diff options
Diffstat (limited to 'arch/avr32/boards')
| -rw-r--r-- | arch/avr32/boards/atngw100/Makefile | 1 | ||||
| -rw-r--r-- | arch/avr32/boards/atngw100/flash.c | 95 | ||||
| -rw-r--r-- | arch/avr32/boards/atngw100/setup.c | 124 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 4 | ||||
| -rw-r--r-- | arch/avr32/boards/atstk1000/setup.c | 30 |
5 files changed, 223 insertions, 31 deletions
diff --git a/arch/avr32/boards/atngw100/Makefile b/arch/avr32/boards/atngw100/Makefile new file mode 100644 index 00000000000..c740aa11675 --- /dev/null +++ b/arch/avr32/boards/atngw100/Makefile @@ -0,0 +1 @@ +obj-y += setup.o flash.o diff --git a/arch/avr32/boards/atngw100/flash.c b/arch/avr32/boards/atngw100/flash.c new file mode 100644 index 00000000000..f9b32a8eab9 --- /dev/null +++ b/arch/avr32/boards/atngw100/flash.c @@ -0,0 +1,95 @@ +/* + * ATNGW100 board-specific flash initialization + * + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> + +#include <asm/arch/smc.h> + +static struct smc_config flash_config __initdata = { + .ncs_read_setup = 0, + .nrd_setup = 40, + .ncs_write_setup = 0, + .nwe_setup = 10, + + .ncs_read_pulse = 80, + .nrd_pulse = 40, + .ncs_write_pulse = 65, + .nwe_pulse = 55, + + .read_cycle = 120, + .write_cycle = 120, + + .bus_width = 2, + .nrd_controlled = 1, + .nwe_controlled = 1, + .byte_write = 1, +}; + +static struct mtd_partition flash_parts[] = { + { + .name = "u-boot", + .offset = 0x00000000, + .size = 0x00020000, /* 128 KiB */ + .mask_flags = MTD_WRITEABLE, + }, + { + .name = "root", + .offset = 0x00020000, + .size = 0x007d0000, + }, + { + .name = "env", + .offset = 0x007f0000, + .size = 0x00010000, + .mask_flags = MTD_WRITEABLE, + }, +}; + +static struct physmap_flash_data flash_data = { + .width = 2, + .nr_parts = ARRAY_SIZE(flash_parts), + .parts = flash_parts, +}; + +static struct resource flash_resource = { + .start = 0x00000000, + .end = 0x007fffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device flash_device = { + .name = "physmap-flash", + .id = 0, + .resource = &flash_resource, + .num_resources = 1, + .dev = { + .platform_data = &flash_data, + }, +}; + +/* This needs to be called after the SMC has been initialized */ +static int __init atngw100_flash_init(void) +{ + int ret; + + ret = smc_set_configuration(0, &flash_config); + if (ret < 0) { + printk(KERN_ERR "atngw100: failed to set NOR flash timing\n"); + return ret; + } + + platform_device_register(&flash_device); + + return 0; +} +device_initcall(atngw100_flash_init); diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c new file mode 100644 index 00000000000..9bc37d4f668 --- /dev/null +++ b/arch/avr32/boards/atngw100/setup.c @@ -0,0 +1,124 @@ +/* + * Board-specific setup code for the ATNGW100 Network Gateway + * + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/etherdevice.h> +#include <linux/init.h> +#include <linux/linkage.h> +#include <linux/platform_device.h> +#include <linux/types.h> +#include <linux/spi/spi.h> + +#include <asm/io.h> +#include <asm/setup.h> + +#include <asm/arch/at32ap7000.h> +#include <asm/arch/board.h> +#include <asm/arch/init.h> + +/* Initialized by bootloader-specific startup code. */ +struct tag *bootloader_tags __initdata; + +struct eth_addr { + u8 addr[6]; +}; +static struct eth_addr __initdata hw_addr[2]; +static struct eth_platform_data __initdata eth_data[2]; + +static struct spi_board_info spi0_board_info[] __initdata = { + { + .modalias = "mtd_dataflash", + .max_speed_hz = 10000000, + .chip_select = 0, + }, +}; + +/* + * The next two functions should go away as the boot loader is + * supposed to initialize the macb address registers with a valid + * ethernet address. But we need to keep it around for a while until + * we can be reasonably sure the boot loader does this. + * + * The phy_id is ignored as the driver will probe for it. + */ +static int __init parse_tag_ethernet(struct tag *tag) +{ + int i; + + i = tag->u.ethernet.mac_index; + if (i < ARRAY_SIZE(hw_addr)) + memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address, + sizeof(hw_addr[i].addr)); + + return 0; +} +__tagtable(ATAG_ETHERNET, parse_tag_ethernet); + +static void __init set_hw_addr(struct platform_device *pdev) +{ + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + const u8 *addr; + void __iomem *regs; + struct clk *pclk; + + if (!res) + return; + if (pdev->id >= ARRAY_SIZE(hw_addr)) + return; + + addr = hw_addr[pdev->id].addr; + if (!is_valid_ether_addr(addr)) + return; + + /* + * Since this is board-specific code, we'll cheat and use the + * physical address directly as we happen to know that it's + * the same as the virtual address. + */ + regs = (void __iomem __force *)res->start; + pclk = clk_get(&pdev->dev, "pclk"); + if (!pclk) + return; + + clk_enable(pclk); + __raw_writel((addr[3] << 24) | (addr[2] << 16) + | (addr[1] << 8) | addr[0], regs + 0x98); + __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c); + clk_disable(pclk); + clk_put(pclk); +} + +struct platform_device *at32_usart_map[1]; +unsigned int at32_nr_usarts = 1; + +void __init setup_board(void) +{ + at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */ + at32_setup_serial_console(0); +} + +static int __init atngw100_init(void) +{ + /* + * ATNGW100 uses 16-bit SDRAM interface, so we don't need to + * reserve any pins for it. + */ + + at32_add_system_devices(); + + at32_add_device_usart(0); + + set_hw_addr(at32_add_device_eth(0, ð_data[0])); + set_hw_addr(at32_add_device_eth(1, ð_data[1])); + + at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); + + return 0; +} +postcore_initcall(atngw100_init); diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index 5974768a59e..abe6ca203fa 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -33,7 +33,7 @@ struct eth_addr { static struct eth_addr __initdata hw_addr[2]; static struct eth_platform_data __initdata eth_data[2]; -extern struct lcdc_platform_data atstk1000_fb0_data; +static struct lcdc_platform_data atstk1000_fb0_data; static struct spi_board_info spi0_board_info[] __initdata = { { @@ -148,6 +148,8 @@ static int __init atstk1002_init(void) set_hw_addr(at32_add_device_eth(0, ð_data[0])); at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); + atstk1000_fb0_data.fbmem_start = fbmem_start; + atstk1000_fb0_data.fbmem_size = fbmem_size; at32_add_device_lcdc(0, &atstk1000_fb0_data); return 0; diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c index 272c011802a..2bc4b88d7ed 100644 --- a/arch/avr32/boards/atstk1000/setup.c +++ b/arch/avr32/boards/atstk1000/setup.c @@ -18,33 +18,3 @@ /* Initialized by bootloader-specific startup code. */ struct tag *bootloader_tags __initdata; - -struct lcdc_platform_data __initdata atstk1000_fb0_data; - -void __init board_setup_fbmem(unsigned long fbmem_start, - unsigned long fbmem_size) -{ - if (!fbmem_size) - return; - - if (!fbmem_start) { - void *fbmem; - - fbmem = alloc_bootmem_low_pages(fbmem_size); - fbmem_start = __pa(fbmem); - } else { - pg_data_t *pgdat; - - for_each_online_pgdat(pgdat) { - if (fbmem_start >= pgdat->bdata->node_boot_start - && fbmem_start <= pgdat->bdata->node_low_pfn) - reserve_bootmem_node(pgdat, fbmem_start, - fbmem_size); - } - } - - printk("%luKiB framebuffer memory at address 0x%08lx\n", - fbmem_size >> 10, fbmem_start); - atstk1000_fb0_data.fbmem_start = fbmem_start; - atstk1000_fb0_data.fbmem_size = fbmem_size; -} |