summaryrefslogtreecommitdiffstats
path: root/arch/avr32/boards/atngw100/setup.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/avr32/boards/atngw100/setup.c')
-rw-r--r--arch/avr32/boards/atngw100/setup.c26
1 files changed, 21 insertions, 5 deletions
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index b8286f1ce85..32fb9ba0fbd 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -9,6 +9,7 @@
*/
#include <linux/clk.h>
#include <linux/etherdevice.h>
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
@@ -53,8 +54,16 @@ static struct spi_board_info spi0_board_info[] __initdata = {
};
static struct mci_platform_data __initdata mci0_data = {
- .detect_pin = GPIO_PIN_PC(25),
- .wp_pin = GPIO_PIN_PE(0),
+ .slot[0] = {
+ .bus_width = 4,
+#ifndef CONFIG_BOARD_ATNGW100_EVKLCD10X
+ .detect_pin = GPIO_PIN_PC(25),
+ .wp_pin = GPIO_PIN_PE(0),
+#else
+ .detect_pin = GPIO_PIN_NONE,
+ .wp_pin = GPIO_PIN_NONE,
+#endif
+ },
};
/*
@@ -168,8 +177,6 @@ static int __init atngw100_init(void)
* reserve any pins for it.
*/
- at32_add_system_devices();
-
at32_add_device_usart(0);
set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
@@ -190,7 +197,7 @@ static int __init atngw100_init(void)
* PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus),
* but it's not available off-board.
*/
- at32_select_periph(GPIO_PIN_PB(28), 0, AT32_GPIOF_PULLUP);
+ at32_select_periph(GPIO_PIOB_BASE, 1 << 28, 0, AT32_GPIOF_PULLUP);
at32_select_gpio(i2c_gpio_data.sda_pin,
AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
at32_select_gpio(i2c_gpio_data.scl_pin,
@@ -204,6 +211,15 @@ postcore_initcall(atngw100_init);
static int __init atngw100_arch_init(void)
{
+ /* PB30 is the otherwise unused jumper on the mainboard, with an
+ * external pullup; the jumper grounds it. Use it however you
+ * like, including letting U-Boot or Linux tweak boot sequences.
+ */
+ at32_select_gpio(GPIO_PIN_PB(30), 0);
+ gpio_request(GPIO_PIN_PB(30), "j15");
+ gpio_direction_input(GPIO_PIN_PB(30));
+ gpio_export(GPIO_PIN_PB(30), false);
+
/* set_irq_type() after the arch_initcall for EIC has run, and
* before the I2C subsystem could try using this IRQ.
*/