diff options
Diffstat (limited to 'arch/blackfin/mach-bf537')
21 files changed, 659 insertions, 845 deletions
diff --git a/arch/blackfin/mach-bf537/Kconfig b/arch/blackfin/mach-bf537/Kconfig index 8255374c04a..bbc08fd4f12 100644 --- a/arch/blackfin/mach-bf537/Kconfig +++ b/arch/blackfin/mach-bf537/Kconfig @@ -64,29 +64,29 @@ config IRQ_MAC_RX config IRQ_MAC_TX int "IRQ_MAC_TX" default 11 -config IRQ_TMR0 - int "IRQ_TMR0" - default 12 -config IRQ_TMR1 - int "IRQ_TMR1" +config IRQ_TIMER0 + int "IRQ_TIMER0" + default 8 +config IRQ_TIMER1 + int "IRQ_TIMER1" default 12 -config IRQ_TMR2 - int "IRQ_TMR2" +config IRQ_TIMER2 + int "IRQ_TIMER2" default 12 -config IRQ_TMR3 - int "IRQ_TMR3" +config IRQ_TIMER3 + int "IRQ_TIMER3" default 12 -config IRQ_TMR4 - int "IRQ_TMR4" +config IRQ_TIMER4 + int "IRQ_TIMER4" default 12 -config IRQ_TMR5 - int "IRQ_TMR5" +config IRQ_TIMER5 + int "IRQ_TIMER5" default 12 -config IRQ_TMR6 - int "IRQ_TMR6" +config IRQ_TIMER6 + int "IRQ_TIMER6" default 12 -config IRQ_TMR7 - int "IRQ_TMR7" +config IRQ_TIMER7 + int "IRQ_TIMER7" default 12 config IRQ_PROG_INTA int "IRQ_PROG_INTA" diff --git a/arch/blackfin/mach-bf537/Makefile b/arch/blackfin/mach-bf537/Makefile index 68e5478e95a..56994b675f9 100644 --- a/arch/blackfin/mach-bf537/Makefile +++ b/arch/blackfin/mach-bf537/Makefile @@ -2,6 +2,4 @@ # arch/blackfin/mach-bf537/Makefile # -extra-y := head.o - obj-y := ints-priority.o dma.o diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c index dde14720b0e..6ac8e4d5bd3 100644 --- a/arch/blackfin/mach-bf537/boards/cm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c @@ -308,6 +308,19 @@ static struct platform_device net2272_bfin_device = { }; #endif +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) static struct mtd_partition cm_partitions[] = { { @@ -379,30 +392,57 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; - -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) static struct resource bfin_twi0_resource[] = { @@ -525,7 +565,12 @@ static struct platform_device *cm_bf537_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) @@ -564,6 +609,8 @@ static struct platform_device *cm_bf537_devices[] __initdata = { #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) &cm_flash_device, #endif + + &bfin_gpios_device, }; static int __init cm_bf537_init(void) diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c index 78a13d5bfd5..dd6e6bfb98e 100644 --- a/arch/blackfin/mach-bf537/boards/generic_board.c +++ b/arch/blackfin/mach-bf537/boards/generic_board.c @@ -50,57 +50,46 @@ /* * Name the Board for the /proc/cpuinfo */ -const char bfin_board_name[] = "GENERIC Board"; +const char bfin_board_name[] = "UNKNOWN BOARD"; /* * Driver needs to know address, irq and flag pin. */ -#define ISP1761_BASE 0x203C0000 -#define ISP1761_IRQ IRQ_PF7 - #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) -static struct resource bfin_isp1761_resources[] = { +#include <linux/usb/isp1760.h> +static struct resource bfin_isp1760_resources[] = { [0] = { - .name = "isp1761-regs", - .start = ISP1761_BASE + 0x00000000, - .end = ISP1761_BASE + 0x000fffff, + .start = 0x203C0000, + .end = 0x203C0000 + 0x000fffff, .flags = IORESOURCE_MEM, }, [1] = { - .start = ISP1761_IRQ, - .end = ISP1761_IRQ, + .start = IRQ_PF7, + .end = IRQ_PF7, .flags = IORESOURCE_IRQ, }, }; -static struct platform_device bfin_isp1761_device = { - .name = "isp1761", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_isp1761_resources), - .resource = bfin_isp1761_resources, +static struct isp1760_platform_data isp1760_priv = { + .is_isp1761 = 0, + .port1_disable = 0, + .bus_width_16 = 1, + .port1_otg = 0, + .analog_oc = 0, + .dack_polarity_high = 0, + .dreq_polarity_high = 0, }; -static struct platform_device *bfin_isp1761_devices[] = { - &bfin_isp1761_device, +static struct platform_device bfin_isp1760_device = { + .name = "isp1760-hcd", + .id = 0, + .dev = { + .platform_data = &isp1760_priv, + }, + .num_resources = ARRAY_SIZE(bfin_isp1760_resources), + .resource = bfin_isp1760_resources, }; - -int __init bfin_isp1761_init(void) -{ - unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices); - - printk(KERN_INFO "%s(): registering device resources\n", __func__); - set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING); - - return platform_add_devices(bfin_isp1761_devices, num_devices); -} - -void __exit bfin_isp1761_exit(void) -{ - platform_device_unregister(&bfin_isp1761_device); -} - -arch_initcall(bfin_isp1761_init); #endif #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) @@ -559,30 +548,59 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) static struct resource bfin_twi0_resource[] = { @@ -651,6 +669,10 @@ static struct platform_device *stamp_devices[] __initdata = { &net2272_bfin_device, #endif +#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) + &bfin_isp1760_device, +#endif + #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) &bfin_spi0_device, #endif @@ -668,7 +690,12 @@ static struct platform_device *stamp_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c index 48c4cd2d1be..bb795341cb1 100644 --- a/arch/blackfin/mach-bf537/boards/minotaur.c +++ b/arch/blackfin/mach-bf537/boards/minotaur.c @@ -226,30 +226,59 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) static struct resource bfin_twi0_resource[] = { @@ -311,7 +340,12 @@ static struct platform_device *minotaur_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c index f9174c11cbd..89de94f4545 100644 --- a/arch/blackfin/mach-bf537/boards/pnav10.c +++ b/arch/blackfin/mach-bf537/boards/pnav10.c @@ -49,7 +49,7 @@ /* * Name the Board for the /proc/cpuinfo */ -const char bfin_board_name[] = "PNAV-1.0"; +const char bfin_board_name[] = "ADI PNAV-1.0"; /* * Driver needs to know address, irq and flag pin. @@ -453,30 +453,59 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif static struct platform_device *stamp_devices[] __initdata = { #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) @@ -520,7 +549,12 @@ static struct platform_device *stamp_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif }; diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c index 8d394393201..d812e2514a2 100644 --- a/arch/blackfin/mach-bf537/boards/stamp.c +++ b/arch/blackfin/mach-bf537/boards/stamp.c @@ -46,6 +46,7 @@ #include <linux/interrupt.h> #include <linux/i2c.h> #include <linux/usb/sl811.h> +#include <linux/spi/mmc_spi.h> #include <asm/dma.h> #include <asm/bfin5xx_spi.h> #include <asm/reboot.h> @@ -55,57 +56,46 @@ /* * Name the Board for the /proc/cpuinfo */ -const char bfin_board_name[] = "ADDS-BF537-STAMP"; +const char bfin_board_name[] = "ADI BF537-STAMP"; /* * Driver needs to know address, irq and flag pin. */ -#define ISP1761_BASE 0x203C0000 -#define ISP1761_IRQ IRQ_PF7 - #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) -static struct resource bfin_isp1761_resources[] = { +#include <linux/usb/isp1760.h> +static struct resource bfin_isp1760_resources[] = { [0] = { - .name = "isp1761-regs", - .start = ISP1761_BASE + 0x00000000, - .end = ISP1761_BASE + 0x000fffff, + .start = 0x203C0000, + .end = 0x203C0000 + 0x000fffff, .flags = IORESOURCE_MEM, }, [1] = { - .start = ISP1761_IRQ, - .end = ISP1761_IRQ, - .flags = IORESOURCE_IRQ, + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, }, }; -static struct platform_device bfin_isp1761_device = { - .name = "isp1761", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_isp1761_resources), - .resource = bfin_isp1761_resources, +static struct isp1760_platform_data isp1760_priv = { + .is_isp1761 = 0, + .port1_disable = 0, + .bus_width_16 = 1, + .port1_otg = 0, + .analog_oc = 0, + .dack_polarity_high = 0, + .dreq_polarity_high = 0, }; -static struct platform_device *bfin_isp1761_devices[] = { - &bfin_isp1761_device, +static struct platform_device bfin_isp1760_device = { + .name = "isp1760-hcd", + .id = 0, + .dev = { + .platform_data = &isp1760_priv, + }, + .num_resources = ARRAY_SIZE(bfin_isp1760_resources), + .resource = bfin_isp1760_resources, }; - -int __init bfin_isp1761_init(void) -{ - unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices); - - printk(KERN_INFO "%s(): registering device resources\n", __func__); - set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING); - - return platform_add_devices(bfin_isp1761_devices, num_devices); -} - -void __exit bfin_isp1761_exit(void) -{ - platform_device_unregister(&bfin_isp1761_device); -} - -arch_initcall(bfin_isp1761_init); #endif #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) @@ -443,11 +433,11 @@ static struct mtd_partition stamp_partitions[] = { .offset = 0, }, { .name = "linux kernel(nor)", - .size = 0xE0000, + .size = 0x180000, .offset = MTDPART_OFS_APPEND, }, { .name = "file system(nor)", - .size = 0x400000 - 0x40000 - 0xE0000 - 0x10000, + .size = 0x400000 - 0x40000 - 0x180000 - 0x10000, .offset = MTDPART_OFS_APPEND, }, { .name = "MAC Address(nor)", @@ -490,7 +480,7 @@ static struct mtd_partition bfin_spi_flash_partitions[] = { .mask_flags = MTD_CAP_ROM }, { .name = "linux kernel(spi)", - .size = 0xe0000, + .size = 0x180000, .offset = MTDPART_OFS_APPEND, }, { .name = "file system(spi)", @@ -503,7 +493,7 @@ static struct flash_platform_data bfin_spi_flash_data = { .name = "m25p80", .parts = bfin_spi_flash_partitions, .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), - .type = "m25p64", + /* .type = "m25p64", */ }; /* SPI flash chip (m25p64) */ @@ -537,9 +527,29 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = { }; #endif -#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) -static struct bfin5xx_spi_chip spi_mmc_chip_info = { - .enable_dma = 1, +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) +#define MMC_SPI_CARD_DETECT_INT IRQ_PF5 + +static int bfin_mmc_spi_init(struct device *dev, + irqreturn_t (*detect_int)(int, void *), void *data) +{ + return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int, + IRQF_TRIGGER_FALLING, "mmc-spi-detect", data); +} + +static void bfin_mmc_spi_exit(struct device *dev, void *data) +{ + free_irq(MMC_SPI_CARD_DETECT_INT, data); +} + +static struct mmc_spi_platform_data bfin_mmc_spi_pdata = { + .init = bfin_mmc_spi_init, + .exit = bfin_mmc_spi_exit, + .detect_delay = 100, /* msecs */ +}; + +static struct bfin5xx_spi_chip mmc_spi_chip_info = { + .enable_dma = 0, .bits_per_word = 8, }; #endif @@ -613,6 +623,14 @@ static struct bfin5xx_spi_chip lq035q1_spi_chip_info = { }; #endif +#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE) +static struct bfin5xx_spi_chip enc28j60_spi_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, + .cs_gpio = GPIO_PF10, +}; +#endif + #if defined(CONFIG_MTD_DATAFLASH) \ || defined(CONFIG_MTD_DATAFLASH_MODULE) @@ -624,7 +642,7 @@ static struct mtd_partition bfin_spi_dataflash_partitions[] = { .mask_flags = MTD_CAP_ROM }, { .name = "linux kernel(spi)", - .size = 0xe0000, + .size = 0x180000, .offset = MTDPART_OFS_APPEND, }, { .name = "file system(spi)", @@ -703,23 +721,14 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { .controller_data = &ad9960_spi_chip_info, }, #endif -#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) { - .modalias = "spi_mmc_dummy", + .modalias = "mmc_spi", .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ .bus_num = 0, - .chip_select = 0, - .platform_data = NULL, - .controller_data = &spi_mmc_chip_info, - .mode = SPI_MODE_3, - }, - { - .modalias = "spi_mmc", - .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ - .bus_num = 0, - .chip_select = CONFIG_SPI_MMC_CS_CHAN, - .platform_data = NULL, - .controller_data = &spi_mmc_chip_info, + .chip_select = 4, + .platform_data = &bfin_mmc_spi_pdata, + .controller_data = &mmc_spi_chip_info, .mode = SPI_MODE_3, }, #endif @@ -783,6 +792,17 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = { .mode = SPI_CPHA | SPI_CPOL, }, #endif +#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE) + { + .modalias = "enc28j60", + .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */ + .irq = IRQ_PF6, + .bus_num = 0, + .chip_select = 0, /* GPIO controlled SSEL */ + .controller_data = &enc28j60_spi_chip_info, + .mode = SPI_MODE_0, + }, +#endif }; #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) @@ -885,30 +905,59 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) static struct resource bfin_twi0_resource[] = { @@ -932,6 +981,93 @@ static struct platform_device i2c_bfin_twi_device = { }; #endif +#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE) +#include <linux/input.h> +#include <linux/i2c/adp5588_keys.h> +static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = { + [0] = KEY_GRAVE, + [1] = KEY_1, + [2] = KEY_2, + [3] = KEY_3, + [4] = KEY_4, + [5] = KEY_5, + [6] = KEY_6, + [7] = KEY_7, + [8] = KEY_8, + [9] = KEY_9, + [10] = KEY_0, + [11] = KEY_MINUS, + [12] = KEY_EQUAL, + [13] = KEY_BACKSLASH, + [15] = KEY_KP0, + [16] = KEY_Q, + [17] = KEY_W, + [18] = KEY_E, + [19] = KEY_R, + [20] = KEY_T, + [21] = KEY_Y, + [22] = KEY_U, + [23] = KEY_I, + [24] = KEY_O, + [25] = KEY_P, + [26] = KEY_LEFTBRACE, + [27] = KEY_RIGHTBRACE, + [29] = KEY_KP1, + [30] = KEY_KP2, + [31] = KEY_KP3, + [32] = KEY_A, + [33] = KEY_S, + [34] = KEY_D, + [35] = KEY_F, + [36] = KEY_G, + [37] = KEY_H, + [38] = KEY_J, + [39] = KEY_K, + [40] = KEY_L, + [41] = KEY_SEMICOLON, + [42] = KEY_APOSTROPHE, + [43] = KEY_BACKSLASH, + [45] = KEY_KP4, + [46] = KEY_KP5, + [47] = KEY_KP6, + [48] = KEY_102ND, + [49] = KEY_Z, + [50] = KEY_X, + [51] = KEY_C, + [52] = KEY_V, + [53] = KEY_B, + [54] = KEY_N, + [55] = KEY_M, + [56] = KEY_COMMA, + [57] = KEY_DOT, + [58] = KEY_SLASH, + [60] = KEY_KPDOT, + [61] = KEY_KP7, + [62] = KEY_KP8, + [63] = KEY_KP9, + [64] = KEY_SPACE, + [65] = KEY_BACKSPACE, + [66] = KEY_TAB, + [67] = KEY_KPENTER, + [68] = KEY_ENTER, + [69] = KEY_ESC, + [70] = KEY_DELETE, + [74] = KEY_KPMINUS, + [76] = KEY_UP, + [77] = KEY_DOWN, + [78] = KEY_RIGHT, + [79] = KEY_LEFT, +}; + +static struct adp5588_kpad_platform_data adp5588_kpad_data = { + .rows = 8, + .cols = 10, + .keymap = adp5588_keymap, + .keymapsize = ARRAY_SIZE(adp5588_keymap), + .repeat = 0, +}; +#endif + #ifdef CONFIG_I2C_BOARDINFO static struct i2c_board_info __initdata bfin_i2c_board_info[] = { #if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE) @@ -958,6 +1094,13 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = { .platform_data = (void *)&bfin_ad7879_ts_info, }, #endif +#if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE) + { + I2C_BOARD_INFO("adp5588-keys", 0x34), + .irq = IRQ_PG0, + .platform_data = (void *)&adp5588_kpad_data, + }, +#endif }; #endif @@ -1057,6 +1200,10 @@ static struct platform_device *stamp_devices[] __initdata = { &isp1362_hcd_device, #endif +#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) + &bfin_isp1760_device, +#endif + #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) &smc91x_device, #endif @@ -1098,7 +1245,12 @@ static struct platform_device *stamp_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c index d5ff705a512..2f4b066153c 100644 --- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c +++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c @@ -308,6 +308,19 @@ static struct platform_device net2272_bfin_device = { }; #endif +static struct resource bfin_gpios_resources = { + .start = 0, + .end = MAX_BLACKFIN_GPIOS - 1, + .flags = IORESOURCE_IRQ, +}; + +static struct platform_device bfin_gpios_device = { + .name = "simple-gpio", + .id = -1, + .num_resources = 1, + .resource = &bfin_gpios_resources, +}; + #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) static struct mtd_partition cm_partitions[] = { { @@ -379,30 +392,59 @@ static struct platform_device bfin_uart_device = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -static struct resource bfin_sir_resources[] = { #ifdef CONFIG_BFIN_SIR0 +static struct resource bfin_sir0_resources[] = { { .start = 0xFFC00400, .end = 0xFFC004FF, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX+1, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device bfin_sir0_device = { + .name = "bfin_sir", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_sir0_resources), + .resource = bfin_sir0_resources, +}; #endif #ifdef CONFIG_BFIN_SIR1 +static struct resource bfin_sir1_resources[] = { { .start = 0xFFC02000, .end = 0xFFC020FF, .flags = IORESOURCE_MEM, }, -#endif + { + .start = IRQ_UART1_RX, + .end = IRQ_UART1_RX+1, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART1_RX, + .end = CH_UART1_RX+1, + .flags = IORESOURCE_DMA, + }, }; -static struct platform_device bfin_sir_device = { +static struct platform_device bfin_sir1_device = { .name = "bfin_sir", - .id = 0, - .num_resources = ARRAY_SIZE(bfin_sir_resources), - .resource = bfin_sir_resources, + .id = 1, + .num_resources = ARRAY_SIZE(bfin_sir1_resources), + .resource = bfin_sir1_resources, }; #endif +#endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) static struct resource bfin_twi0_resource[] = { @@ -525,7 +567,12 @@ static struct platform_device *cm_bf537_devices[] __initdata = { #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) - &bfin_sir_device, +#ifdef CONFIG_BFIN_SIR0 + &bfin_sir0_device, +#endif +#ifdef CONFIG_BFIN_SIR1 + &bfin_sir1_device, +#endif #endif #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) @@ -564,6 +611,8 @@ static struct platform_device *cm_bf537_devices[] __initdata = { #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE) &cm_flash_device, #endif + + &bfin_gpios_device, }; static int __init cm_bf537_init(void) diff --git a/arch/blackfin/mach-bf537/dma.c b/arch/blackfin/mach-bf537/dma.c index 4edb363ff99..81185051de9 100644 --- a/arch/blackfin/mach-bf537/dma.c +++ b/arch/blackfin/mach-bf537/dma.c @@ -31,7 +31,7 @@ #include <asm/blackfin.h> #include <asm/dma.h> -struct dma_register *dma_io_base_addr[MAX_BLACKFIN_DMA_CHANNEL] = { +struct dma_register *dma_io_base_addr[MAX_DMA_CHANNELS] = { (struct dma_register *) DMA0_NEXT_DESC_PTR, (struct dma_register *) DMA1_NEXT_DESC_PTR, (struct dma_register *) DMA2_NEXT_DESC_PTR, diff --git a/arch/blackfin/mach-bf537/head.S b/arch/blackfin/mach-bf537/head.S deleted file mode 100644 index f5c94bf80e3..00000000000 --- a/arch/blackfin/mach-bf537/head.S +++ /dev/null @@ -1,146 +0,0 @@ -/* - * File: arch/blackfin/mach-bf537/head.S - * Based on: arch/blackfin/mach-bf533/head.S - * Author: Jeff Dionne <jeff@uclinux.org> COPYRIGHT 1998 D. Jeff Dionne - * - * Created: 1998 - * Description: Startup code for Blackfin BF537 - * - * Modified: - * Copyright 2004-2006 Analog Devices Inc. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, see the file COPYING, or write - * to the Free Software Foundation, Inc., - * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#include <linux/linkage.h> -#include <linux/init.h> -#include <asm/blackfin.h> -#ifdef CONFIG_BFIN_KERNEL_CLOCK -#include <asm/clocks.h> -#include <mach/mem_init.h> -#endif - -.section .l1.text -#ifdef CONFIG_BFIN_KERNEL_CLOCK -ENTRY(_start_dma_code) - - /* Enable PHY CLK buffer output */ - p0.h = hi(VR_CTL); - p0.l = lo(VR_CTL); - r0.l = w[p0]; - bitset(r0, 14); - w[p0] = r0.l; - ssync; - - p0.h = hi(SIC_IWR); - p0.l = lo(SIC_IWR); - r0.l = 0x1; - r0.h = 0x0; - [p0] = r0; - SSYNC; - - /* - * Set PLL_CTL - * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors - * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK - * - [7] = output delay (add 200ps of delay to mem signals) - * - [6] = input delay (add 200ps of input delay to mem signals) - * - [5] = PDWN : 1=All Clocks off - * - [3] = STOPCK : 1=Core Clock off - * - [1] = PLL_OFF : 1=Disable Power to PLL - * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL - * all other bits set to zero - */ - - p0.h = hi(PLL_LOCKCNT); - p0.l = lo(PLL_LOCKCNT); - r0 = 0x300(Z); - w[p0] = r0.l; - ssync; - - P2.H = hi(EBIU_SDGCTL); - P2.L = lo(EBIU_SDGCTL); - R0 = [P2]; - BITSET (R0, 24); - [P2] = R0; - SSYNC; - - r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */ - r0 = r0 << 9; /* Shift it over, */ - r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/ - r0 = r1 | r0; - r1 = PLL_BYPASS; /* Bypass the PLL? */ - r1 = r1 << 8; /* Shift it over */ - r0 = r1 | r0; /* add them all together */ -#ifdef ANOMALY_05000265 - BITSET(r0, 15); /* Add 250 mV of hysteresis to SPORT input pins */ -#endif - - p0.h = hi(PLL_CTL); - p0.l = lo(PLL_CTL); /* Load the address */ - cli r2; /* Disable interrupts */ - ssync; - w[p0] = r0.l; /* Set the value */ - idle; /* Wait for the PLL to stablize */ - sti r2; /* Enable interrupts */ - -.Lcheck_again: - p0.h = hi(PLL_STAT); - p0.l = lo(PLL_STAT); - R0 = W[P0](Z); - CC = BITTST(R0,5); - if ! CC jump .Lcheck_again; - - /* Configure SCLK & CCLK Dividers */ - r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV); - p0.h = hi(PLL_DIV); - p0.l = lo(PLL_DIV); - w[p0] = r0.l; - ssync; - - p0.l = lo(EBIU_SDRRC); - p0.h = hi(EBIU_SDRRC); - r0 = mem_SDRRC; - w[p0] = r0.l; - ssync; - - P2.H = hi(EBIU_SDGCTL); - P2.L = lo(EBIU_SDGCTL); - R0 = [P2]; - BITCLR (R0, 24); - p0.h = hi(EBIU_SDSTAT); - p0.l = lo(EBIU_SDSTAT); - r2.l = w[p0]; - cc = bittst(r2,3); - if !cc jump .Lskip; - NOP; - BITSET (R0, 23); -.Lskip: - [P2] = R0; - SSYNC; - - R0.L = lo(mem_SDGCTL); - R0.H = hi(mem_SDGCTL); - R1 = [p2]; - R1 = R1 | R0; - [P2] = R1; - SSYNC; - - RTS; -ENDPROC(_start_dma_code) -#endif /* CONFIG_BFIN_KERNEL_CLOCK */ diff --git a/arch/blackfin/mach-bf537/include/mach/anomaly.h b/arch/blackfin/mach-bf537/include/mach/anomaly.h index c68992494f9..9cb39121d1c 100644 --- a/arch/blackfin/mach-bf537/include/mach/anomaly.h +++ b/arch/blackfin/mach-bf537/include/mach/anomaly.h @@ -7,7 +7,7 @@ */ /* This file shoule be up to date with: - * - Revision C, 02/08/2008; ADSP-BF534/ADSP-BF536/ADSP-BF537 Blackfin Processor Anomaly List + * - Revision D, 09/18/2008; ADSP-BF534/ADSP-BF536/ADSP-BF537 Blackfin Processor Anomaly List */ #ifndef _MACH_ANOMALY_H_ @@ -148,6 +148,14 @@ #define ANOMALY_05000402 (__SILICON_REVISION__ >= 5) /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */ #define ANOMALY_05000403 (1) +/* Speculative Fetches Can Cause Undesired External FIFO Operations */ +#define ANOMALY_05000416 (1) +/* Multichannel SPORT Channel Misalignment Under Specific Configuration */ +#define ANOMALY_05000425 (1) +/* Speculative Fetches of Indirect-Pointer Instructions Can Cause False Hardware Errors */ +#define ANOMALY_05000426 (1) +/* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */ +#define ANOMALY_05000443 (1) /* Anomalies that don't exist on this proc */ #define ANOMALY_05000125 (0) @@ -161,5 +169,8 @@ #define ANOMALY_05000353 (1) #define ANOMALY_05000363 (0) #define ANOMALY_05000386 (1) +#define ANOMALY_05000412 (0) +#define ANOMALY_05000432 (0) +#define ANOMALY_05000435 (0) #endif diff --git a/arch/blackfin/mach-bf537/include/mach/bf537.h b/arch/blackfin/mach-bf537/include/mach/bf537.h index 24d5c9d4232..f194a848ae8 100644 --- a/arch/blackfin/mach-bf537/include/mach/bf537.h +++ b/arch/blackfin/mach-bf537/include/mach/bf537.h @@ -133,7 +133,7 @@ #endif #ifndef CPU -#error Unknown CPU type - This kernel doesn't seem to be configured properly +#error "Unknown CPU type - This kernel doesn't seem to be configured properly" #endif #endif /* __MACH_BF537_H__ */ diff --git a/arch/blackfin/mach-bf537/include/mach/bfin_sir.h b/arch/blackfin/mach-bf537/include/mach/bfin_sir.h deleted file mode 100644 index cfd8ad4f1f2..00000000000 --- a/arch/blackfin/mach-bf537/include/mach/bfin_sir.h +++ /dev/null @@ -1,142 +0,0 @@ -/* - * Blackfin Infra-red Driver - * - * Copyright 2006-2008 Analog Devices Inc. - * - * Enter bugs at http://blackfin.uclinux.org/ - * - * Licensed under the GPL-2 or later. - * - */ - -#include <linux/serial.h> -#include <asm/dma.h> -#include <asm/portmux.h> - -#define SIR_UART_GET_CHAR(port) bfin_read16((port)->membase + OFFSET_RBR) -#define SIR_UART_GET_DLL(port) bfin_read16((port)->membase + OFFSET_DLL) -#define SIR_UART_GET_IER(port) bfin_read16((port)->membase + OFFSET_IER) -#define SIR_UART_GET_DLH(port) bfin_read16((port)->membase + OFFSET_DLH) -#define SIR_UART_GET_IIR(port) bfin_read16((port)->membase + OFFSET_IIR) -#define SIR_UART_GET_LCR(port) bfin_read16((port)->membase + OFFSET_LCR) -#define SIR_UART_GET_GCTL(port) bfin_read16((port)->membase + OFFSET_GCTL) - -#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v) -#define SIR_UART_PUT_DLL(port, v) bfin_write16(((port)->membase + OFFSET_DLL), v) -#define SIR_UART_PUT_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER), v) -#define SIR_UART_PUT_DLH(port, v) bfin_write16(((port)->membase + OFFSET_DLH), v) -#define SIR_UART_PUT_LCR(port, v) bfin_write16(((port)->membase + OFFSET_LCR), v) -#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v) - -#ifdef CONFIG_SIR_BFIN_DMA -struct dma_rx_buf { - char *buf; - int head; - int tail; - }; -#endif /* CONFIG_SIR_BFIN_DMA */ - -struct bfin_sir_port { - unsigned char __iomem *membase; - unsigned int irq; - unsigned int lsr; - unsigned long clk; - struct net_device *dev; -#ifdef CONFIG_SIR_BFIN_DMA - int tx_done; - struct dma_rx_buf rx_dma_buf; - struct timer_list rx_dma_timer; - int rx_dma_nrows; -#endif /* CONFIG_SIR_BFIN_DMA */ - unsigned int tx_dma_channel; - unsigned int rx_dma_channel; -}; - -struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS]; - -struct bfin_sir_port_res { - unsigned long base_addr; - int irq; - unsigned int rx_dma_channel; - unsigned int tx_dma_channel; -}; - -struct bfin_sir_port_res bfin_sir_port_resource[] = { -#ifdef CONFIG_BFIN_SIR0 - { - 0xFFC00400, - IRQ_UART0_RX, - CH_UART0_RX, - CH_UART0_TX, - }, -#endif -#ifdef CONFIG_BFIN_SIR1 - { - 0xFFC02000, - IRQ_UART1_RX, - CH_UART1_RX, - CH_UART1_TX, - }, -#endif -}; - -int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource); - -struct bfin_sir_self { - struct bfin_sir_port *sir_port; - spinlock_t lock; - unsigned int open; - int speed; - int newspeed; - - struct sk_buff *txskb; - struct sk_buff *rxskb; - struct net_device_stats stats; - struct device *dev; - struct irlap_cb *irlap; - struct qos_info qos; - - iobuff_t tx_buff; - iobuff_t rx_buff; - - struct work_struct work; - int mtt; -}; - -static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port) -{ - unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR); - port->lsr |= (lsr & (BI|FE|PE|OE)); - return lsr | port->lsr; -} - -static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port) -{ - port->lsr = 0; - bfin_read16(port->membase + OFFSET_LSR); -} - -#define DRIVER_NAME "bfin_sir" - -static int bfin_sir_hw_init(void) -{ - int ret = -ENODEV; -#ifdef CONFIG_BFIN_SIR0 - ret = peripheral_request(P_UART0_TX, DRIVER_NAME); - if (ret) - return ret; - ret = peripheral_request(P_UART0_RX, DRIVER_NAME); - if (ret) - return ret; -#endif - -#ifdef CONFIG_BFIN_SIR1 - ret = peripheral_request(P_UART1_TX, DRIVER_NAME); - if (ret) - return ret; - ret = peripheral_request(P_UART1_RX, DRIVER_NAME); - if (ret) - return ret; -#endif - return ret; -} diff --git a/arch/blackfin/mach-bf537/include/mach/blackfin.h b/arch/blackfin/mach-bf537/include/mach/blackfin.h index cffc786b2a2..7d6069c886f 100644 --- a/arch/blackfin/mach-bf537/include/mach/blackfin.h +++ b/arch/blackfin/mach-bf537/include/mach/blackfin.h @@ -82,7 +82,7 @@ #define STATUS_P1 0x02 #define STATUS_P0 0x01 -/* DMA Channnel */ +/* DMA Channel */ #define bfin_read_CH_UART_RX() bfin_read_CH_UART0_RX() #define bfin_write_CH_UART_RX(val) bfin_write_CH_UART0_RX(val) #define CH_UART_RX CH_UART0_RX diff --git a/arch/blackfin/mach-bf537/include/mach/cdefBF534.h b/arch/blackfin/mach-bf537/include/mach/cdefBF534.h index 88d491cd9f3..5f8b5f845be 100644 --- a/arch/blackfin/mach-bf537/include/mach/cdefBF534.h +++ b/arch/blackfin/mach-bf537/include/mach/cdefBF534.h @@ -40,55 +40,11 @@ /* Include core specific register pointer definitions */ #include <asm/cdef_LPBlackfin.h> -#include <asm/system.h> - /* Clock and System Control (0xFFC00000 - 0xFFC000FF) */ #define bfin_read_PLL_CTL() bfin_read16(PLL_CTL) -/* Writing to PLL_CTL initiates a PLL relock sequence. */ -static __inline__ void bfin_write_PLL_CTL(unsigned int val) -{ - unsigned long flags, iwr; - - if (val == bfin_read_PLL_CTL()) - return; - - local_irq_save(flags); - /* Enable the PLL Wakeup bit in SIC IWR */ - iwr = bfin_read32(SIC_IWR); - /* Only allow PPL Wakeup) */ - bfin_write32(SIC_IWR, IWR_ENABLE(0)); - - bfin_write16(PLL_CTL, val); - SSYNC(); - asm("IDLE;"); - - bfin_write32(SIC_IWR, iwr); - local_irq_restore(flags); -} #define bfin_read_PLL_DIV() bfin_read16(PLL_DIV) #define bfin_write_PLL_DIV(val) bfin_write16(PLL_DIV,val) #define bfin_read_VR_CTL() bfin_read16(VR_CTL) -/* Writing to VR_CTL initiates a PLL relock sequence. */ -static __inline__ void bfin_write_VR_CTL(unsigned int val) -{ - unsigned long flags, iwr; - - if (val == bfin_read_VR_CTL()) - return; - - local_irq_save(flags); - /* Enable the PLL Wakeup bit in SIC IWR */ - iwr = bfin_read32(SIC_IWR); - /* Only allow PPL Wakeup) */ - bfin_write32(SIC_IWR, IWR_ENABLE(0)); - - bfin_write16(VR_CTL, val); - SSYNC(); - asm("IDLE;"); - - bfin_write32(SIC_IWR, iwr); - local_irq_restore(flags); -} #define bfin_read_PLL_STAT() bfin_read16(PLL_STAT) #define bfin_write_PLL_STAT(val) bfin_write16(PLL_STAT,val) #define bfin_read_PLL_LOCKCNT() bfin_read16(PLL_LOCKCNT) @@ -1816,4 +1772,51 @@ static __inline__ void bfin_write_VR_CTL(unsigned int val) #define bfin_read_HMDMA1_BCOUNT() bfin_read16(HMDMA1_BCOUNT) #define bfin_write_HMDMA1_BCOUNT(val) bfin_write16(HMDMA1_BCOUNT,val) +/* These need to be last due to the cdef/linux inter-dependencies */ +#include <asm/irq.h> + +/* Writing to PLL_CTL initiates a PLL relock sequence. */ +static __inline__ void bfin_write_PLL_CTL(unsigned int val) +{ + unsigned long flags, iwr; + + if (val == bfin_read_PLL_CTL()) + return; + + local_irq_save_hw(flags); + /* Enable the PLL Wakeup bit in SIC IWR */ + iwr = bfin_read32(SIC_IWR); + /* Only allow PPL Wakeup) */ + bfin_write32(SIC_IWR, IWR_ENABLE(0)); + + bfin_write16(PLL_CTL, val); + SSYNC(); + asm("IDLE;"); + + bfin_write32(SIC_IWR, iwr); + local_irq_restore_hw(flags); +} + +/* Writing to VR_CTL initiates a PLL relock sequence. */ +static __inline__ void bfin_write_VR_CTL(unsigned int val) +{ + unsigned long flags, iwr; + + if (val == bfin_read_VR_CTL()) + return; + + local_irq_save_hw(flags); + /* Enable the PLL Wakeup bit in SIC IWR */ + iwr = bfin_read32(SIC_IWR); + /* Only allow PPL Wakeup) */ + bfin_write32(SIC_IWR, IWR_ENABLE(0)); + + bfin_write16(VR_CTL, val); + SSYNC(); + asm("IDLE;"); + + bfin_write32(SIC_IWR, iwr); + local_irq_restore_hw(flags); +} + #endif /* _CDEF_BF534_H */ diff --git a/arch/blackfin/mach-bf537/include/mach/dma.h b/arch/blackfin/mach-bf537/include/mach/dma.h index 7a964040870..5ae83b1183a 100644 --- a/arch/blackfin/mach-bf537/include/mach/dma.h +++ b/arch/blackfin/mach-bf537/include/mach/dma.h @@ -1,38 +1,14 @@ -/* - * file: include/asm-blackfin/mach-bf537/dma.h - * based on: - * author: +/* mach/dma.h - arch-specific DMA defines * - * created: - * description: - * system mmr register map - * rev: + * Copyright 2004-2008 Analog Devices Inc. * - * modified: - * - * - * bugs: enter bugs at http://blackfin.uclinux.org/ - * - * this program is free software; you can redistribute it and/or modify - * it under the terms of the gnu general public license as published by - * the free software foundation; either version 2, or (at your option) - * any later version. - * - * this program is distributed in the hope that it will be useful, - * but without any warranty; without even the implied warranty of - * merchantability or fitness for a particular purpose. see the - * gnu general public license for more details. - * - * you should have received a copy of the gnu general public license - * along with this program; see the file copying. - * if not, write to the free software foundation, - * 59 temple place - suite 330, boston, ma 02111-1307, usa. + * Licensed under the GPL-2 or later. */ #ifndef _MACH_DMA_H_ #define _MACH_DMA_H_ -#define MAX_BLACKFIN_DMA_CHANNEL 16 +#define MAX_DMA_CHANNELS 16 #define CH_PPI 0 #define CH_EMAC_RX 1 diff --git a/arch/blackfin/mach-bf537/include/mach/gpio.h b/arch/blackfin/mach-bf537/include/mach/gpio.h new file mode 100644 index 00000000000..d77a31e45a3 --- /dev/null +++ b/arch/blackfin/mach-bf537/include/mach/gpio.h @@ -0,0 +1,68 @@ +/* + * File: arch/blackfin/mach-bf537/include/mach/gpio.h + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * Copyright (C) 2008 Analog Devices Inc. + * Licensed under the GPL-2 or later. + */ + + +#ifndef _MACH_GPIO_H_ +#define _MACH_GPIO_H_ + +#define MAX_BLACKFIN_GPIOS 48 + +#define GPIO_PF0 0 +#define GPIO_PF1 1 +#define GPIO_PF2 2 +#define GPIO_PF3 3 +#define GPIO_PF4 4 +#define GPIO_PF5 5 +#define GPIO_PF6 6 +#define GPIO_PF7 7 +#define GPIO_PF8 8 +#define GPIO_PF9 9 +#define GPIO_PF10 10 +#define GPIO_PF11 11 +#define GPIO_PF12 12 +#define GPIO_PF13 13 +#define GPIO_PF14 14 +#define GPIO_PF15 15 +#define GPIO_PG0 16 +#define GPIO_PG1 17 +#define GPIO_PG2 18 +#define GPIO_PG3 19 +#define GPIO_PG4 20 +#define GPIO_PG5 21 +#define GPIO_PG6 22 +#define GPIO_PG7 23 +#define GPIO_PG8 24 +#define GPIO_PG9 25 +#define GPIO_PG10 26 +#define GPIO_PG11 27 +#define GPIO_PG12 28 +#define GPIO_PG13 29 +#define GPIO_PG14 30 +#define GPIO_PG15 31 +#define GPIO_PH0 32 +#define GPIO_PH1 33 +#define GPIO_PH2 34 +#define GPIO_PH3 35 +#define GPIO_PH4 36 +#define GPIO_PH5 37 +#define GPIO_PH6 38 +#define GPIO_PH7 39 +#define GPIO_PH8 40 +#define GPIO_PH9 41 +#define GPIO_PH10 42 +#define GPIO_PH11 43 +#define GPIO_PH12 44 +#define GPIO_PH13 45 +#define GPIO_PH14 46 +#define GPIO_PH15 47 + +#define PORT_F GPIO_PF0 +#define PORT_G GPIO_PG0 +#define PORT_H GPIO_PH0 + +#endif /* _MACH_GPIO_H_ */ diff --git a/arch/blackfin/mach-bf537/include/mach/irq.h b/arch/blackfin/mach-bf537/include/mach/irq.h index 2e68a8a1e73..b2a71d5d4e5 100644 --- a/arch/blackfin/mach-bf537/include/mach/irq.h +++ b/arch/blackfin/mach-bf537/include/mach/irq.h @@ -82,14 +82,14 @@ #define IRQ_CAN_TX 23 /*CAN Transmit Interrupt */ #define IRQ_MAC_RX 24 /*DMA1 (Ethernet RX) Interrupt */ #define IRQ_MAC_TX 25 /*DMA2 (Ethernet TX) Interrupt */ -#define IRQ_TMR0 26 /*Timer 0 */ -#define IRQ_TMR1 27 /*Timer 1 */ -#define IRQ_TMR2 28 /*Timer 2 */ -#define IRQ_TMR3 29 /*Timer 3 */ -#define IRQ_TMR4 30 /*Timer 4 */ -#define IRQ_TMR5 31 /*Timer 5 */ -#define IRQ_TMR6 32 /*Timer 6 */ -#define IRQ_TMR7 33 /*Timer 7 */ +#define IRQ_TIMER0 26 /*Timer 0 */ +#define IRQ_TIMER1 27 /*Timer 1 */ +#define IRQ_TIMER2 28 /*Timer 2 */ +#define IRQ_TIMER3 29 /*Timer 3 */ +#define IRQ_TIMER4 30 /*Timer 4 */ +#define IRQ_TIMER5 31 /*Timer 5 */ +#define IRQ_TIMER6 32 /*Timer 6 */ +#define IRQ_TIMER7 33 /*Timer 7 */ #define IRQ_PROG_INTA 34 /* PF Ports F&G (PF15:0) Interrupt A */ #define IRQ_PORTG_INTB 35 /* PF Port G (PF15:0) Interrupt B */ #define IRQ_MEM_DMA0 36 /*(Memory DMA Stream 0) */ @@ -195,16 +195,16 @@ #define IRQ_CAN_TX_POS 0 #define IRQ_MAC_RX_POS 4 #define IRQ_MAC_TX_POS 8 -#define IRQ_TMR0_POS 12 -#define IRQ_TMR1_POS 16 -#define IRQ_TMR2_POS 20 -#define IRQ_TMR3_POS 24 -#define IRQ_TMR4_POS 28 +#define IRQ_TIMER0_POS 12 +#define IRQ_TIMER1_POS 16 +#define IRQ_TIMER2_POS 20 +#define IRQ_TIMER3_POS 24 +#define IRQ_TIMER4_POS 28 /* IAR3 BIT FIELDS*/ -#define IRQ_TMR5_POS 0 -#define IRQ_TMR6_POS 4 -#define IRQ_TMR7_POS 8 +#define IRQ_TIMER5_POS 0 +#define IRQ_TIMER6_POS 4 +#define IRQ_TIMER7_POS 8 #define IRQ_PROG_INTA_POS 12 #define IRQ_PORTG_INTB_POS 16 #define IRQ_MEM_DMA0_POS 20 diff --git a/arch/blackfin/mach-bf537/include/mach/mem_init.h b/arch/blackfin/mach-bf537/include/mach/mem_init.h deleted file mode 100644 index f67698f670c..00000000000 --- a/arch/blackfin/mach-bf537/include/mach/mem_init.h +++ /dev/null @@ -1,303 +0,0 @@ -/* - * File: include/asm-blackfin/mach-bf537/mem_init.h - * Based on: - * Author: - * - * Created: - * Description: - * - * Rev: - * - * Modified: - * Copyright 2004-2006 Analog Devices Inc. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; see the file COPYING. - * If not, write to the Free Software Foundation, - * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. - */ - -#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_MT48LC16M8A2TG_75 || CONFIG_MEM_GENERIC_BOARD || CONFIG_MEM_MT48LC32M8A2_75) -#if (CONFIG_SCLK_HZ > 119402985) -#define SDRAM_tRP TRP_2 -#define SDRAM_tRP_num 2 -#define SDRAM_tRAS TRAS_7 -#define SDRAM_tRAS_num 7 -#define SDRAM_tRCD TRCD_2 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985) -#define SDRAM_tRP TRP_2 -#define SDRAM_tRP_num 2 -#define SDRAM_tRAS TRAS_6 -#define SDRAM_tRAS_num 6 -#define SDRAM_tRCD TRCD_2 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612) -#define SDRAM_tRP TRP_2 -#define SDRAM_tRP_num 2 -#define SDRAM_tRAS TRAS_5 -#define SDRAM_tRAS_num 5 -#define SDRAM_tRCD TRCD_2 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239) -#define SDRAM_tRP TRP_2 -#define SDRAM_tRP_num 2 -#define SDRAM_tRAS TRAS_4 -#define SDRAM_tRAS_num 4 -#define SDRAM_tRCD TRCD_2 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866) -#define SDRAM_tRP TRP_2 -#define SDRAM_tRP_num 2 -#define SDRAM_tRAS TRAS_3 -#define SDRAM_tRAS_num 3 -#define SDRAM_tRCD TRCD_2 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667) -#define SDRAM_tRP TRP_1 -#define SDRAM_tRP_num 1 -#define SDRAM_tRAS TRAS_4 -#define SDRAM_tRAS_num 3 -#define SDRAM_tRCD TRCD_1 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493) -#define SDRAM_tRP TRP_1 -#define SDRAM_tRP_num 1 -#define SDRAM_tRAS TRAS_3 -#define SDRAM_tRAS_num 3 -#define SDRAM_tRCD TRCD_1 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119) -#define SDRAM_tRP TRP_1 -#define SDRAM_tRP_num 1 -#define SDRAM_tRAS TRAS_2 -#define SDRAM_tRAS_num 2 -#define SDRAM_tRCD TRCD_1 -#define SDRAM_tWR TWR_2 -#endif -#if (CONFIG_SCLK_HZ <= 29850746) -#define SDRAM_tRP TRP_1 -#define SDRAM_tRP_num 1 -#define SDRAM_tRAS TRAS_1 -#define SDRAM_tRAS_num 1 -#define SDRAM_tRCD TRCD_1 -#define SDRAM_tWR TWR_2 -#endif -#endif - -#if (CONFIG_MEM_MT48LC16M16A2TG_75) - /*SDRAM INFORMATION: */ -#define SDRAM_Tref 64 /* Refresh period in milliseconds */ -#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ -#define SDRAM_CL CL_3 -#endif - -#if (CONFIG_MEM_MT48LC16M8A2TG_75) - /*SDRAM INFORMATION: */ -#define SDRAM_Tref 64 /* Refresh period in milliseconds */ -#define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */ -#define SDRAM_CL CL_3 -#endif - -#if (CONFIG_MEM_MT48LC32M8A2_75) - /*SDRAM INFORMATION: */ -#define SDRAM_Tref 64 /* Refresh period in milliseconds */ -#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ -#define SDRAM_CL CL_3 -#endif - -#if (CONFIG_MEM_MT48LC64M4A2FB_7E) - /*SDRAM INFORMATION: */ -#define SDRAM_Tref 64 /* Refresh period in milliseconds */ -#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ -#define SDRAM_CL CL_3 -#endif - -#if (CONFIG_MEM_GENERIC_BOARD) - /*SDRAM INFORMATION: Modify this for your board */ -#define SDRAM_Tref 64 /* Refresh period in milliseconds */ -#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ -#define SDRAM_CL CL_3 -#endif - -/* Equation from section 17 (p17-46) of BF533 HRM */ -#define mem_SDRRC (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num) - -/* Enable SCLK Out */ -#define mem_SDGCTL (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS) - -#if defined CONFIG_CLKIN_HALF -#define CLKIN_HALF 1 -#else -#define CLKIN_HALF 0 -#endif - -#if defined CONFIG_PLL_BYPASS -#define PLL_BYPASS 1 -#else -#define PLL_BYPASS 0 -#endif - -/***************************************Currently Not Being Used *********************************/ -#define flash_EBIU_AMBCTL_WAT ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 -#define flash_EBIU_AMBCTL_RAT ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 -#define flash_EBIU_AMBCTL_HT ((CONFIG_FLASH_SPEED_BHT * 4) / (4000000000 / CONFIG_SCLK_HZ)) -#define flash_EBIU_AMBCTL_ST ((CONFIG_FLASH_SPEED_BST * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 -#define flash_EBIU_AMBCTL_TT ((CONFIG_FLASH_SPEED_BTT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 - -#if (flash_EBIU_AMBCTL_TT > 3) -#define flash_EBIU_AMBCTL0_TT B0TT_4 -#endif -#if (flash_EBIU_AMBCTL_TT == 3) -#define flash_EBIU_AMBCTL0_TT B0TT_3 -#endif -#if (flash_EBIU_AMBCTL_TT == 2) -#define flash_EBIU_AMBCTL0_TT B0TT_2 -#endif -#if (flash_EBIU_AMBCTL_TT < 2) -#define flash_EBIU_AMBCTL0_TT B0TT_1 -#endif - -#if (flash_EBIU_AMBCTL_ST > 3) -#define flash_EBIU_AMBCTL0_ST B0ST_4 -#endif -#if (flash_EBIU_AMBCTL_ST == 3) -#define flash_EBIU_AMBCTL0_ST B0ST_3 -#endif -#if (flash_EBIU_AMBCTL_ST == 2) -#define flash_EBIU_AMBCTL0_ST B0ST_2 -#endif -#if (flash_EBIU_AMBCTL_ST < 2) -#define flash_EBIU_AMBCTL0_ST B0ST_1 -#endif - -#if (flash_EBIU_AMBCTL_HT > 2) -#define flash_EBIU_AMBCTL0_HT B0HT_3 -#endif -#if (flash_EBIU_AMBCTL_HT == 2) -#define flash_EBIU_AMBCTL0_HT B0HT_2 -#endif -#if (flash_EBIU_AMBCTL_HT == 1) -#define flash_EBIU_AMBCTL0_HT B0HT_1 -#endif -#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0) -#define flash_EBIU_AMBCTL0_HT B0HT_0 -#endif -#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0) -#define flash_EBIU_AMBCTL0_HT B0HT_1 -#endif - -#if (flash_EBIU_AMBCTL_WAT > 14) -#define flash_EBIU_AMBCTL0_WAT B0WAT_15 -#endif -#if (flash_EBIU_AMBCTL_WAT == 14) -#define flash_EBIU_AMBCTL0_WAT B0WAT_14 -#endif -#if (flash_EBIU_AMBCTL_WAT == 13) -#define flash_EBIU_AMBCTL0_WAT B0WAT_13 -#endif -#if (flash_EBIU_AMBCTL_WAT == 12) -#define flash_EBIU_AMBCTL0_WAT B0WAT_12 -#endif -#if (flash_EBIU_AMBCTL_WAT == 11) -#define flash_EBIU_AMBCTL0_WAT B0WAT_11 -#endif -#if (flash_EBIU_AMBCTL_WAT == 10) -#define flash_EBIU_AMBCTL0_WAT B0WAT_10 -#endif -#if (flash_EBIU_AMBCTL_WAT == 9) -#define flash_EBIU_AMBCTL0_WAT B0WAT_9 -#endif -#if (flash_EBIU_AMBCTL_WAT == 8) -#define flash_EBIU_AMBCTL0_WAT B0WAT_8 -#endif -#if (flash_EBIU_AMBCTL_WAT == 7) -#define flash_EBIU_AMBCTL0_WAT B0WAT_7 -#endif -#if (flash_EBIU_AMBCTL_WAT == 6) -#define flash_EBIU_AMBCTL0_WAT B0WAT_6 -#endif -#if (flash_EBIU_AMBCTL_WAT == 5) -#define flash_EBIU_AMBCTL0_WAT B0WAT_5 -#endif -#if (flash_EBIU_AMBCTL_WAT == 4) -#define flash_EBIU_AMBCTL0_WAT B0WAT_4 -#endif -#if (flash_EBIU_AMBCTL_WAT == 3) -#define flash_EBIU_AMBCTL0_WAT B0WAT_3 -#endif -#if (flash_EBIU_AMBCTL_WAT == 2) -#define flash_EBIU_AMBCTL0_WAT B0WAT_2 -#endif -#if (flash_EBIU_AMBCTL_WAT == 1) -#define flash_EBIU_AMBCTL0_WAT B0WAT_1 -#endif - -#if (flash_EBIU_AMBCTL_RAT > 14) -#define flash_EBIU_AMBCTL0_RAT B0RAT_15 -#endif -#if (flash_EBIU_AMBCTL_RAT == 14) -#define flash_EBIU_AMBCTL0_RAT B0RAT_14 -#endif -#if (flash_EBIU_AMBCTL_RAT == 13) -#define flash_EBIU_AMBCTL0_RAT B0RAT_13 -#endif -#if (flash_EBIU_AMBCTL_RAT == 12) -#define flash_EBIU_AMBCTL0_RAT B0RAT_12 -#endif -#if (flash_EBIU_AMBCTL_RAT == 11) -#define flash_EBIU_AMBCTL0_RAT B0RAT_11 -#endif -#if (flash_EBIU_AMBCTL_RAT == 10) -#define flash_EBIU_AMBCTL0_RAT B0RAT_10 -#endif -#if (flash_EBIU_AMBCTL_RAT == 9) -#define flash_EBIU_AMBCTL0_RAT B0RAT_9 -#endif -#if (flash_EBIU_AMBCTL_RAT == 8) -#define flash_EBIU_AMBCTL0_RAT B0RAT_8 -#endif -#if (flash_EBIU_AMBCTL_RAT == 7) -#define flash_EBIU_AMBCTL0_RAT B0RAT_7 -#endif -#if (flash_EBIU_AMBCTL_RAT == 6) -#define flash_EBIU_AMBCTL0_RAT B0RAT_6 -#endif -#if (flash_EBIU_AMBCTL_RAT == 5) -#define flash_EBIU_AMBCTL0_RAT B0RAT_5 -#endif -#if (flash_EBIU_AMBCTL_RAT == 4) -#define flash_EBIU_AMBCTL0_RAT B0RAT_4 -#endif -#if (flash_EBIU_AMBCTL_RAT == 3) -#define flash_EBIU_AMBCTL0_RAT B0RAT_3 -#endif -#if (flash_EBIU_AMBCTL_RAT == 2) -#define flash_EBIU_AMBCTL0_RAT B0RAT_2 -#endif -#if (flash_EBIU_AMBCTL_RAT == 1) -#define flash_EBIU_AMBCTL0_RAT B0RAT_1 -#endif - -#define flash_EBIU_AMBCTL0 \ - (flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \ - flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN) diff --git a/arch/blackfin/mach-bf537/include/mach/mem_map.h b/arch/blackfin/mach-bf537/include/mach/mem_map.h index 5078b669431..f9010c4b4bf 100644 --- a/arch/blackfin/mach-bf537/include/mach/mem_map.h +++ b/arch/blackfin/mach-bf537/include/mach/mem_map.h @@ -176,4 +176,10 @@ #define L1_SCRATCH_START 0xFFB00000 #define L1_SCRATCH_LENGTH 0x1000 +#define GET_PDA_SAFE(preg) \ + preg.l = _cpu_pda; \ + preg.h = _cpu_pda; + +#define GET_PDA(preg, dreg) GET_PDA_SAFE(preg) + #endif /* _MEM_MAP_537_H_ */ diff --git a/arch/blackfin/mach-bf537/ints-priority.c b/arch/blackfin/mach-bf537/ints-priority.c index b1300b3f181..51c48087e03 100644 --- a/arch/blackfin/mach-bf537/ints-priority.c +++ b/arch/blackfin/mach-bf537/ints-priority.c @@ -55,15 +55,15 @@ void __init program_IAR(void) bfin_write_SIC_IAR2(((CONFIG_IRQ_CAN_TX - 7) << IRQ_CAN_TX_POS) | ((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) | ((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) | - ((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) | - ((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) | - ((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) | - ((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) | - ((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS)); + ((CONFIG_IRQ_TIMER0 - 7) << IRQ_TIMER0_POS) | + ((CONFIG_IRQ_TIMER1 - 7) << IRQ_TIMER1_POS) | + ((CONFIG_IRQ_TIMER2 - 7) << IRQ_TIMER2_POS) | + ((CONFIG_IRQ_TIMER3 - 7) << IRQ_TIMER3_POS) | + ((CONFIG_IRQ_TIMER4 - 7) << IRQ_TIMER4_POS)); - bfin_write_SIC_IAR3(((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) | - ((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) | - ((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS) | + bfin_write_SIC_IAR3(((CONFIG_IRQ_TIMER5 - 7) << IRQ_TIMER5_POS) | + ((CONFIG_IRQ_TIMER6 - 7) << IRQ_TIMER6_POS) | + ((CONFIG_IRQ_TIMER7 - 7) << IRQ_TIMER7_POS) | ((CONFIG_IRQ_PROG_INTA - 7) << IRQ_PROG_INTA_POS) | ((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) | ((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) | |