diff options
Diffstat (limited to 'arch/cris/arch-v10/lib/dram_init.S')
| -rw-r--r-- | arch/cris/arch-v10/lib/dram_init.S | 40 |
1 files changed, 18 insertions, 22 deletions
diff --git a/arch/cris/arch-v10/lib/dram_init.S b/arch/cris/arch-v10/lib/dram_init.S index b9190ff7d0a..e541d3d8f92 100644 --- a/arch/cris/arch-v10/lib/dram_init.S +++ b/arch/cris/arch-v10/lib/dram_init.S @@ -5,9 +5,7 @@ * Note: This file may not modify r9 because r9 is used to carry * information from the decompresser to the kernel * - * Copyright (C) 2000, 2001 Axis Communications AB - * - * Authors: Mikael Starvik (starvik@axis.com) + * Copyright (C) 2000-2012 Axis Communications AB * */ @@ -18,16 +16,15 @@ ;; WARNING! The registers r8 and r9 are used as parameters carrying - ;; information from the decompressor (if the kernel was compressed). + ;; information from the decompressor (if the kernel was compressed). ;; They should not be used in the code below. -#ifndef CONFIG_SVINTO_SIM move.d CONFIG_ETRAX_DEF_R_WAITSTATES, $r0 move.d $r0, [R_WAITSTATES] move.d CONFIG_ETRAX_DEF_R_BUS_CONFIG, $r0 move.d $r0, [R_BUS_CONFIG] - + #ifndef CONFIG_ETRAX_SDRAM move.d CONFIG_ETRAX_DEF_R_DRAM_CONFIG, $r0 move.d $r0, [R_DRAM_CONFIG] @@ -38,14 +35,14 @@ ;; Samsung SDRAMs seem to require to be initialized twice to work properly. moveq 2, $r6 _sdram_init: - + ; Refer to ETRAX 100LX Designers Reference for a description of SDRAM initialization - + ; Bank configuration move.d CONFIG_ETRAX_DEF_R_SDRAM_CONFIG, $r0 move.d $r0, [R_SDRAM_CONFIG] - ; Calculate value of mrs_data + ; Calculate value of mrs_data ; CAS latency = 2 && bus_width = 32 => 0x40 ; CAS latency = 3 && bus_width = 32 => 0x60 ; CAS latency = 2 && bus_width = 16 => 0x20 @@ -56,22 +53,22 @@ _sdram_init: and.d 0x00ff0000, $r2 bne _set_timing lsrq 16, $r2 - + move.d 0x40, $r2 ; Assume 32 bits and CAS latency = 2 move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 move.d $r1, $r3 - and.d 0x03, $r1 ; Get CAS latency + and.d 0x03, $r1 ; Get CAS latency and.d 0x1000, $r3 ; 50 or 100 MHz? beq _speed_50 nop -_speed_100: +_speed_100: cmp.d 0x00, $r1 ; CAS latency = 2? beq _bw_check nop - or.d 0x20, $r2 ; CAS latency = 3 + or.d 0x20, $r2 ; CAS latency = 3 ba _bw_check nop -_speed_50: +_speed_50: cmp.d 0x01, $r1 ; CAS latency = 2? beq _bw_check nop @@ -86,19 +83,19 @@ _bw_check: ; Set timing parameters. Starts master clock _set_timing: move.d CONFIG_ETRAX_DEF_R_SDRAM_TIMING, $r1 - and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0 + and.d 0x8000f9ff, $r1 ; Make sure mrs data and command is 0 or.d 0x80000000, $r1 ; Make sure sdram enable bit is set move.d $r1, $r5 or.d 0x0000c000, $r1 ; ref = disable lslq 16, $r2 ; mrs data starts at bit 16 - or.d $r2, $r1 - move.d $r1, [R_SDRAM_TIMING] - + or.d $r2, $r1 + move.d $r1, [R_SDRAM_TIMING] + ; Wait 200us move.d 10000, $r2 1: bne 1b subq 1, $r2 - + ; Issue initialization command sequence move.d _sdram_commands_start, $r2 and.d 0x000fffff, $r2 ; Make sure commands are read from flash @@ -144,7 +141,6 @@ _sdram_commands_start: .byte 2 ; refresh .byte 0 ; nop .byte 1 ; mrs - .byte 0 ; nop -_sdram_commands_end: -#endif + .byte 0 ; nop +_sdram_commands_end: #endif |