diff options
Diffstat (limited to 'arch/avr32/boards/atstk1000/Kconfig')
| -rw-r--r-- | arch/avr32/boards/atstk1000/Kconfig | 79 |
1 files changed, 79 insertions, 0 deletions
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig new file mode 100644 index 00000000000..718578f6406 --- /dev/null +++ b/arch/avr32/boards/atstk1000/Kconfig @@ -0,0 +1,79 @@ +# STK1000 customization + +if BOARD_ATSTK1002 + +config BOARD_ATSTK1002_CUSTOM + bool "Non-default STK-1002 jumper settings" + help + You will normally leave the jumpers on the CPU card at their + default settings. If you need to use certain peripherals, + you will need to change some of those jumpers. + +if BOARD_ATSTK1002_CUSTOM + +config BOARD_ATSTK1002_SW1_CUSTOM + bool "SW1: use SSC1 (not SPI0)" + help + This also prevents using the external DAC as an audio interface, + and means you can't initialize the on-board QVGA display. + +config BOARD_ATSTK1002_SW2_CUSTOM + bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)" + help + If you change this you'll want an updated boot loader putting + the console on UART-C not UART-A. + +config BOARD_ATSTK1002_SW3_CUSTOM + bool "SW3: use TIMER1 (not SSC0 and GCLK)" + help + This also prevents using the external DAC as an audio interface. + +config BOARD_ATSTK1002_SW4_CUSTOM + bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)" + help + To use the camera interface you'll need a custom card (on the + PCI-format connector) connect a video sensor. + +config BOARD_ATSTK1002_SW5_CUSTOM + bool "SW5: use MACB1 (not LCDC)" + +config BOARD_ATSTK1002_SW6_CUSTOM + bool "SW6: more GPIOs (not MACB0)" + +endif # custom + +config BOARD_ATSTK1002_SPI1 + bool "Configure SPI1 controller" + depends on !BOARD_ATSTK1002_SW4_CUSTOM + help + All the signals for the second SPI controller are available on + GPIO lines and accessed through the J1 jumper block. Say "y" + here to configure that SPI controller. + +config BOARD_ATSTK1002_J2_LED + bool + default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB + +choice + prompt "LEDs connected to J2:" + depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM + optional + help + Select this if you have jumpered the J2 jumper block to the + LED0..LED7 amber leds, or to the RGB leds, using a ten-pin + IDC cable. A default "heartbeat" trigger is provided, but + you can of course override this. + +config BOARD_ATSTK1002_J2_LED8 + bool "LED0..LED7" + help + Select this if J2 is jumpered to LED0..LED7 amber leds. + +config BOARD_ATSTK1002_J2_RGB + bool "RGB leds" + help + Select this if J2 is jumpered to the RGB leds. + +endchoice + +endif # stk 1002 |