diff options
Diffstat (limited to 'arch/i386/Kconfig')
| -rw-r--r-- | arch/i386/Kconfig | 78 |
1 files changed, 48 insertions, 30 deletions
diff --git a/arch/i386/Kconfig b/arch/i386/Kconfig index 968fabd8723..cbde675bc95 100644 --- a/arch/i386/Kconfig +++ b/arch/i386/Kconfig @@ -29,10 +29,6 @@ config MMU config SBUS bool -config UID16 - bool - default y - config GENERIC_ISA_DMA bool default y @@ -45,8 +41,21 @@ config ARCH_MAY_HAVE_PC_FDC bool default y +config DMI + bool + default y + source "init/Kconfig" +config DOUBLEFAULT + default y + bool "Enable doublefault exception handler" if EMBEDDED + help + This option allows trapping of rare doublefault exceptions that + would otherwise cause a system to silently reboot. Disabling this + option saves about 4k and might cause you much additional grey + hair. + menu "Processor type and features" choice @@ -630,10 +639,6 @@ config REGPARM and passes the first three arguments of a function call in registers. This will probably break binary only modules. - This feature is only enabled for gcc-3.0 and later - earlier compilers - generate incorrect output with certain kernel constructs when - -mregparm=3 is used. - config SECCOMP bool "Enable seccomp to safely compute untrusted bytecode" depends on PROC_FS @@ -653,17 +658,6 @@ config SECCOMP source kernel/Kconfig.hz -config PHYSICAL_START - hex "Physical address where the kernel is loaded" if EMBEDDED - default "0x100000" - help - This gives the physical address where the kernel is loaded. - Primarily used in the case of kexec on panic where the - fail safe kernel needs to run at a different address than - the panic-ed kernel. - - Don't change this unless you know what you are doing. - config KEXEC bool "kexec system call (EXPERIMENTAL)" depends on EXPERIMENTAL @@ -683,11 +677,40 @@ config KEXEC config CRASH_DUMP bool "kernel crash dumps (EXPERIMENTAL)" - depends on EMBEDDED depends on EXPERIMENTAL depends on HIGHMEM help Generate crash dump after being started by kexec. + +config PHYSICAL_START + hex "Physical address where the kernel is loaded" if (EMBEDDED || CRASH_DUMP) + + default "0x1000000" if CRASH_DUMP + default "0x100000" + help + This gives the physical address where the kernel is loaded. Normally + for regular kernels this value is 0x100000 (1MB). But in the case + of kexec on panic the fail safe kernel needs to run at a different + address than the panic-ed kernel. This option is used to set the load + address for kernels used to capture crash dump on being kexec'ed + after panic. The default value for crash dump kernels is + 0x1000000 (16MB). This can also be set based on the "X" value as + specified in the "crashkernel=YM@XM" command line boot parameter + passed to the panic-ed kernel. Typically this parameter is set as + crashkernel=64M@16M. Please take a look at + Documentation/kdump/kdump.txt for more details about crash dumps. + + Don't change this unless you know what you are doing. + +config HOTPLUG_CPU + bool "Support for hot-pluggable CPUs (EXPERIMENTAL)" + depends on SMP && HOTPLUG && EXPERIMENTAL + ---help--- + Say Y here to experiment with turning CPUs off and on. CPUs + can be controlled through /sys/devices/system/cpu. + + Say N. + endmenu @@ -703,7 +726,7 @@ depends on PM && !X86_VISWS config APM tristate "APM (Advanced Power Management) BIOS support" - depends on PM && PM_LEGACY + depends on PM ---help--- APM is a BIOS specification for saving power using several different techniques. This is mostly useful for battery powered laptops with @@ -974,15 +997,6 @@ config SCx200 This support is also available as a module. If compiled as a module, it will be called scx200. -config HOTPLUG_CPU - bool "Support for hot-pluggable CPUs (EXPERIMENTAL)" - depends on SMP && HOTPLUG && EXPERIMENTAL - ---help--- - Say Y here to experiment with turning CPUs off and on. CPUs - can be controlled through /sys/devices/system/cpu. - - Say N. - source "drivers/pcmcia/Kconfig" source "drivers/pci/hotplug/Kconfig" @@ -1059,3 +1073,7 @@ config X86_TRAMPOLINE bool depends on X86_SMP || (X86_VOYAGER && SMP) default y + +config KTIME_SCALAR + bool + default y |