP2_PBIASLITEVMODE0; + omap_ctrl_writel(reg, control_pbias_offset); + } else { + reg = omap_ctrl_readl(control_pbias_offset); + reg &= ~OMAP2_PBIASLITEPWRDNZ0; + omap_ctrl_writel(reg, control_pbias_offset); + + ret = twl_mmc_set_voltage(c, 0); + + /* 100ms delay required for PBIAS configuration */ + msleep(100); + reg = omap_ctrl_readl(control_pbias_offset); + reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 | + OMAP2_PBIASLITEVMODE0); + omap_ctrl_writel(reg, control_pbias_offset); + } + + return ret; +} + +static int twl_mmc2_set_power(struct device *dev, int slot, int power_on, int vdd) +{ + int ret; + struct twl_mmc_controller *c = &hsmmc[1]; + struct omap_mmc_platform_data *mmc = dev->platform_data; + + if (power_on) { + if (mmc->slots[0].internal_clock) { + u32 reg; + + reg = omap_ctrl_readl(control_devconf1_offset); + reg |= OMAP2_MMCSDIO2ADPCLKISEL; + omap_ctrl_writel(reg, control_devconf1_offset); + } + ret = twl_mmc_set_voltage(c, vdd); + } else { + ret = twl_mmc_set_voltage(c, 0); + } + + return ret; +} + +static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata; + +void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers) +{ + struct twl4030_hsmmc_info *c; + int nr_hsmmc = ARRAY_SIZE(hsmmc_data); + + if (cpu_is_omap2430()) { + control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE; + control_devconf1_offset = OMAP243X_CONTROL_DEVCONF1; + nr_hsmmc = 2; + } else { + control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE; + control_devconf1_offset = OMAP343X_CONTROL_DEVCONF1; + } + + for (c = controllers; c->mmc; c++) { + struct twl_mmc_controller *twl = hsmmc + c->mmc - 1; + struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1]; + + if (!c->mmc || c->mmc > nr_hsmmc) { + pr_debug("MMC%d: no such controller\n", c->mmc); + continue; + } + if (mmc) { + pr_debug("MMC%d: already configured\n", c->mmc); + continue; + } + + mmc = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL); + if (!mmc) { + pr_err("Cannot allocate memory for mmc device!\n"); + return; + } + + sprintf(twl->name, "mmc%islot%i", c->mmc, 1); + mmc->slots[0].name = twl->name; + mmc->nr_slots = 1; + mmc->slots[0].ocr_mask = MMC_VDD_165_195 | + MMC_VDD_26_27 | MMC_VDD_27_28 | + MMC_VDD_29_30 | + MMC_VDD_30_31 | MMC_VDD_31_32; + mmc->slots[0].wires = c->wires; + mmc->slots[0].internal_clock = !c->ext_clock; + mmc->dma_mask = 0xffffffff; + + /* note: twl4030 card detect GPIOs normally switch VMMCx ... */ + if (gpio_is_valid(c->gpio_cd)) { + mmc->init = twl_mmc_late_init; + mmc->cleanup = twl_mmc_cleanup; + mmc->suspend = twl_mmc_suspend; + mmc->resume = twl_mmc_resume; + + mmc->slots[0].switch_pin = c->gpio_cd; + mmc->slots[0].card_detect_irq = gpio_to_irq(c->gpio_cd); + mmc->slots[0].card_detect = twl_mmc_card_detect; + } else + mmc->slots[0].switch_pin = -EINVAL; + + /* write protect normally uses an OMAP gpio */ + if (gpio_is_valid(c->gpio_wp)) { + gpio_request(c->gpio_wp, "mmc_wp"); + gpio_direction_input(c->gpio_wp); + + mmc->slots[0].gpio_wp = c->gpio_wp; + mmc->slots[0].get_ro = twl_mmc_get_ro; + } else + mmc->slots[0].gpio_wp = -EINVAL; + + /* NOTE: we assume OMAP's MMC1 and MMC2 use + * the TWL4030's VMMC1 and VMMC2, respectively; + * and that OMAP's MMC3 isn't used. + */ + + switch (c->mmc) { + case 1: + mmc->slots[0].set_power = twl_mmc1_set_power; + break; + case 2: + mmc->slots[0].set_power = twl_mmc2_set_power; + break; + default: + pr_err("MMC%d configuration not supported!\n", c->mmc); + continue; + } + hsmmc_data[c->mmc - 1] = mmc; + } + + omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC); +} + +#endif diff --git a/arch/arm/mach-omap2/mmc-twl4030.h b/arch/arm/mach-omap2/mmc-twl4030.h new file mode 100644 index 00000000000..e1c8076400c --- /dev/null +++ b/arch/arm/mach-omap2/mmc-twl4030.h @@ -0,0 +1,29 @@ +/* + * MMC definitions for OMAP2 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +struct twl4030_hsmmc_info { + u8 mmc; /* controller 1/2/3 */ + u8 wires; /* 1/4/8 wires */ + int gpio_cd; /* or -EINVAL */ + int gpio_wp; /* or -EINVAL */ + int ext_clock:1; /* use external pin for input clock */ +}; + +#if defined(CONFIG_TWL4030_CORE) && \ + (defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ + defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)) + +void twl4030_mmc_init(struct twl4030_hsmmc_info *); + +#else + +static inline void twl4030_mmc_init(struct twl4030_hsmmc_info *info) +{ +} + +#endif diff --git a/arch/arm/plat-omap/devices.c b/arch/arm/plat-omap/devices.c index 0cb2b22388e..ac15c23fd5d 100644 --- a/arch/arm/plat-omap/devices.c +++ b/arch/arm/plat-omap/devices.c @@ -192,202 +192,48 @@ void omap_mcbsp_register_board_cfg(struct omap_mcbsp_platform_data *config, /*-------------------------------------------------------------------------*/ -#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE) -#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) -#define OMAP_MMC1_BASE 0x4809c000 -#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x1fc) -#define OMAP_MMC1_INT INT_24XX_MMC_IRQ +#define OMAP_MMC_NR_RES 2 -#define OMAP_MMC2_BASE 0x480b4000 -#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x1fc) -#define OMAP_MMC2_INT INT_24XX_MMC2_IRQ - -#else - -#define OMAP_MMC1_BASE 0xfffb7800 -#define OMAP_MMC1_END (OMAP_MMC1_BASE + 0x7f) -#define OMAP_MMC1_INT INT_MMC - -#define OMAP_MMC2_BASE 0xfffb7c00 /* omap16xx only */ -#define OMAP_MMC2_END (OMAP_MMC2_BASE + 0x7f) -#define OMAP_MMC2_INT INT_1610_MMC2 - -#endif - -static struct omap_mmc_platform_data mmc1_data; - -static u64 mmc1_dmamask = 0xffffffff; - -static struct resource mmc1_resources[] = { - { - .start = OMAP_MMC1_BASE, - .end = OMAP_MMC1_END, - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_MMC1_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device mmc_omap_device1 = { - .name = "mmci-omap", - .id = 1, - .dev = { - .dma_mask = &mmc1_dmamask, - .platform_data = &mmc1_data, - }, - .num_resources = ARRAY_SIZE(mmc1_resources), - .resource = mmc1_resources, -}; - -#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \ - defined(CONFIG_ARCH_OMAP34XX) - -static struct omap_mmc_platform_data mmc2_data; - -static u64 mmc2_dmamask = 0xffffffff; - -static struct resource mmc2_resources[] = { - { - .start = OMAP_MMC2_BASE, - .end = OMAP_MMC2_END, - .flags = IORESOURCE_MEM, - }, - { - .start = OMAP_MMC2_INT, - .flags = IORESOURCE_IRQ, - }, -}; - -static struct platform_device mmc_omap_device2 = { - .name = "mmci-omap", - .id = 2, - .dev = { - .dma_mask = &mmc2_dmamask, - .platform_data = &mmc2_data, - }, - .num_resources = ARRAY_SIZE(mmc2_resources), - .resource = mmc2_resources, -}; -#endif - -static inline void omap_init_mmc_conf(const struct omap_mmc_config *mmc_conf) -{ - if (cpu_is_omap2430() || cpu_is_omap34xx()) - return; - - if (mmc_conf->mmc[0].enabled) { - if (cpu_is_omap24xx()) { - omap_cfg_reg(H18_24XX_MMC_CMD); - omap_cfg_reg(H15_24XX_MMC_CLKI); - omap_cfg_reg(G19_24XX_MMC_CLKO); - omap_cfg_reg(F20_24XX_MMC_DAT0); - omap_cfg_reg(F19_24XX_MMC_DAT_DIR0); - omap_cfg_reg(G18_24XX_MMC_CMD_DIR); - } else { - omap_cfg_reg(MMC_CMD); - omap_cfg_reg(MMC_CLK); - omap_cfg_reg(MMC_DAT0); - if (cpu_is_omap1710()) { - omap_cfg_reg(M15_1710_MMC_CLKI); - omap_cfg_reg(P19_1710_MMC_CMDDIR); - omap_cfg_reg(P20_1710_MMC_DATDIR0); - } - } - if (mmc_conf->mmc[0].wire4) { - if (cpu_is_omap24xx()) { - omap_cfg_reg(H14_24XX_MMC_DAT1); - omap_cfg_reg(E19_24XX_MMC_DAT2); - omap_cfg_reg(D19_24XX_MMC_DAT3); - omap_cfg_reg(E20_24XX_MMC_DAT_DIR1); - omap_cfg_reg(F18_24XX_MMC_DAT_DIR2); - omap_cfg_reg(E18_24XX_MMC_DAT_DIR3); - } else { - omap_cfg_reg(MMC_DAT1); - /* NOTE: DAT2 can be on W10 (here) or M15 */ - if (!mmc_conf->mmc[0].nomux) - omap_cfg_reg(MMC_DAT2); - omap_cfg_reg(MMC_DAT3); - } - } - } - -#ifdef CONFIG_ARCH_OMAP16XX - /* block 2 is on newer chips, and has many pinout options */ - if (mmc_conf->mmc[1].enabled) { - if (!mmc_conf->mmc[1].nomux) { - omap_cfg_reg(Y8_1610_MMC2_CMD); - omap_cfg_reg(Y10_1610_MMC2_CLK); - omap_cfg_reg(R18_1610_MMC2_CLKIN); - omap_cfg_reg(W8_1610_MMC2_DAT0); - if (mmc_conf->mmc[1].wire4) { - omap_cfg_reg(V8_1610_MMC2_DAT1); - omap_cfg_reg(W15_1610_MMC2_DAT2); - omap_cfg_reg(R10_1610_MMC2_DAT3); - } - - /* These are needed for the level shifter */ - omap_cfg_reg(V9_1610_MMC2_CMDDIR); - omap_cfg_reg(V5_1610_MMC2_DATDIR0); - omap_cfg_reg(W19_1610_MMC2_DATDIR1); - } - - /* Feedback clock must be set on OMAP-1710 MMC2 */ - if (cpu_is_omap1710()) - omap_writel(omap_readl(MOD_CONF_CTRL_1) | (1 << 24), - MOD_CONF_CTRL_1); - } -#endif -} - -static void __init omap_init_mmc(void) +/* + * Register MMC devices. Called from mach-omap1 and mach-omap2 device init. + */ +int __init omap_mmc_add(int id, unsigned long base, unsigned long size, + unsigned int irq, struct omap_mmc_platform_data *data) { - const struct omap_mmc_config *mmc_conf; - - /* NOTE: assumes MMC was never (wrongly) enabled */ - mmc_conf = omap_get_config(OMAP_TAG_MMC, struct omap_mmc_config); - if (!mmc_conf) - return; - - omap_init_mmc_conf(mmc_conf); - - if (mmc_conf->mmc[0].enabled) { - mmc1_data.conf = mmc_conf->mmc[0]; - (void) platform_device_register(&mmc_omap_device1); - } - -#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \ - defined(CONFIG_ARCH_OMAP34XX) - if (mmc_conf->mmc[1].enabled) { - mmc2_data.conf = mmc_conf->mmc[1]; - (void) platform_device_register(&mmc_omap_device2); - } -#endif -} + struct platform_device *pdev; + struct resource res[OMAP_MMC_NR_RES]; + int ret; + + pdev = platform_device_alloc("mmci-omap", id); + if (!pdev) + return -ENOMEM; + + memset(res, 0, OMAP_MMC_NR_RES * sizeof(struct resource)); + res[0].start = base; + res[0].end = base + size - 1; + res[0].flags = IORESOURCE_MEM; + res[1].start = res[1].end = irq; + res[1].flags = IORESOURCE_IRQ; + + ret = platform_device_add_resources(pdev, res, ARRAY_SIZE(res)); + if (ret == 0) + ret = platform_device_add_data(pdev, data, sizeof(*data)); + if (ret) + goto fail; + + ret = platform_device_add(pdev); + if (ret) + goto fail; + return 0; -void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info) -{ - switch (host) { - case 1: - mmc1_data = *info; - break; -#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2430) || \ - defined(CONFIG_ARCH_OMAP34XX) - case 2: - mmc2_data = *info; - break; -#endif - default: - BUG(); - } +fail: + platform_device_put(pdev); + return ret; } -#else -static inline void omap_init_mmc(void) {} -void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info) {} #endif /*-------------------------------------------------------------------------*/ @@ -532,7 +378,6 @@ static int __init omap_init_devices(void) */ omap_init_dsp(); omap_init_kp(); - omap_init_mmc(); omap_init_uwire(); omap_init_wdt(); omap_init_rng(); diff --git a/arch/arm/plat-omap/include/mach/board-h2.h b/arch/arm/plat-omap/include/mach/board-h2.h index 2a050e9be65..15531c8dc0e 100644 --- a/arch/arm/plat-omap/include/mach/board-h2.h +++ b/arch/arm/plat-omap/include/mach/board-h2.h @@ -29,13 +29,13 @@ #ifndef __ASM_ARCH_OMAP_H2_H #define __ASM_ARCH_OMAP_H2_H -/* Placeholder for H2 specific defines */ - /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */ #define OMAP1610_ETHR_START 0x04000300 +#define H2_TPS_GPIO_BASE (OMAP_MAX_GPIO_LINES + 16 /* MPUIO */) +# define H2_TPS_GPIO_MMC_PWR_EN (H2_TPS_GPIO_BASE + 3) + extern void h2_mmc_init(void); -extern void h2_mmc_slot_cover_handler(void *arg, int state); #endif /* __ASM_ARCH_OMAP_H2_H */ diff --git a/arch/arm/plat-omap/include/mach/board.h b/arch/arm/plat-omap/include/mach/board.h index c23c12ccb35..9466772fc7c 100644 --- a/arch/arm/plat-omap/include/mach/board.h +++ b/arch/arm/plat-omap/include/mach/board.h @@ -16,7 +16,6 @@ /* Different peripheral ids */ #define OMAP_TAG_CLOCK 0x4f01 -#define OMAP_TAG_MMC 0x4f02 #define OMAP_TAG_SERIAL_CONSOLE 0x4f03 #define OMAP_TAG_USB 0x4f04 #define OMAP_TAG_LCD 0x4f05 @@ -35,27 +34,6 @@ struct omap_clock_config { u8 system_clock_type; }; -struct omap_mmc_conf { - unsigned enabled:1; - /* nomux means "standard" muxing is wrong on this board, and that - * board-specific code handled it before common init logic. - */ - unsigned nomux:1; - /* switch pin can be for card detect (default) or card cover */ - unsigned cover:1; - /* 4 wire signaling is optional, and is only used for SD/SDIO */ - unsigned wire4:1; - /* use the internal clock */ - unsigned internal_clock:1; - s16 power_pin; - s16 switch_pin; - s16 wp_pin; -}; - -struct omap_mmc_config { - struct omap_mmc_conf mmc[2]; -}; - struct omap_serial_console_config { u8 console_uart; u32 console_speed; diff --git a/arch/arm/plat-omap/include/mach/control.h b/arch/arm/plat-omap/include/mach/control.h index dc988676057..269147f3836 100644 --- a/arch/arm/plat-omap/include/mach/control.h +++ b/arch/arm/plat-omap/include/mach/control.h @@ -74,6 +74,7 @@ #define OMAP243X_CONTROL_IVA2_BOOTADDR (OMAP2_CONTROL_GENERAL + 0x0190) #define OMAP243X_CONTROL_IVA2_BOOTMOD (OMAP2_CONTROL_GENERAL + 0x0194) #define OMAP243X_CONTROL_IVA2_GEMCFG (OMAP2_CONTROL_GENERAL + 0x0198) +#define OMAP243X_CONTROL_PBIAS_LITE (OMAP2_CONTROL_GENERAL + 0x0230) /* 24xx-only CONTROL_GENERAL register offsets */ #define OMAP24XX_CONTROL_DEBOBS (OMAP2_CONTROL_GENERAL + 0x0000) @@ -140,6 +141,7 @@ #define OMAP343X_CONTROL_TEST_KEY_13 (OMAP2_CONTROL_GENERAL + 0x00fc) #define OMAP343X_CONTROL_IVA2_BOOTADDR (OMAP2_CONTROL_GENERAL + 0x0190) #define OMAP343X_CONTROL_IVA2_BOOTMOD (OMAP2_CONTROL_GENERAL + 0x0194) +#define OMAP343X_CONTROL_PBIAS_LITE (OMAP2_CONTROL_GENERAL + 0x02b0) #define OMAP343X_CONTROL_TEMP_SENSOR (OMAP2_CONTROL_GENERAL + 0x02b4) /* @@ -154,11 +156,14 @@ * and the security mode (secure, non-secure, don't care) */ /* CONTROL_DEVCONF0 bits */ +#define OMAP2_MMCSDIO1ADPCLKISEL (1 << 24) /* MMC1 loop back clock */ #define OMAP24XX_USBSTANDBYCTRL (1 << 15) #define OMAP2_MCBSP2_CLKS_MASK (1 << 6) #define OMAP2_MCBSP1_CLKS_MASK (1 << 2) /* CONTROL_DEVCONF1 bits */ +#define OMAP243X_MMC1_ACTIVE_OVERWRITE (1 << 31) +#define OMAP2_MMCSDIO2ADPCLKISEL (1 << 6) /* MMC2 loop back clock */ #define OMAP2_MCBSP5_CLKS_MASK (1 << 4) /* > 242x */ #define OMAP2_MCBSP4_CLKS_MASK (1 << 2) /* > 242x */ #define OMAP2_MCBSP3_CLKS_MASK (1 << 0) /* > 242x */ @@ -172,6 +177,18 @@ #define OMAP2_SYSBOOT_1_MASK (1 << 1) #define OMAP2_SYSBOOT_0_MASK (1 << 0) +/* CONTROL_PBIAS_LITE bits */ +#define OMAP343X_PBIASLITESUPPLY_HIGH1 (1 << 15) +#define OMAP343X_PBIASLITEVMODEERROR1 (1 << 11) +#define OMAP343X_PBIASSPEEDCTRL1 (1 << 10) +#define OMAP343X_PBIASLITEPWRDNZ1 (1 << 9) +#define OMAP343X_PBIASLITEVMODE1 (1 << 8) +#define OMAP343X_PBIASLITESUPPLY_HIGH0 (1 << 7) +#define OMAP343X_PBIASLITEVMODEERROR0 (1 << 3) +#define OMAP2_PBIASSPEEDCTRL0 (1 << 2) +#define OMAP2_PBIASLITEPWRDNZ0 (1 << 1) +#define OMAP2_PBIASLITEVMODE0 (1 << 0) + #ifndef __ASSEMBLY__ #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) extern void __iomem *omap_ctrl_base_get(void); diff --git a/arch/arm/plat-omap/include/mach/mmc.h b/arch/arm/plat-omap/include/mach/mmc.h index fc15d13058f..031250f0280 100644 --- a/arch/arm/plat-omap/include/mach/mmc.h +++ b/arch/arm/plat-omap/include/mach/mmc.h @@ -17,12 +17,28 @@ #include <mach/board.h> +#define OMAP15XX_NR_MMC 1 +#define OMAP16XX_NR_MMC 2 +#define OMAP1_MMC_SIZE 0x080 +#define OMAP1_MMC1_BASE 0xfffb7800 +#define OMAP1_MMC2_BASE 0xfffb7c00 /* omap16xx only */ + +#define OMAP24XX_NR_MMC 2 +#define OMAP34XX_NR_MMC 3 +#define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE +#define HSMMC_SIZE 0x200 +#define OMAP2_MMC1_BASE 0x4809c000 +#define OMAP2_MMC2_BASE 0x480b4000 +#define OMAP3_MMC3_BASE 0x480ad000 +#define HSMMC3 (1 << 2) +#define HSMMC2 (1 << 1) +#define HSMMC1 (1 << 0) + #define OMAP_MMC_MAX_SLOTS 2 struct omap_mmc_platform_data { - struct omap_mmc_conf conf; - /* number of slots on board */ + /* number of slots per controller */ unsigned nr_slots:2; /* set if your board has components or wiring that limits the @@ -41,7 +57,31 @@ struct omap_mmc_platform_data { int (*suspend)(struct device *dev, int slot); int (*resume)(struct device *dev, int slot); + u64 dma_mask; + struct omap_mmc_slot_data { + + /* 4 wire signaling is optional, and is used for SD/SDIO/HSMMC; + * 8 wire signaling is also optional, and is used with HSMMC + */ + u8 wires; + + /* + * nomux means "standard" muxing is wrong on this board, and + * that board-specific code handled it before common init logic. + */ + unsigned nomux:1; + + /* switch pin can be for card detect (default) or card cover */ + unsigned cover:1; + + /* use the internal clock */ + unsigned internal_clock:1; + s16 power_pin; + + int switch_pin; /* gpio (card detect) */ + int gpio_wp; /* gpio (write protect) */ + int (* set_bus_mode)(struct device *dev, int slot, int bus_mode); int (* set_power)(struct device *dev, int slot, int power_on, int vdd); int (* get_ro)(struct device *dev, int slot); @@ -49,8 +89,8 @@ struct omap_mmc_platform_data { /* return MMC cover switch state, can be NULL if not supported. * * possible return values: - * 0 - open - * 1 - closed + * 0 - closed + * 1 - open */ int (* get_cover_state)(struct device *dev, int slot); @@ -66,9 +106,31 @@ struct omap_mmc_platform_data { } slots[OMAP_MMC_MAX_SLOTS]; }; -extern void omap_set_mmc_info(int host, const struct omap_mmc_platform_data *info); - /* called from board-specific card detection service routine */ extern void omap_mmc_notify_cover_event(struct device *dev, int slot, int is_closed); +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE) || \ + defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE) +void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers); +void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers); +int omap_mmc_add(int id, unsigned long base, unsigned long size, + unsigned int irq, struct omap_mmc_platform_data *data); +#else +static inline void omap1_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers) +{ +} +static inline void omap2_init_mmc(struct omap_mmc_platform_data **mmc_data, + int nr_controllers) +{ +} +static inline int omap_mmc_add(int id, unsigned long base, unsigned long size, + unsigned int irq, struct omap_mmc_platform_data *data) +{ + return 0; +} + +#endif #endif |