summaryrefslogtreecommitdiffstats
path: root/arch/avr32/boards
diff options
context:
space:
mode:
Diffstat (limited to 'arch/avr32/boards')
-rw-r--r--arch/avr32/boards/atngw100/evklcd10x.c50
-rw-r--r--arch/avr32/boards/atngw100/setup.c7
-rw-r--r--arch/avr32/boards/atstk1000/atstk1002.c6
-rw-r--r--arch/avr32/boards/atstk1000/atstk1003.c6
-rw-r--r--arch/avr32/boards/atstk1000/atstk1004.c6
-rw-r--r--arch/avr32/boards/favr-32/setup.c9
-rw-r--r--arch/avr32/boards/hammerhead/flash.c5
-rw-r--r--arch/avr32/boards/hammerhead/setup.c6
-rw-r--r--arch/avr32/boards/merisc/Kconfig5
-rw-r--r--arch/avr32/boards/merisc/Makefile1
-rw-r--r--arch/avr32/boards/merisc/display.c65
-rw-r--r--arch/avr32/boards/merisc/flash.c139
-rw-r--r--arch/avr32/boards/merisc/merisc.h18
-rw-r--r--arch/avr32/boards/merisc/merisc_sysfs.c65
-rw-r--r--arch/avr32/boards/merisc/setup.c297
-rw-r--r--arch/avr32/boards/mimc200/setup.c8
16 files changed, 651 insertions, 42 deletions
diff --git a/arch/avr32/boards/atngw100/evklcd10x.c b/arch/avr32/boards/atngw100/evklcd10x.c
index 8140b22b346..00337112c5a 100644
--- a/arch/avr32/boards/atngw100/evklcd10x.c
+++ b/arch/avr32/boards/atngw100/evklcd10x.c
@@ -11,6 +11,7 @@
#include <linux/init.h>
#include <linux/linkage.h>
+#include <linux/gpio.h>
#include <linux/fb.h>
#include <linux/platform_device.h>
@@ -19,26 +20,26 @@
#include <asm/setup.h>
#include <mach/at32ap700x.h>
+#include <mach/portmux.h>
#include <mach/board.h>
+#include <sound/atmel-ac97c.h>
+
static struct ac97c_platform_data __initdata ac97c0_data = {
- .dma_rx_periph_id = 3,
- .dma_tx_periph_id = 4,
- .dma_controller_id = 0,
- .reset_pin = GPIO_PIN_PB(19),
+ .reset_pin = GPIO_PIN_PB(19),
};
#ifdef CONFIG_BOARD_ATNGW100_EVKLCD10X_VGA
static struct fb_videomode __initdata tcg057vglad_modes[] = {
{
- .name = "640x480 @ 60",
- .refresh = 60,
+ .name = "640x480 @ 50",
+ .refresh = 50,
.xres = 640, .yres = 480,
.pixclock = KHZ2PICOS(25180),
- .left_margin = 64, .right_margin = 31,
- .upper_margin = 34, .lower_margin = 2,
- .hsync_len = 96, .vsync_len = 4,
+ .left_margin = 64, .right_margin = 96,
+ .upper_margin = 34, .lower_margin = 11,
+ .hsync_len = 64, .vsync_len = 15,
.sync = 0,
.vmode = FB_VMODE_NONINTERLACED,
@@ -69,14 +70,14 @@ static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
#elif CONFIG_BOARD_ATNGW100_EVKLCD10X_QVGA
static struct fb_videomode __initdata tcg057qvlad_modes[] = {
{
- .name = "320x240 @ 60",
- .refresh = 60,
+ .name = "320x240 @ 50",
+ .refresh = 50,
.xres = 320, .yres = 240,
.pixclock = KHZ2PICOS(6300),
- .left_margin = 52, .right_margin = 28,
- .upper_margin = 7, .lower_margin = 2,
- .hsync_len = 96, .vsync_len = 4,
+ .left_margin = 34, .right_margin = 46,
+ .upper_margin = 7, .lower_margin = 15,
+ .hsync_len = 64, .vsync_len = 12,
.sync = 0,
.vmode = FB_VMODE_NONINTERLACED,
@@ -144,12 +145,29 @@ static struct atmel_lcdfb_info __initdata atevklcd10x_lcdc_data = {
};
#endif
+static void atevklcd10x_lcdc_power_control(int on)
+{
+ gpio_set_value(GPIO_PIN_PB(15), on);
+}
+
static int __init atevklcd10x_init(void)
{
- at32_add_device_ac97c(0, &ac97c0_data);
+ /* PB15 is connected to the enable line on the boost regulator
+ * controlling the backlight for the LCD panel.
+ */
+ at32_select_gpio(GPIO_PIN_PB(15), AT32_GPIOF_OUTPUT);
+ gpio_request(GPIO_PIN_PB(15), "backlight");
+ gpio_direction_output(GPIO_PIN_PB(15), 0);
+
+ atevklcd10x_lcdc_data.atmel_lcdfb_power_control =
+ atevklcd10x_lcdc_power_control;
at32_add_device_lcdc(0, &atevklcd10x_lcdc_data,
- fbmem_start, fbmem_size, 1);
+ fbmem_start, fbmem_size,
+ ATMEL_LCDC_ALT_18BIT | ATMEL_LCDC_PE_DVAL);
+
+ at32_add_device_ac97c(0, &ac97c0_data, AC97C_BOTH);
+
return 0;
}
postcore_initcall(atevklcd10x_init);
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index 05d3722fff1..5b022aad4bd 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -56,13 +56,8 @@ static struct spi_board_info spi0_board_info[] __initdata = {
static struct mci_platform_data __initdata mci0_data = {
.slot[0] = {
.bus_width = 4,
-#ifndef CONFIG_BOARD_ATNGW100_EVKLCD10X
.detect_pin = GPIO_PIN_PC(25),
.wp_pin = GPIO_PIN_PE(0),
-#else
- .detect_pin = GPIO_PIN_NONE,
- .wp_pin = GPIO_PIN_NONE,
-#endif
},
};
@@ -123,7 +118,7 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
- at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */
+ at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_setup_serial_console(0);
}
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 1f33a106905..2adc261c9e3 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -252,12 +252,12 @@ static void __init atstk1002_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
- at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
+ at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
- at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
+ at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
- at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
+ at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c
index b3a23c88bcf..ff7e2329882 100644
--- a/arch/avr32/boards/atstk1000/atstk1003.c
+++ b/arch/avr32/boards/atstk1000/atstk1003.c
@@ -115,12 +115,12 @@ static void __init atstk1003_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
- at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
+ at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
- at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
+ at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
- at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
+ at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c
index 29b35aca96c..69a9f0f08c6 100644
--- a/arch/avr32/boards/atstk1000/atstk1004.c
+++ b/arch/avr32/boards/atstk1000/atstk1004.c
@@ -120,12 +120,12 @@ static void __init atstk1004_setup_extdac(void)
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
- at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
+ at32_map_usart(0, 1, 0); /* USART 0/B: /dev/ttyS1, IRDA */
#else
- at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
+ at32_map_usart(1, 0, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
- at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
+ at32_map_usart(3, 2, 0); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
diff --git a/arch/avr32/boards/favr-32/setup.c b/arch/avr32/boards/favr-32/setup.c
index 745c408c2ac..46c9b0a224c 100644
--- a/arch/avr32/boards/favr-32/setup.c
+++ b/arch/avr32/boards/favr-32/setup.c
@@ -22,6 +22,8 @@
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <sound/atmel-abdac.h>
+
#include <video/atmel_lcdc.h>
#include <asm/setup.h>
@@ -41,6 +43,9 @@ unsigned long at32_board_osc_rates[3] = {
/* Initialized by bootloader-specific startup code. */
struct tag *bootloader_tags __initdata;
+static struct atmel_abdac_pdata __initdata abdac0_data = {
+};
+
struct eth_addr {
u8 addr[6];
};
@@ -245,7 +250,7 @@ static void __init favr32_setup_atmel_pwm_bl(void)
void __init setup_board(void)
{
- at32_map_usart(3, 0); /* USART 3 => /dev/ttyS0 */
+ at32_map_usart(3, 0, 0); /* USART 3 => /dev/ttyS0 */
at32_setup_serial_console(0);
}
@@ -326,7 +331,7 @@ static int __init favr32_init(void)
spi1_board_info[0].irq = gpio_to_irq(GPIO_PIN_PB(3));
- set_abdac_rate(at32_add_device_abdac(0));
+ set_abdac_rate(at32_add_device_abdac(0, &abdac0_data));
at32_add_device_pwm(1 << atmel_pwm_bl_pdata.pwm_channel);
at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
diff --git a/arch/avr32/boards/hammerhead/flash.c b/arch/avr32/boards/hammerhead/flash.c
index a98c6dd3a02..776c3cb9b6e 100644
--- a/arch/avr32/boards/hammerhead/flash.c
+++ b/arch/avr32/boards/hammerhead/flash.c
@@ -15,7 +15,6 @@
#include <linux/mtd/physmap.h>
#include <linux/usb/isp116x.h>
#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
#include <linux/delay.h>
#include <mach/portmux.h>
@@ -281,13 +280,13 @@ static struct resource hh_fpga0_resource[] = {
},
};
-static u64 hh_fpga0_dma_mask = DMA_32BIT_MASK;
+static u64 hh_fpga0_dma_mask = DMA_BIT_MASK(32);
static struct platform_device hh_fpga0_device = {
.name = "hh_fpga",
.id = 0,
.dev = {
.dma_mask = &hh_fpga0_dma_mask,
- .coherent_dma_mask = DMA_32BIT_MASK,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
},
.resource = hh_fpga0_resource,
.num_resources = ARRAY_SIZE(hh_fpga0_resource),
diff --git a/arch/avr32/boards/hammerhead/setup.c b/arch/avr32/boards/hammerhead/setup.c
index 4d2fe82b202..dd009875a40 100644
--- a/arch/avr32/boards/hammerhead/setup.c
+++ b/arch/avr32/boards/hammerhead/setup.c
@@ -29,6 +29,8 @@
#include <mach/init.h>
#include <mach/portmux.h>
+#include <sound/atmel-ac97c.h>
+
#include "../../mach-at32ap/clock.h"
#include "flash.h"
@@ -163,7 +165,7 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
- at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */
+ at32_map_usart(1, 0, 0); /* USART 1: /dev/ttyS0, DB9 */
at32_setup_serial_console(0);
}
@@ -233,7 +235,7 @@ static int __init hammerhead_init(void)
i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
#ifdef CONFIG_BOARD_HAMMERHEAD_SND
- at32_add_device_ac97c(0, &ac97c_data);
+ at32_add_device_ac97c(0, &ac97c_data, AC97C_BOTH);
#endif
/* Select the Touchscreen interrupt pin mode */
diff --git a/arch/avr32/boards/merisc/Kconfig b/arch/avr32/boards/merisc/Kconfig
new file mode 100644
index 00000000000..7e043275d5a
--- /dev/null
+++ b/arch/avr32/boards/merisc/Kconfig
@@ -0,0 +1,5 @@
+# Merisc customization
+
+if BOARD_MERISC
+
+endif # BOARD_MERISC
diff --git a/arch/avr32/boards/merisc/Makefile b/arch/avr32/boards/merisc/Makefile
new file mode 100644
index 00000000000..d24c78729bd
--- /dev/null
+++ b/arch/avr32/boards/merisc/Makefile
@@ -0,0 +1 @@
+obj-y += setup.o flash.o display.o merisc_sysfs.o
diff --git a/arch/avr32/boards/merisc/display.c b/arch/avr32/boards/merisc/display.c
new file mode 100644
index 00000000000..85a543cd4ab
--- /dev/null
+++ b/arch/avr32/boards/merisc/display.c
@@ -0,0 +1,65 @@
+/*
+ * Display setup code for the Merisc board
+ *
+ * Copyright (C) 2008 Martinsson Elektronik AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/fb.h>
+#include <video/atmel_lcdc.h>
+#include <asm/setup.h>
+#include <mach/board.h>
+#include "merisc.h"
+
+static struct fb_videomode merisc_fb_videomode[] = {
+ {
+ .refresh = 44,
+ .xres = 640,
+ .yres = 480,
+ .left_margin = 96,
+ .right_margin = 96,
+ .upper_margin = 34,
+ .lower_margin = 8,
+ .hsync_len = 64,
+ .vsync_len = 64,
+ .name = "640x480 @ 44",
+ .pixclock = KHZ2PICOS(25180),
+ .sync = 0,
+ .vmode = FB_VMODE_NONINTERLACED,
+ },
+};
+
+static struct fb_monspecs merisc_fb_monspecs = {
+ .manufacturer = "Kyo",
+ .monitor = "TCG075VG2AD",
+ .modedb = merisc_fb_videomode,
+ .modedb_len = ARRAY_SIZE(merisc_fb_videomode),
+ .hfmin = 30000,
+ .hfmax = 33333,
+ .vfmin = 60,
+ .vfmax = 90,
+ .dclkmax = 30000000,
+};
+
+struct atmel_lcdfb_info merisc_lcdc_data = {
+ .default_bpp = 24,
+ .default_dmacon = ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+ .default_lcdcon2 = (ATMEL_LCDC_DISTYPE_TFT
+ | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+ | ATMEL_LCDC_MEMOR_BIG),
+ .default_monspecs = &merisc_fb_monspecs,
+ .guard_time = 2,
+};
+
+static int __init merisc_display_init(void)
+{
+ at32_add_device_lcdc(0, &merisc_lcdc_data, fbmem_start,
+ fbmem_size, 0);
+
+ return 0;
+}
+device_initcall(merisc_display_init);
diff --git a/arch/avr32/boards/merisc/flash.c b/arch/avr32/boards/merisc/flash.c
new file mode 100644
index 00000000000..8e856fd6f01
--- /dev/null
+++ b/arch/avr32/boards/merisc/flash.c
@@ -0,0 +1,139 @@
+/*
+ * Merisc board-specific flash initialization
+ *
+ * Copyright (C) 2008 Martinsson Elektronik AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <mach/smc.h>
+
+/* Will be translated to units of 14.3 ns, rounded up */
+static struct smc_timing flash_timing __initdata = {
+ .ncs_read_setup = 1 * 14,
+ .nrd_setup = 5 * 14,
+ .ncs_write_setup = 1 * 14,
+ .nwe_setup = 2 * 14,
+
+ .ncs_read_pulse = 12 * 14,
+ .nrd_pulse = 7 * 14,
+ .ncs_write_pulse = 8 * 14,
+ .nwe_pulse = 4 * 14,
+
+ .read_cycle = 14 * 14,
+ .write_cycle = 10 * 14,
+};
+
+static struct smc_config flash_config __initdata = {
+ .bus_width = 2,
+ .nrd_controlled = 1,
+ .nwe_controlled = 1,
+ .byte_write = 1,
+ .tdf_cycles = 3,
+};
+
+static struct mtd_partition flash_0_parts[] = {
+ {
+ .name = "boot",
+ .offset = 0x00000000,
+ .size = 0x00060000,
+ .mask_flags = 0,
+ },
+ {
+ .name = "kernel",
+ .offset = 0x00060000,
+ .size = 0x00200000,
+ .mask_flags = 0,
+ },
+ {
+ .name = "root",
+ .offset = 0x00260000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ },
+};
+
+static struct mtd_partition flash_1_parts[] = {
+ {
+ .name = "2ndflash",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0,
+ },
+};
+
+static struct physmap_flash_data flash_data[] = {
+ {
+ .width = 2,
+ .nr_parts = ARRAY_SIZE(flash_0_parts),
+ .parts = flash_0_parts,
+ },
+ {
+ .width = 2,
+ .nr_parts = ARRAY_SIZE(flash_1_parts),
+ .parts = flash_1_parts,
+ }
+};
+
+static struct resource flash_resource[] = {
+ {
+ .start = 0x00000000,
+ .end = 0x03ffffff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x04000000,
+ .end = 0x07ffffff,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device flash_device[] = {
+ {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &flash_resource[0],
+ .num_resources = 1,
+ .dev = {
+ .platform_data = &flash_data[0],
+ },
+ },
+ {
+ .name = "physmap-flash",
+ .id = 1,
+ .resource = &flash_resource[1],
+ .num_resources = 1,
+ .dev = {
+ .platform_data = &flash_data[1],
+ },
+ },
+};
+
+static int __init merisc_flash_init(void)
+{
+ int ret;
+ smc_set_timing(&flash_config, &flash_timing);
+
+ ret = smc_set_configuration(0, &flash_config);
+ if (ret < 0) {
+ printk(KERN_ERR "Merisc: failed to set NOR flash timing #0\n");
+ return ret;
+ }
+
+ ret = smc_set_configuration(4, &flash_config);
+ if (ret < 0) {
+ printk(KERN_ERR "Merisc: failed to set NOR flash timing #1\n");
+ return ret;
+ }
+
+ platform_device_register(&flash_device[0]);
+ platform_device_register(&flash_device[1]);
+ return 0;
+}
+device_initcall(merisc_flash_init);
diff --git a/arch/avr32/boards/merisc/merisc.h b/arch/avr32/boards/merisc/merisc.h
new file mode 100644
index 00000000000..50ffb2f3fcb
--- /dev/null
+++ b/arch/avr32/boards/merisc/merisc.h
@@ -0,0 +1,18 @@
+/*
+ * Merisc exports
+ *
+ * Copyright (C) 2008 Martinsson Elektronik AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ARCH_AVR32_BOARDS_MERISC_MERISC_H
+#define __ARCH_AVR32_BOARDS_MERISC_MERISC_H
+
+const char *merisc_revision(void);
+const char *merisc_model(void);
+
+extern struct class merisc_class;
+
+#endif /* __ARCH_AVR32_BOARDS_MERISC_MERISC_H */
diff --git a/arch/avr32/boards/merisc/merisc_sysfs.c b/arch/avr32/boards/merisc/merisc_sysfs.c
new file mode 100644
index 00000000000..df431fdba9a
--- /dev/null
+++ b/arch/avr32/boards/merisc/merisc_sysfs.c
@@ -0,0 +1,65 @@
+/*
+ * Merisc sysfs exports
+ *
+ * Copyright (C) 2008 Martinsson Elektronik AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/spinlock.h>
+#include <linux/device.h>
+#include <linux/sysdev.h>
+#include <linux/timer.h>
+#include <linux/err.h>
+#include <linux/ctype.h>
+#include "merisc.h"
+
+static ssize_t merisc_model_show(struct class *class, char *buf)
+{
+ ssize_t ret = 0;
+
+ sprintf(buf, "%s\n", merisc_model());
+ ret = strlen(buf) + 1;
+
+ return ret;
+}
+
+static ssize_t merisc_revision_show(struct class *class, char *buf)
+{
+ ssize_t ret = 0;
+
+ sprintf(buf, "%s\n", merisc_revision());
+ ret = strlen(buf) + 1;
+
+ return ret;
+}
+
+static struct class_attribute merisc_class_attrs[] = {
+ __ATTR(model, S_IRUGO, merisc_model_show, NULL),
+ __ATTR(revision, S_IRUGO, merisc_revision_show, NULL),
+ __ATTR_NULL,
+};
+
+struct class merisc_class = {
+ .name = "merisc",
+ .owner = THIS_MODULE,
+ .class_attrs = merisc_class_attrs,
+};
+
+static int __init merisc_sysfs_init(void)
+{
+ int status;
+
+ status = class_register(&merisc_class);
+ if (status < 0)
+ return status;
+
+ return 0;
+}
+
+postcore_initcall(merisc_sysfs_init);
diff --git a/arch/avr32/boards/merisc/setup.c b/arch/avr32/boards/merisc/setup.c
new file mode 100644
index 00000000000..20b300cf105
--- /dev/null
+++ b/arch/avr32/boards/merisc/setup.c
@@ -0,0 +1,297 @@
+/*
+ * Board-specific setup code for the Merisc
+ *
+ * Copyright (C) 2008 Martinsson Elektronik AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/etherdevice.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/linkage.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/irq.h>
+#include <linux/fb.h>
+#include <linux/atmel-mci.h>
+
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/gpio.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+#include "merisc.h"
+
+/* Holds the autodetected board model and revision */
+static int merisc_board_id;
+
+/* Initialized by bootloader-specific startup code. */
+struct tag *bootloader_tags __initdata;
+
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+ [0] = 32768, /* 32.768 kHz on RTC osc */
+ [1] = 20000000, /* 20 MHz on osc0 */
+ [2] = 12000000, /* 12 MHz on osc1 */
+};
+
+struct eth_addr {
+ u8 addr[6];
+};
+
+static struct eth_addr __initdata hw_addr[2];
+static struct eth_platform_data __initdata eth_data[2];
+
+static int ads7846_get_pendown_state_PB26(void)
+{
+ return !gpio_get_value(GPIO_PIN_PB(26));
+}
+
+static int ads7846_get_pendown_state_PB28(void)
+{
+ return !gpio_get_value(GPIO_PIN_PB(28));
+}
+
+static struct ads7846_platform_data __initdata ads7846_data = {
+ .model = 7846,
+ .vref_delay_usecs = 100,
+ .vref_mv = 0,
+ .keep_vref_on = 0,
+ .settle_delay_usecs = 150,
+ .penirq_recheck_delay_usecs = 1,
+ .x_plate_ohms = 800,
+ .debounce_rep = 4,
+ .debounce_max = 10,
+ .debounce_tol = 50,
+ .get_pendown_state = ads7846_get_pendown_state_PB26,
+ .filter_init = NULL,
+ .filter = NULL,
+ .filter_cleanup = NULL,
+};
+
+static struct spi_board_info __initdata spi0_board_info[] = {
+ {
+ .modalias = "ads7846",
+ .max_speed_hz = 3250000,
+ .chip_select = 0,
+ .bus_num = 0,
+ .platform_data = &ads7846_data,
+ .mode = SPI_MODE_0,
+ },
+};
+
+static struct mci_platform_data __initdata mci0_data = {
+ .slot[0] = {
+ .bus_width = 4,
+ .detect_pin = GPIO_PIN_PE(19),
+ .wp_pin = GPIO_PIN_PE(20),
+ },
+};
+
+static int __init parse_tag_ethernet(struct tag *tag)
+{
+ int i;
+
+ i = tag->u.ethernet.mac_index;
+ if (i < ARRAY_SIZE(hw_addr)) {
+ memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
+ sizeof(hw_addr[i].addr));
+ }
+
+ return 0;
+}
+__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
+
+static void __init set_hw_addr(struct platform_device *pdev)
+{
+ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ const u8 *addr;
+ void __iomem *regs;
+ struct clk *pclk;
+
+ if (!res)
+ return;
+
+ if (pdev->id >= ARRAY_SIZE(hw_addr))
+ return;
+
+ addr = hw_addr[pdev->id].addr;
+ if (!is_valid_ether_addr(addr))
+ return;
+
+ regs = (void __iomem __force *)res->start;
+ pclk = clk_get(&pdev->dev, "pclk");
+ if (!pclk)
+ return;
+
+ clk_enable(pclk);
+ __raw_writel((addr[3] << 24) | (addr[2] << 16)
+ | (addr[1] << 8) | addr[0], regs + 0x98);
+ __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
+ clk_disable(pclk);
+ clk_put(pclk);
+}
+
+static struct i2c_gpio_platform_data i2c_gpio_data = {
+ .sda_pin = GPIO_PIN_PA(6),
+ .scl_pin = GPIO_PIN_PA(7),
+ .sda_is_open_drain = 1,
+ .scl_is_open_drain = 1,
+ .udelay = 2,
+};
+
+static struct platform_device i2c_gpio_device = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &i2c_gpio_data,
+ },
+};
+
+static struct i2c_board_info __initdata i2c_info[] = {
+ {
+ I2C_BOARD_INFO("pcf8563", 0x51)
+ },
+};
+
+#ifdef CONFIG_LEDS_ATMEL_PWM
+static struct gpio_led stk_pwm_led[] = {
+ {
+ .name = "backlight",
+ .gpio = 0, /* PWM channel 0 (LCD backlight) */
+ },
+};
+
+static struct gpio_led_platform_data stk_pwm_led_data = {
+ .num_leds = ARRAY_SIZE(stk_pwm_led),
+ .leds = stk_pwm_led,
+};
+
+static struct platform_device stk_pwm_led_dev = {
+ .name = "leds-atmel-pwm",
+ .id = -1,
+ .dev = {
+ .platform_data = &stk_pwm_led_data,
+ },
+};
+#endif
+
+const char *merisc_model(void)
+{
+ switch (merisc_board_id) {
+ case 0:
+ case 1:
+ return "500-01";
+ case 2:
+ return "BT";
+ default:
+ return "Unknown";
+ }
+}
+
+const char *merisc_revision(void)
+{
+ switch (merisc_board_id) {
+ case 0:
+ return "B";
+ case 1:
+ return "D";
+ case 2:
+ return "A";
+ default:
+ return "Unknown";
+ }
+}
+
+static void detect_merisc_board_id(void)
+{
+ /* Board ID pins MUST be set as input or the board may be damaged */
+ at32_select_gpio(GPIO_PIN_PA(24), AT32_GPIOF_PULLUP);
+ at32_select_gpio(GPIO_PIN_PA(25), AT32_GPIOF_PULLUP);
+ at32_select_gpio(GPIO_PIN_PA(26), AT32_GPIOF_PULLUP);
+ at32_select_gpio(GPIO_PIN_PA(27), AT32_GPIOF_PULLUP);
+
+ merisc_board_id = !gpio_get_value(GPIO_PIN_PA(24)) +
+ !gpio_get_value(GPIO_PIN_PA(25)) * 2 +
+ !gpio_get_value(GPIO_PIN_PA(26)) * 4 +
+ !gpio_get_value(GPIO_PIN_PA(27)) * 8;
+}
+
+void __init setup_board(void)
+{
+ at32_map_usart(0, 0, 0);
+ at32_map_usart(1, 1, 0);
+ at32_map_usart(3, 3, 0);
+ at32_setup_serial_console(1);
+}
+
+static int __init merisc_init(void)
+{
+ detect_merisc_board_id();
+
+ printk(KERN_NOTICE "BOARD: Merisc %s revision %s\n", merisc_model(),
+ merisc_revision());
+
+ /* Reserve pins for SDRAM */
+ at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL | (1 << 26));
+
+ if (merisc_board_id >= 1)
+ at32_map_usart(2, 2, 0);
+
+ at32_add_device_usart(0);
+ at32_add_device_usart(1);
+ if (merisc_board_id >= 1)
+ at32_add_device_usart(2);
+ at32_add_device_usart(3);
+ set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
+
+ /* ADS7846 PENIRQ */
+ if (merisc_board_id == 0) {
+ ads7846_data.get_pendown_state = ads7846_get_pendown_state_PB26;
+ at32_select_periph(GPIO_PIOB_BASE, 1 << 26,
+ GPIO_PERIPH_A, AT32_GPIOF_PULLUP);
+ spi0_board_info[0].irq = AT32_EXTINT(1);
+ } else {
+ ads7846_data.get_pendown_state = ads7846_get_pendown_state_PB28;
+ at32_select_periph(GPIO_PIOB_BASE, 1 << 28, GPIO_PERIPH_A,
+ AT32_GPIOF_PULLUP);
+ spi0_board_info[0].irq = AT32_EXTINT(3);
+ }
+
+ /* ADS7846 busy pin */
+ at32_select_gpio(GPIO_PIN_PA(4), AT32_GPIOF_PULLUP);
+
+ at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+
+ at32_add_device_mci(0, &mci0_data);
+
+#ifdef CONFIG_LEDS_ATMEL_PWM
+ at32_add_device_pwm((1 << 0) | (1 << 2));
+ platform_device_register(&stk_pwm_led_dev);
+#else
+ at32_add_device_pwm((1 << 2));
+#endif
+
+ at32_select_gpio(i2c_gpio_data.sda_pin,
+ AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
+ at32_select_gpio(i2c_gpio_data.scl_pin,
+ AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
+ platform_device_register(&i2c_gpio_device);
+
+ i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
+
+ return 0;
+}
+postcore_initcall(merisc_init);
diff --git a/arch/avr32/boards/mimc200/setup.c b/arch/avr32/boards/mimc200/setup.c
index 2b58d61f0af..c1b2175b4fe 100644
--- a/arch/avr32/boards/mimc200/setup.c
+++ b/arch/avr32/boards/mimc200/setup.c
@@ -175,10 +175,10 @@ static void __init set_hw_addr(struct platform_device *pdev)
void __init setup_board(void)
{
- at32_map_usart(0, 0); /* USART 0: /dev/ttyS0 (TTL --> Altera) */
- at32_map_usart(1, 1); /* USART 1: /dev/ttyS1 (RS232) */
- at32_map_usart(2, 2); /* USART 2: /dev/ttyS2 (RS485) */
- at32_map_usart(3, 3); /* USART 3: /dev/ttyS3 (RS422 Multidrop) */
+ at32_map_usart(0, 0, 0); /* USART 0: /dev/ttyS0 (TTL --> Altera) */
+ at32_map_usart(1, 1, 0); /* USART 1: /dev/ttyS1 (RS232) */
+ at32_map_usart(2, 2, 0); /* USART 2: /dev/ttyS2 (RS485) */
+ at32_map_usart(3, 3, 0); /* USART 3: /dev/ttyS3 (RS422 Multidrop) */
}
static struct i2c_gpio_platform_data i2c_gpio_data = {
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-26 08:46:39 +0000