4 files changed, 51 insertions, 2 deletions

diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index a398be28496..a51bb9fb3c8 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -9,6 +9,8 @@
  */
 #include <linux/clk.h>
 #include <linux/etherdevice.h>
+#include <linux/irq.h>
+#include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
 #include <linux/init.h>
 #include <linux/linkage.h>
@@ -25,6 +27,13 @@
 #include <asm/arch/init.h>
 #include <asm/arch/portmux.h>
 
+/* Oscillator frequencies. These are board-specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
 /* Initialized by bootloader-specific startup code. */
 struct tag *bootloader_tags __initdata;
 
@@ -140,6 +149,10 @@ static struct platform_device i2c_gpio_device = {
 	},
 };
 
+static struct i2c_board_info __initdata i2c_info[] = {
+	/* NOTE:  original ATtiny24 firmware is at address 0x0b */
+};
+
 static int __init atngw100_init(void)
 {
 	unsigned	i;
@@ -165,12 +178,28 @@ static int __init atngw100_init(void)
 	}
 	platform_device_register(&ngw_gpio_leds);
 
+	/* all these i2c/smbus pins should have external pullups for
+	 * open-drain sharing among all I2C devices.  SDA and SCL do;
+	 * PB28/EXTINT3 doesn't; it should be SMBALERT# (for PMBus),
+	 * but it's not available off-board.
+	 */
+	at32_select_periph(GPIO_PIN_PB(28), 0, AT32_GPIOF_PULLUP);
 	at32_select_gpio(i2c_gpio_data.sda_pin,
 		AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
 	at32_select_gpio(i2c_gpio_data.scl_pin,
 		AT32_GPIOF_MULTIDRV | AT32_GPIOF_OUTPUT | AT32_GPIOF_HIGH);
 	platform_device_register(&i2c_gpio_device);
+	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
 
 	return 0;
 }
 postcore_initcall(atngw100_init);
+
+static int __init atngw100_arch_init(void)
+{
+	/* set_irq_type() after the arch_initcall for EIC has run, and
+	 * before the I2C subsystem could try using this IRQ.
+	 */
+	return set_irq_type(AT32_EXTINT(3), IRQ_TYPE_EDGE_FALLING);
+}
+arch_initcall(atngw100_arch_init);
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 000eb4220a1..86b363c1c25 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -28,6 +28,12 @@
 
 #include "atstk1000.h"
 
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
 
 struct eth_addr {
 	u8 addr[6];
@@ -232,7 +238,7 @@ static int __init atstk1002_init(void)
 	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
 #else
 	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
-			     fbmem_start, fbmem_size);
+			     fbmem_start, fbmem_size, 0);
 #endif
 	at32_add_device_usba(0, NULL);
 #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c
index a0b223df35a..ea109f435a8 100644
--- a/arch/avr32/boards/atstk1000/atstk1003.c
+++ b/arch/avr32/boards/atstk1000/atstk1003.c
@@ -27,6 +27,13 @@
 
 #include "atstk1000.h"
 
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
 #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
 static struct at73c213_board_info at73c213_data = {
 	.ssc_id		= 0,
diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c
index e765a8652b3..c7236df74d7 100644
--- a/arch/avr32/boards/atstk1000/atstk1004.c
+++ b/arch/avr32/boards/atstk1000/atstk1004.c
@@ -29,6 +29,13 @@
 
 #include "atstk1000.h"
 
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
 #ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
 static struct at73c213_board_info at73c213_data = {
 	.ssc_id		= 0,
@@ -133,7 +140,7 @@ static int __init atstk1004_init(void)
 	at32_add_device_mci(0);
 #endif
 	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
-			     fbmem_start, fbmem_size);
+			     fbmem_start, fbmem_size, 0);
 	at32_add_device_usba(0, NULL);
 #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
 	at32_add_device_ssc(0, ATMEL_SSC_TX);