diff options
Diffstat (limited to 'arch/avr32/boards/atngw100/setup.c')
| -rw-r--r-- | arch/avr32/boards/atngw100/setup.c | 36 |
1 files changed, 26 insertions, 10 deletions
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index c7fe94d03a1..32fb9ba0fbd 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -9,6 +9,7 @@ */ #include <linux/clk.h> #include <linux/etherdevice.h> +#include <linux/gpio.h> #include <linux/irq.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> @@ -23,10 +24,10 @@ #include <asm/io.h> #include <asm/setup.h> -#include <asm/arch/at32ap700x.h> -#include <asm/arch/board.h> -#include <asm/arch/init.h> -#include <asm/arch/portmux.h> +#include <mach/at32ap700x.h> +#include <mach/board.h> +#include <mach/init.h> +#include <mach/portmux.h> /* Oscillator frequencies. These are board-specific */ unsigned long at32_board_osc_rates[3] = { @@ -47,14 +48,22 @@ static struct eth_platform_data __initdata eth_data[2]; static struct spi_board_info spi0_board_info[] __initdata = { { .modalias = "mtd_dataflash", - .max_speed_hz = 10000000, + .max_speed_hz = 8000000, .chip_select = 0, }, }; static struct mci_platform_data __initdata mci0_data = { - .detect_pin = GPIO_PIN_PC(25), - .wp_pin = GPIO_PIN_PE(0), + .slot[0] = { + .bus_width = 4, +#ifndef CONFIG_BOARD_ATNGW100_EVKLCD10X + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(0), +#else + .detect_pin = GPIO_PIN_NONE, + .wp_pin = GPIO_PIN_NONE, +#endif + }, }; /* @@ -168,8 +177,6 @@ static int __init atngw100_init(void) * reserve any pins for it. */ - at32_add_system_devices(); - at32_add_device_usart(0); set_hw_addr(at32_add_device_eth(0, ð_data[0])); @@ -190,7 +197,7 @@ static int __init atngw100_init(void) * PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus), * but it's not available off-board. */ - at32_select_periph(GPIO_PIN_PB(28), 0, AT32_GPIOF_PULLUP); + at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP); at32_select_gpio(i2c_gpio_data.sda_pin, AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH); at32_select_gpio(i2c_gpio_data.scl_pin, @@ -204,6 +211,15 @@ postcore_initcall(atngw100_init); static int __init atngw100_arch_init(void) { + /* PB30 is the otherwise unused jumper on the mainboard, with an + * external pullup; the jumper grounds it. Use it however you + * like, including letting U-Boot or Linux tweak boot sequences. + */ + at32_select_gpio(GPIO_PIN_PB(30), 0); + gpio_request(GPIO_PIN_PB(30), "j15"); + gpio_direction_input(GPIO_PIN_PB(30)); + gpio_export(GPIO_PIN_PB(30), false); + /* set_irq_type() after the arch_initcall for EIC has run, and * before the I2C subsystem could try using this IRQ. */ |