diff options
Diffstat (limited to 'arch/cris/Kconfig')
| -rw-r--r-- | arch/cris/Kconfig | 483 |
1 files changed, 443 insertions, 40 deletions
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 27b082ac7f1..0e9926d71a3 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -13,10 +13,6 @@ config ZONE_DMA bool default y -config NO_DMA - bool - default y - config RWSEM_GENERIC_SPINLOCK bool default y @@ -24,6 +20,10 @@ config RWSEM_GENERIC_SPINLOCK config RWSEM_XCHGADD_ALGORITHM bool +config GENERIC_IOMAP + bool + default y + config ARCH_HAS_ILOG2_U32 bool default n @@ -44,13 +44,16 @@ config GENERIC_CALIBRATE_DELAY bool default y -config IRQ_PER_CPU - bool - default y - config NO_IOPORT def_bool y +config NO_IOMEM + def_bool y + +config FORCE_MAX_ZONEORDER + int + default 6 + config CRIS bool default y @@ -93,17 +96,15 @@ config ETRAX_FAST_TIMER timers). This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled. -config PREEMPT - bool "Preemptible Kernel" +config ETRAX_KMALLOCED_MODULES + bool "Enable module allocation with kmalloc" help - This option reduces the latency of the kernel when reacting to - real-time or interactive events by allowing a low priority process to - be preempted even if it is in kernel mode executing a system call. - This allows applications to run more reliably even when the system is - under load. + Enable module allocation with kmalloc instead of vmalloc. + +config OOM_REBOOT + bool "Enable reboot at out of memory" - Say Y here if you are building a kernel for a desktop, embedded - or real-time system. Say N if you are unsure. +source "kernel/Kconfig.preempt" source mm/Kconfig @@ -130,24 +131,124 @@ config SVINTO_SIM help Support the xsim ETRAX Simulator. +config ETRAXFS + bool "ETRAX-FS-V32" + help + Support CRIS V32. + +config CRIS_MACH_ARTPEC3 + bool "ARTPEC-3" + help + Support Axis ARTPEC-3. + endchoice +config ETRAX_VCS_SIM + bool "VCS Simulator" + help + Setup hardware to be run in the VCS simulator. + config ETRAX_ARCH_V10 bool default y if ETRAX100LX || ETRAX100LX_V2 default n if !(ETRAX100LX || ETRAX100LX_V2) +config ETRAX_ARCH_V32 + bool + default y if (ETRAXFS || CRIS_MACH_ARTPEC3) + default n if !(ETRAXFS || CRIS_MACH_ARTPEC3) + config ETRAX_DRAM_SIZE int "DRAM size (dec, in MB)" default "8" help Size of DRAM (decimal in MB) typically 2, 8 or 16. +config ETRAX_VMEM_SIZE + int "Video memory size (dec, in MB)" + depends on ETRAX_ARCH_V32 && !ETRAXFS + default 8 if !ETRAXFS + help + Size of Video accessible memory (decimal, in MB). + config ETRAX_FLASH_BUSWIDTH - int "Buswidth of flash in bytes" + int "Buswidth of NOR flash in bytes" default "2" help - Width in bytes of the Flash bus (1, 2 or 4). Is usually 2. + Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2. + +config ETRAX_NANDFLASH_BUSWIDTH + int "Buswidth of NAND flash in bytes" + default "1" + help + Width in bytes of the NAND flash (1 or 2). + +config ETRAX_FLASH1_SIZE + int "FLASH1 size (dec, in MB. 0 = Unknown)" + default "0" + +choice + prompt "Product debug-port" + default ETRAX_DEBUG_PORT0 + +config ETRAX_DEBUG_PORT0 + bool "Serial-0" + help + Choose a serial port for the ETRAX debug console. Default to + port 0. + +config ETRAX_DEBUG_PORT1 + bool "Serial-1" + help + Use serial port 1 for the console. + +config ETRAX_DEBUG_PORT2 + bool "Serial-2" + help + Use serial port 2 for the console. + +config ETRAX_DEBUG_PORT3 + bool "Serial-3" + help + Use serial port 3 for the console. + +config ETRAX_DEBUG_PORT_NULL + bool "disabled" + help + Disable serial-port debugging. + +endchoice + +choice + prompt "Kernel GDB port" + depends on ETRAX_KGDB + default ETRAX_KGDB_PORT0 + help + Choose a serial port for kernel debugging. NOTE: This port should + not be enabled under Drivers for built-in interfaces (as it has its + own initialization code) and should not be the same as the debug port. + +config ETRAX_KGDB_PORT0 + bool "Serial-0" + help + Use serial port 0 for kernel debugging. + +config ETRAX_KGDB_PORT1 + bool "Serial-1" + help + Use serial port 1 for kernel debugging. + +config ETRAX_KGDB_PORT2 + bool "Serial-2" + help + Use serial port 2 for kernel debugging. + +config ETRAX_KGDB_PORT3 + bool "Serial-3" + help + Use serial port 3 for kernel debugging. + +endchoice source arch/cris/arch-v10/Kconfig source arch/cris/arch-v32/Kconfig @@ -161,6 +262,329 @@ menu "Drivers for built-in interfaces" source arch/cris/arch-v10/drivers/Kconfig source arch/cris/arch-v32/drivers/Kconfig +choice + prompt "RTC chip" + depends on ETRAX_RTC + default ETRAX_PCF8563 if ETRAX_ARCH_V32 + default ETRAX_DS1302 if ETRAX_ARCH_V10 + +config ETRAX_DS1302 + depends on ETRAX_ARCH_V10 + bool "DS1302" + help + Enables the driver for the DS1302 Real-Time Clock battery-backed + chip on some products. + +config ETRAX_PCF8563 + bool "PCF8563" + help + Enables the driver for the PCF8563 Real-Time Clock battery-backed + chip on some products. + +endchoice + +choice + prompt "Network LED behavior" + depends on ETRAX_ETHERNET + default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY + +config ETRAX_NETWORK_LED_ON_WHEN_LINK + bool "LED_on_when_link" + help + Selecting LED_on_when_link will light the LED when there is a + connection and will flash off when there is activity. + + Selecting LED_on_when_activity will light the LED only when + there is activity. + + This setting will also affect the behaviour of other activity LEDs + e.g. Bluetooth. + +config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY + bool "LED_on_when_activity" + help + Selecting LED_on_when_link will light the LED when there is a + connection and will flash off when there is activity. + + Selecting LED_on_when_activity will light the LED only when + there is activity. + + This setting will also affect the behaviour of other activity LEDs + e.g. Bluetooth. + +endchoice + +choice + prompt "Ser0 DMA out channel" + depends on ETRAX_SERIAL_PORT0 + default ETRAX_SERIAL_PORT0_DMA6_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT0_NO_DMA_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT0_NO_DMA_OUT + bool "Ser0 uses no DMA for output" + help + Do not use DMA for ser0 output. + +config ETRAX_SERIAL_PORT0_DMA6_OUT + bool "Ser0 uses DMA6 for output" + depends on ETRAXFS + help + Enables the DMA6 output channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT0_DMA0_OUT + bool "Ser0 uses DMA0 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA0 output channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser0 DMA in channel " + depends on ETRAX_SERIAL_PORT0 + default ETRAX_SERIAL_PORT0_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT0_DMA7_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser0. + +config ETRAX_SERIAL_PORT0_NO_DMA_IN + bool "Ser0 uses no DMA for input" + help + Do not use DMA for ser0 input. + +config ETRAX_SERIAL_PORT0_DMA7_IN + bool "Ser0 uses DMA7 for input" + depends on ETRAXFS + help + Enables the DMA7 input channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT0_DMA1_IN + bool "Ser0 uses DMA1 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA1 input channel for ser0 (ttyS0). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser1 DMA in channel " + depends on ETRAX_SERIAL_PORT1 + default ETRAX_SERIAL_PORT1_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT1_DMA9_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser1. + +config ETRAX_SERIAL_PORT1_NO_DMA_IN + bool "Ser1 uses no DMA for input" + help + Do not use DMA for ser1 input. + +config ETRAX_SERIAL_PORT1_DMA5_IN + bool "Ser1 uses DMA5 for input" + depends on ETRAX_ARCH_V32 + help + Enables the DMA5 input channel for ser1 (ttyS1). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want this on, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT1_DMA9_IN + depends on ETRAX_ARCH_V10 + bool "Ser1 uses DMA9 for input" + +endchoice + + +choice + prompt "Ser1 DMA out channel" + depends on ETRAX_SERIAL_PORT1 + default ETRAX_SERIAL_PORT1_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT1_DMA8_OUT if ETRAX_ARCH_V10 + help + What DMA channel to use for ser1. + +config ETRAX_SERIAL_PORT1_NO_DMA_OUT + bool "Ser1 uses no DMA for output" + help + Do not use DMA for ser1 output. + +config ETRAX_SERIAL_PORT1_DMA8_OUT + depends on ETRAX_ARCH_V10 + bool "Ser1 uses DMA8 for output" + +config ETRAX_SERIAL_PORT1_DMA4_OUT + depends on ETRAX_ARCH_V32 + bool "Ser1 uses DMA4 for output" + help + Enables the DMA4 output channel for ser1 (ttyS1). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want this on, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser2 DMA out channel" + depends on ETRAX_SERIAL_PORT2 + default ETRAX_SERIAL_PORT2_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT2_DMA2_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT2_NO_DMA_OUT + bool "Ser2 uses no DMA for output" + help + Do not use DMA for ser2 output. + +config ETRAX_SERIAL_PORT2_DMA2_OUT + bool "Ser2 uses DMA2 for output" + depends on ETRAXFS || ETRAX_ARCH_V10 + help + Enables the DMA2 output channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT2_DMA6_OUT + bool "Ser2 uses DMA6 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA6 output channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser2 DMA in channel" + depends on ETRAX_SERIAL_PORT2 + default ETRAX_SERIAL_PORT2_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT2_DMA3_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser2. + +config ETRAX_SERIAL_PORT2_NO_DMA_IN + bool "Ser2 uses no DMA for input" + help + Do not use DMA for ser2 input. + +config ETRAX_SERIAL_PORT2_DMA3_IN + bool "Ser2 uses DMA3 for input" + depends on ETRAXFS || ETRAX_ARCH_V10 + help + Enables the DMA3 input channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT2_DMA7_IN + bool "Ser2 uses DMA7 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA7 input channel for ser2 (ttyS2). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser3 DMA in channel" + depends on ETRAX_SERIAL_PORT3 + default ETRAX_SERIAL_PORT3_NO_DMA_IN if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT3_DMA5_IN if ETRAX_ARCH_V10 + help + What DMA channel to use for ser3. + +config ETRAX_SERIAL_PORT3_NO_DMA_IN + bool "Ser3 uses no DMA for input" + help + Do not use DMA for ser3 input. + +config ETRAX_SERIAL_PORT3_DMA5_IN + depends on ETRAX_ARCH_V10 + bool "DMA 5" + +config ETRAX_SERIAL_PORT3_DMA9_IN + bool "Ser3 uses DMA9 for input" + depends on ETRAXFS + help + Enables the DMA9 input channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when receiving data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT3_DMA3_IN + bool "Ser3 uses DMA3 for input" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA3 input channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when receiveing data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + +choice + prompt "Ser3 DMA out channel" + depends on ETRAX_SERIAL_PORT3 + default ETRAX_SERIAL_PORT3_NO_DMA_OUT if ETRAX_ARCH_V32 + default ETRAX_SERIAL_PORT3_DMA4_OUT if ETRAX_ARCH_V10 + +config ETRAX_SERIAL_PORT3_NO_DMA_OUT + bool "Ser3 uses no DMA for output" + help + Do not use DMA for ser3 output. + +config ETRAX_SERIAL_PORT3_DMA4_OUT + depends on ETRAX_ARCH_V10 + bool "DMA 4" + +config ETRAX_SERIAL_PORT3_DMA8_OUT + bool "Ser3 uses DMA8 for output" + depends on ETRAXFS + help + Enables the DMA8 output channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +config ETRAX_SERIAL_PORT3_DMA2_OUT + bool "Ser3 uses DMA2 for output" + depends on CRIS_MACH_ARTPEC3 + help + Enables the DMA2 output channel for ser3 (ttyS3). + If you do not enable DMA, an interrupt for each character will be + used when transmitting data. + Normally you want to use DMA, unless you use the DMA channel for + something else. + +endchoice + endmenu source "drivers/base/Kconfig" @@ -174,22 +598,10 @@ source "drivers/pnp/Kconfig" source "drivers/block/Kconfig" -source "drivers/md/Kconfig" - source "drivers/ide/Kconfig" -source "drivers/scsi/Kconfig" - -source "drivers/ieee1394/Kconfig" - -source "drivers/message/i2o/Kconfig" - source "drivers/net/Kconfig" -source "drivers/isdn/Kconfig" - -source "drivers/telephony/Kconfig" - source "drivers/i2c/Kconfig" source "drivers/rtc/Kconfig" @@ -201,17 +613,8 @@ source "drivers/input/Kconfig" source "drivers/char/Kconfig" -#source drivers/misc/Config.in -source "drivers/media/Kconfig" - source "fs/Kconfig" -source "sound/Kconfig" - -source "drivers/pcmcia/Kconfig" - -source "drivers/pci/Kconfig" - source "drivers/usb/Kconfig" source "arch/cris/Kconfig.debug" |