diff options
Diffstat (limited to 'arch/blackfin/mach-bf537/include/mach/defBF534.h')
| -rw-r--r-- | arch/blackfin/mach-bf537/include/mach/defBF534.h | 95 |
1 files changed, 0 insertions, 95 deletions
diff --git a/arch/blackfin/mach-bf537/include/mach/defBF534.h b/arch/blackfin/mach-bf537/include/mach/defBF534.h index a6d20ca5768..066d5c261f4 100644 --- a/arch/blackfin/mach-bf537/include/mach/defBF534.h +++ b/arch/blackfin/mach-bf537/include/mach/defBF534.h @@ -958,67 +958,6 @@ ** modifier UNLESS the lower order bits are saved and ORed back in when ** the macro is used. *************************************************************************************/ -/* -** ********************* PLL AND RESET MASKS ****************************************/ -/* PLL_CTL Masks */ -#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */ -#define PLL_OFF 0x0002 /* PLL Not Powered */ -#define STOPCK 0x0008 /* Core Clock Off */ -#define PDWN 0x0020 /* Enter Deep Sleep Mode */ -#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */ -#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */ -#define BYPASS 0x0100 /* Bypass the PLL */ -#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */ -/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */ -#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */ - -/* PLL_DIV Masks */ -#define SSEL 0x000F /* System Select */ -#define CSEL 0x0030 /* Core Select */ -#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */ -#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */ -#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */ -#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */ -/* PLL_DIV Macros */ -#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */ - -/* VR_CTL Masks */ -#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */ -#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */ -#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */ -#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */ -#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */ - -#define GAIN 0x000C /* Voltage Level Gain */ -#define GAIN_5 0x0000 /* GAIN = 5 */ -#define GAIN_10 0x0004 /* GAIN = 10 */ -#define GAIN_20 0x0008 /* GAIN = 20 */ -#define GAIN_50 0x000C /* GAIN = 50 */ - -#define VLEV 0x00F0 /* Internal Voltage Level */ -#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */ -#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */ -#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */ -#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */ -#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */ -#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */ -#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */ -#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */ -#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */ -#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */ - -#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */ -#define CANWE 0x0200 /* Enable CAN Wakeup From Hibernate */ -#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */ -#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */ -#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */ -#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */ - -/* PLL_STAT Masks */ -#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */ -#define FULL_ON 0x0002 /* Processor In Full On Mode */ -#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */ -#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */ /* CHIPID Masks */ #define CHIPID_VERSION 0xF0000000 @@ -1645,34 +1584,6 @@ #define BGSTAT 0x0020 /* Bus Grant Status */ /* ************************** DMA CONTROLLER MASKS ********************************/ -/* DMAx_CONFIG, MDMA_yy_CONFIG Masks */ -#define DMAEN 0x0001 /* DMA Channel Enable */ -#define WNR 0x0002 /* Channel Direction (W/R*) */ -#define WDSIZE_8 0x0000 /* Transfer Word Size = 8 */ -#define WDSIZE_16 0x0004 /* Transfer Word Size = 16 */ -#define WDSIZE_32 0x0008 /* Transfer Word Size = 32 */ -#define DMA2D 0x0010 /* DMA Mode (2D/1D*) */ -#define RESTART 0x0020 /* DMA Buffer Clear */ -#define DI_SEL 0x0040 /* Data Interrupt Timing Select */ -#define DI_EN 0x0080 /* Data Interrupt Enable */ -#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */ -#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */ -#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */ -#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */ -#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */ -#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */ -#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */ -#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */ -#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */ -#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */ -#define NDSIZE 0x0900 /* Next Descriptor Size */ - -#define DMAFLOW 0x7000 /* Flow Control */ -#define DMAFLOW_STOP 0x0000 /* Stop Mode */ -#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */ -#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */ -#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */ -#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */ /* DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks */ #define CTYPE 0x0040 /* DMA Channel Type Indicator (Memory/Peripheral*) */ @@ -1690,12 +1601,6 @@ #define PMAP_UART1RX 0xA000 /* UART1 Port Receive DMA */ #define PMAP_UART1TX 0xB000 /* UART1 Port Transmit DMA */ -/* DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks */ -#define DMA_DONE 0x0001 /* DMA Completion Interrupt Status */ -#define DMA_ERR 0x0002 /* DMA Error Interrupt Status */ -#define DFETCH 0x0004 /* DMA Descriptor Fetch Indicator */ -#define DMA_RUN 0x0008 /* DMA Channel Running Indicator */ - /* ************ PARALLEL PERIPHERAL INTERFACE (PPI) MASKS *************/ /* PPI_CONTROL Masks */ #define PORT_EN 0x0001 /* PPI Port Enable */ |