summaryrefslogtreecommitdiffstats
path: root/arch/blackfin/mach-bf533
diff options
context:
space:
mode:
Diffstat (limited to 'arch/blackfin/mach-bf533')
-rw-r--r--arch/blackfin/mach-bf533/Kconfig92
-rw-r--r--arch/blackfin/mach-bf533/Makefile9
-rw-r--r--arch/blackfin/mach-bf533/boards/Makefile8
-rw-r--r--arch/blackfin/mach-bf533/boards/cm_bf533.c267
-rw-r--r--arch/blackfin/mach-bf533/boards/ezkit.c224
-rw-r--r--arch/blackfin/mach-bf533/boards/generic_board.c95
-rw-r--r--arch/blackfin/mach-bf533/boards/stamp.c321
-rw-r--r--arch/blackfin/mach-bf533/cpu.c161
-rw-r--r--arch/blackfin/mach-bf533/head.S774
-rw-r--r--arch/blackfin/mach-bf533/ints-priority.c65
10 files changed, 2016 insertions, 0 deletions
diff --git a/arch/blackfin/mach-bf533/Kconfig b/arch/blackfin/mach-bf533/Kconfig
new file mode 100644
index 00000000000..14297b3ed5c
--- /dev/null
+++ b/arch/blackfin/mach-bf533/Kconfig
@@ -0,0 +1,92 @@
+if (BF533 || BF532 || BF531)
+
+menu "BF533/2/1 Specific Configuration"
+
+comment "Interrupt Priority Assignment"
+menu "Priority"
+
+config UART_ERROR
+ int "UART ERROR"
+ default 7
+config SPORT0_ERROR
+ int "SPORT0 ERROR"
+ default 7
+config SPI_ERROR
+ int "SPI ERROR"
+ default 7
+config SPORT1_ERROR
+ int "SPORT1 ERROR"
+ default 7
+config PPI_ERROR
+ int "PPI ERROR"
+ default 7
+config DMA_ERROR
+ int "DMA ERROR"
+ default 7
+config PLLWAKE_ERROR
+ int "PLL WAKEUP ERROR"
+ default 7
+
+config RTC_ERROR
+ int "RTC ERROR"
+ default 8
+config DMA0_PPI
+ int "DMA0 PPI"
+ default 8
+
+config DMA1_SPORT0RX
+ int "DMA1 (SPORT0 RX)"
+ default 9
+config DMA2_SPORT0TX
+ int "DMA2 (SPORT0 TX)"
+ default 9
+config DMA3_SPORT1RX
+ int "DMA3 (SPORT1 RX)"
+ default 9
+config DMA4_SPORT1TX
+ int "DMA4 (SPORT1 TX)"
+ default 9
+config DMA5_SPI
+ int "DMA5 (SPI)"
+ default 10
+config DMA6_UARTRX
+ int "DMA6 (UART0 RX)"
+ default 10
+config DMA7_UARTTX
+ int "DMA7 (UART0 TX)"
+ default 10
+config TIMER0
+ int "TIMER0"
+ default 11
+config TIMER1
+ int "TIMER1"
+ default 11
+config TIMER2
+ int "TIMER2"
+ default 11
+config PFA
+ int "PF Interrupt A"
+ default 12
+config PFB
+ int "PF Interrupt B"
+ default 12
+config MEMDMA0
+ int "MEMORY DMA0"
+ default 13
+config MEMDMA1
+ int "MEMORY DMA1"
+ default 13
+config WDTIMER
+ int "WATCH DOG TIMER"
+ default 13
+
+ help
+ Enter the priority numbers between 7-13 ONLY. Others are Reserved.
+ This applies to all the above. It is not recommended to assign the
+ highest priority number 7 to UART or any other device.
+
+endmenu
+
+endmenu
+
+endif
diff --git a/arch/blackfin/mach-bf533/Makefile b/arch/blackfin/mach-bf533/Makefile
new file mode 100644
index 00000000000..76d2c2b8579
--- /dev/null
+++ b/arch/blackfin/mach-bf533/Makefile
@@ -0,0 +1,9 @@
+#
+# arch/blackfin/mach-bf533/Makefile
+#
+
+extra-y := head.o
+
+obj-y := ints-priority.o
+
+obj-$(CONFIG_CPU_FREQ_BF533) += cpu.o
diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile
new file mode 100644
index 00000000000..12a631ab389
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/Makefile
@@ -0,0 +1,8 @@
+#
+# arch/blackfin/mach-bf533/boards/Makefile
+#
+
+obj-$(CONFIG_GENERIC_BOARD) += generic_board.o
+obj-$(CONFIG_BFIN533_STAMP) += stamp.o
+obj-$(CONFIG_BFIN533_EZKIT) += ezkit.o
+obj-$(CONFIG_BFIN533_BLUETECHNIX_CM) += cm_bf533.o
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
new file mode 100644
index 00000000000..23a7f607df3
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -0,0 +1,267 @@
+/*
+ * File: arch/blackfin/mach-bf533/boards/cm_bf533.c
+ * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author: Aidan Williams <aidan@nicta.com.au> Copright 2005
+ *
+ * Created: 2005
+ * Description: Board description file
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/usb_isp1362.h>
+#include <asm/irq.h>
+#include <asm/bfin5xx_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "Bluetechnix CM BF533";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ },{
+ .name = "kernel",
+ .size = 0xe0000,
+ .offset = 0x20000
+ },{
+ .name = "file system",
+ .size = 0x700000,
+ .offset = 0x00100000,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 1, /* use dma transfer with this chip*/
+ .bits_per_word = 16,
+};
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },{
+ .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 2, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ },
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836-spi",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master spi_bfin_master_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+};
+
+static struct platform_device spi_bfin_master_device = {
+ .name = "bfin-spi-master",
+ .id = 1, /* Bus number */
+ .dev = {
+ .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+ {
+ .start = 0x20200300,
+ .end = 0x20200300 + 16,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PF0,
+ .end = IRQ_PF0,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device bfin_uart_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart_resources),
+ .resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+ {
+ .start = 0x20308000,
+ .end = 0x20308000,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = 0x20308004,
+ .end = 0x20308004,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PF4,
+ .end = IRQ_PF4,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+ .sel15Kres = 1,
+ .clknotstop = 0,
+ .oc_enable = 0,
+ .int_act_high = 0,
+ .int_edge_triggered = 0,
+ .remote_wakeup_connected = 0,
+ .no_power_switching = 1,
+ .power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+ .name = "isp1362-hcd",
+ .id = 0,
+ .dev = {
+ .platform_data = &isp1362_priv,
+ },
+ .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+ .resource = isp1362_hcd_resources,
+};
+#endif
+
+static struct platform_device *cm_bf533_devices[] __initdata = {
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+ &bfin_uart_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+ &bfin_sport0_uart_device,
+ &bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+ &isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &spi_bfin_master_device,
+#endif
+};
+
+static int __init cm_bf533_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ platform_add_devices(cm_bf533_devices, ARRAY_SIZE(cm_bf533_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+ return 0;
+}
+
+arch_initcall(cm_bf533_init);
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
new file mode 100644
index 00000000000..747298ea907
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -0,0 +1,224 @@
+/*
+ * File: arch/blackfin/mach-bf533/ezkit.c
+ * Based on: Orginal Work
+ * Author: Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created: 2005
+ * Description:
+ *
+ * Modified: Robin Getz <rgetz@blackfin.uclinux.org> - Named the boards
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/usb_isp1362.h>
+#include <asm/irq.h>
+#include <asm/bfin5xx_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "ADDS-BF533-EZKIT";
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+/*
+ * USB-LAN EzExtender board
+ * Driver needs to know address, irq and flag pin.
+ */
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+ {
+ .name = "smc91x-regs",
+ .start = 0x20310300,
+ .end = 0x20310300 + 16,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PF9,
+ .end = IRQ_PF9,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ },{
+ .name = "kernel",
+ .size = 0xe0000,
+ .offset = 0x20000
+ },{
+ .name = "file system",
+ .size = 0x700000,
+ .offset = 0x00100000,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 1, /* use dma transfer with this chip*/
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+ {
+ .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836-spi",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master spi_bfin_master_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+};
+
+static struct platform_device spi_bfin_master_device = {
+ .name = "bfin-spi-master",
+ .id = 1, /* Bus number */
+ .dev = {
+ .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device bfin_uart_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart_resources),
+ .resource = bfin_uart_resources,
+};
+#endif
+
+static struct platform_device *ezkit_devices[] __initdata = {
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &spi_bfin_master_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+ &bfin_uart_device,
+#endif
+};
+
+static int __init ezkit_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+ return 0;
+}
+
+arch_initcall(ezkit_init);
diff --git a/arch/blackfin/mach-bf533/boards/generic_board.c b/arch/blackfin/mach-bf533/boards/generic_board.c
new file mode 100644
index 00000000000..c0f43ccfbfb
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/generic_board.c
@@ -0,0 +1,95 @@
+/*
+ * File: arch/blackfin/mach-bf533/generic_board.c
+ * Based on: arch/blackfin/mach-bf533/ezkit.c
+ * Author: Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created: 2005
+ * Description:
+ *
+ * Modified:
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/irq.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "UNKNOWN BOARD";
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+ {
+ .start = 0x20300300,
+ .end = 0x20300300 + 16,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PROG_INTB,
+ .end = IRQ_PROG_INTB,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },{
+ /*
+ * denotes the flag pin and is used directly if
+ * CONFIG_IRQCHIP_DEMUX_GPIO is defined.
+ */
+ .start = IRQ_PF7,
+ .end = IRQ_PF7,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+};
+#endif
+
+static struct platform_device *generic_board_devices[] __initdata = {
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+};
+
+static int __init generic_board_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ return platform_add_devices(generic_board_devices, ARRAY_SIZE(generic_board_devices));
+}
+
+arch_initcall(generic_board_init);
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
new file mode 100644
index 00000000000..d7b3a5d74e8
--- /dev/null
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -0,0 +1,321 @@
+/*
+ * File: arch/blackfin/mach-bf533/stamp.c
+ * Based on: arch/blackfin/mach-bf533/ezkit.c
+ * Author: Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created: 2005
+ * Description: Board Info File for the BF533-STAMP
+ *
+ * Modified:
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb_isp1362.h>
+#endif
+#include <asm/irq.h>
+#include <asm/bfin5xx_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "ADDS-BF533-STAMP";
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+/*
+ * Driver needs to know address, irq and flag pin.
+ */
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+ {
+ .name = "smc91x-regs",
+ .start = 0x20300300,
+ .end = 0x20300300 + 16,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PF7,
+ .end = IRQ_PF7,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+ {
+ .start = 0x20300000,
+ .end = 0x20300000 + 0x100,
+ .flags = IORESOURCE_MEM,
+ },{
+ .start = IRQ_PF10,
+ .end = IRQ_PF10,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device net2272_bfin_device = {
+ .name = "net2272",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(net2272_bfin_resources),
+ .resource = net2272_bfin_resources,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ },{
+ .name = "kernel",
+ .size = 0xe0000,
+ .offset = 0x20000
+ },{
+ .name = "file system",
+ .size = 0x700000,
+ .offset = 0x00100000,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 1, /* use dma transfer with this chip*/
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+ .ctl_reg = 0x4, /* send zero */
+ .enable_dma = 0,
+ .bits_per_word = 8,
+ .cs_change_per_word = 1,
+};
+#endif
+
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+static struct bfin5xx_spi_chip ad5304_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 2, /* Framework chip select. On STAMP537 it is SPISSEL2*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) || defined(CONFIG_SPI_ADC_BF533_MODULE)
+ {
+ .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836-spi",
+ .max_speed_hz = 31250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_PBX)
+ {
+ .modalias = "fxs-spi",
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 3,
+ .controller_data= &spi_si3xxx_chip_info,
+ .mode = SPI_MODE_3,
+ },
+ {
+ .modalias = "fxo-spi",
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 2,
+ .controller_data= &spi_si3xxx_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+ {
+ .modalias = "ad5304_spi",
+ .max_speed_hz = 1000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 2,
+ .platform_data = NULL,
+ .controller_data = &ad5304_chip_info,
+ .mode = SPI_MODE_2,
+ },
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master spi_bfin_master_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+};
+
+static struct platform_device spi_bfin_master_device = {
+ .name = "bfin-spi-master",
+ .id = 1, /* Bus number */
+ .dev = {
+ .platform_data = &spi_bfin_master_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+static struct platform_device bfin_fb_device = {
+ .name = "bf537-fb",
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device bfin_uart_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart_resources),
+ .resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+};
+#endif
+
+static struct platform_device *stamp_devices[] __initdata = {
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+ &net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &spi_bfin_master_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+ &bfin_uart_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+ &bfin_sport0_uart_device,
+ &bfin_sport1_uart_device,
+#endif
+};
+
+static int __init stamp_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+ platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+ return 0;
+}
+
+arch_initcall(stamp_init);
diff --git a/arch/blackfin/mach-bf533/cpu.c b/arch/blackfin/mach-bf533/cpu.c
new file mode 100644
index 00000000000..99547c4c290
--- /dev/null
+++ b/arch/blackfin/mach-bf533/cpu.c
@@ -0,0 +1,161 @@
+/*
+ * File: arch/blackfin/mach-bf533/cpu.c
+ * Based on:
+ * Author: michael.kang@analog.com
+ *
+ * Created:
+ * Description: clock scaling for the bf533
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <asm/dpmc.h>
+#include <linux/fs.h>
+#include <asm/bfin-global.h>
+
+/* CONFIG_CLKIN_HZ=11059200 */
+#define VCO5 (CONFIG_CLKIN_HZ*45) /*497664000 */
+#define VCO4 (CONFIG_CLKIN_HZ*36) /*398131200 */
+#define VCO3 (CONFIG_CLKIN_HZ*27) /*298598400 */
+#define VCO2 (CONFIG_CLKIN_HZ*18) /*199065600 */
+#define VCO1 (CONFIG_CLKIN_HZ*9) /*99532800 */
+#define VCO(x) VCO##x
+
+#define FREQ(x) {VCO(x),VCO(x)/4},{VCO(x),VCO(x)/2},{VCO(x),VCO(x)}
+/* frequency */
+static struct cpufreq_frequency_table bf533_freq_table[] = {
+ FREQ(1),
+ FREQ(3),
+ {VCO4, VCO4 / 2}, {VCO4, VCO4},
+ FREQ(5),
+ {0, CPUFREQ_TABLE_END},
+};
+
+/*
+ * dpmc_fops->ioctl()
+ * static int dpmc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+ */
+static int bf533_getfreq(unsigned int cpu)
+{
+ unsigned long cclk_mhz, vco_mhz;
+
+ /* The driver only support single cpu */
+ if (cpu == 0)
+ dpmc_fops.ioctl(NULL, NULL, IOCTL_GET_CORECLOCK, &cclk_mhz);
+ else
+ cclk_mhz = -1;
+ return cclk_mhz;
+}
+
+static int bf533_target(struct cpufreq_policy *policy,
+ unsigned int target_freq, unsigned int relation)
+{
+ unsigned long cclk_mhz;
+ unsigned long vco_mhz;
+ unsigned long flags;
+ unsigned int index, vco_index;
+ int i;
+
+ struct cpufreq_freqs freqs;
+ if (cpufreq_frequency_table_target
+ (policy, bf533_freq_table, target_freq, relation, &index))
+ return -EINVAL;
+ cclk_mhz = bf533_freq_table[index].frequency;
+ vco_mhz = bf533_freq_table[index].index;
+
+ dpmc_fops.ioctl(NULL, NULL, IOCTL_CHANGE_FREQUENCY, &vco_mhz);
+ freqs.old = bf533_getfreq(0);
+ freqs.new = cclk_mhz;
+ freqs.cpu = 0;
+
+ pr_debug("cclk begin change to cclk %d,vco=%d,index=%d,target=%d,oldfreq=%d\n",
+ cclk_mhz, vco_mhz, index, target_freq, freqs.old);
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+ local_irq_save(flags);
+ dpmc_fops.ioctl(NULL, NULL, IOCTL_SET_CCLK, &cclk_mhz);
+ local_irq_restore(flags);
+ cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+ vco_mhz = get_vco();
+ cclk_mhz = get_cclk();
+ return 0;
+}
+
+/* make sure that only the "userspace" governor is run -- anything else wouldn't make sense on
+ * this platform, anyway.
+ */
+static int bf533_verify_speed(struct cpufreq_policy *policy)
+{
+ return cpufreq_frequency_table_verify(policy, &bf533_freq_table);
+}
+
+static int __init __bf533_cpu_init(struct cpufreq_policy *policy)
+{
+ int result;
+
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
+
+ policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+ /*Now ,only support one cpu */
+ policy->cur = bf533_getfreq(0);
+ cpufreq_frequency_table_get_attr(bf533_freq_table, policy->cpu);
+ return cpufreq_frequency_table_cpuinfo(policy, bf533_freq_table);
+}
+
+static struct freq_attr *bf533_freq_attr[] = {
+ &cpufreq_freq_attr_scaling_available_freqs,
+ NULL,
+};
+
+static struct cpufreq_driver bf533_driver = {
+ .verify = bf533_verify_speed,
+ .target = bf533_target,
+ .get = bf533_getfreq,
+ .init = __bf533_cpu_init,
+ .name = "bf533",
+ .owner = THIS_MODULE,
+ .attr = bf533_freq_attr,
+};
+
+static int __init bf533_cpu_init(void)
+{
+ return cpufreq_register_driver(&bf533_driver);
+}
+
+static void __exit bf533_cpu_exit(void)
+{
+ cpufreq_unregister_driver(&bf533_driver);
+}
+
+MODULE_AUTHOR("Mickael Kang");
+MODULE_DESCRIPTION("cpufreq driver for BF533 CPU");
+MODULE_LICENSE("GPL");
+
+module_init(bf533_cpu_init);
+module_exit(bf533_cpu_exit);
diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S
new file mode 100644
index 00000000000..4808edb0680
--- /dev/null
+++ b/arch/blackfin/mach-bf533/head.S
@@ -0,0 +1,774 @@
+/*
+ * File: arch/blackfin/mach-bf533/head.S
+ * Based on:
+ * Author: Jeff Dionne <jeff@uclinux.org> COPYRIGHT 1998 D. Jeff Dionne
+ *
+ * Created: 1998
+ * Description: bf533 startup file
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/linkage.h>
+#include <asm/blackfin.h>
+#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach/mem_init.h>
+#endif
+#if CONFIG_DEBUG_KERNEL_START
+#include <asm/mach-common/def_LPBlackfin.h>
+#endif
+
+.global __rambase
+.global __ramstart
+.global __ramend
+.extern ___bss_stop
+.extern ___bss_start
+.extern _bf53x_relocate_l1_mem
+
+#define INITIAL_STACK 0xFFB01000
+
+.text
+
+ENTRY(__start)
+ENTRY(__stext)
+ /* R0: argument of command line string, passed from uboot, save it */
+ R7 = R0;
+ /* Set the SYSCFG register */
+ R0 = 0x36;
+ /*Enable Cycle Counter and Nesting Of Interrupts(3rd Bit)*/
+ SYSCFG = R0;
+ R0 = 0;
+
+ /*Clear Out All the data and pointer Registers*/
+ R1 = R0;
+ R2 = R0;
+ R3 = R0;
+ R4 = R0;
+ R5 = R0;
+ R6 = R0;
+
+ P0 = R0;
+ P1 = R0;
+ P2 = R0;
+ P3 = R0;
+ P4 = R0;
+ P5 = R0;
+
+ LC0 = r0;
+ LC1 = r0;
+ L0 = r0;
+ L1 = r0;
+ L2 = r0;
+ L3 = r0;
+
+ /* Clear Out All the DAG Registers*/
+ B0 = r0;
+ B1 = r0;
+ B2 = r0;
+ B3 = r0;
+
+ I0 = r0;
+ I1 = r0;
+ I2 = r0;
+ I3 = r0;
+
+ M0 = r0;
+ M1 = r0;
+ M2 = r0;
+ M3 = r0;
+
+#if CONFIG_DEBUG_KERNEL_START
+
+/*
+ * Set up a temporary Event Vector Table, so if something bad happens before
+ * the kernel is fully started, it doesn't vector off into the bootloaders
+ * table
+ */
+ P0.l = lo(EVT2);
+ P0.h = hi(EVT2);
+ P1.l = lo(EVT15);
+ P1.h = hi(EVT15);
+ P2.l = debug_kernel_start_trap;
+ P2.h = debug_kernel_start_trap;
+
+ RTS = P2;
+ RTI = P2;
+ RTX = P2;
+ RTN = P2;
+ RTE = P2;
+
+.Lfill_temp_vector_table:
+ [P0++] = P2; /* Core Event Vector Table */
+ CC = P0 == P1;
+ if !CC JUMP .Lfill_temp_vector_table
+ P0 = r0;
+ P1 = r0;
+ P2 = r0;
+
+#endif
+
+ p0.h = hi(FIO_MASKA_C);
+ p0.l = lo(FIO_MASKA_C);
+ r0 = 0xFFFF(Z);
+ w[p0] = r0.L; /* Disable all interrupts */
+ ssync;
+
+ p0.h = hi(FIO_MASKB_C);
+ p0.l = lo(FIO_MASKB_C);
+ r0 = 0xFFFF(Z);
+ w[p0] = r0.L; /* Disable all interrupts */
+ ssync;
+
+ /* Turn off the icache */
+ p0.l = (IMEM_CONTROL & 0xFFFF);
+ p0.h = (IMEM_CONTROL >> 16);
+ R1 = [p0];
+ R0 = ~ENICPLB;
+ R0 = R0 & R1;
+
+ /* Anomaly 05000125 */
+#ifdef ANOMALY_05000125
+ CLI R2;
+ SSYNC;
+#endif
+ [p0] = R0;
+ SSYNC;
+#ifdef ANOMALY_05000125
+ STI R2;
+#endif
+
+ /* Turn off the dcache */
+ p0.l = (DMEM_CONTROL & 0xFFFF);
+ p0.h = (DMEM_CONTROL >> 16);
+ R1 = [p0];
+ R0 = ~ENDCPLB;
+ R0 = R0 & R1;
+
+ /* Anomaly 05000125 */
+#ifdef ANOMALY_05000125
+ CLI R2;
+ SSYNC;
+#endif
+ [p0] = R0;
+ SSYNC;
+#ifdef ANOMALY_05000125
+ STI R2;
+#endif
+
+ /* Initialise UART */
+ p0.h = hi(UART_LCR);
+ p0.l = lo(UART_LCR);
+ r0 = 0x0(Z);
+ w[p0] = r0.L; /* To enable DLL writes */
+ ssync;
+
+ p0.h = hi(UART_DLL);
+ p0.l = lo(UART_DLL);
+ r0 = 0x0(Z);
+ w[p0] = r0.L;
+ ssync;
+
+ p0.h = hi(UART_DLH);
+ p0.l = lo(UART_DLH);
+ r0 = 0x00(Z);
+ w[p0] = r0.L;
+ ssync;
+
+ p0.h = hi(UART_GCTL);
+ p0.l = lo(UART_GCTL);
+ r0 = 0x0(Z);
+ w[p0] = r0.L; /* To enable UART clock */
+ ssync;
+
+ /* Initialize stack pointer */
+ sp.l = lo(INITIAL_STACK);
+ sp.h = hi(INITIAL_STACK);
+ fp = sp;
+ usp = sp;
+
+ /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
+ call _bf53x_relocate_l1_mem;
+#if CONFIG_BFIN_KERNEL_CLOCK
+ call _start_dma_code;
+#endif
+
+ /* Code for initializing Async memory banks */
+
+ p2.h = hi(EBIU_AMBCTL1);
+ p2.l = lo(EBIU_AMBCTL1);
+ r0.h = hi(AMBCTL1VAL);
+ r0.l = lo(AMBCTL1VAL);
+ [p2] = r0;
+ ssync;
+
+ p2.h = hi(EBIU_AMBCTL0);
+ p2.l = lo(EBIU_AMBCTL0);
+ r0.h = hi(AMBCTL0VAL);
+ r0.l = lo(AMBCTL0VAL);
+ [p2] = r0;
+ ssync;
+
+ p2.h = hi(EBIU_AMGCTL);
+ p2.l = lo(EBIU_AMGCTL);
+ r0 = AMGCTLVAL;
+ w[p2] = r0;
+ ssync;
+
+ /* This section keeps the processor in supervisor mode
+ * during kernel boot. Switches to user mode at end of boot.
+ * See page 3-9 of Hardware Reference manual for documentation.
+ */
+
+ /* EVT15 = _real_start */
+
+ p0.l = lo(EVT15);
+ p0.h = hi(EVT15);
+ p1.l = _real_start;
+ p1.h = _real_start;
+ [p0] = p1;
+ csync;
+
+ p0.l = lo(IMASK);
+ p0.h = hi(IMASK);
+ p1.l = IMASK_IVG15;
+ p1.h = 0x0;
+ [p0] = p1;
+ csync;
+
+ raise 15;
+ p0.l = .LWAIT_HERE;
+ p0.h = .LWAIT_HERE;
+ reti = p0;
+#if defined(ANOMALY_05000281)
+ nop; nop; nop;
+#endif
+ rti;
+
+.LWAIT_HERE:
+ jump .LWAIT_HERE;
+
+ENTRY(_real_start)
+ [ -- sp ] = reti;
+ p0.l = lo(WDOG_CTL);
+ p0.h = hi(WDOG_CTL);
+ r0 = 0xAD6(z);
+ w[p0] = r0; /* watchdog off for now */
+ ssync;
+
+ /* Code update for BSS size == 0
+ * Zero out the bss region.
+ */
+
+ p1.l = ___bss_start;
+ p1.h = ___bss_start;
+ p2.l = ___bss_stop;
+ p2.h = ___bss_stop;
+ r0 = 0;
+ p2 -= p1;
+ lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2;
+.L_clear_bss:
+ B[p1++] = r0;
+
+ /* In case there is a NULL pointer reference
+ * Zero out region before stext
+ */
+
+ p1.l = 0x0;
+ p1.h = 0x0;
+ r0.l = __stext;
+ r0.h = __stext;
+ r0 = r0 >> 1;
+ p2 = r0;
+ r0 = 0;
+ lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2;
+.L_clear_zero:
+ W[p1++] = r0;
+
+/* pass the uboot arguments to the global value command line */
+ R0 = R7;
+ call _cmdline_init;
+
+ p1.l = __rambase;
+ p1.h = __rambase;
+ r0.l = __sdata;
+ r0.h = __sdata;
+ [p1] = r0;
+
+ p1.l = __ramstart;
+ p1.h = __ramstart;
+ p3.l = ___bss_stop;
+ p3.h = ___bss_stop;
+
+ r1 = p3;
+ [p1] = r1;
+
+ /*
+ * load the current thread pointer and stack
+ */
+ r1.l = _init_thread_union;
+ r1.h = _init_thread_union;
+
+ r2.l = 0x2000;
+ r2.h = 0x0000;
+ r1 = r1 + r2;
+ sp = r1;
+ usp = sp;
+ fp = sp;
+ call _start_kernel;
+.L_exit:
+ jump.s .L_exit;
+
+.section .l1.text
+#if CONFIG_BFIN_KERNEL_CLOCK
+ENTRY(_start_dma_code)
+ p0.h = hi(SIC_IWR);
+ p0.l = lo(SIC_IWR);
+ r0.l = 0x1;
+ r0.h = 0x0;
+ [p0] = r0;
+ SSYNC;
+
+ /*
+ * Set PLL_CTL
+ * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+ * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
+ * - [7] = output delay (add 200ps of delay to mem signals)
+ * - [6] = input delay (add 200ps of input delay to mem signals)
+ * - [5] = PDWN : 1=All Clocks off
+ * - [3] = STOPCK : 1=Core Clock off
+ * - [1] = PLL_OFF : 1=Disable Power to PLL
+ * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+ * all other bits set to zero
+ */
+
+ p0.h = hi(PLL_LOCKCNT);
+ p0.l = lo(PLL_LOCKCNT);
+ r0 = 0x300(Z);
+ w[p0] = r0.l;
+ ssync;
+
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITSET (R0, 24);
+ [P2] = R0;
+ SSYNC;
+
+ r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
+ r0 = r0 << 9; /* Shift it over, */
+ r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
+ r0 = r1 | r0;
+ r1 = PLL_BYPASS; /* Bypass the PLL? */
+ r1 = r1 << 8; /* Shift it over */
+ r0 = r1 | r0; /* add them all together */
+
+ p0.h = hi(PLL_CTL);
+ p0.l = lo(PLL_CTL); /* Load the address */
+ cli r2; /* Disable interrupts */
+ ssync;
+ w[p0] = r0.l; /* Set the value */
+ idle; /* Wait for the PLL to stablize */
+ sti r2; /* Enable interrupts */
+
+.Lcheck_again:
+ p0.h = hi(PLL_STAT);
+ p0.l = lo(PLL_STAT);
+ R0 = W[P0](Z);
+ CC = BITTST(R0,5);
+ if ! CC jump .Lcheck_again;
+
+ /* Configure SCLK & CCLK Dividers */
+ r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+ p0.h = hi(PLL_DIV);
+ p0.l = lo(PLL_DIV);
+ w[p0] = r0.l;
+ ssync;
+
+ p0.l = lo(EBIU_SDRRC);
+ p0.h = hi(EBIU_SDRRC);
+ r0 = mem_SDRRC;
+ w[p0] = r0.l;
+ ssync;
+
+ p0.l = (EBIU_SDBCTL & 0xFFFF);
+ p0.h = (EBIU_SDBCTL >> 16); /* SDRAM Memory Bank Control Register */
+ r0 = mem_SDBCTL;
+ w[p0] = r0.l;
+ ssync;
+
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITCLR (R0, 24);
+ p0.h = hi(EBIU_SDSTAT);
+ p0.l = lo(EBIU_SDSTAT);
+ r2.l = w[p0];
+ cc = bittst(r2,3);
+ if !cc jump .Lskip;
+ NOP;
+ BITSET (R0, 23);
+.Lskip:
+ [P2] = R0;
+ SSYNC;
+
+ R0.L = lo(mem_SDGCTL);
+ R0.H = hi(mem_SDGCTL);
+ R1 = [p2];
+ R1 = R1 | R0;
+ [P2] = R1;
+ SSYNC;
+
+ p0.h = hi(SIC_IWR);
+ p0.l = lo(SIC_IWR);
+ r0.l = lo(IWR_ENABLE_ALL)
+ r0.h = hi(IWR_ENABLE_ALL)
+ [p0] = r0;
+ SSYNC;
+
+ RTS;
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */
+
+ENTRY(_bfin_reset)
+ /* No more interrupts to be handled*/
+ CLI R6;
+ SSYNC;
+
+#if defined(CONFIG_BFIN_SHARED_FLASH_ENET)
+ p0.h = hi(FIO_INEN);
+ p0.l = lo(FIO_INEN);
+ r0.l = ~(1 << CONFIG_ENET_FLASH_PIN);
+ w[p0] = r0.l;
+
+ p0.h = hi(FIO_DIR);
+ p0.l = lo(FIO_DIR);
+ r0.l = (1 << CONFIG_ENET_FLASH_PIN);
+ w[p0] = r0.l;
+
+ p0.h = hi(FIO_FLAG_C);
+ p0.l = lo(FIO_FLAG_C);
+ r0.l = (1 << CONFIG_ENET_FLASH_PIN);
+ w[p0] = r0.l;
+#endif
+
+ /* Clear the bits 13-15 in SWRST if they werent cleared */
+ p0.h = hi(SWRST);
+ p0.l = lo(SWRST);
+ csync;
+ r0.l = w[p0];
+
+ /* Clear the IMASK register */
+ p0.h = hi(IMASK);
+ p0.l = lo(IMASK);
+ r0 = 0x0;
+ [p0] = r0;
+
+ /* Clear the ILAT register */
+ p0.h = hi(ILAT);
+ p0.l = lo(ILAT);
+ r0 = [p0];
+ [p0] = r0;
+ SSYNC;
+
+ /* Disable the WDOG TIMER */
+ p0.h = hi(WDOG_CTL);
+ p0.l = lo(WDOG_CTL);
+ r0.l = 0xAD6;
+ w[p0] = r0.l;
+ SSYNC;
+
+ /* Clear the sticky bit incase it is already set */
+ p0.h = hi(WDOG_CTL);
+ p0.l = lo(WDOG_CTL);
+ r0.l = 0x8AD6;
+ w[p0] = r0.l;
+ SSYNC;
+
+ /* Program the count value */
+ R0.l = 0x100;
+ R0.h = 0x0;
+ P0.h = hi(WDOG_CNT);
+ P0.l = lo(WDOG_CNT);
+ [P0] = R0;
+ SSYNC;
+
+ /* Program WDOG_STAT if necessary */
+ P0.h = hi(WDOG_CTL);
+ P0.l = lo(WDOG_CTL);
+ R0 = W[P0](Z);
+ CC = BITTST(R0,1);
+ if !CC JUMP .LWRITESTAT;
+ CC = BITTST(R0,2);
+ if !CC JUMP .LWRITESTAT;
+ JUMP .LSKIP_WRITE;
+
+.LWRITESTAT:
+ /* When watch dog timer is enabled, a write to STAT will load the contents of CNT to STAT */
+ R0 = 0x0000(z);
+ P0.h = hi(WDOG_STAT);
+ P0.l = lo(WDOG_STAT)
+ [P0] = R0;
+ SSYNC;
+
+.LSKIP_WRITE:
+ /* Enable the reset event */
+ P0.h = hi(WDOG_CTL);
+ P0.l = lo(WDOG_CTL);
+ R0 = W[P0](Z);
+ BITCLR(R0,1);
+ BITCLR(R0,2);
+ W[P0] = R0.L;
+ SSYNC;
+ NOP;
+
+ /* Enable the wdog counter */
+ R0 = W[P0](Z);
+ BITCLR(R0,4);
+ W[P0] = R0.L;
+ SSYNC;
+
+ IDLE;
+
+ RTS;
+
+#if CONFIG_DEBUG_KERNEL_START
+debug_kernel_start_trap:
+ /* Set up a temp stack in L1 - SDRAM might not be working */
+ P0.L = lo(L1_DATA_A_START + 0x100);
+ P0.H = hi(L1_DATA_A_START + 0x100);
+ SP = P0;
+
+ /* Make sure the Clocks are the way I think they should be */
+ r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
+ r0 = r0 << 9; /* Shift it over, */
+ r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/
+ r0 = r1 | r0;
+ r1 = PLL_BYPASS; /* Bypass the PLL? */
+ r1 = r1 << 8; /* Shift it over */
+ r0 = r1 | r0; /* add them all together */
+
+ p0.h = hi(PLL_CTL);
+ p0.l = lo(PLL_CTL); /* Load the address */
+ cli r2; /* Disable interrupts */
+ ssync;
+ w[p0] = r0.l; /* Set the value */
+ idle; /* Wait for the PLL to stablize */
+ sti r2; /* Enable interrupts */
+
+.Lcheck_again1:
+ p0.h = hi(PLL_STAT);
+ p0.l = lo(PLL_STAT);
+ R0 = W[P0](Z);
+ CC = BITTST(R0,5);
+ if ! CC jump .Lcheck_again1;
+
+ /* Configure SCLK & CCLK Dividers */
+ r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+ p0.h = hi(PLL_DIV);
+ p0.l = lo(PLL_DIV);
+ w[p0] = r0.l;
+ ssync;
+
+ /* Make sure UART is enabled - you can never be sure */
+
+/*
+ * Setup for console. Argument comes from the menuconfig
+ */
+
+#ifdef CONFIG_BAUD_9600
+#define CONSOLE_BAUD_RATE 9600
+#elif CONFIG_BAUD_19200
+#define CONSOLE_BAUD_RATE 19200
+#elif CONFIG_BAUD_38400
+#define CONSOLE_BAUD_RATE 38400
+#elif CONFIG_BAUD_57600
+#define CONSOLE_BAUD_RATE 57600
+#elif CONFIG_BAUD_115200
+#define CONSOLE_BAUD_RATE 115200
+#endif
+
+ p0.h = hi(UART_GCTL);
+ p0.l = lo(UART_GCTL);
+ r0 = 0x00(Z);
+ w[p0] = r0.L; /* To Turn off UART clocks */
+ ssync;
+
+ p0.h = hi(UART_LCR);
+ p0.l = lo(UART_LCR);
+ r0 = 0x83(Z);
+ w[p0] = r0.L; /* To enable DLL writes */
+ ssync;
+
+ R1 = (((CONFIG_CLKIN_HZ * CONFIG_VCO_MULT) / CONFIG_SCLK_DIV) / (CONSOLE_BAUD_RATE * 16));
+
+ p0.h = hi(UART_DLL);
+ p0.l = lo(UART_DLL);
+ r0 = 0xFF(Z);
+ r0 = R1 & R0;
+ w[p0] = r0.L;
+ ssync;
+
+ p0.h = hi(UART_DLH);
+ p0.l = lo(UART_DLH);
+ r1 >>= 8 ;
+ w[p0] = r1.L;
+ ssync;
+
+ p0.h = hi(UART_GCTL);
+ p0.l = lo(UART_GCTL);
+ r0 = 0x0(Z);
+ w[p0] = r0.L; /* To enable UART clock */
+ ssync;
+
+ p0.h = hi(UART_LCR);
+ p0.l = lo(UART_LCR);
+ r0 = 0x03(Z);
+ w[p0] = r0.L; /* To Turn on UART */
+ ssync;
+
+ p0.h = hi(UART_GCTL);
+ p0.l = lo(UART_GCTL);
+ r0 = 0x01(Z);
+ w[p0] = r0.L; /* To Turn on UART Clocks */
+ ssync;
+
+ P0.h = hi(UART_THR);
+ P0.l = lo(UART_THR);
+ P1.h = hi(UART_LSR);
+ P1.l = lo(UART_LSR);
+
+ R0.L = 'K';
+ call .Lwait_char;
+ R0.L='e';
+ call .Lwait_char;
+ R0.L='r';
+ call .Lwait_char;
+ R0.L='n'
+ call .Lwait_char;
+ R0.L='e'
+ call .Lwait_char;
+ R0.L='l';
+ call .Lwait_char;
+ R0.L=' ';
+ call .Lwait_char;
+ R0.L='c';
+ call .Lwait_char;
+ R0.L='r';
+ call .Lwait_char;
+ R0.L='a';
+ call .Lwait_char;
+ R0.L='s';
+ call .Lwait_char;
+ R0.L='h';
+ call .Lwait_char;
+ R0.L='\r';
+ call .Lwait_char;
+ R0.L='\n';
+ call .Lwait_char;
+
+ R0.L='S';
+ call .Lwait_char;
+ R0.L='E';
+ call .Lwait_char;
+ R0.L='Q'
+ call .Lwait_char;
+ R0.L='S'
+ call .Lwait_char;
+ R0.L='T';
+ call .Lwait_char;
+ R0.L='A';
+ call .Lwait_char;
+ R0.L='T';
+ call .Lwait_char;
+ R0.L='=';
+ call .Lwait_char;
+ R2 = SEQSTAT;
+ call .Ldump_reg;
+
+ R0.L=' ';
+ call .Lwait_char;
+ R0.L='R';
+ call .Lwait_char;
+ R0.L='E'
+ call .Lwait_char;
+ R0.L='T'
+ call .Lwait_char;
+ R0.L='X';
+ call .Lwait_char;
+ R0.L='=';
+ call .Lwait_char;
+ R2 = RETX;
+ call .Ldump_reg;
+
+ R0.L='\r';
+ call .Lwait_char;
+ R0.L='\n';
+ call .Lwait_char;
+
+.Ldebug_kernel_start_trap_done:
+ JUMP .Ldebug_kernel_start_trap_done;
+.Ldump_reg:
+ R3 = 32;
+ R4 = 0x0F;
+ R5 = ':'; /* one past 9 */
+
+.Ldump_reg2:
+ R0 = R2;
+ R3 += -4;
+ R0 >>>= R3;
+ R0 = R0 & R4;
+ R0 += 0x30;
+ CC = R0 <= R5;
+ if CC JUMP .Ldump_reg1;
+ R0 += 7;
+
+.Ldump_reg1:
+ R1.l = W[P1];
+ CC = BITTST(R1, 5);
+ if !CC JUMP .Ldump_reg1;
+ W[P0] = r0;
+
+ CC = R3 == 0;
+ if !CC JUMP .Ldump_reg2
+ RTS;
+
+.Lwait_char:
+ R1.l = W[P1];
+ CC = BITTST(R1, 5);
+ if !CC JUMP .Lwait_char;
+ W[P0] = r0;
+ RTS;
+
+#endif /* CONFIG_DEBUG_KERNEL_START */
+
+.data
+
+/*
+ * Set up the usable of RAM stuff. Size of RAM is determined then
+ * an initial stack set up at the end.
+ */
+
+.align 4
+__rambase:
+.long 0
+__ramstart:
+.long 0
+__ramend:
+.long 0
diff --git a/arch/blackfin/mach-bf533/ints-priority.c b/arch/blackfin/mach-bf533/ints-priority.c
new file mode 100644
index 00000000000..36a69334520
--- /dev/null
+++ b/arch/blackfin/mach-bf533/ints-priority.c
@@ -0,0 +1,65 @@
+/*
+ * File: arch/blackfin/mach-bf533/ints-priority.c
+ * Based on:
+ * Author: Michael Hennerich
+ *
+ * Created: ?
+ * Description: Set up the interupt priorities
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/module.h>
+#include <asm/blackfin.h>
+#include <asm/irq.h>
+
+void program_IAR(void)
+{
+ /* Program the IAR0 Register with the configured priority */
+ bfin_write_SIC_IAR0(((CONFIG_PLLWAKE_ERROR - 7) << PLLWAKE_ERROR_POS) |
+ ((CONFIG_DMA_ERROR - 7) << DMA_ERROR_POS) |
+ ((CONFIG_PPI_ERROR - 7) << PPI_ERROR_POS) |
+ ((CONFIG_SPORT0_ERROR - 7) << SPORT0_ERROR_POS) |
+ ((CONFIG_SPI_ERROR - 7) << SPI_ERROR_POS) |
+ ((CONFIG_SPORT1_ERROR - 7) << SPORT1_ERROR_POS) |
+ ((CONFIG_UART_ERROR - 7) << UART_ERROR_POS) |
+ ((CONFIG_RTC_ERROR - 7) << RTC_ERROR_POS));
+
+ bfin_write_SIC_IAR1(((CONFIG_DMA0_PPI - 7) << DMA0_PPI_POS) |
+ ((CONFIG_DMA1_SPORT0RX - 7) << DMA1_SPORT0RX_POS) |
+ ((CONFIG_DMA2_SPORT0TX - 7) << DMA2_SPORT0TX_POS) |
+ ((CONFIG_DMA3_SPORT1RX - 7) << DMA3_SPORT1RX_POS) |
+ ((CONFIG_DMA4_SPORT1TX - 7) << DMA4_SPORT1TX_POS) |
+ ((CONFIG_DMA5_SPI - 7) << DMA5_SPI_POS) |
+ ((CONFIG_DMA6_UARTRX - 7) << DMA6_UARTRX_POS) |
+ ((CONFIG_DMA7_UARTTX - 7) << DMA7_UARTTX_POS));
+
+ bfin_write_SIC_IAR2(((CONFIG_TIMER0 - 7) << TIMER0_POS) |
+ ((CONFIG_TIMER1 - 7) << TIMER1_POS) |
+ ((CONFIG_TIMER2 - 7) << TIMER2_POS) |
+ ((CONFIG_PFA - 7) << PFA_POS) |
+ ((CONFIG_PFB - 7) << PFB_POS) |
+ ((CONFIG_MEMDMA0 - 7) << MEMDMA0_POS) |
+ ((CONFIG_MEMDMA1 - 7) << MEMDMA1_POS) |
+ ((CONFIG_WDTIMER - 7) << WDTIMER_POS));
+
+ SSYNC();
+}